2BCT5-5810072 in 1 Wireless charger

* It can only support 1 device charging at the same time, can not support 2 devices charging at the same time This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

DongguanYOUElectronicTechnologyCo.,Ltd 2.911(d)(5)(ii)ApplicantAttestationv1.3 Section2.911(d)(5)(ii)Certification–Applicant(CoveredList) Companyname:DongguanYOUElectronicTechnologyCo.,Ltd Address:Room201,Building1,No.2,ShengqiangangNo.3street,HuangjiangTown,DongguanCity, GuangdongProvince,China ProductName:2in1Wirelesscharger FCCID:2BCT5-581007 Model(s):581007,YWC-65 2.911(d)(5)(ii)Applicantfiling We,DongguanYOUElectronicTechnologyCo.,Ltd(“theapplicant”)certifythat,asofthedateofthe filingoftheapplication,theapplicantisnotidentified NOTE1 onthe“CoveredList” NOTE2 ,established pursuantto§1.50002ofthischapter,asanentityproducingcoveredcommunicationsequipment. Yourssincerely, Name:AngelaWangDate:2023.09.12 TitleandCompanyname:N/A/DongguanYOUElectronicTechnologyCo.,Ltd NOTE1 Deleteoptionnotapplicabletothisapplication. NOTE2 “CoveredList”;istheListofEquipmentandServicesCoveredBySection2ofTheSecureNetworksAct,availableat https://www.fcc.gov/supplychain/coveredlist References; 1)986446D01CoveredEquipmentv01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2)FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

DongguanYOUElectronicTechnologyCo.,Ltd 2.911(d)(5)(i)EquipmentTypeAttestationv1.2 Section2.911(d)(5)(i)Certification–EquipmentType Companyname:DongguanYOUElectronicTechnologyCo.,Ltd Address:Room201,Building1,No.2,ShengqiangangNo.3street,HuangjiangTown,DongguanCity, GuangdongProvince,China ProductName:2in1Wirelesscharger FCCID:2BCT5-581007 Model(s):581007,YWC-65 2.911(d)(5)(i)EquipmentType We,DongguanYOUElectronicTechnologyCo.,Ltd(“theapplicant”)certifythattheequipmentfor whichauthorizationissoughtthroughcertificationisnot:  Prohibitedfromreceivinganequipmentauthorizationpursuantto§2.903;oftheFCCrules.  Identifiedasanequipmenttypeinthe“CoveredList” NOTE1 Yourssincerely, Name:AngelaWangDate:2023.09.12 TitleandCompanyname:N/A/DongguanYOUElectronicTechnologyCo.,Ltd NOTE1 “CoveredList”;istheListofEquipmentandServicesCoveredBySection2ofTheSecureNetworksAct,availableat https://www.fcc.gov/supplychain/coveredlist References; 1)986446D01CoveredEquipmentv01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2)FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Dongguan YOU Electronic Technology Co.,Ltd 2.911 (d)(7)USA Agent v1.4 Section 2.911(d)(7) USA Agent for Service of Process Company name:Dongguan YOU Electronic Technology Co.,Ltd Address:Room 201, Building 1,No.2,Shengqiangang No.3 street, Huangjiang Town, Dongguan City, Guangdong Province, China Product Name:2 in 1 Wireless charger FCC ID:2BCT5-581007 Model(s):581007, YWC-65 2.911(d)(7) USA Designated Agent for Service of Process We, Dongguan YOU Electronic Technology Co.,Ltd (“the applicant”) designate [Stone Trading Limited] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either we the grantee have permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Company name: Stone Trading Limited USA Address: 6547 N Academy Blvd #2266, Colorado Springs, CO 80918, United States FRN Number: 0033401936 Contact Name: Dongmei Fang Telephone No: +12134573118 Email: [email protected] Applicant Company name:Dongguan YOU Electronic Technology Co.,Ltd Address:Room 201, Building 1,No.2,Shengqiangang No.3 street, Huangjiang Town, Dongguan City, Guangdong Province, China FCC Grantee Code:2BCT5 Contact Name:Angela Wang Telephone No:13423459956 Email:[email protected] Signature: Title: Manager Signature: Title:N/A Date: 2023.09.12 Date:2023.09.12 Dongguan YOU Electronic Technology Co.,Ltd 2.911 (d)(7)USA Agent v1.4 NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-nation al-security-threats-to-the-communications-supply-chain-through-the

