2BE29-MSV02Sous Vide Cooker

USER MANUAL SOUS VIDE MSV02 The most obvious benefit of sous vide cooking is that you can prepare perfectly cooked food every time you step into the kitchen — all with very little effort. No more overcooked fish, rubbery chicken, or chewy steak. 01 WHAT IS SOUS VIDE? Developed in France in the 1970s, sous vide is a culinary technique to cook the vacuum-sealed food in a water pot, by a consistent low temperature for a long period of time. It is an easy cooking with simple steps: just season and vacuum seal the food; clamp the sous vide to the water & setup it; slip the food into the water pot. That's it all. With sous vide cooking temperature and cooking time are precisely controlled so as to avoid the overcooking. To use the vacuum sealed bags that are used fluid cannot escape; meat particularly cooks in its own juices and hardly loses any weight. Food prepared in this manner retains its full flavor. BENEFITS OF SOUS VIDE COOKING But that's not the only reason to cook sous vide. The gentle, oxygen-free cooking environment helps to retain your foods' valuable nutrients. Plus, foods cooked in a vacuum-sealed bag are far more shelf stable than those cooked on the stove top — this means you can cook countless meals ahead of time without worrying about your dinner spoiling. Another benefit? When cooking sous vide, proteins like chicken and pork can be served at lower temperatures than when following traditional cooking methods. The increased minimum cook time for the sous vide cooking process essentially pasteurizes the meat, which means that medium-rare pork chops and subtly pink chicken are perfectly safe to eat. Even better — sous vide cooking is truly a “set it and forget it” method of cooking. Seal your food, place it in your water pot, and walk away. Since the water pot will never get above the desired temperature, the food will never exceed your preferred level of doneness. Throw dinner parties with ease — that juicy ribeye or pork tenderloin can be made hours ahead of time and finished right before serving, leaving you plenty of time to socialize with your guests. IMPORTANT SAFEGUARDS 02 SAVE THESE INSTRUCTION When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against electrical shock do not immerse cord, plugs in water or other liquid. DO NOT FILL WATER OVER MAX LINE. 4. Close supervision is necessary when any appliance is used by or near children. 5. Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts. 6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair, or adjustment. 7. The use of accessory attachments not recommended by the appliance manufacturer may cause injuries. 8. Do not use outdoors, household use only. 9. Do not let cord hang over edge of table or counter, or touch hot surfaces. 10. Do not place on or near a hot gas or electric burner, or in a heated oven. 11. Extreme caution must be used when moving an appliance containing hot oil or other hot liquids. 12. Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control to “off”, then remove plug from wall outlet. 13. Do not use appliance for other than intended use. HOUSEHOLD USE ONLY IMPORTANT SAFEGUARDS 1. This appliance can be used by persons with reduced physical, sensory capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. 2. Children shall not use the appliance. Cleaning and user maintenance shall not be made by children without supervision. 3. The appliance is not intended to be operated by means of an external timer or separate remote-control system. 4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 5. Before connecting the device to power, please confirm that the local voltage is in conformity with the voltage instruction at the bottom part of the device. 6. Please do not plug or unplug the power cord with wet hands. 7. Please do not use the appliance when the power cord or plug is lose or damaged. 8. Please do not attempt to repair or modify a defective power cord by yourself. Contact a service center to replace the power cord by qualified electrician. 9. To protect against electric shock, do not immerse the whole unit, power cord or plug in water or other liquids. 10. This appliance is intended to be used in household and similar application such as: -staff kitchen areas in shops, offices and other working environment; -farm houses; -by clients in hotels, motels and other residential type environment; -bed and breakfast type environment; 11. The instructions for appliances normally cleaned after use, and not intended to be immersed in water for cleaning, shall unplug the immersion heater before moving it from the liquid. 12. When the appliance is not in use and before cleaning, unplug the appliance from the outlet firstly. 13. The use of attachments which are not recommended or sold by the appliance manufacturer may cause a risk of injury to persons. 14. The appliance is only intended for the purpose described in user manual. Do not use the appliance or any part of appliance out of the intended use to avoid risk. Always keep basic safety precautions when operating electrical appliances, including the following: CAUTION 03 IMPORTANT SAFEGUARDS 1. This appliance can be used by persons with reduced physical, sensory capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the h…

Text truncated - open the document above for the full version.

