2BCUQ-W610DPortable DECT Phone

Portable DECT Phone Quick Start Guide V1.0 W610D Packing list Handset Belt Clip Quick Start Guide Portable dect Phone Rechargeable Battery Power Adapter Charging Base Earpiece Status Indicator Speaker Belt clamping hole Headphone jack PTT key Menu key Phone book Keypad Microphone Charging interface On-hook key/PowerOff-hook key Mute key Hands-free Soft key Screen Volume Key + Volume Key - Navigation key OK key Install the battery 1. Remove the rear case: Remove the rear case of the whole machine with a little force from the handle position A of the rear case of the main unit. 2. Install the battery: Take out the battery from the packaging box, with the battery with the notch facing up, put the battery C at the battery compartment C. 3. Install the battery cover: Align the back cover with the buckle on the back of the main unit, press your hands along the edge of the main unit from top to bottom (there will be a "click" sound during the process), and ensure that there is no gap, it means that the back cover is fastened. Replacement battery 1. Remove the rear case: Remove the rear case of the whole machine with a little force from the handle position A of the rear case of the main unit. Remove the rear case Install the battery Install the back cover CC Buckle A 2. Remove the old battery: Push up at B to remove the old battery. 3. Install the new battery: Take out the battery from the packaging box, with the battery with the notch facing up, put the battery C at the battery compartment C. Connect the charging base Remove the rear case Remove the battery A Install the back cover Buckle C Install the battery 4. Install the back cover: Align the back cover with the buckle on the back of the main unit, press your hands along the edge of the main unit from top to bottom (there will be a "click" sound during the process), and ensure that there is no gap, it means that the back cover is fastened. C B Language setting 1.Press Menu key > Basic > Language. 2.Select the desired language and press OK softkey. Note 1.Use original factory supplied power adapter (5V/2A). A third-party power adapter may damage the handset. 2.Check the charging status on the top-right corner of the LCD screen. Connecting W610D to the Network To use the communication function of W610D, the device must first be connected to the network. The specific steps are as follows: 1.The system administrator needs to first enter the IPUI address of the device into the system on the paired Manager and authorize the device to access. Install the belt clip 2.Terminal connects the network 2.1 Boot up the W610D device and select the the corresponding country, access Menu > WLAN > Available Networks. Select the Manager's RFPI , click "Connect," and enter the password to establish a successful connection. 2.3 After a successful connection, the terminal automatically obtains configuration settings (SIP account and internal extension) and can perform call operations. 3-party conference 1.Once in line with 1st caller, press softkey-More > Conference, 1st caller is put on hold. 2.Then call the 2nd number. After, 2nd call is established, press softkey-More > Conference to set up the conference. Country/Region setting 1.Press Menu key > Network> Country/Region. 2.Select the desired area and press OK softkey. Note that the Country/Region of W610D and Base must be consistent so that W610D can search and connect to Base. Accepting a call 1.With the handset: press the Off-Hook key. 2.With a headset: when the headphone inserted, press the Off-Hook key. 3.With the handsfree: press Handfree key. Putting a call on hold 1.Press the softkey-More > Hold, caller is put on hold. 2.To retrieve the call press the softkey-More > Resume. Note: with more than one active call, select desired call with the navigator keys and use the corresponding softkey to hold or resume. Making a call 1.Pre-dialing: enter the phone number and press Handfree/Off-Hook/Softkey-Dial key. 2.Direct dialing: press Handfree/Off-Hook key and enter the phone number, then press “#”/Handfree/Off-Hook key to call out the number. 3.Headset: Insert headphones, enter the number, and press the off hook button. 4.Designated line: press Handfree/Off-Hook key, or enter the phone number directly, then press Navigation Key-Up key to select line. Call forward 1.Press Menu > Features > Call Forward. 2.Select the line, the type of forward, enter the destination number and status and press OK. Call Mute 1.Long Press”*” key to Mute the microphone during the call. 2.Long Press”*” key again to un-mute the conversation. Phonebook Call list 1.Press Navigation keys - Up or Menu > Call Log > Local Call Logs. 2.Scroll through the list using navigation keys 3.To dial an entry, press Softkey- Option > Dial or Handfree/Off-Hook key. Call transfer Attended transfer: 1.Press softkey-More > Xfer during the active conversation, the call is put on hold. 2.Dial the second telephone number. 3.When the call is answered, then press softkey-More > Xfer to complete the operation. Blind transfer: 1.Press softkey-More > Xfer during the active conversation, the call will be on hold. 2.Then enter the 2nd telephone number and press softkey-More > Xfer. Access phonebook: 1.Press Physical buttons > PhoneBook or Menu > PhoneBook > Local Contacts. 2.Select All Contacts or other group. 3.To dial an entry, press Softkey- Option > Dial or Handfree/Off-Hook key. Add new entry: 1.Press Menu > PhoneBook > Local Contacts, Press All Contacts or other group > Press Add. 2.Enter name and number and press OK soft key. Programmable keys DSSkey Press Navigation keys - Left or Navigation keys -Right, select among the configurable items, and select your desired type and value, press OK key. Redial Press Handfree/Off-Hook key and then press Softkey-Redial. Do not disturb 1.Press Menu > Features > DND. 2.Select the Mode, and press OK soft key. Voice message 1.To access your voice mailbox, press Menu > Message > Voice Message, number of messages will be ind…

