2BE9U-T8PROSmart Watch

T8pro This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Shenzhen Huadai Technology Co., Ltd Covered Equipment Certification Attestation Letter 6/2/2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2BE9U-T8PRO Shenzhen Huadai Technology Co., Ltd (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Shenzhen Huadai Technology Co., Ltd (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Shenzhen Huadai Technology Co., Ltd (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). <Signature>: Name: Wei Chuchao Title: Manager Company: Shenzhen Huadai Technology Co., Ltd Date: 6/2/2026

Shenzhen Huadai Technology Co., Ltd * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter 6/2/2026 TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTN.: Reviewing Engineer FCC ID: 2BE9U-T8PRO FRN of applicant: 0035058932 Per section 2.911(d)(7) of the FCC rules, [Shenzhen Huadai Technology Co., Ltd] (“the applicant”) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: Herland International Trading Inc FCC Registration Number (FRN): 0036324101 Physical U.S. Company Address: 1370 Valley Vista Dr Ste 200 Diamond Bar, CA 91765 Contact Person: Jianfeng Gao Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Signed: Printed name: Wei Chuchao Title: Manager Company Name: Shenzhen Huadai Technology Co., Ltd Date: 6/2/2026 Agent Signed (if different from Applicant): Signed: Printed name: Jianfeng Gao Title: Manager Company Name: Herland International Trading Inc Date: 3/2/2026

Shenzhen Huadai Technology Co., Ltd 2026-05-25 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen DL Testing Technology Co., Ltd.（101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China）to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Shenzhen Huadai Technology Co., Ltd（A308, Fuji Industrial Park, No.33 Liuhe Road, Henggang Street, Longgang District, Shenzhen, China） <Signature>: Name: Wei Chuchao Title: Manager Company: Shenzhen Huadai Technology Co., Ltd

Shenzhen Huadai Technology Co., Ltd 2026-05-25 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, <Signature>: Name: Wei Chuchao Title: Manager Company: Shenzhen Huadai Technology Co., Ltd

Shenzhen Huadai Technology Co., Ltd 2026-05-25 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BE9U-T8PRO Product Name: Smart Watch Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description  BOM These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature>: Name: Wei Chuchao Title: Manager Company: Shenzhen Huadai Technology Co., Ltd

Shenzhen Huadai Technology Co., Ltd FCC ID: 2BE9U-T8PRO Product Similarity Declaration Applicant: Shenzhen Huadai Technology Co., Ltd Address: A308, Fuji Industrial Park, No.33 Liuhe Road, Henggang Street, Longgang District, Shenzhen, China Manufacturer: Shenzhen Huadai Technology Co., Ltd Address: A308, Fuji Industrial Park, No.33 Liuhe Road, Henggang Street, Longgang District, Shenzhen, China Product Name: Smart Watch Trade Mark: N/A Model Number: T8pro, F8pro We (Shenzhen Huadai Technology Co., Ltd) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.,), same mechanical structure and design (including product enclosure, materials, etc.,), All models are the same as the samples except for the model name and appearance color. <Signature>: Name: Wei Chuchao Title: Manager Company: Shenzhen Huadai Technology Co., Ltd

Shenzhen DL Testing Technology Co., Ltd. EUT PHOTO(External Photos) Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. ※※※※※ END OF REPORT ※※※※※

Size:15*12mm M/N: T8pro FCC ID: 2BE9U-T8PRO Label location

Shenzhen DL Testing Technology Co., Ltd. EUT PHOTO(Internal Photos) ANT Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. ※※※※※ END OF REPORT ※※※※※

FCC ID: 2BE9U-T8PRO RF Exposure Evaluation According to KDB 447498 D01 V06 and part 2.1093，Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, Mw) / (min. test separation distance, mm)] · [√f (GHz) ] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where f (GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest Mw and mm before calculation The result is rounded to one decimal place for comparison EIRP=E Meas +20log(d Meas )-104.7 EIRP is the equivalent isotropically radiated power, in dBm E Meas is the field strength of the emission at the measurement distance, in dBμV/m d Meas is the measurement distance, in m Here, EDR Conducted power (dBm) Max tune-up (Mw) Frequency (MHz) Min. distance(mm) Calc. thresholds limit 3.58 2.28 2441 5 0.71 3.0 BLE Conducted power (dBm) Max tune-up (Mw) Frequency (MHz) Min. distance(mm) Calc. thresholds limit -1.77 0.67 2440 5 0.21 3.0 So a SAR test is not required

Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260509059R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 1 of 27 FCC Part 15C Test Report FCC ID: 2BE9U-T8PRO Applicant: Shenzhen Huadai Technology Co., Ltd Address: A308, Fuji Industrial Park, No.33 Liuhe Road, Henggang Street, Longgang District, Shenzhen, China Manufacturer: Shenzhen Huadai Technology Co., Ltd Address: A308, Fuji Industrial Park, No.33 Liuhe Road, Henggang Street, Longgang District, Shenzhen, China Product Name: Smart Watch Trade Mark: N/A Model Number: T8pro, F8pro Date of Receipt: May. 08, 2026 Test Date: May. 08, 2026 - May. 26, 2026 Date of Report: May. 26, 2026 Prepared By: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China Applicable Standards: FCC PART 15 C 15.247 ANSI C63.10:2020 Test Result: Pass Report Number: DLE-260509059R Prepared (Test Engineer): Alisa Song Reviewer (Supervisor): Jack Bu Approved (Manager): Jade Yang This test report is based on a single evaluation of one sample of above mentioned products. It is not permitted to be duplicated in extracts without written approval of Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260509059R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 2 of 27 Table of Contents Page 1. . SUMMARY OF TEST RESULTS 4 1.1. MEASUREMENT UNCERTAINTY 4 2. . GENERAL INFORMATION 5 2.1. GENERAL DESCRIPTION OF EUT 5 2.2. DESCRIPTION OF TEST MODES 6 2.3. BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 6 2.4. DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 7 2.5. TABLE OF PARAMETERS OF TEST SOFTWARE SETTING 7 2.6. EQUIPMENTS LIST FOR ALL TEST ITEMS 8 3. . EMC EMISSION TEST 9 3.1. CONDUCTED EMISSION MEASUREMENT 9 3.1.1. POWER LINE CONDUCTED EMISSION LIMITS 9 3.1.2. TEST PROCEDURE 9 3.1.3. DEVIATION FROM TEST STANDARD 9 3.1.4. TEST SETUP 10 3.1.5. EUT OPERATING CONDITIONS 10 3.1.6. TEST RESULTS 11 3.2. RADIATED EMISSION MEASUREMENT 13 3.2.1. RADIATED EMISSION LIMITS 13 3.2.2. TEST PROCEDURE 14 3.2.3. DEVIATION FROM TEST STANDARD 14 3.2.4. TEST SETUP 14 3.2.5. EUT OPERATING CONDITIONS 15 3.2.6. TEST RESULTS (BETWEEN 9KHZ – 30 MHZ) 16 3.2.7. TEST RESULTS (BETWEEN 30MHZ – 1GHZ) 17 3.2.8. TEST RESULTS (1GHZ~25GHZ) 19 3.3 RADIATED BAND EMISSION MEASUREMENT 20 3.3.1 TEST REQUIREMENT: 20 3.3.2 TEST PROCEDURE 20 3.3.3 DEVIATION FROM TEST STANDARD 20 3.3.4 TEST SETUP 21 3.3.5 EUT OPERATING CONDITIONS 21 3.4 CONDUCTED BAND EDGE EMISSION&CONDUCTED SPURIOUS EMISSIONS MEASUREMENT 23 3.4.1 APPLICABLE STANDARD 23 3.4.2 TEST PROCEDURE 23 3.4.3 DEVIATION FROM STANDARD 23 3.4.4 TEST SETUP 23 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260509059R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 3 of 27 Table of Contents Page 3.4.5 EUT OPERATION CONDITIONS 23 3.4.6 TEST RESULTS 23 4. . PEAK OUTPUT POWER 24 4.1. APPLIED PROCEDURES / LIMIT 24 4.1.1. TEST PROCEDURE 24 4.1.2. DEVIATION FROM STANDARD 24 4.1.3. TEST SETUP 24 4.1.4. EUT OPERATION CONDITIONS 24 4.1.5. TEST RESULTS 24 5. . POWER SPECTRAL DENSITY TEST 25 5.1. APPLIED PROCEDURES / LIMIT 25 5.1.1. TEST PROCEDURE 25 5.1.2. DEVIATION FROM STANDARD 25 5.1.3. TEST SETUP 25 5.1.4. EUT OPERATION CONDITIONS 25 5.1.5. TEST RESULTS 25 6. . 6DB BANDWIDTH TEST 26 6.1. APPLIED PROCEDURES / LIMIT 26 6.1.1. TEST PROCEDURE 26 6.1.2. DEVIATION FROM STANDARD 26 6.1.3. TEST SETUP 26 6.1.4. EUT OPERATION CONDITIONS 26 6.1.5. TEST RESULTS 26 7. . ANTENNA REQUIREMENT 27 7.1. STANDARD REQUIREMENT 27 7.2. EUT ANTENNA 27 8. . TEST SEUUP PHOTO 27 9. . EUT PHOTO 27 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260509059R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 4 of 27 1.. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.247) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.205, 15.209, 15.247(d) Radiated Spurious Emission PASS 15.209, 15.205 Band Edge Emission PASS 15.247(b) Peak Output Power PASS 15.247(a)(2) 6dB Bandwidth PASS 15.247(e) Power Spectral Density PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Test lab: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China FCC Test Firm Registration Number: 854456 Designation Number: CN1307 IC Registered No.: 27485 CAB ID.: CN0118 1.1. MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±2.56dB 2 RF power,conducted ±0.42dB 3 Spurious emissions,conducted ±2.76dB 4 All emissions,radiated(<1G) ±3.65dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% 8 6dB Bandwidth ±0.2MHz 9 Power Spectral Density ±0.3dBm Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260509059R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 5 of 27 2.. GENERAL INFORMATION 2.1. GENERAL DESCRIPTION OF EUT Product Name: Smart Watch Trade Mark: N/A Model Number: T8pro, F8pro Test Model: T8pro Model Difference: All models are same as the samples except model name and appearance color, they have the same structure and circuit. Operation Frequency: 2402~2480MHz Channel numbers: 40 Channels Channel separation: 2MHz Data Rate: 1Mbps Modulation technology: GFSK Antenna Type: Internal Antenna Antenna gain: 0.17 dBi Power supply: DC 5V DC 3.85V from battery Note: 1.For a more detailed feature…