DongguanYOUElectronicTechnologyCo.,Ltd AgentAuthorization Company:DongguanYOUElectronicTechnologyCo.,Ltd Address:Room201,Building1,No.2,ShengqiangangNo.3street,HuangjiangTown, DongguanCity,GuangdongProvince,China ProductName:2in1Wirelesscharger ModelNumber(s):581007,YWC-65 ProductDescription:2in1Wirelesscharger WeauthorizeMiCOMLabsInc.,575BoulderCourt,Pleasanton,California94566,USA, toactonourbehalfonallmattersconcerningthecertificationofabovenamed equipment. WedeclarethatMiCOMLabsInc.isallowedtoforwardallinformationrelatedtothe approvalandcertificationofequipmenttotheregulatoryagenciesasrequiredandto discussanyissuesconcerningtheapprovalapplication.Anyandallactscarriedoutby MiCOMLabsonourbehalfshallhavethesameeffectasactsofourown. Signature:Date:2023.09.12 Name:AngelaWang Title:N/A Company:DongguanYOUElectronicTechnologyCo.,Ltd

DongguanYOUElectronicTechnologyCo.,Ltd OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date:2023.09.12 Subject;RequestforConfidentiality FCCID:2BCT5-581007 ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram PartsList OperationalDescription Tune-upProcedure Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely, Signature: Name:AngelaWang Title:N/A

DongguanYOUElectronicTechnologyCo.,Ltd ModelDifference Productdescription:Wirelesscharger Modelname:581007 YWC-65 TradeName:2in1Wirelesscharger AllthemodelarethesamecircuitandRFmodule,onlythemodelnameisdifferent. Regards Sincerely Client’ssignature: Client’sname/title:AngelaWang/N/A Contactinformation/address:13423459956/Room201,Building 1,No.2,ShengqiangangNo.3street,HuangjiangTown,DongguanCity,Guangdong Province,China

EUTPHOTO(ExternalPhotos) 2in1Wirelesscharger FCCID:2BCT5-581007 ※※※※※ENDOFREPORT※※※※※

2 in 1 Wire FCC ID:2B 4cm eless charge BCT5-58100 L er 07 3cm Label an m nd label location

EUTPHOTO(InternalPhotos) 2in1Wirelesscharger FCCID:2BCT5-581007 COIL1 COIL2 ※※※※※ENDOFREPORT※※※※※