Text truncated - open the document above for the full version.

FanvilLinkTechnologyCo.,LTD A03,A08,3rdFloor,Building2,DaqianIndustrialPlant,Zone67,XingdongCommunity,Xin'anStreet, Bao'anDistrict,Shenzhen,China FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Date:Jun.14,2024 Ref:AttestationStatementsPart2.911(d)(5)(i)Filing FCCID:2BCUQ-W610D FRN:0034227223 [FanvilLinkTechnologyCo.,LTD](“theapplicant”)certifiesthattheequipmentforwhichauthorizationis soughtisnot“covered”equipmentprohibitedfromreceivinganequipmentauthorizationpursuantto section2.903oftheFCCrules. Sincerely, (Applicantsignature) (mengjiaoHu)

FanvilLinkTechnologyCo.,LTD A03,A08,3rdFloor,Building2,DaqianIndustrialPlant,Zone67,XingdongCommunity,Xin'an Street,Bao'anDistrict,Shenzhen,China FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Date:Jun.14,2024 Ref:AttestationStatementsPart2.911(d)(5)(ii)Filing FCCID:2BCUQ-W610D FRN:0034227223 [FanvilLinkTechnologyCo.,LTD](“theapplicant”)certifiesthat,asofthedateofthefilingofthe application,theapplicantisnotidentifiedontheCoveredListasanentityproducing“covered” equipment. Sincerely, (Applicantsignature) (mengjiaoHu)

FanvilLinkTechnologyCo.,LTD A03,A08,3rdFloor,Building2,DaqianIndustrialPlant,Zone67,XingdongCommunity,Xin'anStreet,Bao'an District,Shenzhen,China 2.911(d)(7)USAAgentv1.2 Section2.911(d)(7)USAAgentforServiceofProcess FCCID:2BCUQ-W610D 2.911(d)(7)USADesignatedAgentforServiceofProcess We,[FanvilLinkTechnologyCo.,LTD](“theapplicant”)designate[EMCTEK] NOTE1 forthepurposeofacceptingserviceofprocessonbehalfof theapplicant. Applicantconsent:WeAcknowledgeourconsenttoacceptserviceofprocessintheUnitedStatesformattersrelatedtotheapplicable equipment,andatthephysicalU.S.addressandemailaddressofthedesignatedagentandacknowledgeouracceptanceofourobligationto maintainanagentforserviceofprocessintheUnitedStatesfornolessthanoneyearaftereitherthegranteehaspermanentlyterminatedall marketingandimportationoftheapplicableequipmentwithintheU.S.,ortheconclusionofanyCommission-relatedadministrativeorjudicial proceedinginvolvingtheequipment,whicheverislater. Agentobligation:WeAcknowledgeourobligationtoacceptserviceofprocessintheUnitedStatesformattersrelatedtotheapplicable equipmentatourphysicalU.S.addressandemailaddressfornolessthanoneyearaftereitherthegranteehaspermanentlyterminatedall marketingandimportationoftheapplicableequipmentwithintheU.S.,ortheconclusionofanyCommission-relatedadministrativeorjudicial proceedinginvolvingtheequipment,whicheverislater. USAAgent Companyname:EMCTEK Address:11788BigCanyonLn,SanDiegoCA92131USA FRN:00334018291 ContactName:FangLiu TelephoneNo:/ Email:[email protected] Applicant Companyname:FanvilLinkTechnologyCo.,LTD Address:A03,A08,3rdFloor,Building2,DaqianIndustrialPlant,Zone 67,XingdongCommunity,Xin'anStreet,Bao'anDistrict,Shenzhen, China FRN：0034227223 ContactName:MengjiaoHu TelephoneNo:15089240223 Email:[email protected] Signature: Date:2024.06.22Date:2024.06.22 NOTE1:AnapplicantlocatedintheUnitedStatesmaydesignateitselfastheagentforserviceofprocess. Reference;FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-communications-supply-c hain-through-the