Applicant:GuangzhouMophomIndustrialCo.,Ltd Address:No.206Commercial,No.2,HuijingWestSecondStreet,HuaduDistrict,Guangzhou, Guangdong,China Tel:+8602086972867 Email:[email protected] AttestationLetter Date:2024-05-17 FEDERALCOMMUNICATIONSCOMMISSIONS AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 Ref:AttestationStatementsCFR4782.911(d)(5)i)Filing FCCID:2BE29-MSV02 GuangzhouMophomIndustrialCo.,Ltdcertifiesthattheequipmentforwhichauthorizationis sought,įsnot"coveredequipmentprohibitedfromreceivinganequipmentauthorization pursuanttosection2.903oftheFCCrules. Sincerely, Signature OwenChong Manager QwenChng CFR47$2.911(dX5)Xi)AttestationLetter

Applicant:GuangzhouMophomIndustrialCo.,Ltd Address:No.206Commercial,No.2,HuijingWestSecondStreet,HuaduDistrict,Guangzhou, Guangdong,China Tel:+8602086972867 Email:[email protected] Date:2024-05-17 FEDERALCOMMUNICATIONSCOMMISSIONS AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 Ref:AttestationStatementsCFR47$2.911(d)(5)(i1)Filing FCCID:2BE29-MSV02 GuangzhouMophomIndustrialCo.,Ltdcertifiesthatasofthedateofthefilingofthe application,theapplicantisnotidentifiedontheCoveredListasanentityproducing"covered equipment. Sincerely, SignaturewenClany OwenChong Manager AttestationLetter CFR47$2.911(dX(S)Xi)AttestationLetter

U.S. AGENT LETTER OF ATTESTATION Date: 2024-05-17 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2BE29-MSV02 Guangzhou Mophom Industrial Co.,Ltd certifies that, as of the date of the filing of the application, Iconsigh Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. Guangzhou Mophom Industrial Co.,Ltd accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Iconsigh Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: Iconsigh Inc. Address: 2310 Homestead Road, Suite C1, Los Altos, CA, 94024, USA FRN: 0033398652 Tel.: +1 (408) 320-9867 Email: [email protected] Signed by (printed name): Benjamin Kaur Signature: Applicant: Guangzhou Mophom Industrial Co.,Ltd Address: No.206 Commercial, No. 2, Huijing West Second Street,Huadu District, Guangzhou, Guangdong, China FRN: 0034954339 Tel: +86 02086972867 Email: [email protected] Signed by (printed name): Owen Chong Signature:

Applicant:GuangzhouMophomIndustrialCo.,Ltd Address:No.206Commercial,No.2,HuijingWestSecondStreet,HuaduDistrict, Guangzhou,Guangdong,China Tel:+8602086972867 Email:[email protected] Date:2024-05-17 FEDERALCOMMUNICATIONSCOMMISSIONS AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 Subject:AgentAuthorization Towhomitmayconcern: We,GuangzhouMophomIndustrialCo.,LtdherebyauthorizeWorldAllianceTesting &Certification(Shenzhen)Co.,Ltdtoactonitsbehalfinallmattersrelatingto applicationforEquipmentauthorization,includingthesigningofalldocumentsrelating tothesematters.AIlactscarriedoutbyWorldAllianceTesting&Certification (Shenzhen)Co.,Ltdonourbehalfshallhavethesameeffectasourownaction. We,theundersigned,herebycertifythatwearenotsubjecttoadenialoffederalbenefits, thatincludesFCCbenefits,pursuanttoSection5301oftheAnti-DrugAbuseActof1988, 21U.S.C.862. Thisauthorizationisvaliduntilfurtherwrittennoticefromtheapplicant. SincerelyYours, Signature:(QwenCng OwenChong Manager FCCAuthorization QA-FR-170-B

Report No.: RWAZ202300098 Page 1 of 4 EUT EXTERNAL PHOTOGRAPHS Report No.: RWAZ202300098 Page 2 of 4 Report No.: RWAZ202300098 Page 3 of 4 Report No.: RWAZ202300098 Page 4 of 4

Label: Label Location

Report No.: RWAZ202300098 Page 1 of 8 EUT INTERNAL PHOTOGRAPHS Report No.: RWAZ202300098 Page 2 of 8 Report No.: RWAZ202300098 Page 3 of 8 Report No.: RWAZ202300098 Page 4 of 8 Report No.: RWAZ202300098 Page 5 of 8 Report No.: RWAZ202300098 Page 6 of 8 Report No.: RWAZ202300098 Page 7 of 8 Report No.: RWAZ202300098 Page 8 of 8 ANT

