2BDZK-F9DVR

FCC ID LABEL: Ca. 20mm x 10mm Label Location FCC ID: 2BDZK-F9

MPE ESTIMATION FCC ID: 2BDZK-F9 1, According to §1.1310, Limit for General Population/ Uncontrolled Exposures Frequency Power density (mW/ cm 2 ) Averaging time(minutes) 300MHz----1.5GHz F/1500 30 1.5GHz---100GHz 1.0 30 Note: F= Frequency in MHz 2, Estimation Result For WIFI: Mode Max PK Output power(dBm) Tune Up Power(dBm) Max Tune Up power(mW) Antenna Gain(dBi) Antenna Gain (Numerical) MPE (mW/cm²) 5755 8.27 8±1(9) 7.94 2.62 1.83 0.00289 Note: Note: The estimation distance is 20cm Note: PK Output power= conducted power in mW. G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna in cm Conducted power see the test report HK2510115588-E, antenna gain=2.62dBi when the minimum test separation distance is >20 cm, a distance of 20 cm is applied to determine RF Exposure test exclusion. The test exclusion threshold is 0.00289 which is< 1.0, RF Exposure testing is not required. -------The End-------

1 /6 1. Application 2.4GHz 5 221 Chip Antenna: RANT5221F550M02 s WLAN ,80 2.11 b/g, Bl uetoot h , WLAN ,etc ... 2. F eatu r es S MD , hi g hr e li ab ili ty,u l t r a Im pact,O mni- d ir ect i o n a l... 3. PartNumberInformation RANT5221F02 (A)(B)(C) 550 (D)(F M (E)) (A)Produc t Ty p eChi p An t enna (B)SizeCode 5 .1x2.0mm (±0 .2mm ) (C)MaterialHighKmaterial (D)Frequency5.15 ~ 5.85GHz (E)FeedingmodePIFA& S ingl e F eed ing (F)AntennatypeType=02 咏成國際科技有限公司 RAINInternationalTechnologyCo.,Ltd. 2/ 6 4. 00 2.3000 4.产品尺寸 5020单极天线 5.ElectricalSpecification Specification PartNumber RANT5221F245M02 CentralFrequency MH5.15 ~ 5.85GHzz Bandwidth120(Min.) MHz ReturnLoss -10(Max) dB PeakGaindB 2.62 i Impedance 50Ohm OperatingTemperature - 40～+85 °C MaximumPower4W ResistancetoSolderingHeats 10(@260°C) sec. PolarizationLinear AzimuthBeamwidth Omni-directional TerminationSn(Leadless) 6. 推荐PCB FootPrint(Unit:mm) W Figure SymbolDimension(mm) L W A L（长） 5.10±0.20 W（宽） 2.00±0.30 T（厚度） 1.0±0.30 A （电极宽度） 0.50±0.20 4.0 3 /6 RecommendedPCBPattern EvaluationBoardDimension LayoutDimensionsinClearancearea (Size=7.0*5.0mm) 50ohmtransmissionLine MatchingCircuit 4 /6 7.MeasurementResults ReturnLoss 7.2RadiationPattern 5 /6 260 °C 20-40s 217°C 150-200°C Pre-heating 60-150s 60-180s Time(s) 8.ReliabilityandTestCondictions Testitem Testcondition/Testmethod Specification Solderability JISC0050-4.6 JESD22-B102D *Solderbathtemperature：2355C *Immersiontime：20.5sec Solder：Sn3Ag0.5Cuforlead-free Atleast95%ofasurfaceofeachterminal electrodemustbecoveredbyfreshsolder. Leaching (Resistanceto dissolutionof metallization) IEC60068-2-58 *Solderbathtemperature：2605C *Leachingimmersiontime：30 0.5sec Solder:SN63A Lossofmetallizationontheedgesofeach electrodeshallnotexceed25%. Bendingtest JISC0051-7.4.1 Themiddlepartofsubstrateshallbe pressurizedbymeansofthepressurizingrod atarateofabout1mm/sperseconduntilthe deflectionbecomes1mm/sandthenpressure shallbemaintainedfor51sec. Measurementtobemadeafterkeepingat roomtemperaturefor242hours Nomechanicaldamage. Electricalspecificationshallsatisfythe descriptionsinelectricalcharacteristicsunder theoperationaltemperaturerangewithin-40 ~85°C. Resistancetosoldering heat JISC0050-5.4 *Preheatingtemperature：120~150 °C , 1minute. *Soldertemperature：2705C *Immersiontime：101sec Solder：Sn3Ag0.5Cuforlead-free Measurementtobemadeafterkeepingat roomtemperaturefor242hrs Nomechanicaldamage. Electricalspecificationshallsatisfythe descriptionsinelectricalcharacteristicsunder theoperationaltemperaturerangewithin-40 ~85°C. Lossofmetallizationontheedgesofeach electrodeshallnotexceed25%. 9.SolderingandMounting T e m p e r a t u r e ( ° C ) 11.StorageandTransportationInformatio 6 /6 n StorageConditions Tomaintainthesolderabilityofterminalelectrodes: 1.Temperatureandhumidityconditions:-10~40 °C and30~70%RH. 2.Recommendedproductsshouldbeusedwithin6monthsfromthetimeof delivery. 3.Thepackagingmaterialshouldbekeptwherenochlorineorsulfurexists intheair. TransportationConditions 1.Productsshouldbehandledwithcaretoavoiddamageorcontamination fromperspirationandskinoils. 2.Theuseoftweezersorvacuumpickupisstronglyrecommendedfor individualcomponents. 3.Bulkhandlingshouldensurethatabrasionandmechanicalshockare minimized. (1) Quantity/Reel: 2000 pcs/Reel 10.Packing (2) Plastic tape: b. Tape Dimensions (unit: mm)a. Tape Drawing FeatureSpecificationsTolerances W12.00±0.30 P4.00±0.10 E1.75±0.10 F 5.50±0.10 P2 ±0.102.00 +0.10 -0.00 D Po 1.50 4.00±0.10 ±0.2010Po40.00