Fanvil Link Technology Co., LTD A03, A08, 3rd Floor, Building 2, Dagian IndustralPlant, Zone 67, Xingdong Community, Xin'anStreet, Bao'an District, Shenzhen , China Jun. 14, 2024 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Explanation of differences between product types FCC ID: 2BCUQ-W610D Models: W610D, W610DP, W710P, W610P To Whom It May Concern: We, The Fanvil Link Technology Co., LTD hereby declare that the model : W610D is identical with the model : W610DP, W710P, W610P, only the model names are different Sincerely, Fanvil Link Technology Co., LTD Signature: [mengjiao Hu, General Manager]

FanvilLinkTechnologyCo.,LTD A03,A08,3rdFloor,Building2,DaqianIndustrialPlant,Zone67,XingdongCommunity, Xin'anStreet,Bao'anDistrict,Shenzhen,China OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date:Jun.14,2024 Subject;RequestforConfidentiality FCCID:2BCUQ-W610D ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram OperationalDescription PartsList Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely, Signature: Name:mengjiaoHu Title:GeneralManager

Fanvil Link Technology Co., LTD A03, A08, 3rd Floor, Building 2, Dagian IndustralPlant, Zone 67, Xingdong Community, Xin'anStreet, Bao'an District, Shenzhen , China (Jun. 14, 2024) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize (Attestation of Global Compliance (Shenzhen) Co., Ltd) to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Name: mengjiao Hu Title: General Manager

Report No.: AGC14499240405AP03 Page 1 of 4 EXTERNAL PHOTOS WHOLE VIEW OF EUT TOP VIEW OF EUT Adapter 2#: F12L20-050200SPAU Adapter 1#: GQ12-050200-AU Report No.: AGC14499240405AP03 Page 2 of 4 BOTTOM VIEW OF EUT FRONT VIEW OF EUT Report No.: AGC14499240405AP03 Page 3 of 4 BACK VIEW OF EUT LEFT VIEW OF EUT Report No.: AGC14499240405AP03 Page 4 of 4 RIGHT VIEW OF EUT ****************************************End of Report*************************************

FCC ID Label Location 20mm*30mm FCC ID: 2BCUQ-W610D

Report No.: AGC14499240405AP03 Page 1 of 9 INTERNAL PHOTOS OPEN VIEW-1 OF EUT OPEN VIEW-2 OF EUT BT Antenna Report No.: AGC14499240405AP03 Page 2 of 9 BATTERY OF EUT OPEN VIEW-3 OF EUT Report No.: AGC14499240405AP03 Page 3 of 9 OPEN VIEW-4 OF EUT DECT ANTENNA DECT Antenna Report No.: AGC14499240405AP03 Page 4 of 9 BLUETOOTH ANTENNA INTERNAL VIEW-1 OF EUT Report No.: AGC14499240405AP03 Page 5 of 9 INTERNAL VIEW-2 OF EUT SCREEN PRINTING Report No.: AGC14499240405AP03 Page 6 of 9 INTERNAL VIEW-3 OF EUT INTERNAL VIEW-4 OF EUT Report No.: AGC14499240405AP03 Page 7 of 9 INTERNAL VIEW-5 OF EUT INTERNAL VIEW-6 OF EUT Report No.: AGC14499240405AP03 Page 8 of 9 INTERNAL VIEW-7 OF EUT INTERNAL VIEW-8 OF EUT Report No.: AGC14499240405AP03 Page 9 of 9 INTERNAL VIEW-9 OF EUT INTERNAL VIEW-10 OF EUT ****************************************End of Report*************************************

