
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
1. When the emitter is unable to remotely control the receiver ,please check whether the switch baterise are in good control.whether they are fixed properly and whether they run out of use. 2. when the emitter is unable to remotely control the receiver ,please check whether there is other remote control products around the space and check whether the keys are pressed down,because same nature of remote control product may cauxe interfercnce with each other resulting in poorreceiving effect.Taking away such articles will normalize the remote control function .(the infrated remote controller are not included). 3. Please use this product under applicable voltage.Too low voltage will lead to failure of the remote controller to work (Please refer to the product label for the voltage range and related parameters). 4. Please take out the batteries if you wull not use this product for a long time . The receiver wiring instructions Turn off the power supply before installation. WARNING: Notices BLACK: AC IN L WHITE: AC IN N PINKBROWN or :MOTOR-W GRAY:MOTOR-V RED:MOTOR-U BLUE:LIGHT L WHITE:LIGHT N 6 5 4 3 2 1 30 1H2H 4H8H FR Transmiter Instruction Digital matching Tips:The remote control has completed the learning pairing procedure before leaving the factory. After installation, it can be used directly. If you want to add or replace a new remote control, you need to pair it again. 360 ° Highly sensitive Signal can penetrate walls Omnidirectional control Remote contro ALL OFF Light:0n/0ff Forward rotating Natural wind Reversal reverse Fan:0n/0ff Fan speed control Fan speed reduced Fan speed increase Timed 30 minutes off 1 hour, 2 hours, 4 hours, 8 hours of timing Turn on the power while holding down the“1H + 4h” button, 3-5 seconds, release the“1H + 4H” button. Press any button, the fan can work normally, the code is completed. If not, please turn off the power once a minute in a repeat operation EMITTER Model:TX-19Ke-C Frequency: 433.92MHz Batteries: LR03-1.5V*2 Made in Chain Zhongshan Jinchai Yunhong Optoelelctronics TechnologyCo.,Ltd 30.00 mm 2 5 . 0 0 m m This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment The devices has been evaluated to meet general RF exposure requirement the device can be used in portable exposure condition without restriction
C5266091_X24_Ed.2 1/1 ZhongShan JinChaiYunHong Optoelectronic Technology Co., Ltd. “Attestation Statements” TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: ZhongShan JinChaiYunHong Optoelectronic Technology Co., Ltd. Grantee code: 2BEAV FCC ID: 2BEAVTX-19KE-C Contact Name: Toddy Tian Address: No.3, second floor, A block of Xihaiyi Road, Liexiyi community, Xiaolan town of zhongshan city, Guangdong, China. Telephone No: / Fax No: / Email: [email protected] i. [ZhongShan JinChaiYunHong Optoelectronic Technology Co., Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [ZhongShan JinChaiYunHong Optoelectronic Technology Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. [ZhongShan JinChaiYunHong Optoelectronic Technology Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [ is not] identified on the Covered List as an entity producing “covered”equipment . Date: 2024/01/03 Applicant’s Name: Toddy Tian Title: Manager Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist C5266091_X24_Ed.2 1/1