FCC ID:2BCT5-581007 Product Name: 2 in 1 Wireless charger Product Model No.: 581007 Test Auxiliary: Notebook, iWatch, Airpod Test Auxiliary Model No.: NP-RC510,S4,AirPods Pro 2 Transmitting mode Keep the EUT in continuously wireless charging mode Power supply: Input: 5V 1A, 5V2A Airpod Wireless Output: 5W(Max) Apple Watch Magnetic Wireless Output: 2.5W(Max) Battery Capacity: N/A Test Modes: Description: Mode 1 Airpod+Coil-1 Full Load Battery≥98% Record Half Load Battery=50% No Load Battery≤1% Note: All modes have been tested, and the report only reflects the worst case data. Test Modes: Description: Mode 2 iWatch+Coil-2 Full Load Battery≥98% Record Half Load Battery=50% No Load Battery≤1% Note: All modes have been tested, and the report only reflects the worst case data. RF Exposure Evaluation 1 Measuring Standard 1.1 KDB 680106 RF Exposure Wireless Charging Apps v03r01 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ±U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainly 1 H-filed ±0.93dB 2 E-filed ±0.51dB 2 Requirements According to the item 5 of KDB 680106 v03r01: Inductive wireless power transfer applications that meet all of the following requirements are excluded from submitting an RF exposure evaluation. a) Power transfer frequency is less that 1 MHz Yes. The device operates in the frequency Airpod Wireless:115KHz-205KHz, Apple Watch Magnetic Wireless:115KHz-333KHz. b) Output power from each primary coil is less than or equal to 15watts. Yes, The maximum output power of Airpod Wireless Output: 5W(Max), Apple Watch Magnetic Wireless Output: 2.5W(Max) c) The transfer system includes onle single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. Yes. The transfer system including a charging system with only single primary coils is to detect and allow only between individual of coils d) Client device is placed directly in contact with the transmitter Yes. Client device is placed directly in contact with the transmitter e) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion) No. The EUT has portable exposure condition. f) The aggregate H-Field strengths at 15 cm surrounding the device and 20 cm above the top surface form all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit Yes. Meet the requirement. Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) 3 Test Setup Note: Measurements should be made from all sides and the top of the primary/client pair, with the 20 cm-0cm measured from the center of the top, and 20cm-0cm measured from the center of the rest For mobile exposure conditions: a. The RF exposure test was performed in anechoic chamber b. E and H-field measurements should be made with the center of the probe at a distance of 15 cm surrounding the EUT and 20 cm above the top surface of the primarv/client pair c. The highest emission level was recorded and compared with limit d. The EUT was measured according to the dictates of KDB680106 v03r01 For portable exposure conditions: a. The RF exposure test was performed in anechoic chamber b. E and H-field measurements should be made with the probe at O cmfor all side of the EUT. c. The highest emission level was recorded and compared with limit. For portable exposure conditions: Perform H-field measurements for each edge/top surface of the host/client pair at every 2 cmstartino from as close as possible out to10cm 4 Test Procedure 1) The RF exposure test was performed on 360 degree turn table in anechoic chamber. 2) 20 cm-0cm measured from the center of the top, and 20cm-0cm measured from the center of the rest sides. 3) The turn table was rotated 360d degree to search of highest strength. 4) The highest emission level was recorded and compared with limit as soon as measurement of each points were completed. 5) The EUT were measured according to the dictates of KDB 680106-v03 5 Test Instruments list Test Equipment Manufacturer Model No. SN. Cal.Date (mm-dd-yy) Cal.Due date (mm-dd-yy) Electric and Magnetic field Probe-Analyzer Narda EHP 200A 19SN0980 2023.03.08 2024.03.07 6 Test Result Apple Watch Magnetic Wireless H-Filed Strength at 20 cm from the edges surrounding the EUT (A/m) H-Filed Strength at 18 cm from the edges surrounding the EUT (A/m) H-Filed Strength at 16 cm from the edges surrounding the EUT (A/m) H-Filed Strength at 14 cm from the edges surrounding the EUT (A/m) H-Filed Strength at 12 cm from the edges surrounding the EUT (A/m) H-Filed Strength at 10 cm from the edges surrounding the EUT (A/m) Frequency Range (MHz) Test Position Left Test Position Right Test Position Bottom Test Position Rear Test Position Front Test Position Top Limits (A/m) 0.115-0.333 0.18 0.17 0.16 0.19 0.20 0.19 1.63 Frequency Range (MHz) Test Position Left Test Position Right Test Position Bottom Test Position Rear Test Position Front Test Position Top Limits (A/m) 0.115-0.333 0.22 0.23 0.21 0.24 0.22 0.25 1.63 Frequency Range (MHz) Test Position Left Test Position Right Test Position Bottom Test Position Rear Test Position Front Test Position Top Limits (A/m) 0.115-0.333 0.24 0.26 0.25 0.28 0.27 0.26 1.63 Frequency Range (MHz) Test Position Left Test Position Right Test Position Bottom Test Position Rear Test Position Front Test Position Top Limits (A/m) 0.115-0.333 0.29 0.31 0.33 0.32 0.34 0.32 1.63 Frequency Range (MHz) Test Position Left Test Position Right Test Position Bottom Test Position Rear Test Position Front Test Position Top Limits (A/m) 0.115-0.333 0.36 0.38 0.35 0.34 0.39 0.37 1.63 Frequency Range (M…

Text truncated - open the document above for the full version.

