2BDVY-C06CHECKER PRINT WIRELESS CHARGING PAD/DAISY SMILEY WIRELESS CHARGING PAD

Form: RFT-AMER-TCB-OP-19o Revision: 1 Page 1 of 1 Date: 1/25/2023 [NINGBO QTOP IMP&EXP CO., LTD.] Attention: Application Examiner Re: Certification designating a U.S. agent for service of process pursuant to section 2.911(d)(7) of the FCC rules To whom it may concern, This letter is to confirm both [QTOP USA INC.] (“Agent”) and [NINGBO QTOP IMP&EXP CO., LTD.] (“Applicant”) acknowledge consent to obligations of each party pursuant to 47 CFR part §2.911(d)(7) of the FCC rules in regard to the agent for service of process. I [Belle Lai] HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant. I further acknowledge the requirement to maintain an agent extends for no less than one year after the termination of all marketing and importation or the conclusion of and commission-related proceeding involving the equipment and agree to immediately notify the FCC and Intertek if there is any change in the status identified above. Applicant Company Name : NINGBO QTOP IMP&EXP CO., LTD. Contact Name : Belle Lai Address : 17/F,Romon Plaza,No.575 Tiantongnan Road, Yinzhou District,Ningbo,China Telephone No : 0086-0574-89219746 Email : [email protected] FCC ID : 2BDVY-C06 Applicant FRN : 0034558320 Signature: Date: 1/2/2024 I [ Erin M Lockard] HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Agent. I consent to the obligation to accept service of process on behalf of the applicant in regard to the FCC ID designated above. Agent Company Name : QTOP USA INC. Contact Name : Erin M Lockard Address : 12225 SOUTH ST STE 100 ARTESIA, CA 90701 Telephone No : 001-214-280 3050 Email : [email protected] Agent FRN : 0034671503 Signature: Date: 1/2/2024

NINGBO QTOP IMP&EXP CO.,LTD. Attention: Application Examiner Re: Covered List, located at https://www.fcc.gov/supplychain/coveredlist and 47 CFR parts §2.903 and §2.911(d)(5)(ii) of the FCC rules Applicant: NINGBO QTOP IMP&EXP CO.,LTD. FCC ID: 2BDVY-C06 To Whom It May Concern, NINGBO QTOP IMP&EXP CO.,LTD.(“Applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to 47 CFR part §2.903 of the FCC rules and does not originate directly or indirectly from any company named on the covered list located in the link above or any subsidiary or affiliate thereof. Applicant further certifies that, as of the date of the filing of the application, the Applicant is not identified on the Covered List as an entity producing “covered” equipment and is not a subsidiary or affiliate of any such entity pursuant to 47 CFR part §1.50002 and required by 47 CFR part §2.911(d)(5)(ii) of the FCC rules. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant and agree to immediately notify Intertek if there is any change in the status identified above. _ Belle Lai QE NINGBO QTOP IMP&EXP CO.,LTD. 2023.12.28

(NINGBO QTOP IMP&EXP CO.,LTD.) Date:2023.12.26 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement (NINGBO QTOP IMP&EXP CO., LTD.) FCC ID: 2BDVY-C06 To Whom It May Concern: We, NINGBO QTOP IMP&EXP CO., LTD., hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number 2BDVY-C06 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is 2023.12.26. The Limited Agency Agreement expires on 2024.12.26, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, [Signature] Belle Lai QE

1(2) NINGBO QTOP IMP&EXP CO.,LTD. Attention: Certification reviewer RE: Request for Confidentiality FCC ID: 2BDVY-C06 To Whom It May Concern: Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: [Select one or more of items below, as appropriate] Schematics Block Diagrams Operational Description Tune-up Procedure Parts List Internal Photos (see note) Users Manual (see note) Note 1: Internal Photos may be held confidential 1) if the circuit board or internal components are not accessible to users. For example, it is acceptable if the circuit board is enclosed in epoxy. 2) Also, it is acceptable if the device is not accessible to the public, for example, a device mounted on the top of a large tower (or in a fenced enclosure) such that it is only serviceable by professional designated technicians under a Non-Disclosure Agreement (NDA). All sales for these devices must be under a NDA restricting the disclosure of the propriety information, including internal photos. Users Manual may be held confidential only when the manual contains proprietary technical information intended for professional technicians obligated under a NDA. All sales and distribution of the user’s manual must be under a NDA that restricts the disclosure of the information. In the application cover letter requesting permanent confidentiality the following additional description and the NDA exhibit is required: 1. Describe in detail how internal photos and/or users manual information are controlled to prevent them from becoming public or disclosed to unauthorized persons. 2. Describe how public access is restricted for products serviceable by professional designated technicians. 3. A statement that all sales of the non-consumer device will be under a NDA to include third party sales and that the final user of the device is subject to the NDA. 4. Provide an example of the NDA between the grantee and a purchaser. The request for confidentiality must Note 2: For scanning receiver, the schematics, block diagrams, operational description, tune-up procedure, parts list and internal photos are always held permanently confidential. Short-term Confidentiality [Complete this section if short-term confidentiality is requested] Request to withhold from public review for a period of [90] days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept short-term confidential for a period above from the date of the grant [Select one or more of items below that are not selected in the list above, as appropriate] Schematics Block diagrams Operational Description Tune-up Procedure 2(2) Parts List Test Setup Photos External Photos Internal Photos Users Manual Rationale for request for confidentiality: We have invested considerable time and materials in research and development to produce the referenced product. Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. Short-term confidentiality: Disclosure of the short-term confidential portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development. If you have questions or need further information, please contact the undersigned. Sincerely, Belle Lai QE 2023.12.28

