2BCYL-DNS-010CXMicrowave Radar Module

Radar Module Model No. : DNS-010CX X-Band Microwave Motion SensorModule ■ Features - X-Band Radar Motion Sensor Module(Small Type) - * Used a RF the Microwave Sensor. * The up-to-date sense which uses Dopplerprinciple. * Low cost & Low PowerConsumption. *Very Small Size(28.2* 18.7*10mm) and FlatProfile. * Reliable Construction & High Sensitivity. ■ Outline Drawing ■ Interface 1 : 5V 2 : GND 3 : IF ■ Specification (Model No.:DNS-010CX) (Transmitter) Frequency : 10.525GHz. Frequency Setting Accuracy :3MHz Power Output (Min.) : 5dBmEIRP Operating Voltage : +5V±0.3V(Option : +3.3V±0.3V) Operating Current (CW) : 20mA~25mA typical Harmon ic Emissions : <-30dBm (Pulse Mode Operation) Average Current (5% DC) : 1 mAtyp. Pulse Width (Min.) : 5 micro Sec Dut y Cycle (Min.) :1% (Receiver) Sensitivity (10dB S/N ratio) in 3Hz to 80Hz bandwidth : TDBdBm Noise in 3Hz to 80Hz bandwidth : TDB microV Antenna Gain:8dBi E Plane 3dB Beamwidth : 50°.H Plane 3dB Beamwidth : 60°. (Module Characteristics) Operating Temperature Range : -15'C to+55'C Storage Temperature Range : -30'C to+70'C Detection Range : 7M ~ 8M(Wall Type). 5M Diameter(Ceiling Type). Weight : 6 grams. Size(mm,+/-0.2) : 28.2 * 18.7 *10 FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Validity of using the module certification: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. In such cases, please involve a FCC certification specialist in order to determine if a Permissive Class II Change or new Certification is required. Upgrade Firmware: The software provided for firmware upgrade will not be capable to affect any RF parameters as certified for the FCC for this module, in order to prevent compliance issues. End product labeling: This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2BCYL-DNS-010CX”. Information that must be placed in the end user manual: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. WARNING Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. “CAUTION : Exposure to Radio Frequency Radiation. Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit. Information that must be placed in the end user manual: Requirement per KDB996369 D03 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.10 below concerning the need to notify host manufacturers that further testing is required.3 Explanation: This module meets the requirements of FCC part 15C(15.245). 2.3 Summarize the specific operational use conditions Describe use conditions that are applicable to the modular transmitter, including for example any limits on antennas, etc. For example, if point-to-point antennas are used that require reduction in power or compensation for cable loss, then this information must be in the instructions. If the use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual. In addition, certain information may also be needed, such as peak gain per frequency band and minimum gain, specifically for master devices in 5 GHz DFS bands. Explanation: Antenna Gain: 0 dBi, There are no specific operational use conditions. The EUT has a PCB Antenna, and the antenna use a permanently attached antenna which is not replaceable. 2.4 Limited module procedures If a modular transmitter is approved as a “limited module,” then the module manufacturer is responsible for approving the host environment that the limited module is used with. The manufacturer of a limited module must describe, both in the filing and in the installation instructions, the alternative means that the limited module manufacturer uses to verify that the host meets the necessary requirements to satisfy the module limiting conditions. A limited module manufacturer has the flexibility to define its alternative method to address the conditions that limit the initial approval, such as: shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation. The alternative method could include that the limited module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval. This limited module procedure is also applicable for RF exposure evaluation when it is necessary to demonstrate compliance in a specific host. The module manufacturer must state h…

Text truncated - open the document above for the full version.