One、Planestructurediagram：(Tolerance±1)Unit:MM 20.5±0.5 3±1 18±2 隔磁片厚1.0mm 50 5.3±0.2 Two：Productspecs Pin-outWirediameterTurns S--F0.08*10510 Frequency range 115~333KHz Three、Technicalrequirements： 1.Attach8MMhightemperatureadhesivepapertothecorrespondingpositionofthe coil,andfixthewireendtopreventthewirefrombeingloose. 2.Accordingtocustomerrequirements,thelongthreadiscutandtinned,andthe tinningdepthis3±1MM. 3.Pointtheappropriatewhiteglueonthemagneticsheet,attachthecoil,andensure thattheproductsurfaceiscleanandtidyduringtheprocess. 4.Themagneticsheetusedisslottedwithroundholes,modelG50,size50X5X1.0, withoutdamage. 5.Additionalconditions:Attachthecorrespondingdouble-sidedtapeaccordingto Customer’srequirements. Thickness:1.0mm Four、Electricalparameter： 1.Inductancevalue： PINS—F=6.5uH±0.3uH TheaboveinductancevaluesarebasedonQuanhua1062instrument, 1KHZ/0.25Vrmsasthestandardorequivalentinstrument

One、Planestructurediagram：(Tolerance±1)Unit:MM J=Lengthcanbeadjustedaccordingtodemands. A 25±0.5 B 2.5±0.2 C 23.7±0.2 D 21±0.5 E 13.5±0.2 F 2.3±0.2Height ofcentercolumn H 7.7±0.1 I 2.0±0.1 J 7±1 K 7.8x2.0±0.05 Two、ProductSpecs： Pin-OutWireDiameterTurnsRemark S--F0.08*24P11 热风绞合线 Three、Technicalrequirements：(Themagneticforceofthemagnetis2800gauss) 1.Fixthethreadtopreventlooseandbrokenwires. 2.Accordingtocustomer’srequirements,thelongwireendswillbecutandtinned, andthetinningdepthis2±1MM. 3．Dotappropriatewhiteglueonthesoftmagneticsheetandattachthecoil. Duringtheprocess,makesurethesurfaceoftheproductiscleanandtidy. 4.Thesoftmagneticsheetusedhasroundholesandisnotdamaged. Additionalprocess(accordingtocustomer’srequirements):Installa7.8x2.0mm magnetinthemiddleholeofthefinishedproductandablackfilmclosetothesize ofthemagnetisaffixedtothebackofthefinishedproducts. Four、Electricalparameter: 1.Inductanceparameter，Qparameter： PINS—F=5.4uH±0.2UH Magnet Qparameter≥28 TheaboveinductanceparameterarebasedonQuanhua1062Ainstrument,with 10KHZ/0.3Vrmsasthestandardorequivalentinstrument. TheQparameterisbasedonQuanhua1062Ainstrument,using100KHZ/0.3Vrmsas thestandardorequivalentinstrument