The label is at the bottom of the product

NINGBO QTOP IMP&EXP CO.,LTD TEST REPORT SCOPE OF WORK SAR Assessment– C06 REPORT NUMBER 231205049SZN-002 ISSUE DATE [REVISED DATE] 08 March 2024 [--------------------] PAGES 5 DOCUMENT CONTROL NUMBER RF Exposure © 2017 INTERTEK TEST REPORT Intertek No.: 231205049SZN-002 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page 1 of 5 RF Exposure 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 www.intertek.com Test Report Applicant : NINGBO QTOP IMP&EXP CO.,LTD 17F,Romon Plaza,No.575 Tiantongnan Road, YinzhouDistrict,Ningbo,China Sample Description Product : CHECKER PRINT WIRELESS CHARGING PAD/DAISY SMILEY WIRELESS CHARGING PAD Model No. : C06 Electrical Rating : Input: 5V/2A, 9V/2A Wireless Output: 5W, 7.5W, 10W, 15W Date Received : 05 December 2023 Date Test Conducted : 05 December 2023 to 21 February 2024 Test Requested : Test for compliance with CFR 47 part 1 Test Method : Environmental evaluation and exposure limit according to FCC CFR 47 part 1, 1.1307(c) and (d), 1.1310 KDB 680106 D01 RF Exposure Wireless Charging v04 Test Result : Pass Conclusion : When determining of test conclusion, measurement uncertainty of tests have been considered. ******************************** End of Page ******************************** Prepared and Checked By: Approved By: Holland Yang Ryan Chen Engineer Sr. Project Engineer Date: 08 March 2024 TEST REPORT Intertek No.: 231205049SZN-002 Version: 01-November-2017 Page 2 of 5 RF Exposure Test Report Test Setup Configuration Note: - The RF exposure test is performed in the shield room. - The test distance is measured from the center of the test probe along all three axes of the device, from 0 cm to 20 cm, from the edge of the device coil in minimum 2 cm increments. TEST REPORT Intertek No.: 231205049SZN-002 Version: 01-November-2017 Page 3 of 5 RF Exposure Test Equipment List Equipment No. Equipment Manufacturer Model No. Cal. Date Due Date SZ186-06 The Magnetic Ampli tude and Gradient Probe System SPEAG MAGPy- 8D3D+E3D 2023-04-13 2024-04-13 This product was tested in the following configuration: Description Manufacturer Detail Mobile phone Apple (Provided by Intertek) Model: iPhone 14(A2884) Adapter NIL (Provided by Intertek) Model: AC-250K Input: 100-240Vac 50/60Hz 0.55A Output: 5Vdc 2A, 9Vdc 2A Justification The EUT was powered by an adapter with 120V/60Hz input during the test. All power input voltages (DC 5V⎓2A, 9V⎓2A) and all rated output powers have been tested. And have considered all the following EUT modes of operation to pre-scan the test system. Pertest mode Description Mode 1 Standby mode Mode 2 Mobile phone is charging at 1% battery power Mode 3 Mobile phone is charging at 50% battery power Mode 4 Mobile phone is charging at 99% battery power Mode 5 Continuous maximum power Note: 1. H-field data are measured in minimal increments of 2 cm from the edge of the device along all three axes of the device, from 0 cm to 20 cm, one axis is consistent with the axis of the main coil, all modes and distances have been fully tested. The worst-case testing data were recorded in this report. 2. Mode 5 is a special product sample provided by the customer for this test, which allows the equipment to operate at maximum power without a client device. TEST REPORT Intertek No.: 231205049SZN-002 Version: 01-November-2017 Page 4 of 5 RF Exposure Reference Limit: Environmental evaluation and exposure limit according to FCC CFR 47 part 1, 1.1307(c) and (d), 1.1310 According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation. LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range ( MHz ) Electric Field strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A) Limits for Occupational/Controlled Exposure 0.3 – 3.0 614 1.63 (100) * 6 (B) Limits for General Population/Uncontrolled Exposure 0.3 – 1.34 614 1.63 (100) * 30 Note: * = Plane wave equivalent power density Test Result: During test, the mobile phone is being charged. Worst Case Operating Mode: Mode 5 for 2cm distance; Mode 2 for 4cm to 20cm distance Center of the probe to the probe outer edge is 1.85 cm, so the test distance can only reach 2cm. H-field strength measurement result at 2cm to 20 cm: Test Position Test distance(cm) Limits (A/m) 2 4 6 8 10 12 14 16 18 20 Side 1 1.075 0.378 0.086 0.049 0.025 0.022 0.017 0.014 0.011 0.008 1.63 Side 2 1.041 0.361 0.084 0.053 0.027 0.021 0.017 0.013 0.009 0.006 1.63 Side 3 1.013 0.365 0.085 0.052 0.024 0.021 0.016 0.013 0.010 0.007 1.63 Side 4 1.036 0.376 0.081 0.051 0.026 0.022 0.018 0.012 0.010 0.008 1.63 Top 1.077 0.387 0.087 0.054 0.029 0.023 0.019 0.015 0.011 0.009 1.63 TEST REPORT Intertek No.: 231205049SZN-002 Version:…