Dnet. Co., Ltd 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – Equipment Type Company name: Dnet. Co., Ltd Address: 23, Hosan-ro 2-gil, Dalseogu, Daegu, South Korea Product Name: Microwave Radar Module FCC ID: 2BCYL-DNS-010CX Model(s): DNS-010CX 2.911(d)(5)(i) Equipment Type We, Dnet. Co., Ltd (“the applicant”) certify that the equipment for which authorization is sought through certification is not: • Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules. • Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: SeongJeong Park Date: September 25, 2023 Title and Company name: CEO / Dnet. Co., Ltd NOTE 1 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Dnet. Co., Ltd 2.911 (d)(5)(ii) Applicant Attestation v1.3 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: Dnet. Co., Ltd Address: 23, Hosan-ro 2-gil, Dalseogu, Daegu, South Korea Product Name: Microwave Radar Module FCC ID: 2BCYL-DNS-010CX Model(s): DNS-010CX 2.911(d)(5)(ii) Applicant filing We, Dnet. Co., Ltd (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 , established pursuant to § 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name: SeongJeong Park Date: September 25, 2023 Title and Company name: CEO / Dnet. Co., Ltd NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Dnet.co.Ltd 23, Hosan-ro 2-gil, Dalseo-gu, Daegu, South Korea Date: September 22, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BCYL-DNS-010CX US Agent – Attestation Statement / Part 2.911(d)(7) Dnet.co.Ltd certifies, that as of September 22, 2023, we have designated FCC US Agent, LLC to accept service of process on our behalf for FCC ID: 2BCYL-DNS-010CX Dnet.co.Ltd, accepts to maintain an agent of service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. FCC US Agent, LLC, accepts as of the date of the filing of this application, the obligation of being the designated agent for the purpose of accepting service of process on behalf of Dnet.co.Ltd for FCC ID: 2BCYL-DNS-010CX Designated Agent Information: Company Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708-571-3148 Email: [email protected] Sincerely, Company: Dnet.co.Ltd Designated Agent: FCC US Agent, LLC Company Representative: SeongJeong, Park Designated Agent Representative: Tim Payne Signature: Signature:

Letter of Authorization Company: Dnet. Co., Ltd Address: 23, Hosan-ro 2-gil, Dalseogu, Daegu, South Korea Product Name: Microwave Radar Module Model Number: DNS-010CX FCC Identifier: 2BCYL-DNS-010CX We authorize MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: SeongJeong Park Date: September 25, 2023 Title: CEO Signature of applicant:

Dnet. Co., Ltd FCC Modular Approval Request Rev 3.0 Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: September 25, 2023 Subject; Modular Transmitter Application Company name: Dnet. Co., Ltd FCC ID: 2BCYL-DNS-010CX Dear Sir/Madam, This letter includes the FCC application requirements for Modular Transmitter Approval Request for;- FCC KDB 996369 D01 ‘Module Certification Guide v02; and FCC KDB 996369 D03 OEM Manual v01 In accordance with 47CFR 15.212 Modular Transmitters and KDB 996369 D01 ‘Module Equip Auth Guide v02’. FCC ID 2BCYL-DNS-010CX has been examined against the following requirements. Requirement per 15.212 and KDB 996369 D01 Explanation from Grantee (do not write yes/no, but explain why product complies/how it is achieved) The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly. Yes The radio portion of the module has been shielded, Refer to the external photos. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal. Yes The module has buffered modulation/data inputs. Refer to the Block Diagram. The module must contain power supply regulation on the module. Yes This module is equipped internal power regulators. Refer to the Block Diagram. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per §§ 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b). Yes This module is equipped with an onboard Chip Antenna. Refer to the internal photo The module must demonstrate compliance in a stand-alone configuration. Yes This module was tested in a stand-alone configuration. Refer to the test setup photos The module must be labeled with its permanently affixed FCC ID label, or use an electronic display (see KDB Publication 784748). Yes The module has its permanently affixed FCC ID label and the FCC ID label is shield cover. Refer to the FCC ID Label Location. The module must comply with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. Yes The module complies with all specific rules applicable to the transmitter. The module must comply with RF exposure requirements Yes Refer to the EMF Test Report. Dnet. Co., Ltd FCC Modular Approval Request Rev 3.0 Integration Instructions for host product manufacturers The following items are submitted in support of application for Modular Transmitter FCC ID as noted above as required by the FCC KDB 996369 D03 OEM Manual v01. These items are provided as integration instructions for host product manufacturers (e.g., OEM instruction manual) to use when integrating a module in a host product. Any requirements that are not applicable to the Module are as indicated below. Summary of requirements and Checklist. Refer to the KDB for description of the complete requirements; KDB Ref Sect Requirements of KDB 996369 D03 User Manual Page Number reference 2.2 List of applicable FCC rules 6 Page 2.3 Summarize the specific operational use conditions 6 Page 2.4 Limited module procedures 6 Page 2.5 Trace antenna designs 7 Page 2.6 RF exposure considerations 7 Page 2.7 Antennas 7 Page 2.8 Label and compliance information 8 Page 2.9 Information on test modes and additional testing requirements 8 Page 2.10 Additional testing, Part 15 Subpart B disclaimer 8 Page Name: SeongJeong Park Date: September 25, 2023 Title: CEO Signature of applicant

