2BE9V-D6Notebook computer

本产品不带电源适配器销售 ，消费者应配套购买使用获得3C 认证并满足标准要求的电源适配器。 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harm full interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Specific Absorption Rate (SAR) information: This Device meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: Device has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the device kept 0mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain an 0mm separation distance between the user's body and the back of the device. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.

Shenzhen Hongjie Chuang Technology Co. , Ltd Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-3-7 To whom it may concern: We, Shenzhen Hongjie Chuang Technology Co. , Ltd, hereby certify that the equipment for which authorization is sought (FCC ID: 2BE9V-D6) is not “covered” equipment prohibited from receiving an equipment authorization pursuant to § 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing “covered” equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, Signature May Hu Manager Shenzhen Hongjie Chuang Technology Co. , Ltd 62_[model] CoveredEqu_2.911(d)(5)(i) and (ii) - U, V03

Shenzhen Hongjie Chuang Technology Co. , Ltd Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024/03/06 U.S. Agent Designation Shenzhen Hongjie Chuang Technology Co. , Ltd acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BE9V-D6): Name and company of U.S. agent: GSS SERVICE INC Physical U.S. address of agent: 6547 N Academy Blvd #2266 Colorado Springs COLORADO 80918 United States FRN of U.S. agent: 0033402082 Email address of U.S. agent: [email protected] GSS SERVICE INC acknowledges their obligation to accept service of process on behalf of Shenzhen Hongjie Chuang Technology Co. , Ltd Shenzhen Hongjie Chuang Technology Co. , Ltd with the FRN [0035058940] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature May Hu Manager Shenzhen Hongjie Chuang Technology Co. , Ltd Signature Michoux Logan PM GSS SERVICE INC 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

Shenzhen Hongjie Chuang Technology Co. , Ltd Add: Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen China Date: 2024-3-7 FCC ID: 2BE9V-D6 Dear Sir/Madam, We, Shenzhen Hongjie Chuang Technology Co. , Ltd Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model: Product name: Notebook computer Model no.: D6, D7, D8, D9, E6, E7, E8, E9, Q6, Q7, Q8, Q9, T6, T7, TB, T9, Z6, Z7, Z8, Z9 Sincerely, Name/Title： May Hu/Manager Company: Shenzhen Hongjie Chuang Technology Co. , Ltd Address: Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen China Phone: 18924675176 Fax: N/A E-Mail: [email protected]

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2024-3-7> Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2BE9V-D6 D6 For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title： May Hu/Manager Company: Shenzhen Hongjie Chuang Technology Co. , Ltd Address: Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen China Phone: 18924675176 Fax: N/A E-Mail: [email protected]

Shenzhen Hongjie Chuang Technology Co. , Ltd Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen China Date: 2024-3-7 FCC ID: 2BE9V-D6 Model Number: D6 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD To Whom It May Concern, We, Shenzhen Hongjie Chuang Technology Co. , Ltd, declare that this EUT (FCC ID: 2BE9V-D6) doesn’t have Ad Hoc mode function on “non-US/Canada frequencies”. In addition. The frequency selection feature is disabled by firmware for devices marked to the US/Canada. For DTS part of this device, only channels 1-11 will be used in North America, Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, Name/Title： May Hu/Manager Company: Shenzhen Hongjie Chuang Technology Co. , Ltd Address: Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen China Phone: 18924675176 Fax: N/A E-Mail: [email protected]

Shenzhen Hongjie Chuang Technology Co. , Ltd Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-3-7 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2BE9V-D6 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins’ current valid General Terms and Conditions (AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title： May Hu/Manager Company: Shenzhen Hongjie Chuang Technology Co. , Ltd Address: Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen China Phone: 18924675176 Fax: N/A E-Mail: [email protected]

FCC ID: 2BE9V-D6 External Photos of the EUT FCC ID: 2BE9V-D6 FCC ID: 2BE9V-D6

Label and Location Size: L: 4.0cm*W: 3.0cm Label and Location Model No.: D6 FCC ID : 2BE9V-D6

