2BEEO-J2005Bluetooth speaker

Right Speaker Built-in Bluetooth Amplifier Sound Bar Instruction Manual Model: J2005-4 Qualified Design ID: 180349 2. Specifications 1. Product Outview 4. Important Safety & Usage Notes Left Speaker 12V / 2A Power Adapter 3. Installation & Operating Instructions •Bluetooth Version: 5.3 + EDR Enhanced •Wireless Range: Within an effective distance of 10 meters (33 feet) •Output Power: 10 W + 10 W (RMS) •Rated Impedance: 8 Ω •Speaker Units: ▪Left: 2" x 2 (5 W / 8 Ω each) ▪Right: 2" x 2 (5 W / 8 Ω each) •Frequency Response: 25 Hz - 20 kHz •Sign-to-Noise Ratio: ≥ 90 dB •Channel Separation: ≥ 85 dB •Power Adapter Input: 100-240 V AC ~ 50/60 Hz •Power Output: 12 V DC 2A •Sound Bar Size (each) : 65 W * 50 D * 430 H mm (2 pcs) •Bluetooth Name: fireplace speaker 1.Connect the DC plug from the power adapter to the DC input jack located on the back of the right speaker. 2.Plug the power adapter into a suitable wall outlet. 3.Enable Bluetooth on your mobile device, TV, or other compatible device. 4.Search for "fireplace speaker" and select it to pair. 5.Once connected, audio will play through the speaker. •This unit can only pair and connect to one Bluetooth device at a time. Disconnect the current device before pairing a new one. •For indoor use only. Keep in a dry, well-ventilated environment. •Use only the supplied 12 V DC power adapter. Using a higher voltage may damage the product FCC / ICES Complinace Statement CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm (8 inches) between the radiator and your body. ICES Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: 1.This device may not cause interference. 2.This device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Page 1 of 6 Report No.: LGT26E097 Appendix - External Photographs of EUT Constructional Details Photo 1(Model: J2005-2) Photo 2(Model: J2005-4) Page 2 of 6 Report No.: LGT26E097 Appendix - External Photographs of EUT Constructional Details Photo 3 Photo 4 Page 3 of 6 Report No.: LGT26E097 Appendix - External Photographs of EUT Constructional Details Photo 5 Photo 6 Page 4 of 6 Report No.: LGT26E097 Appendix - External Photographs of EUT Constructional Details Photo 7 Photo 8 Page 5 of 6 Report No.: LGT26E097 Appendix - External Photographs of EUT Constructional Details Photo 9 Photo 10 Page 6 of 6 Report No.: LGT26E097 Appendix - External Photographs of EUT Constructional Details Photo 11

Label Size: 21*52mm

Page 1 of 3 Report No.: LGT26E097 Appendix - Internal Photographs of EUT Constructional Details Photo 1 Photo 2 Page 2 of 3 Report No.: LGT26E097 Appendix - Internal Photographs of EUT Constructional Details Photo 3 Photo 4 ANT Page 3 of 3 Report No.: LGT26E097 Appendix - Internal Photographs of EUT Constructional Details Photo 5