C5266091_X8_Ed.1 1/1 Letter of Authorization ZhongShan JinChaiYunHong Optoelectronic Technology Co., Ltd. Company: ZhongShan JinChaiYunHong Optoelectronic Technology Co., Ltd. Address: No.3, second floor, A block of Xihaiyi Road, Liexiyi community, Xiaolan town of zhongshan city, Guangdong, China. Product Name: Emitter Model Number: TX-19Ke-C FCC Identifier: 2BEAVTX-19KE-C We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Toddy Tian Date: 2024.1.04 Title: Manager Signature of applicant:
C5266091_X10_Ed.2 1/1 ZhongShan JinChaiYunHong Optoelectronic Technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2024-1-04 Subject: Request for Confidentiality FCC ID: 2BEAVTX-19KE-C To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. C5266091_X10_Ed.2 1/1 Sincerely, Signature: Name: Toddy Tian Title: Manager 2024.1.04
Page1of3ReportNo.:FCS202212157 Externalphotos Photo1 Photo2 Page2of3ReportNo.:FCS202212157 Photo3 Photo4 Page3of3ReportNo.:FCS202212157 Photo5 Photo6
LabelandLabelLocation FCCID:2BEAVTX-19KE-C
Page1of4ReportNo.:FCS202212157 Internalphotos Photo1 Photo2 Page2of4ReportNo.:FCS202212157 Photo3 PCBAntenna Photo4
Page1of2ReportNo.:FCS202212157 FluxComplianceServiceLaboratory Room105FloorBaohaoTechnologyBuilding1NO.15GongyeWestRoadHi-TechIndustrial,SongshanlakeDongguan Tel:769-27280901Fax:769-27280901http://www.FCS-lab.com FCCRFExposure EUTDescription:Emitter ModelNo.:TX-19Ke-C FCCID:2BEAVTX-19KE-C Equipmenttype:portabledevice AccordingtoKDB447498D01GeneralRFExposureGuidancev06andpart2.1093, UnlessspecificallyrequiredbythepublishedRFexposureKDBprocedures,standalone1-g headorbodyand10-gextremitySARevaluationforgeneralpopulationexposureconditions,by measurementornumericasimulation,isnotrequiredwhenthecorrespondingSARTest ExclusionThresholocondition(s),listedbelow.is(are)satisfied. For100MHzto6GHzandtestseparationdistances<50mm,the1-gand10-gSAR testexclusionthresholdsaredeterminedbythefollowing:(max.powerofchannel,including tune-uptolerance,mW)/(min.testseparationdistancemm)]·[vfGHz)]<3.0for1-gSAR,ands 7.5for10-gextremitySAR,wheref(GHz)istheRFchanneltransmitfrequencyinGHzPowerand distanceareroundedtothenearestmWandmmbeforecalculationTheresultisroundedtoone decimalplaceforcomparison 1.TestResultofRFExposureEvaluation EIRP=EMeas+20log(dmeas)-104.7 EIRPistheequivalentisotropicallyradiatedpower, E M easindBmisthefieldstrengthoftheemissionatthemeasurementdistance,indBuV/m dMeasisthemeasurementdistance,inm Field strength(dBuV/m) EIRP(dBm)Max tune-up(mW) Frequency(MHz)Min. distance(mm) Calc. thresholds limit -75.56-19.640.010864433.9250.00143.0 Conclusion:NoSARisrequired
AntennaSpecification Specification Specification WorkingFrequency433.92MHz GainDBi VSWR2.0max PolarizationLinear impedance50 azimuthbeamwidthOmni-directional OperationTemperature -40~+85 Manufacture's Name:ZhongShan JinChaiYunHong Optoelectronic Technology Co., Ltd. Address:No.3, second floor, A block of Xihaiyi Road, Liexiyi community, Xiaolan town of zhongshan city, Guangdong, China.