FCC ID: 2BE9V-D6 Internal Photos of the EUT BT/2.4G WIFI/5G WIFI PIFA Antenna 1 2.4G WIFI/5G WIFI PIFA Antenna 2 FCC ID: 2BE9V-D6 FCC ID: 2BE9V-D6 FCC ID: 2BE9V-D6 FCC ID: 2BE9V-D6 FCC ID: 2BE9V-D6 FCC ID: 2BE9V-D6 FCC ID: 2BE9V-D6 FCC ID: 2BE9V-D6

Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China TEST REPORT Report Reference No. ..................... : FCC ID ........................................... : CTA24022202605 2BE9V-D6 Compiled by ( position+printed name+signature) .. : File administrators Zoey Cao Supervised by ( position+printed name+signature) .. : Project Engineer Amy Wen Approved by ( position+printed name+signature) .. : RF Manager Eric Wang Date of issue ..................................... : Mar. 05, 2024 Testing Laboratory Name .............. : Shenzhen CTA Testing Technology Co., Ltd. Address ............................................. : Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao‘an District, Shenzhen, China Applicant’s name ............................ : Shenzhen Hongjie Chuang Technology Co., Ltd Address ............................................. : Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen, China Test specification ........................... : Standard ........................................... : IEC 62209-2:2010; IEEE 1528:2013; FCC 47 CFR Part 2.1093; ANSI/IEEE C95.1:2005; Reference FCC KDB 447498; KDB 248227; KDB 616217; KDB 865664 Shenzhen CTA Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTA Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTA Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description ..................... : Notebook computer Trade Mark........................................ : N/A Manufacturer ..................................... : Shenzhen Hongjie Chuang Technology Co. , Ltd Model/Type reference ....................... : D6 Listed Models .................................. : D7, D8, D9, E6, E7, E8, E9, Q6, Q7, Q8, Q9, T6, T7, TB, T9, Z6, Z7, Z8, Z9 Rating ............................................... : DC 7.7V From battery and DC 12.0V From external circuit Result ................................................ : PASS Report No.: CTA24022202605 Page 2 of 74 T E S T R E P O R T Equipment under Test : Notebook computer Model /Type : D6 Series Model No. D7, D8, D9, E6, E7, E8, E9, Q6, Q7, Q8, Q9, T6, T7, TB, T9, Z6, Z7, Z8, Z9 Applicant : Shenzhen Hongjie Chuang Technology Co. , Ltd Address : Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen, China Manufacturer : Shenzhen Hongjie Chuang Technology Co. , Ltd Address : Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen, China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: CTA24022202605 Page 3 of 74 Contents 1 Statement of Compliance ............................................................................................................................. 6 2 General Information ..................................................................................................................................... 7 2.1 General Remarks ............................................................................................................................................. 7 2.2 Description of Equipment Under Test (EUT) ..................................................................................................... 7 2.3 Device Category and SAR Limits ..................................................................................................................... 8 2.4 Applied Standard .............................................................................................................................................. 8 2.5 Test Facility ....................................................................................................................................................... 9 2.6 Environment of Test Site ................................................................................................................................... 9 2.7 Test Configuration ............................................................................................................................................. 9 3 Specific Absorption Rate (SAR) ................................................................................................................. 10 3.1 Introduction ..................................................................................................................................................... 10 3.2 SAR Definition ................................................................................................................................................ 10 4 SAR Measurement System ........................................................................................................................ 11 4.1 E-Field Probe ................................................................................................................................................... 11 4.2 Data Acquisition Electronics (DAE) ................................................................................................................. 12 4.3 Robot .............................................................................................................................................................. 13 4.4 Measurement Server ...................................................................................................................................... 13 4.5 Phantom ...................................................................…

Text truncated - open the document above for the full version.