Text truncated - open the document above for the full version.

Shenzhen Yiantong Cable Co., LTD Address: Building 21, Wanfeng 98 Industrial City, Shajing Street, Bao 'an District, Shenzhen City 天线规格承认书 Antenna Specification for Approval 客 户 名称 CustomerName： 产品名称： ProductName： 2.4G 产品料号： Part NO.: C10- 35- 2.5 制 表 ： WriteBy：庄杰彬 日 期： IssuedDate: 2021- 10-08 工程R& D Dept 采购Business Dept 承认 Approved By 研发R& D Dept 工程 Engineer Dept 审核 Approval 庄彩虹 庄杰彬 庄杰彬 Product Specification A.ElectricalCharacteristics Frequency 2400MHz ~2500MHz VSWR<3.0 Efficiency >30% Impedance 50 Ohm Polarization Line Gain 0.17DBi B.Material & MechanicalCharacteristics Material of Radiator Cu Cable Type 1.0 19P Connector Type : NO Dimension C.Environmental Operation Temperature - 30 °C ~ + 80 °CStorage Temperature - 30 °C~+ 85 °C Test Equipment & Conditions 1.NetworkAnalyzers: Agilent 8753D 5071C 2.Communications TestSet: Agilent E5525C 3.3D Chamber TestSystem Effiency& Gain Radiation Pattern: (dBi)

Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 1 of 20 FCC ID: 2BE9U-T8PRO Applicant: Shenzhen Huadai Technology Co., Ltd Address: A308, Fuji Industrial Park, No.33 Liuhe Road, Henggang Street, Longgang District, Shenzhen, China Manufacturer: Shenzhen Huadai Technology Co., Ltd Address: A308, Fuji Industrial Park, No.33 Liuhe Road, Henggang Street, Longgang District, Shenzhen, China Product Name: Smart Watch Trade Mark: N/A Model Number: T8pro, F8pro Date of Receipt: May. 08, 2026 Test Date: May. 08, 2026 - May. 26, 2026 Date of Report: May. 26, 2026 Prepared By: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China Applicable Standards: FCC PART 15 C 15.247 ANSI C63.10:2020 Test Result: Pass Report Number: DLE-260509059R Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 2 of 20 Maximum Peak Conducted Output Power Condition Mode Frequency (MHz) Antenna Conducted Power (dBm) Limit Conducted(dBm) Verdict NVNT BLE 1M 2402 Ant1 -1.91 30 Pass NVNT BLE 1M 2440 Ant1 -1.77 30 Pass NVNT BLE 1M 2480 Ant1 -2.07 30 Pass Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 3 of 20 Peak Power NVNT BLE 1M 2402MHz Ant1 Peak Power NVNT BLE 1M 2440MHz Ant1 Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 4 of 20 Peak Power NVNT BLE 1M 2480MHz Ant1 Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 5 of 20 -6dB Bandwidth Condition Mode Frequency (MHz) Antenna -6 dB Bandwidth (MHz) Limit -6 dB Bandwidth (MHz) Verdict NVNT BLE 1M 2402 Ant1 0.6509 0.5 Pass NVNT BLE 1M 2440 Ant1 0.6447 0.5 Pass NVNT BLE 1M 2480 Ant1 0.6401 0.5 Pass Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 6 of 20 -6dB Bandwidth NVNT BLE 1M 2402MHz Ant1 -6dB Bandwidth NVNT BLE 1M 2440MHz Ant1 Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 7 of 20 -6dB Bandwidth NVNT BLE 1M 2480MHz Ant1 Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 8 of 20 Occupied Channel Bandwidth Condition Mode Frequency (MHz) Antenna 99% OBW (MHz) NVNT BLE 1M 2402 Ant1 1.0381 NVNT BLE 1M 2440 Ant1 1.0357 NVNT BLE 1M 2480 Ant1 1.0381 Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 9 of 20 OBW NVNT BLE 1M 2402MHz Ant1 OBW NVNT BLE 1M 2440MHz Ant1 Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 10 of 20 OBW NVNT BLE 1M 2480MHz Ant1 Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 11 of 20 Maximum Power Spectral Density Level Condition Mode Frequency (MHz) Antenna Conducted PSD (dBm/3kHz) Limit (dBm/3kHz) Verdict NVNT BLE 1M 2402 Ant1 -12.34 8 Pass NVNT BLE 1M 2440 Ant1 -13.22 8 Pass NVNT BLE 1M 2480 Ant1 -12.65 8 Pass Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 12 of 20 PSD NVNT BLE 1M 2402MHz Ant1 PSD NVNT BLE 1M 2440MHz Ant1 Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 13 of 20 PSD NVNT BLE 1M 2480MHz Ant1 Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 14 of 20 Band Edge Condition Mode Frequency (MHz) Antenna Max Value (dBc) Limit (dBc) Verdict NVNT BLE 1M 2402 Ant1 -47.24 -30 Pass NVNT BLE 1M 2480 Ant1 -52.57 -30 Pass Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 15 of 20 Band Edge NVNT BLE 1M 2402MHz Ant1 Ref Band Edge NVNT BLE 1M 2402MHz Ant1 Emission Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 16 of 20 Band Edge NVNT BLE 1M 2480MHz Ant1 Ref Band Edge NVNT BLE 1M 2480MHz Ant1 Emission Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 17 of 20 Conducted RF Spurious Emission Condition Mode Frequency (MHz) Antenna Max Value (dBc) Limit (dBc) Verdict NVNT BLE 1M 2402 Ant1 -35.68 -20 Pass NVNT BLE 1M 2440 Ant1 -34.73 -20 Pass NVNT BLE 1M 2480 Ant1 -32.89 -20 Pass Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 18 of 20 Tx. Spurious NVNT BLE 1M 2402MHz Ant1 Ref Tx. Spurious NVNT BLE 1M 2402MHz Ant1 Emission Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 19 of 20 Tx. Spurious NVNT BLE 1M 2440MHz Ant1 Ref Tx. Spurious NVNT BLE 1M 2440MHz Ant1 Emission Report Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 20 of 20 Tx. Spurious NVNT BLE 1M 2480MHz Ant1 Ref Tx. Spurious NVNT BLE 1M 2480MHz Ant1 Emission

Shenzhen DL Testing Technology Co., Ltd. EUT TEST PHOTO Radiated Measurement Photos Shenzhen DL Testing Technology Co., Ltd. Conducted Measurement Photos ※※※※※ END OF REPORT ※※※※※