Report No.: RWAZ202300098D Report Template: TR-4-E-011/V1 Page 1 of 7 RF Exposure Evaluation Report Report No.: RWAZ202300098C Applicant: Guangzhou MOPHOM Industrial Co.,Ltd Address: No.206 Commercial, No. 2,Huijing West Second Street,Huadu District,Guangzhou,Guangdong,China Product Name: Sous Vide Cooker Product Model: MSV02 Multiple Models: N/A Trade Mark: MOPHOM FCC ID: 2BE29-MSV02 Standards: 47 CFR §1.1307 KDB 447498 D04 Interim General RF Exposure Guidance v01 Test Date: 2024-06-12 Test Result: Complied Report Date: 2024-06-12 Reviewed by: Approved by: Frank Yin Project Engineer Jacob Kong Manager Prepared by: World Alliance Testing & Certification (Shenzhen) Co., Ltd No. 1002, East Block, Laobing Building, Xingye Road 3012, Xixiang street, Bao'an District, Shenzhen, Guangdong, People’s Republic of China This report may contain data that are not covered by the NVLAP accreditation and shall be marked with an asterisk “★” Report No.: RWAZ202300098D Report Template: TR-4-E-011/V1 Page 2 of 7 Announcement 1．This test report shall not be reproduced except in full, without the written approval of World Alliance Testing & Certification (Shenzhen) Co., Ltd 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above regulation. 4. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. 5. The information marked “#” is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. Revision History Version No. Issued Date Description 00 2024-06-12 Original Report No.: RWAZ202300098D Report Template: TR-4-E-011/V1 Page 3 of 7 Contents 1 General Information ............................................................................................................................ 4 1.1 Client Information ...................................................................................................................... 4 1.2 Product Description of EUT ....................................................................................................... 4 1.3 Laboratory Location ................................................................................................................... 4 2 RF Exposure Evaluation ..................................................................................................................... 5 2.1 Standard .................................................................................................................................... 5 2.2 Result......................................................................................................................................... 7 Report No.: RWAZ202300098D Report Template: TR-4-E-011/V1 Page 4 of 7 1 General Information 1.1 Client Information Applicant: Guangzhou MOPHOM Industrial Co.,Ltd Address: No.206 Commercial, No. 2,Huijing West Second Street,Huadu District,Guangzhou,Guangdong,China Manufacturer: Guangzhou MOPHOM Industrial Co.,Ltd Address: No.206 Commercial, No. 2,Huijing West Second Street,Huadu District,Guangzhou,Guangdong,China 1.2 Product Description of EUT The EUT is Sous Vide Cooker that contains BLE and 2.4G WLAN radios. Sample Serial Number 21-3 (assigned by WATC) Sample Received Date 2024-01-03 Sample Status Good Condition Frequency Range 2.4G WLAN: 2412MHz - 2462MHz BLE: 2402MHz - 2480MHz Maximum Conducted Output Power 2412MHz - 2462MHz: 19.21dBm 2402MHz - 2480MHz: 5.28dBm Modulation Technology DSSS, OFDM, GFSK Antenna Gain # 2.54dBi Spatial Streams SISO (1TX, 1RX) Power Supply AC 120V/60Hz Adapter Information N/A Modification Sample No Modification by the test lab 1.3 Laboratory Location World Alliance Testing & Certification (Shenzhen) Co., Ltd No. 1002, East Block, Laobing Building, Xingye Road 3012, Xixiang street, Bao'an District, Shenzhen, Guangdong, People’s Republic of China Tel: +86-755-29691511, Email: [email protected] The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 463912, the FCC Designation No. : CN5040. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0160. Report No.: RWAZ202300098D Report Template: TR-4-E-011/V1 Page 5 of 7 2 RF Exposure Evaluation 2.1 Standard According to §1.1307(b)(3)(i), For single RF sources (i.e., any single fixed RF source, mobile device, or portable device, as defined in paragraph (b)(2) of this section): A single RF source is exempt if: (A) The available maximum time-averaged power is no more than 1 mW, regardless of separation distance. This exemption may not be used in conjunction with other exemption criteria other than those in paragraph (b)(3)(ii)(A) of this section. Medical implant devices may only use this exemption and that in paragraph (b)(3)(ii)(A); (B) Or the available maximum time-averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold Pth (mW) described in the following formula. This method shall only be used at separation distances (cm) from 0.5 centimeters to 40 centimeters and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by: (C) Or using Table 1 and the minimum separation distance (R in meters) from the body of a nearby person for the frequency (f in MHz) at which the source operates, the ERP (watts) is no more than the calculated value prescribed for that frequency. For the exemption in Table 1 to apply, R must be at least λ/2π, where λ is the free-space operating wavelength in meters. If the ERP of a single RF source is not easily obtained, then the available maximum time-averaged power may be used in li…

Text truncated - open the document above for the full version.