FluxComplianceServiceLaboratory Room105FloorBaohaoTechnologyBuilding1NO.15GongyeWestRoadHi-TechIndustrial,SongshanlakeDongguan Tel:769-27280901Fax:769-27280901http://www.FCS-lab.com FCCTestReport ReportNo:FCS202212157W01 Issuedfor Applicant: ZhongShanJinChaiYunHongOptoelectronic TechnologyCo.,Ltd. Address: No.3,secondfloor,AblockofXihaiyiRoad,Liexiyi community,Xiaolantownofzhongshancity, Guangdong,China. ProductName:Emitter BrandName:N/A ModelName:TX-19Ke-C SeriesModel:N/A FCCID:2BEAVTX-19KE-C IssuedBy:FluxComplianceServiceLaboratory Add:Room105FloorBaohaoTechnologyBuilding1NO.15GongyeWestRoadHi-Tech Industrial,SongshanlakeDongguan Tel:769-27280901Fax:769-27280901http://www.FCS-lab.com Page 2 of29ReportNo.:FCS202212157W01 FluxComplianceServiceLaboratory Room105FloorBaohaoTechnologyBuilding1NO.15GongyeWestRoadHi-TechIndustrial,SongshanlakeDongguan Tel:769-27280901Fax:769-27280901http://www.FCS-lab.com TESTRESULTCERTIFICATION Applicant’sName......................: ZhongShanJinChaiYunHongOptoelectronicTechnology Co.,Ltd. Address......................................: No.3,secondfloor,AblockofXihaiyiRoad,Liexiyi community,Xiaolantownofzhongshancity,Guangdong, China. Manufacture'sName................: ZhongShanJinChaiYunHongOptoelectronicTechnology Co.,Ltd. Address......................................: No.3,secondfloor,AblockofXihaiyiRoad,Liexiyi community,Xiaolantownofzhongshancity,Guangdong, China. ProductDescription ProductName...........................: Emitter BrandName ............................. : N/A ModelName..............................: TX-19Ke-C SeriesModel .............................. : N/A TestStandards..........................:FCCRulesandRegulationsPart15SubpartC,Section231 TestProcedure..........................:ANSIC63.10:2013 ThisdevicedescribedabovehasbeentestedFCS,thetestresultsshowthattheequipmentunder test(EUT)isincompliancewiththeFCCrequirements.Anditisapplicableonlytothetestedsample identifiedinthereport. Thisreportshallnotbereproducedexceptinfull,withoutthewrittenapprovalofFCS,thisdocument maybealteredorrevisedbyFCS,personalonly,andshallbenotedintherevisionofthedocument.. DateofTest..................................: Date(s)ofperformanceoftests . :Jun28,2022~Jan3,2023 DateofIssue ................................. :Jan3,2023 TestResult....................................:Pass Testedby: (ScottShen) Reviewedby : (DukeQian) Approvedby: (JackWang) Page 3 of29ReportNo.:FCS202212157W01 FluxComplianceServiceLaboratory Room105FloorBaohaoTechnologyBuilding1NO.15GongyeWestRoadHi-TechIndustrial,SongshanlakeDongguan Tel:769-27280901Fax:769-27280901http://www.FCS-lab.com TableofContentsPage 1.SUMMARYOFTESTRESULTS............................................................................................6 1.1TESTFACTORY..............................................................................................................7 1.2MEASUREMENTUNCERTAINTY...................................................................................7 2.GENERALINFORMATION.....................................................................................................8 2.1GENERALDESCRIPTIONOFTHEEUT.........................................................................8 2.2DESCRIPTIONOFTHETESTMODES...........................................................................9 2.3DESCRIPTIONOFNECESSARYACCESSORIESANDSUPPORTUNITS.................10 2.4EQUIPMENTSLIST.......................................................................................................11 3CONDUCTEDEMISSIONMEASUREMENT..........................................................................12 3.1LIMIT..............................................................................................................................12 3.2TESTPROCEDURE......................................................................................................12 3.3TESTSETUP.................................................................................................................13 3.4TESTRESULTS.............................................................................................................14 4.RADIATEDEMISSIONMEASUREMENT.............................................................................15 4.1LIMIT..............................................................................................................................15 4.2TESTPROCEDURE......................................................................................................16 4.3TESTSETUP.................................................................................................................17 4.4TESTRESULTS.............................................................................................................18 Forfieldstrengthofthefundamentalsignal..........................................................................18 (30MHZ-1000MHZ)..............................................................................................................19 5.TRANSMITTERTIME...........................................................................................................22 5.1LIMIT..............................................................................................................................22 5.2TESTPROCEDURE......................................................................................................22 5.3TESTSETUP.................................................................................................................22 5.4TESTRESULTS.............................................................................................................22 6.20DBBANDWIDTHTEST...................................................................................................23 6.1LIMIT..............................................................................................................................23 6.2TESTPROCEDURE...........................................................................…
Text truncated - open the document above for the full version.
Page 1 of1ReportNo.:FCS202212157 Blow1GHzforradiatedemissiontestsetup Above1GHzforradiatedemissiontestsetup
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15.231 | 433.92 MHz - 433.92 MHz | - |