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Page 1 of 8 EMF TEST REPORT Product Name: Bluetooth Speaker Model Number: J2005-4, J2005-2 FCC ID: 2BEEO-J2005 Issued For : Dongguan Jin wen hua digital technology Co.,LTD NO.1 hua Da Road,Long Bei Ling Village,Tangxia Town,Dongguan City,Guangdong,china Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT26E097HA01 Sample Received Date: May 15, 2026 Date of Test: May 15, 2026 ~ May 29, 2026 Date of Issue: May 29, 2026 Report No.: LGT26E097HA01 Page 2 of 8 TEST REPORT CERTIFICATION Applicant: Dong guan City Huge Sun Lighting Co.,LTD Address: Room 301, Building 1, No. 6, Sangyuan Yinyang Road, Dongcheng Street, Dongguan City, Guangdong Province, China Manufacturer: Dong guan City Huge Sun Lighting Co.,LTD Address: Room 301, Building 1, No. 6, Sangyuan Yinyang Road, Dongcheng Street, Dongguan City, Guangdong Province, China Product Name: Bluetooth Speaker Trademark: Huge Sun Model Number: J2005-4, J2005-2 Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC 47 CFR §2.1091 KDB 447498 D01 General RF Exposure Guidance v06 PASS Prepared by: Approved by: Chris Chen Vita Li Engineer Technical Director Report No.: LGT26E097HA01 Page 3 of 8 TABLE OF CONTENTS 1 . GENERAL INFORMATION 5 1.1 GENERAL DESCRIPTION OF THE EUT 5 1.2 TEST LABORATORY 5 2 . FCC 47CFR §2.1091 REQUIREMENT 6 2.1 TEST STANDARDS 6 2.2 LIMIT 6 2.3 EUT OPERATION CONDITION 7 2.4 CLASSIFICATION 7 2.5 TEST RESULT 8 Report No.: LGT26E097HA01 Page 4 of 8 Revision History Rev. Issue Date Revisions 00 May 29, 2026 Initial Issue Report No.: LGT26E097HA01 Page 5 of 8 1. GENERAL INFORMATION 1.1 GENERAL DESCRIPTION OF THE EUT Product Name: Bluetooth Speaker Test Model Number: J2005-4 Series Number: J2005-2 Model Difference: The quantity of speakers and power adapters are different (Model J2005-4 with two speakers and a 12V/2A power supply; Model J2005-2 is equipped with one speaker and a 12V/1A power supply). Bluetooth: Frequency:2402 – 2480 MHz Modulation: GFSK(1Mbps), π/4-DQPSK(2Mbps), 8DPSK(3Mbps) Antenna Type: PCB Antenna Antenna Gain: 2.04dBi Rating: 12V/2A (J2005-4) 12V/1A (J2005-2) Battery: N/A Hardware Version: N/A Software Version: N/A Connecting I/O Port(s): Please refer to the Note 1. 1.2 TEST LABORATORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate: FCC Registration No.: 746540 CAB ID: CN0136 Report No.: LGT26E097HA01 Page 6 of 8 2. FCC 47CFR §2.1091 REQUIREMENT 2.1 TEST STANDARDS The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The gain of the antennas used in the product is extracted from the Antenna data sheets provided and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis Transmission formula is far field assumption, the calculated result of that is an over-prediction for near field power density. It is taken as worst case to specify the safety range. 2.2 LIMIT According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of the human exposure to radio-frequency (RF) radiation as specified in 1.1307 (b) Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm²) Limits for Occupational / controlled Exposures 0.3-3.0 614 1.63 *(100) 3.0-30 1842/f 4.89/f *(900/f 2 ) 30-300 61.4 0.163 1.0 300 - 1500 -- -- F/300 1500 – 100000 -- -- 5.0 Limits for General population / Uncontrolled Exposure 0.3-1.34 614 1.63 *(100) 1.34-30 824/f 2.19/f *(180/f 2 ) 30-300 27.5 0.073 0.2 300 - 1500 -- -- F/1500 1500 – 100000 -- -- 1.0 F= Frequency in MHz * = Plane-wave equivalent power density. Friss Formula Friss Transmission Formula: Pd = (Pout * G) / (4*pi*r²) Where Pd = power density in mW/cm² Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = Distance between observation point and the center of radiator in cm If we know the maximum gain of the antenna and the total output power to the antenna, through calculation, we will know MPE value at distance 20cm. Report No.: LGT26E097HA01 Page 7 of 8 2.3 EUT OPERATION CONDITION EUT was enabled to transmit and receive at lowest, middle and highest channels. 2.4 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. Warning statement to the user for keeping at least 20cm or more separation distance from the antenna should be included in the User manual. So, this device is classified as Mobile device. Report No.: LGT26E097HA01 Page 8 of 8 2.5 TEST RESULT Turn up Result Mode Turn up Power BT-GFSK 3.5±1dBm BT-π/4-DQPSK 3±1dBm BT-8DPSK 3±1dBm The MPE result of worst mode: RF Function Max Turn up Power (dBm) Max Turn up Power (mW) ANT Gain (dBi) ANT Gain (gain of antenna in linear scale) Power Density (mW/cm²) Limit (mW/cm²) Ratio Result BT 4.50 2.82 2.04 1.60 0.001 1 0.001 Pass Note: 1. The RF Exposure is less than the limit, complies with the exemption requirements. ※※※※※END OF THE REPOR…

Text truncated - open the document above for the full version.