Dnet. Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: September 25, 2023 Subject; Request for Confidentiality FCC ID: 2BCYL-DNS-010CX To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: SeongJeong Park Title: CEO

Page 1 of 2 FCC ID: 2BCYL-DNS-010CX Page 2 of 2 FCC ID: 2BCYL-DNS-010CX

IDENTIFICATION LABEL PROPOSED FCC ID LABEL The FCC ID shall be permanently affixed in the rear of the equipment DNS-010CX MODEL : DNS-010CX FCC ID : 2BCYL-DNS-010CX Power source : DC 5V Manufacturer : Dnet. Co., Ltd

Page 1 of 3 FCC ID: 2BCYL-DNS-010CX Page 2 of 3 FCC ID: 2BCYL-DNS-010CX Page 3 of 3 FCC ID: 2BCYL-DNS-010CX PCB Antenna

Page 1 of 7 Report No.: OT-239-RWD-032 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMF TEST REPORT Test Report No. : OT-239-RWD-032 Reception No. : 2308002557 Applicant : Dnet. Co., Ltd Address : 23, Hosan-ro 2-gil, Dalseogu, Daegu, South Korea Manufacturer : Dnet. Co., Ltd Address : 23, Hosan-ro 2-gil, Dalseogu, Daegu, South Korea Type of Equipment : Microwave Radar Module FCC ID : 2BCYL-DNS-010CX Model Name : DNS-010CX Multiple Model Name : N/A Serial number : N/A Total page of Report : 7 pages (including this page) Date of Incoming : August 07, 2023 Date of Issuing : September 25, 2023 SUMMARY The equipment complies with the regulation; FCC CFR 47 PART 2.1091 This test report contains only the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. This report is not correlated with the "KS Q ISO/IEC 17025 and KOLAS accreditation" of Korean Laboratory Accreditation Scheme. Tested by Si-eon Lee / Sr. Engineer ONETECH Corp. Reviewed by Tae-Ho, Kim / Chief Engineer ONETECH Corp. Approved by Jae-Ho, Lee / Chief Engineer ONETECH Corp. Page 2 of 7 Report No.: OT-239-RWD-032 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) CONTENTS Page 1. VERIFICATION OF COMPLIANCE ............................................................................................................................. 4 2. GENERAL INFORMATION ............................................................................................................................................ 5 2.1 PRODUCT DESCRIPTION ................................................................................................................................................. 5 2.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT. ................................................................ 5 3. EUT MODIFICATIONS .................................................................................................................................................... 5 4. MAXIMUM PERMISSIBLE EXPOSURE ...................................................................................................................... 6 4.1 RF EXPOSURE CALCULATION ....................................................................................................................................... 6 4.2 EUT DESCRIPTION ......................................................................................................................................................... 6 4.3 CALCULATED MPE SAFE DISTANCE............................................................................................................................. 7 Page 3 of 7 Report No.: OT-239-RWD-032 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) Revision History Rev. No. Issue Report No. Issued Date Revisions Section Affected 0 OT-239-RWD-032 September 25, 2023 Initial Release All Page 4 of 7 Report No.: OT-239-RWD-032 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) 1. VERIFICATION OF COMPLIANCE Applicant : Dnet. Co., Ltd Address : 23, Hosan-ro 2-gil, Dalseogu, Daegu, South Korea Contact Person : Jung ChulHwan / Director Telephone No. : +82-53-584-3545 FCC ID : 2BCYL-DNS-010CX Model Name : DNS-010CX Brand Name : - Serial Number : N/A Date : September 25, 2023 DEVICE TYPE FDS - Part 15 Field Disturbance Sensor E.U.T. DESCRIPTION Microwave Radar Module THIS REPORT CONCERNS Original Grant MEASUREMENT PROCEDURES KDB 447498 D01 General RF Exposure Guidance v06 TYPE OF EQUIPMENT TESTED Pre-Production KIND OF EQUIPMENT AUTHORIZATION REQUESTED Certification MODIFICATIONS ON THE EQUIPMENT TO ACHIEVE COMPLIANCE None -. The above equipment was tested by ONETECH Corp. for compliance with the requirement set forth in the FCC Rules and Regulations. This said equipment in the configuration described in this report, shows the maximum emission levels emanating from equipment are within the compliance requirements. Page 5 of 7 Report No.: OT-239-RWD-032 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) 2. GENERAL INFORMATION 2.1 Product Description The Dnet. Co., Ltd, Model DNS-010CX (referred to as the EUT in this report) is an Microwave Radar Module, Product specification information described herein was obtained from product data sheet or user’s manual. DEVICE TYPE Microwave Radar Module OPERATING FREQUENCY 10.525 GHz Field Strength of Fundamental 106.61 dBμV/m ANTENNA TYPE PCB Antenna ANTENNA GAIN 0 dBi 2.2 Alternative type(s)/model(s); also covered by this test report. -. None. 3. EUT MODIFICATIONS -. None Page 6 of 7 Report No.: OT-239-RWD-032 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) 4. MAXIMUM PERMISSIBLE EXPOSURE 4.1 RF Exposure Calculation According to the FCC rule 1.1310 table 1B, the limit for the maximum permissible RF exposure for an uncontrolled en…