Text truncated - open the document above for the full version.

NINGBO QTOP IMP&EXP CO., LTD TEST REPORT SCOPE OF WORK FCC TESTING–C06 REPORT NUMBER 231205049SZN-001 ISSUE DATE [REVISED DATE] 08 March 2024 [---------------------] PAGES 20 DOCUMENT CONTROL NUMBER FCC ID 209_b © 2017 INTERTEK Intertek Report No.: 231205049SZN-001 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page: 1 of 20 FCC ID 209_b TEST REPORT 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 www.intertek.com NINGBO QTOP IMP&EXP CO., LTD Application For Certification FCC ID: 2BDVY-C06 CHECKER PRINT WIRELESS CHARGING PAD/DAISY SMILEY WIRELESS CHARGING PAD Model: C06 Transmitter Report No.: 231205049SZN-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-22] Prepared and Checked by: Approved by: Holland Yang Ryan Chen Engineer Sr. Project Engineer Date: 08 March 2024 Intertek Report No.: 231205049SZN-001 Version: 01-November-2017 Page: 2 of 20 FCC ID 209_b TEST REPORT MEASUREMENT/TECHNICAL REPORT This report concerns (check one) Original Grant X Class II Change Equipment Type: DCD - Part 15 Low Power Transmitter Below 1705 kHz Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until : date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator - the new 47 CFR [10-01- 22] Edition] provision. Report prepared by: Holland Yang Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen. Tel: (86 755) 8614 0743 Fax: (86 755) 8601 6751 Intertek Report No.: 231205049SZN-001 Version: 01-November-2017 Page: 3 of 20 FCC ID 209_b TEST REPORT Table of Contents 1.0 Summary of Test Results .......................................................................................... 4 2.0 General Description ................................................................................................. 5 2.1 Product Description .............................................................................................. 5 2.2 Related Submittal(s) Grants ................................................................................... 5 2.3 Test Methodology ................................................................................................ 5 2.4 Test Facility ......................................................................................................... 5 3.0 System Test Configuration ........................................................................................ 6 3.1 Justification ......................................................................................................... 6 3.2 EUT Exercising Software ........................................................................................ 6 3.3 Special Accessories ............................................................................................... 6 3.4 Equipment Modification ........................................................................................ 6 3.5 Measurement Uncertainty .................................................................................... 7 3.6 Support Equipment List and Description ................................................................ 7 4.0 Measurement Results .............................................................................................. 8 4.1 Field Strength Calculation ...................................................................................... 8 4.2 Radiated Emission Configuration Photograph ........................................................... 9 4.3 Radiated Spurious Emission ................................................................................... 9 4.4 Conducted Emission Configuration Photograph ...................................................... 13 4.5 Conducted Emission ........................................................................................... 13 5.0 Equipment Photographs ........................................................................................ 16 6.0 Product Labelling .................................................................................................. 16 7.0 Technical Specifications ......................................................................................... 16 8.0 Instruction Manual ................................................................................................ 16 9.0 Miscellaneous Information .........................................................................…

Text truncated - open the document above for the full version.