Page 1 of 59 Report No.: HK2510115588-E FCC Test Report Test Report On Behalf of Shenzhen Fisang Electronics Co., Ltd. For DVR Model No.: F9, X1, X2, X3, X4, X5, X6, X7, X8, X9, X10, X11, X12, X13, X14, X15 FCC ID: 2BDZK-F9 Prepared For: Shenzhen Fisang Electronics Co., Ltd. 5th Floor, Building B6, Xujingchang Industrial Park, No.39 Haoye Road, Zhancheng Community, Fuhai Street, Bao’an District, Shenzhen, China Prepared By: Shenzhen HUAK Testing Technology Co., Ltd. 1-2/F., Building B2, Junfeng Zhongcheng Zhizao Innovation Park, Heping, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Date of Test: Oct. 11, 2025 ~ Nov. 17, 2025 Date of Report: Nov. 17, 2025 Report Number: HK2510115588-E Page 2 of 59 Report No.: HK2510115588-E Test Result Certification Applicant’s Name ................. : Shenzhen Fisang Electronics Co., Ltd. Address .................................. : 5th Floor, Building B6, Xujingchang Industrial Park, No.39 Haoye Road, Zhancheng Community, Fuhai Street, Bao’an District, Shenzhen, China Manufacturer's Name ........... : Shenzhen Fisang Electronics Co., Ltd. Address .................................. : 5th Floor, Building B6, Xujingchang Industrial Park, No.39 Haoye Road, Zhancheng Community, Fuhai Street, Bao’an District, Shenzhen, China Product Description Trade Mark ............................. : N/A Product Name ........................ : DVR Model and/or Type Reference : F9, X1, X2, X3, X4, X5, X6, X7, X8, X9, X10, X11, X12, X13, X14, X15 Standards .............................. : FCC Rules and Regulations Part 15 Subpart E Section 15.407 ANSI C63.10: 2020 This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen HUAK Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen HUAK Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Date of Test ........................................... : Date (s) of performance of tests ............. : Oct. 11, 2025 ~ Nov. 17, 2025 Date of Issue .......................................... : Nov. 17, 2025 Test Result .............................................. : Pass Testing Engineer Len Liao Technical Manager Sliver Wan Authorized Signatory Jason Zhou Page 3 of 59 Report No.: HK2510115588-E Table of Contents 1. Summary ................................................................................................... 5 1.1 Test Procedures and Results ........................................................................................................... 5 1.2 Information of the Test Laboratory ................................................................................................. 5 1.3 Measurement Uncertainty ................................................................................................................ 6 2. EUT Description ........................................................................................ 7 2.1 General Description of EUT ............................................................................................................. 7 2.2 Operation Frequency Each of Channel ........................................................................................... 8 2.3 Operation of EUT during Testing ..................................................................................................... 8 2.4 Description of Test Setup ................................................................................................................. 9 2.5 Description of Support Units ......................................................................................................... 10 3. General Information ................................................................................ 11 3.1 Test Environment and Mode .......................................................................................................... 11 4. Test Results and Measurement Data .................................................... 13 4.1 AC Conducted Emission ................................................................................................................ 13 4.2 Maximum Conducted Output Power ............................................................................................. 17 4.3 6dB Emission Bandwidth ............................................................................................................... 20 4.4 26dB Bandwidth and 99% Occupied Bandwidth ......................................................................... 25 4.5 Power Spectral Density .................................................................................................................. 26 4.6 Band Edge ........................................................................................................................................ 31 4.7 Spurious Emission .......................................................................................................................... 40 4.8 Frequency Stability Measurement ................................................................................................. 53 4.9 Antenna Requirement ..................................................................................................................... 56 5. Test Setup Photos of the EUT ............................................................... 57 6. Photos of the EUT ................................................................................... 59 Page 4 of 59 Report No.: HK2510115588-E ** Modified History ** Revision Description Issued Date Remark Revision 1.0 Initial Test Report Release Nov. 17, 2025 Jason Zhou Page 5 of 59 Report No.: HK2510115588-E 1. Summary 1.1 Test Procedures and Results Requirement CFR 47 Section Result Antenna Requirement §15.203 PASS AC Power Line Conducted Emission §15.207 PASS Maximum C…

Text truncated - open the document above for the full version.

Test Model: F9 Radiated Emission AC Conducted Emission RF Conducted Emission