1. Antenna Description: Antenna type PIFA antenna Model D6 Frequency range 2400-2500MHz Manufacturer Shenzhen Hongjie Chuang Technology Co. , Ltd ANT Peak Gain 0.95 dBi 2. Antenna Photo: Length: 29.85mm Width: 19.39mm 3. Test Equipment & Conditions 3.1 Test instrument VSWR is tested using Agilent E5071B connected to a hand mechanism, and the status is free space. 3.2 Test environment and methods 4．Antenna Radiation Pattern 2400MHz 2450MHz 2500MHz

Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao‘an District, Shenzhen, China Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn FCC PART 15 SUBPART C TEST REPORT FCC PART 15.247 Report Reference No. ..................... : FCC ID. ............................................ : CTA24022202601 2BE9V-D6 Compiled by ( position+printed name+signature) .. : File administrators Zoey Cao Supervised by ( position+printed name+signature) .. : Project Engineer Amy Wen Approved by ( position+printed name+signature) .. : RF Manager Eric Wang Date of issue ..................................... : Mar. 02, 2024 Testing Laboratory Name .............. : Shenzhen CTA Testing Technology Co., Ltd. Address ............................................ : Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao‘an District, Shenzhen, China Applicant’s name ............................ : Shenzhen Hongjie Chuang Technology Co. , Ltd Address ............................................ : Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen, China Test specification ...........................: Standard ........................................... : FCC Part 15.247 Shenzhen CTA Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTA Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTA Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Equipment description...................: Notebook computer Trade Mark ....................................... : N/A Manufacturer .................................... : Shenzhen Hongjie Chuang Technology Co. , Ltd Model/Type reference....................... : D6 Listed Models .................................. : D7, D8, D9, E6, E7, E8, E9, Q6, Q7, Q8, Q9, T6, T7, TB, T9, Z6, Z7, Z8, Z9 Modulation ....................................... : GFSK Frequency .......................................... From 2402MHz to 2480MHz Ratings ............................................. : DC 7.7V From battery and DC 12.0V From external circuit Result................................................ : PASS Report No.: CTA24022202601 Page 2 of 42 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn T E S T R E P O R T Equipment under Test : Notebook computer Model /Type : D6 Listed Models : D7, D8, D9, E6, E7, E8, E9, Q6, Q7, Q8, Q9, T6, T7, TB, T9, Z6, Z7, Z8, Z9 Applicant : Shenzhen Hongjie Chuang Technology Co. , Ltd Address : Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen, China Manufacturer : Shenzhen Hongjie Chuang Technology Co. , Ltd Address : Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen, China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: CTA24022202601 Page 3 of 42 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn Contents 1 T E S T S T A N D A R D S ................................................................. 4 2 S U M M A R Y ............................................................................ 5 2.1 General Remarks 5 2.2 Product Description* 5 2.3 Equipment Under Test 5 2.4 Short description of the Equipment under Test (EUT) 5 2.5 EUT operation mode 6 2.6 Block Diagram of Test Setup 6 2.7 Related Submittal(s) / Grant (s) 6 2.8 Modifications 6 3 T E S T E N V I R O N M E N T .............................................................. 7 3.1 Address of the test laboratory 7 3.2 Test Facility 7 3.3 Environmental conditions 7 3.4 Summary of measurement results 8 3.5 Statement of the measurement uncertainty 8 3.6 Equipments Used during the Test 9 4 T E S T C O N D I T I O N S A N D R E S U L T S ........................................... 11 4.1 AC Power Conducted Emission 11 4.2 Radiated Emissions and Band Edge 14 4.3 Maximum Peak Output Power 21 4.4 Power Spectral Density 22 4.5 6dB Bandwidth 24 4.6 Out-of-band Emissions 26 4.7 Antenna Requirement 30 5 T E S T S E T U P P H O T O S O F T H E E U T ......................................... 31 6 P H O T O S O F T H E E U T ........................................................... 32 Report No.: CTA24022202601 Page 4 of 42 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn 1 T E S T S T A N D A R D S The tests were performed according to following standards: FCC Rules Part 15.247: Frequency Hopping, Direct Spread Spectrum and Hybrid Systems that are in operation within the bands of 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz. ANSI C63.10-2013: American National Standard for Testing Unlicensed Wireless Devices KDB558074 D01 V05r02: Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS) Operating Under §15.247 Report No.: CTA24022202601 Page 5 of 42 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, …

Text truncated - open the document above for the full version.

Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao‘an District, Shenzhen, China Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn FCC PART 15 SUBPART C TEST REPORT FCC PART 15.247 Report Reference No. ..................... : FCC ID............................................. : CTA24022202603 2BE9V-D6 Compiled by ( position+printed name+signature) . : File administrators Zoey Cao Supervised by ( position+printed name+signature) . : Project Engineer Amy Wen Approved by ( position+printed name+signature) . : RF Manager Eric Wang Date of issue .................................... : Mar. 02, 2024 Testing Laboratory Name .............. : Shenzhen CTA Testing Technology Co., Ltd. Address............................................ : Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao‘an District, Shenzhen, China Applicant’s name ............................ : Shenzhen Hongjie Chuang Technology Co. , Ltd Address ............................................ : Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen, China Test specification ........................... : Standard ........................................... : FCC Part 15.247 TRF Originator .................................. : Shenzhen CTA Testing Technology Co., Ltd. Shenzhen CTA Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTA Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTA Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description ..................... : Notebook computer Trade Mark ....................................... : N/A Manufacturer .................................... : Shenzhen Hongjie Chuang Technology Co. , Ltd Model/Type reference ...................... : D6 Listed Models .................................. : D7, D8, D9, E6, E7, E8, E9, Q6, Q7, Q8, Q9, T6, T7, TB, T9, Z6, Z7, Z8, Z9 Modulation Type ............................... : CCK/DSSS/OFDM Operation Frequency ........................ : From 2412 - 2462MHz Rating ............................................... : DC 7.7V From battery and DC 12.0V From external circuit Result ............................................... : PASS Report No.: CTA24022202603 Page 2 of 53 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn T E S T R E P O R T Equipment under Test : Notebook computer Model /Type : D6 Series Model No. D7, D8, D9, E6, E7, E8, E9, Q6, Q7, Q8, Q9, T6, T7, TB, T9, Z6, Z7, Z8, Z9 Applicant : Shenzhen Hongjie Chuang Technology Co. , Ltd Address : Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen, China Manufacturer : Shenzhen Hongjie Chuang Technology Co. , Ltd Address : Building A2, Wuhe Avenue and prospecting industrial zone, Bantian, Longgang District, Shenzhen, China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: CTA24022202603 Page 3 of 53 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn Contents 1 T E S T S T A N D A R D S ................................................................. 4 2 S U M M A R Y ............................................................................ 5 2.1 General Remarks 5 2.2 Product Description 5 2.3 Equipment Under Test 5 2.4 Short description of the Equipment under Test (EUT) 5 2.5 EUT operation mode 6 2.6 Block Diagram of Test Setup 6 2.7 Related Submittal(s) / Grant (s) 6 2.8 Modifications 6 3 T E S T E N V I R O N M E N T .............................................................. 7 3.1 Address of the test laboratory 7 3.2 Test Facility 7 3.3 Environmental conditions 7 3.4 Test Description 8 3.5 Statement of the measurement uncertainty 8 3.6 Equipments Used during the Test 9 4 T E S T C O N D I T I O N S A N D R E S U L T S ........................................... 11 4.1 AC Power Conducted Emission 11 4.2 Radiated Emission 14 4.3 Maximum Peak Conducted Output Power 20 4.4 Power Spectral Density 22 4.5 6dB Bandwidth 28 4.6 Out-of-band Emissions 34 4.7 Antenna Requirement 51 5 T E S T S E T U P P H O T O S O F T H E E U T ......................................... 52 6 P H O T O S O F T H E E U T ........................................................... 53 Report No.: CTA24022202603 Page 4 of 53 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn 1 T E S T S T A N D A R D S The tests were performed according to following standards: FCC Rules Part 15.247: Frequency Hopping, Direct Spread Spectrum and Hybrid Systems that are in operation within the bands of 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz. ANSI C63.10-2013: American National Standard for Testing Unlicensed Wireless Devices KDB558074 D01 v05r02: Guidance for Compliance Measurements on Digital Transmission Systems (DTS) ,Frequency Hopping Spread Spectrum System(HFSS), and Hybrid System D…

Text truncated - open the document above for the full version.

Report No.: CTA24022202603 Page 32 of 53 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn Ant2: 802.11b 802.11g CH01 CH01 CH06 CH06 CH11 CH11 Report No.: CTA24022202603 Page 33 of 53 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn 802.11n(HT20) 802.11n(HT40) CH01 CH03 / CH06 CH06 CH11 CH09 Report No.:…

Text truncated - open the document above for the full version.