2.04dBi product model name_antenna model name_PCB Antenna Test Equipment:XXXX 1. Electrical Characteristics No. Item Specifications 1 Working Central Frequency 2450 MHz 2 Band Width 3 Gain 4 V.S.W.R (in BW) ≤2.0 5 Polarization Linear 6 Azimuth Beam width Omni-directional 7 Impedance 阻抗 50  2400~2500MHZ Antenna Type: PCB Antenna Manufacturer: Dong guan City Huge Sun Lighting Co.,LTD Address: Room 301, Building 1, No. 6, Sangyuan Yinyang Road, Dongcheng Street, Dongguan City, Guangdong Province, China 2.Return Loss and Smith Chat - 40 - 35 - 30 - 25 - 20 - 15 - 10 - 5 0 2 000 2 100 2 200 2 300 2 400 2 500 2 600 2 700 2 800 2 900 3 000 M 1 M 2 M 3 M 4 R eturn Loss C urrent Model: S332D Serial #: 00924093 Date: Sep/02/2009 Time: 14:16:43 Std: --- Channel: N/A Resolution: 517 FlexCAL:ON(COAX) CW: ON dB F requency (2000.0 - 3000.0 MHz) M 1: -12.90 dB @ 2397.387 MHz M 2: -19.64 dB @ 2451.550 MHz M 3: -15.75 dB @ 2482.658 MHz M 4: -.28 dB @ 2000.100 MHz 3． ．． ．Physical Test Environment Antitsu S332D 0.2 0.4 0.6 0.8 1 1.5 2 3 4 5 10 20 50 0.2 0.4 0.6 0.8 1 1.5 2 3 4 5 10 20 50 -0.2 -0.4 -0.6 -0.8 -1 -1.5 -2 -3 -4 -5 -10 -20 -50 M1 M2 M3 M4 Smith Chart Current Model: S332D Serial #: 00924093 Date: Sep/02/2009 Time: 14:16:43 Prop.Vel:.800 Resolution: 517 FlexCAL:ON(COAX) CW ON M1: r=1.48, x=0.30 @ 2397.387 MHz M2: r=1.02, x=-0.21 @ 2451.65 MHz M3: r=0.75, x=-0.14 @ 2482.658 MHz M4: r=0.02, x=0.43 @ 2000.10 MHz 4.Shape of the antenna 5 Radiation Pattern 0.66 END