CALIBRATION DATA PROBE CALIBRATION DATA DIPOLE CALIBRATION DATA

Page 1 of 43 SAR Test Report Report No.: AGC14499240405FH01 FCC ID : 2BCUQ-W610D APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Portable DECT Phone BRAND NAME : MODEL NAME : W610D, W610DP, W710P, W610P APPLICANT : Fanvil Link Technology Co., LTD DATE OF ISSUE : Jun. 13, 2024 STANDARD(S) : IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2005 REPORT VERSION : V1.0 Attestation of Global Compliance(Shenzhen) Co., Ltd. Report No.: AGC14499240405FH01 Page 2 of 43 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jun. 13, 2024 Valid Initial Release Report No.: AGC14499240405FH01 Page 3 of 43 Test Report Applicant Name Fanvil Link Technology Co., LTD Applicant Address A03, A08, 3rd Floor, Building 2, Daqian Industrial Plant, Zone 67, Xingdong Community, Xin'an Street, Bao'an District, Shenzhen, China Manufacturer Name Fanvil Link Technology Co., LTD Manufacturer Address A03, A08, 3rd Floor, Building 2, Daqian Industrial Plant, Zone 67, Xingdong Community, Xin'an Street, Bao'an District, Shenzhen, China Factory Name N/A Factory Address N/A Product Designation Portable DECT Phone Brand Name Model Name W610D Series Models W610DP, W710P, W610P Declaration of Difference Only the model names are different EUT Voltage DC 3.8V by battery Applicable Standard IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2005 Date of receipt of test item May 06, 2024 Test Date Jun. 03, 2024 Report Template AGCRT-US-1.8G/SAR (2021-04-20) Note: The results of testing in this report apply to the product/system which was tested only. Prepared By Jack Gui(Project Engineer) Jun. 13, 2024 Reviewed By Calvin Liu (Reviewer) Jun. 13, 2024 Approved By Max Zhang (Authorized Officer) Jun. 13, 2024 Report No.: AGC14499240405FH01 Page 4 of 43 TABLE OF CONTENTS 1. SUMMARY OF MAXIMUM SAR VALUE ......................................................................................................... 5 2. GENERAL INFORMATION ............................................................................................................................... 6 2.1. EUT DESCRIPTION......................................................................................................................................... 6 3. SAR MEASUREMENT SYSTEM ........................................................................................................................ 7 3.1. THE SATIMO SYSTEM USED FOR PERFORMING COMPLIANCE TESTS CONSISTS OF FOLLOWING ITEMS .................. 7 3.2. COMOSAR E-FIELD PROBE .......................................................................................................................... 8 3.3. ROBOT .......................................................................................................................................................... 8 3.4. VIDEO POSITIONING SYSTEM .......................................................................................................................... 9 3.5. DEVICE HOLDER ............................................................................................................................................ 9 3.6. SAM TWIN PHANTOM ................................................................................................................................... 10 4. SAR MEASUREMENT PROCEDURE .............................................................................................................. 11 4.1. SPECIFIC ABSORPTION RATE (SAR) .............................................................................................................. 11 4.2. SAR MEASUREMENT PROCEDURE ................................................................................................................ 12 4.3. RF EXPOSURE CONDITIONS ......................................................................................................................... 14 5. TISSUE SIMULATING LIQUID ......................................................................................................................... 15 5.1. THE COMPOSITION OF THE TISSUE SIMULATING LIQUID..................................................................................... 15 5.2. TISSUE DIELECTRIC PARAMETERS FOR HEAD AND BODY PHANTOMS ............................................................... 15 5.3. TISSUE CALIBRATION RESULT ....................................................................................................................... 16 6. SAR SYSTEM CHECK PROCEDURE ........................................................................................................... 17 6.1. SAR SYSTEM CHECK PROCEDURES ............................................................................................................. 17 6.2. SAR SYSTEM CHECK ................................................................................................................................... 18 7. EUT TEST POSITION ...................................................................................................................................... 19 7.1. DEFINE TWO IMAGINARY LINES ON THE HANDSET ........................................................................................... 19 7.2. CHEEK POSITION ......................................................................................................................................... 20 7.3. TILT POSITION .............................................................................................................................................. 20 7.4. BODY WORN POSITION ................................................................................................................................ 21 8. SAR EXPOSURE LIMITS ............................................................................................................................... 22 9. TEST FACILITY ........................................................................................................…

Text truncated - open the document above for the full version.