Text truncated - open the document above for the full version.

Radar Module Model No. : DNS-010CX X-Band Microwave Motion SensorModule ■ Features - X-Band Radar Motion Sensor Module(Small Type) - * Used a RF the Microwave Sensor. * The up-to-date sense which uses Dopplerprinciple. * Low cost & Low PowerConsumption. *Very Small Size(28.2* 18.7*10mm) and FlatProfile. * Reliable Construction & High Sensitivity. ■ Outline Drawing ■ Interface 1 : 5V 2 : GND 3 : IF ■ Specification (Model No.:DNS-010CX) (Transmitter) Frequency : 10.525GHz. Frequency Setting Accuracy :3MHz Power Output (Min.) : 5dBmEIRP Operating Voltage : +5V±0.3V(Option : +3.3V±0.3V) Operating Current (CW) : 20mA~25mA typical Harmon ic Emissions : <-30dBm (Pulse Mode Operation) Average Current (5% DC) : 1 mAtyp. Pulse Width (Min.) : 5 micro Sec Dut y Cycle (Min.) :1% (Receiver) Sensitivity (10dB S/N ratio) in 3Hz to 80Hz bandwidth : TDBdBm Noise in 3Hz to 80Hz bandwidth : TDB microV AntennaGain:0dBi E Plane 3dB Beamwidth : 50°.H Plane 3dB Beamwidth : 60°. (Module Characteristics) Operating Temperature Range : -15'C to+55'C Storage Temperature Range : -30'C to+70'C Detection Range : 7M ~ 8M(Wall Type). 5M Diameter(Ceiling Type). Weight : 6 grams. Size(mm,+/-0.2) : 28.2 * 18.7 *10 Radar Module ■ Antenna Pattern (DNS-010CX) ■ Applications 1. security relation products (sensor and alarm set etc). 2. Home Automation 3. automobile rear collision warning. 4. automatic door sensor. 5. sensor light. 6. sensors it applies in all products which operate. ■ Summary of Microwave Motion SensorModule 1. Microwave Motion Sensor Module is developed applying Doppler Radar principle. 2. The role of Sensor Module is transmitting a low power Microwave from transmitting antenna and receiving the microwave energy reflected by objects to receiving antenna. 3. If the movement of the object is detected by the microwave motion sensor, the reflected microwave frequency is shifted away from the transmit frequency to receiving antenna. 4. The reflected and shifted microwave frequency is mixed with the transmit microwave frequency and results a low frequency voltage at the output of the sensor. 5. The Microwave Motion Sensor Module is designed with Dielectric Resonator Oscillator(DRO).