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Page 1 of 75 RF TEST REPORT Product Name: Bluetooth Speaker Model Number: J2005-4, J2005-2 FCC ID: 2BEEO-J2005 Issued For : Dong guan City Huge Sun Lighting Co.,LTD Room 301, Building 1, No. 6, Sangyuan Yinyang Road, Dongcheng Street, Dongguan City, Guangdong Province, China Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guan gdong, China Report Number: LGT26E097RF01 Sample Received Date: May 15, 2026 Date of Test: May 15, 2026 ~ May 29, 2026 Date of Issue: May 29, 2026 Report No.: LGT26E097RF01 Pa ge 2 of 75 TEST REPORT CERTIFICATION Applicant: Dong guan City Huge Sun Lighting Co.,LTD Address: Room 301, Building 1, No. 6, Sangyuan Yinyang Road, Dongcheng Street, Dongguan City, Guangdong Province, China Manufacturer: Dong guan City Huge Sun Lighting Co.,LTD Address: Room 301, Building 1, No. 6, Sangyuan Yinyang Road, Dongcheng Street, Dongguan City, Guangdong Province, China Product Name: Bluetooth Speaker Trademark: Huge Sun Model Number: J2005-4, J2005-2 Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC Part 15.247, Subpart C ANSI C63.10-2020 + Cor.1-2023 PASS Prepared by: Approved by: Chris Chen Vita Li Engineer Technical Director Report No.: LGT26E097RF01 Pa ge 3 of 75 Table of Contents Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST LABORATORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 10 2.3 FREQUENCY HOPPING SYSTEM REQUIREMENTS 10 2.4 TABLE OF PARAMETERS OF TEST SOFTWARE SETTING 12 2.5 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 12 2.6 EQUIPMENTS LIST 13 3. EMC EMISSION TEST 15 3.1 CONDUCTED EMISSION MEASUREMENT 15 3.2 RADIATED EMISSION MEASUREMENT 21 4.6 TEST RESULTS (BAND EDGE REQUIREMENTS) 31 4. CONDUCTED SPURIOUS & BAND EDGE EMISSION 32 4.1 LIMIT 32 4.2 TEST PROCEDURE 32 4.3 TEST SETUP 32 4.4 EUT OPERATION CONDITIONS 33 4.5 TEST RESULTS 33 5. NUMBER OF HOPPING CHANNEL 34 5.1 LIMIT 34 5.2 TEST PROCEDURE 34 5.3 TEST SETUP 34 5.4 EUT OPERATION CONDITIONS 34 5.5 TEST RESULTS 34 6. AVERAGE TIME OF OCCUPANCY 35 6.1 LIMIT 35 6.2 TEST PROCEDURE 35 6.3 TEST SETUP 35 6.4 EUT OPERATION CONDITIONS 35 6.5 TEST RESULTS 35 7. HOPPING CHANNEL SEPARATION MEASUREMEN 36 Report No.: LGT26E097RF01 Pa ge 4 of 75 7.1 LIMIT 36 7.2 TEST PROCEDURE 36 7.3 TEST SETUP 36 7.4 EUT OPERATION CONDITIONS 36 7.5 TEST RESULTS 36 8. BANDWIDTH TEST 37 8.1 LIMIT 37 8.2 TEST PROCEDURE 37 8.3 TEST SETUP 37 8.4 EUT OPERATION CONDITIONS 37 8.5 TEST RESULTS 37 9. OUTPUT POWER TEST 38 9.1 LIMIT 38 9.2 TEST PROCEDURE 38 9.3 TEST SETUP 38 9.4 EUT OPERATION CONDITIONS 38 9.5 TEST RESULTS 38 10. ANTENNA REQUIREMENT 39 10.1 STANDARD REQUIREMENT 39 10.2 EUT ANTENNA 39 APPENDIX I - TEST RESULTS 40 1. DUTY CYCLE 40 2. BANDWIDTH 44 3. MAXIMUM CONDUCTED OUTPUT POWER 51 4. CARRIER FREQUENCY SEPARATION 55 5. NUMBER OF HOPPING FREQUENCIES 57 6. TIME OF OCCUPANCY (DWELL TIME) 59 7. UNWANTED EMISSIONS IN NON-RESTRICTED FREQUENCY BANDS 62 APPENDIX II - MEASUREMENT PHOTOS 75 Report No.: LGT26E097RF01 Pa ge 5 of 75 Revision History Rev. Issue Date Revisions 00 May 29, 2026 Initial Issue Report No.: LGT26E097RF01 Pa ge 6 of 75 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 15.247 Meas Guidance v05r02. FCC Part 15.247, Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS -- 15.247(a)(1) Hopping Channel Separation PASS -- 15.247(a)(1)&(b)(1) Output Power PASS -- 15.209 Radiated Spurious Emission PASS -- 15.247(d) Conducted Spurious & Band Edge Emission PASS -- 15.247(a)(1)(iii) Number of Hopping Frequency PASS -- 15.247(a)(1)(iii) Dwell Time PASS -- 15.247(a)(1) Bandwidth PASS -- 15.205 Restricted bands of operation PASS -- Part 15.247(d)/part 15.209(a) Band Edge Emission PASS -- 15.203 Antenna Requirement PASS -- NOTE: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2020 + Cor.1-2023. Report No.: LGT26E097RF01 Pa ge 7 of 75 1.1 TEST LABORATORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate: FCC Registration No.: 746540 CAB ID: CN0136 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 Occupied Channel Bandwidth ±0.46% 2 RF Output Power, Conducted ±0.71dB 3 Power Spectral Density, Conducted ±1.57dB 4 Unwanted Emission, Conducted ±0.63dB 5 Conducted emission ±2.80dB 6 All Emissions, Radiated (0.009-30MHz) ±2.16dB 7 All Emissions, Radiated (30MHz-1GHz) ±4.61dB 8 All Emissions, Radiated (1GHz-18GHz) ±5.49dB 9 Temperature ±0.5°C 10 Humidity ±2% 11 Duty Cycle ±2.3% Note: The measurement uncertainty is not included in the test result. Report No.: LGT26E097RF01 Pa ge 8 of 75 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name: Bluetooth Speaker Test Model Number: J2005-4 Series Number: J2005-2 Model Difference: The quantity of speakers and power adapters are different (Model J2005-4 with two speakers and a 12V/2A power supply; Model J2005-2 is equipped with one speaker and a 12V/1A po…

Text truncated - open the document above for the full version.

Page 1 of 2 Report No.: LGT26E097 Appendix - Test Setup photos Set-up for Radiated Spurious Emission, Below 1GHz Set-up for Radiated Spurious Emission, Above 1GHz Page 2 of 2 Report No.: LGT26E097 Set-up for Conducted Emission