东莞市一佳电子通讯科技有限公司 Dongguan YiJia Electronics Communication Technology Co.,Ltd. 规格承认书 SPECIFICATION FOR APPROVAL 2023/08/31 日期 Date 编号 File No 版本 230831002 Revision 1.0 客户 CUSTOMER: 方位 客户料号 CUSTOMER NO: EAEA100005A0 品名 DECTAntenna 品名 DECT PART NAME: Antenna 供方料号 SUPPLIER NO: YJL01.106.054.301A 送样数量Q“ 送样日期 Date: TY: 客户确认CUSTOMER APPROVED BY APPROVALCHIEFSUPERVISOR 供方确认SUPPLIER SIGNATURE APPROVALCHECKDESIGN APPROVALCHECKDESIGN ChenGuoqiangXieLiChenXingyi YJ-RD-F04-A 承认书项目表 NO . 内容 （Contents） 页数 （Number of Page） 页码 （Page Code） 1 承认书S封面（pec Cover） 11 承认书封面（p） 2 承认书项目表（Spec Item ） 12 3 工程成品图（Drawing） 13 4 天线规格（Antenna Specification） 14 5 S参数测试（S Parameter ） 15 6 无源测试（Passive Test ） 26 ~ 7 7 方向图（Radiation Pattern ） 28 ~ 9 8 天线装配图（Antenna Profile） 310 ~ 12 9 材质证明（Mt ilC tifi t） 251337 9 MaterialCertificate 材质证明（） 2513 ~ 37 10 RoHS报告（RoHS Test Report ） **** 11N/AN/AN/A add：东莞市长安镇沙头社区木鱼路59号元富工业区 Yuanfu Industrial Zone, No.59, Muyu Road, Shatou Community, Changan Town, Dongguan City Tel:0769-82586086 Fax:0769-82586086 12--- 13--- 天线规格 Antenna Specification Electrical Properties Frequency 1780-1940MHz qy Impedance50 Ohm Nominal V.S.W.R2.0 Max Gain 46dBi Gain 4.6dBi RadiationOmni-directional PolarizationLinear Physical Properties ConnectorNone Cable TypeNone Cable LengthNone Cable ColorNone Operating Temp.-40 ~ +85 ̊C Storage Temp / Humidity 25±5 ̊C / <70% Agilent Agilent E5071B SS Parameter Test // DECT Antenna Antenna Passive Test AntennaPassiveTe s t Z Y X X Z Y Passive Test For DECT Antenna Freq (MHz) Effi (%) Effi (dB) Gain (dBi) 1780 51.1-2.92.9 1790 49.8-3.03.2 1800 50.4-3.03.4 1810 51 1293751. 1810 1-2.93.7 1820 51.5-2.93.9 1830 51.4-2.93.9 1840 50.7-3.03.9 1850 52.2-2.84.0 1860 52.2-2.83.9 1870 53.7-2.74.1 1880 51 8-2941 1880 51.82.94.1 1890 52.6-2.84.3 1900 52.4-2.84.6 1910 53.1-2.84.6 1920 54.6 4. -2.6 6 1930 54.1-2.74.2 1940 52.0-2.84.0 Radiation Pattern For DECT Antenna 1780MHz 1940MHz Phi 0° Phi 90° Theta90° eta90 DeviceDevice DECT Antenna Material safety data (MSDS) 1、 Item and manufacturer information page: 1 / 2 Item name: FPC antenna electroplated nickel and gold (flexible printed circuit) Other names: FPC nickel gold coating Recommended use and restricted use: communication products Name of manufacturer or supplier: Dongguan Xiaoge Electronic Technology Co., Ltd Address of manufacturer or supplier: 1 / 2 / F, Sanxing Road, Fenghuang Middle Road, Shajiao community, Humen Town, Dongguan City Emergency contact / Fax: 2、 Hazard identification data Hazard classification: other dangerous substances, acute toxic substances, grade 4 (swallowing, skin, inhalation) Label content: Symbols: other dangerous objects, exclamation marks Warning: warning Hazard warning message: harmful if swallowed, harmful if inhaled Hazard prevention measures: put the container in a well ventilated place; avoid contact with skin and eyes; in case of accide nt or discomfort, consult medical treatment immediately Other hazards:- 3、 Component identification data mixture Chinese and English Name: nickel CAS no.7440-02-0 percentage 98.95% Gold CAS no.7440-57-5 percentage 1% Brightener CAS no.6155-57-3 percentage 0.05% Synonymous Name: gold finger nickel gold layer Case No Composition of hazardous substances (percentage of components) 4、 First aid measures First aid methods for different exposure routes: Inhalation: - irritates respiratory tract Skin contact: wash the contact area with soap and water Eye contact: flush with plenty of water for more than 15 minutes and seek medical assistance Ingestion: drink plenty of water and seek medical assistance The most important symptom and harmful effect: irritant. Protection of first-aid personnel: wear class C protective equipment to implement first aid in safe area Tips for doctors: patients should be given oxygen when inhaled.When swallowing, consider gastric lavage. 5、 Fire fighting measures Suitable extinguishing agent: Carbon dioxide, chemical powder, water mist, alcohol foam. Special hazards that may be encountered during fire fighting: When heated to dry, the salt will decompose to produce carbon monoxide and carbon dioxide. Special fire fighting procedures: 1.Spray water mist to cool containers exposed to fire.2. Spray water to wash away the leakage to avoid exposure. Special protective equipment for fire fighters: If necessary, wear a full body chemical protective respirator 6、 Physical and chemical properties page: 2 / 2 State of mattercoloursmellproportionmelting pointboiling point NI solid statesilvery whitetasteless 8.9 1453Temperature2732Temperature AU solid stateyellowtasteless 19.3 1064Temperature2807Temperature Brightenerliquid stateLight browntasteless 1.1NANA 7、Safe handling and storage methods management: Avoid contact with eyes, skin and clothing, wear personal protective equipment and do not inhale mist Storage: Store in a cool, dry place 8、 Waste disposal methods Waste disposal method: 1.According to the current laws and regulations. 2.According to the manufacturer's treatment, the waste to be treated should be treated first 3.In accordance with the relevant national and local government industrial wastewater discharge standards 9、 Leakage treatment method Personal precautions: wear appropriate personal protective equipment. Environmental precautions: ventilate the leakage area. Cleaning method: dilute with a large amount of clean water, and wash and discharge to the ditch. 10、 Exposure precautions Engineering control: 1. Local exhaust device; 2. Overall air exchange device; 3. The ventilation system should be made of corrosion-resistant materials and separated from other exhaust systems. Control parameters Eight hour daily average Allowable concentration TWA Short time volume average Allowable concentration STEL Maximum permissible concentration CEILING Biological indicators BEIs 1mg/m32mg/m3-- Personal protective equipment: Respiratory protection:- Hand protection: impervious gloves made of natural rubber, butyl rubber and polyvinyl alcohol. Eye protec…