AntennaSpecification Manufacture：TUYA ProductName：WBR1Antenna AntennaType：PCB TestDate：2019.05.20 Testedby：LongWang Approvedby：Licco Content 1.GeneralDescription.................................................................................1 2.TestConfigurations...................................................................................2 2.1TestEnvironment............................................................................2 2.2TestEquipment...............................................................................2 2.3TestPrinciple...................................................................................2 3.TestResults..............................................................................................3 3.1GainandEfficiency..........................................................................3 3.2RadiationPattern............................................................................4 4.AntennaDimensions................................................................................6 5.EUTPhoto................................................................................................6 6.TestSetupPhoto......................................................................................7 1 1.GeneralDescription ManufacturerHangzhouTuyaInformationTechnologyCo.,Ltd Address Room701,Building3,MoreCenter,No.87GuDunRoad, Hangzhou,Zhejiang,China TestLocation Room106,Building3,LetongSciencePark,No.500, QiuyiRoad,BinjiangDistrict,Hangzhou ProductNameWBR1Antenna Productmodel WBR1 AntennaType PCBAntenna TestItems Gain;Efficiency;RadiationPattern TestFrequency 2400-2500MHz TestStandard ANSI/IEEEStd149-1979 2 2.TestConfigurations 2.1TestEnvironment Temperature(°C)25 Humidity(%RH)60 AtmosphericPressure(kPa)100.5 2.2TestEquipment TestSystemTEM24Multi-probeMicrowaveChamber TestInstrumentAgilentE5071B 2.3TestPrinciple 3 3.TestResults 3.1GainandEfficiency Frequency(MHz)PeakGain(dBi)Efficiency(%) 24001.6252.29 24101.7152.17 24201.9353.14 24301.9854.16 24402.0057.62 24502.1759.64 24602.4561.55 24702.3860.64 24802.5462.86 24902.3059.85 25002.4960.41 4 3.2RadiationPattern Phi02D Phi902D 5 Theta902D 2480MHz3D 6 4.AntennaDimensions 5.EUTPhoto 7 6.TestSetupPhoto

Report No.: RWAZ202300098A Report Template: TR-4-E-009/V1 Page 1 of 36 FCC Test Report Report No.: RWAZ202300098A Applicant: Guangzhou MOPHOM Industrial Co.,Ltd Address: No.206 Commercial, No. 2,Huijing West Second Street,Huadu District,Guangzhou,Guangdong,China Product Name: Sous Vide Cooker Product Model: MSV02 Multiple Models: N/A Trade Mark: MOPHOM FCC ID: 2BE29-MSV02 Standards: FCC CFR Title 47 Part 15C (§15.247) Test Date: 2024-01-04 to 2024-06-12 Test Result: Complied Report Date: 2024-06-12 Reviewed by: Approved by: Frank Yin Project Engineer Jacob Kong Manager Prepared by: World Alliance Testing & Certification (Shenzhen) Co., Ltd No. 1002, East Block, Laobing Building, Xingye Road 3012, Xixiang street, Bao'an District, Shenzhen, Guangdong, People’s Republic of China This report may contain data that are not covered by the NVLAP accreditation and shall be marked with an asterisk “★” Report No.: RWAZ202300098A Report Template: TR-4-E-009/V1 Page 2 of 36 Announcement 1．This test report shall not be reproduced except in full, without the written approval of World Alliance Testing & Certification (Shenzhen) Co., Ltd 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above regulation. 4. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. 5. The information marked “#” is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. Revision History Version No. Issued Date Description 00 2024-06-12 Original Report No.: RWAZ202300098A Report Template: TR-4-E-009/V1 Page 3 of 36 Contents 1 General Information ............................................................................................................................ 4 1.1 Client Information ...................................................................................................................... 4 1.2 Product Description of EUT ....................................................................................................... 4 1.3 Antenna information .................................................................................................................. 4 1.4 Related Submittal(s)/Grant(s) .................................................................................................... 5 1.5 Measurement Uncertainty ......................................................................................................... 5 1.6 Laboratory Location ................................................................................................................... 5 1.7 Test Methodology ...................................................................................................................... 5 2 Description of Measurement .............................................................................................................. 6 2.1 Test Configuration ...................................................................................................................... 6 2.2 Test Auxiliary Equipment ........................................................................................................... 6 2.3 Test Setup .................................................................................................................................. 7 2.4 Test Procedure .......................................................................................................................... 9 2.5 Measurement Method.............................................................................................................. 10 2.6 Measurement Equipment ......................................................................................................... 11 3 Test Results ....................................................................................................................................... 12 3.1 Test Summary .......................................................................................................................... 12 3.2 Limit ......................................................................................................................................... 13 3.3 AC Line Conducted Emissions Test Data ................................................................................ 14 3.4 Radiated emission Test Data ................................................................................................... 18 3.5 RF Conducted Test Data ......................................................................................................... 25 3.5.1 6 dB Emission Bandwidth and 99% Occupied Bandwidth ........................................... 25 3.5.2 Maximum Conducted Peak Output Power ................................................................... 25 3.5.3 Power Spectral Density ................................................................................................ 26 3.5.4 100 kHz Bandwidth of Frequency Band Edge ............................................................. 26 3.5.5 Duty Cycle .................................................................................................................... 26 4 Test Setup Photo ............................................................................................................................... 35 5 E.U.T Photo ........................................................................................................................................ 36 Report No.: RWAZ202300098A Report Template: TR-4-E-009/V1 Page 4 of 36 1 General Information 1.1 Client Information Applicant: Guangzhou MOPHOM Industrial Co.,Ltd Address: No.206 Commercial, No. 2,Huijing West Second Street,Huadu District,Guangzhou,Guangdong,China Manufacturer: Gua…