ProjectNo.:ZKT-2309046913E Page 1 of 27 FCCTESTREPORT FCCID:2BCT5-581007 ReportNumber. .................................. :ZKT-2309046913E DateofTest ....................................................... : Sept.04,2023toSept.12,2023 Dateofissue.........................................: Sept.12,2023 Totalnumberofpages..........................27 TestResult .......................................... : PASS TestingLaboratory............................: ShenzhenZKTTechnologyCo.,Ltd. Address ............................................... : 1/F,No.101,BuildingB,No.6,TangweiCommunityIndustrial Avenue,FuhaiStreet,Bao'anDistrict,Shenzhen,China Applicant'sname.............................: DongguanYOUElectronicTechnologyCo.,Ltd Address...............................................: Room201,Building1,No.2,ShengqiangangNo.3street,Huangjiang Town,DongguanCity,GuangdongProvince,China Manufacturer'sname......................: DongguanYOUElectronicTechnologyCo.,Ltd Address ............................................... : Room201,Building1,No.2,ShengqiangangNo.3street,Huangjiang Town,DongguanCity,GuangdongProvince,China Testspecification: Standard................................................:FCCCFRTitle47Part15SubpartC Testprocedure ..................................... : / Non-standardtestmethod................:N/A TestReportFormNo. ....................... : TRF-EL-107_V0 TestReportForm(s)Originator ..... : ZKTTesting MasterTRF ........................................ : Dated:2020-01-06 ThisdevicedescribedabovehasbeentestedbyZKT,andthetestresultsshowthattheequipmentunder test(EUT)isincompliancewiththeFCCrequirements.Anditisapplicableonlytothetestedsample identifiedinthereport. Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofZKT,thisdocumentmay bealteredorrevisedbyZKT,personalonly,andshallbenotedintherevisionofthedocument. Productname ..................................... : 2in1Wirelesscharger Trademark...........................................: N/A Model/Typereference.........................: 581007 YWC-65 Ratings..................................................: Input:5V1A,5V2A AirpodsWirelessOutput:5W(Max) AppleWatchMagneticChargerOutput:2.5W(Max) ProjectNo.:ZKT-2309046913E Page 2 of 27 Testingprocedureandtestinglocation: TestingLaboratory.......................................:ShenzhenZKTTechnologyCo.,Ltd. Address............................................................:1/F,No.101,BuildingB,No.6,TangweiCommunity IndustrialAvenue,FuhaiStreet,Bao'anDistrict, Shenzhen,China TomZou Testedby(name+signature).......................: JacksonFang Reviewer(name+signature).......................: LakeXie Approved(name+signature) ....................... : ProjectNo.:ZKT-2309046913E Page 3 of 27 TABLEOFCONTENTS 1.VERSION.......................................................................................................................................4 2.TESTSUMMARY........................................................................................................................5 2.1TESTFACILITY....................................................................................................................................6 2.2MEASUREMENTUNCERTAINTY....................................................................................................6 3.GENERALINFORMATION......................................................................................................7 3.1GENERALDESCRIPTIONOFEUT..................................................................................................7 3.2Testmode..............................................................................................................................................7 3.3BlockDiagramofEUTConfiguration................................................................................................8 3.4TestConditions.....................................................................................................................................8 3.5DescriptionOfSupportUnits(ConductedMode)............................................................................8 3.6EQUIPMENTSLISTFORALLTESTITEMS..................................................................................9 4.CONDUCTEDEMISSIONTEST..............................................................................................9 4.1CONDUCTEDEMISSIONMEASUREMENT................................................................................11 4.1.1POWERLINECONDUCTEDEMISSIONLimits........................................................................11 4.1.2TESTPROCEDURE.......................................................................................................................11 4.1.3DEVIATIONFROMTESTSTANDARD.......................................................................................11 4.1.4TESTSETUP...................................................................................................................................12 4.1.5EUTOPERATINGCONDITIONS.................................................................................................12 4.1.6TestResult.......................................................................................................................................12 5.RADIATEDEMISSIONMEASUREMENT............................................................................13 5.1RadiatedEmissionLimits..................................................................................................................13 5.2AnechoicChamberTestSetupDiagram........................................................................................14 5.3TestProcedure....................................................................................................................................14 5.4DEVIATIONFROMTESTSTANDARD..........................................................................................14 5.5TestResult.....................................................…

Text truncated - open the document above for the full version.

EUTTESTPHOTO