Page 1 of 23 Report No.: OT-239-RWD-031 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) RADIO PERFORMANCE TEST REPORT Test Report No. : OT-239-RWD-031 Reception No. : 2308002557 Applicant : Dnet. Co., Ltd Address : 23, Hosan-ro 2-gil, Dalseogu, Daegu, South Korea Manufacturer : Dnet. Co., Ltd Address : 23, Hosan-ro 2-gil, Dalseogu, Daegu, South Korea Type of Equipment : Microwave Radar Module FCC ID : 2BCYL-DNS-010CX Model Name : DNS-010CX Multiple Model Name : N/A Serial number : N/A Total page of Report : 23 pages (including this page) Date of Incoming : August 07, 2023 Date of Issuing : September 25, 2023 SUMMARY The equipment complies with the requirements of FCC CFR 47 PART 15 SUBPART C Section 15.245 This test report contains only the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. This report is not correlated with the "KS Q ISO/IEC 17025 and KOLAS accreditation" of Korean Laboratory Accreditation Scheme. Tested by Si-eon Lee / Sr. Engineer ONETECH Corp. Reviewed by Tae-Ho, Kim / Chief Engineer ONETECH Corp. Approved by Jae-Ho, Lee / Chief Engineer ONETECH Corp. Page 2 of 23 Report No.: OT-239-RWD-031 It should not be reproduced except in full, without the written approval of ONETECH Corp. OTC-TRF-RF-001(0) ONETECH Corp.: 43-14, Jinsaegol-gil, Chowol-eup, Gwangju-si, Gyeonggi-do, 12735, Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) CONTENTS Page 1. VERIFICATION OF COMPLIANCE ............................................................................................................................. 5 2. TEST SUMMARY .............................................................................................................................................................. 6 2.1 TEST ITEMS AND RESULTS ............................................................................................................................................. 6 2.2 RELATED SUBMITTAL(S) / GRANT(S) ............................................................................................................................ 6 2.3 PURPOSE OF THE TEST ................................................................................................................................................... 6 2.4 TEST METHODOLOGY .................................................................................................................................................... 6 2.5 TEST FACILITY ............................................................................................................................................................... 6 3. GENERAL INFORMATION ............................................................................................................................................ 7 3.1 PRODUCT DESCRIPTION ................................................................................................................................................. 7 3.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT. ................................................................ 7 4. EUT MODIFICATIONS .................................................................................................................................................... 7 5. SYSTEM TEST CONFIGURATION ............................................................................................................................... 7 5.1 JUSTIFICATION ............................................................................................................................................................... 7 5.2 PERIPHERAL EQUIPMENT .............................................................................................................................................. 7 5.3 MODE OF OPERATION DURING THE TEST ...................................................................................................................... 8 5.4 CONFIGURATION OF TEST SYSTEM ............................................................................................................................... 9 5.5 ANTENNA REQUIREMENT .............................................................................................................................................. 9 6. PRELIMINARY TEST ...................................................................................................................................................... 9 6.1 AC POWER LINE CONDUCTED EMISSIONS TESTS ......................................................................................................... 9 6.2 RADIATED EMISSIONS TESTS......................................................................................................................................... 9 7. MINIMUM 20 DB BANDWIDTH .................................................................................................................................. 10 7.…

Text truncated - open the document above for the full version.