Text truncated - open the document above for the full version.

Report No.: RWAZ202300098C Report Template: TR-4-E-008/V1.1 Page 1 of 31 FCC Test Report Report No.: RWAZ202300098C Applicant: Guangzhou MOPHOM Industrial Co.,Ltd Address: No.206 Commercial, No. 2,Huijing West Second Street,Huadu District,Guangzhou,Guangdong,China Product Name: Sous Vide Cooker Product Model: MSV02 Multiple Models: N/A Trade Mark: MOPHOM FCC ID: 2BE29-MSV02 Standards: FCC CFR Title 47 Part 15C (§15.247) Test Date: 2024-05-31 to 2024-06-12 Test Result: Complied Report Date: 2024-06-12 Reviewed by: Approved by: Frank Yin Project Engineer Jacob Kong Manager Prepared by: World Alliance Testing & Certification (Shenzhen) Co., Ltd No. 1002, East Block, Laobing Building, Xingye Road 3012, Xixiang street, Bao'an District, Shenzhen, Guangdong, People’s Republic of China This report may contain data that are not covered by the NVLAP accreditation and shall be marked with an asterisk “★” Report No.: RWAZ202300098C Report Template: TR-4-E-008/V1.1 Page 2 of 31 Announcement 1. This test report shall not be reproduced except in full, without the written approval of World Alliance Testing & Certification (Shenzhen) Co., Ltd 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above regulation. 4. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. 5. The information marked “#” is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. Revision History Version No. Issued Date Description 00 2024-06-12 Original Report No.: RWAZ202300098C Report Template: TR-4-E-008/V1.1 Page 3 of 31 Contents 1 General Information ............................................................................................................................ 4 1.1 Client Information ...................................................................................................................... 4 1.2 Product Description of EUT ....................................................................................................... 4 1.3 Antenna information .................................................................................................................. 4 1.4 Related Submittal(s)/Grant(s) .................................................................................................... 5 1.5 Measurement Uncertainty ......................................................................................................... 5 1.6 Laboratory Location ................................................................................................................... 5 1.7 Test Methodology ...................................................................................................................... 5 2 Description of Measurement .............................................................................................................. 6 2.1 Test Configuration ...................................................................................................................... 6 2.2 Test Auxiliary Equipment ........................................................................................................... 6 2.3 Test Setup .................................................................................................................................. 7 2.4 Test Procedure .......................................................................................................................... 9 2.5 Measurement Method.............................................................................................................. 10 2.6 Measurement Equipment ........................................................................................................ 10 3 Test Results ....................................................................................................................................... 12 3.1 Test Summary .......................................................................................................................... 12 3.2 Limit ......................................................................................................................................... 13 3.3 AC Line Conducted Emissions Test Data ................................................................................ 14 3.4 Radiated emission Test Data ................................................................................................... 18 3.5 RF Conducted Test Data ......................................................................................................... 24 3.5.1 6 dB Emission Bandwidth and 99% Occupied Bandwidth ........................................... 24 3.5.2 Maximum Conducted Peak Output Power ................................................................... 24 3.5.3 Power Spectral Density ................................................................................................ 24 3.5.4 100 kHz Bandwidth of Frequency Band Edge ............................................................. 24 3.5.5 Duty Cycle .................................................................................................................... 24 4 Test Setup Photo ..........................................................................................................................…

Text truncated - open the document above for the full version.