Text truncated - open the document above for the full version.

Page 1 of 71 FCC Test Report Report No.: AGC14499240405FR01 FCC ID : 2BCUQ-W610D APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Portable DECT Phone BRAND NAME : MODEL NAME : W610D, W610DP, W710P, W610P APPLICANT : Fanvil Link Technology Co., LTD DATE OF ISSUE : Jun. 14, 2024 STANDARD(S) : FCC Part 15 Subpart D §15.323 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC14499240405FR01 Page 2 of 71 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jun. 14, 2024 Valid Initial Release Report No.: AGC14499240405FR01 Page 3 of 71 Table of Contents 1. General Information ........................................................................................................................................ 5 2. Product Information ........................................................................................................................................ 6 2.1 Product Technical Description ................................................................................................................... 6 2.2 Test Frequency List ................................................................................................................................... 6 2.3 Related Submittal(S) / Grant (S) ............................................................................................................... 7 2.4 Test Methodology ...................................................................................................................................... 7 2.5 Automatic Discontinuation of Transmission .............................................................................................. 7 2.6 Digital Modulation Techniques .................................................................................................................. 8 2.7 Special Accessories .................................................................................................................................. 8 2.8 Equipment Modifications ........................................................................................................................... 8 2.9 Antenna Requirement................................................................................................................................ 8 3. Test Environment ............................................................................................................................................ 9 3.1 Address of The Test Laboratory ................................................................................................................ 9 3.2 Test Facility ................................................................................................................................................ 9 3.3 Environmental Conditions ....................................................................................................................... 10 3.4 Measurement Uncertainty ....................................................................................................................... 10 3.5 List of Equipment Used ........................................................................................................................... 11 4.System Test Configuration ............................................................................................................................ 13 4.1 EUT Configuration ................................................................................................................................... 13 4.2 EUT Exercise ........................................................................................................................................... 13 4.3 Configuration of Tested System .............................................................................................................. 13 4.4 Equipment Used in Tested System ......................................................................................................... 14 4.5 S…

Text truncated - open the document above for the full version.