2BEHH-C1-01Treadmill

FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarant ee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environm ent. This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter.

WUYIYULEPLASTICCO.,LTD 03-28-2024 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(i)requestfor(FCCID:2BEHH-C1-01) [WUYIYULEPLASTICCO.,LTD](“theapplicant”)certifiesthattheequipmentforwhich authorizationissoughtisnot“covered”equipmentprohibitedfromreceivingan equipmentauthorizationpursuanttosection2.903oftheFCCrules. Sincerely, ChenYajun WUYIYULEPLASTICCO.,LTD 03-26-2024 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(ii)requestfor(FCCID:2BEHH-C1-01) [WUYIYULEPLASTICCO.,LTD](“theapplicant”)certifiesthat,asofthedateofthefiling oftheapplication,theapplicantisnotidentifiedontheCoveredListasanentity producing“covered”equipment. Sincerely, ChenYajun

WUYIYULEPLASTICCO.,LTD AgentAuthorizationLetter 2023-03-28 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 USA RE:LETTEROFAGENTAUTHORIZATION ToWhomItMayConcern: We,theundersigned,herebyauthorizeShenzhenMostTechnologyServiceCo.,Ltd.toact onourbehalfinallmattersrelatingtoapplicationforequipmentauthorization,includingthe signingofalldocumentsrelatingtothesematters. Wealsoherebycertifythatnopartytotheapplicationauthorizedhereunderissubjecttothe denialofbenefits,includingFCCbenefits,pursuanttoSection5301oftheAnti-DrugAbuse Actof1988,21U.S.C.853(a). Thisagreementexpiresoneyearfromthecurrentdate. Sincerely, Name: ChenYajun Position:Manager CompanyName:WUYIYULEPLASTICCO.,LTD Address:LongshengXiaoweiGarden,No.11BaiheRoad,BaiyangStreet,Wuyi County,Jinhua,Zhejiang Tel/Fax 13566938313 E-Mail:[email protected]

WUYIYULEPLASTICCO.,LTD LongTermConfidentialityRequestLetter 2024-03-28 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 USA RE:CONFIDENTIALITYREQUESTFOR(FCCID:2BEHH-C1-01) ToWhomItMayConcern: Thisletterservesasanofficialrequestforconfidentialityundersections0.457and0.459of CFR47.Wehaverequestedthatthe -e.g.Blockdiagram -e.g.SCH -e.g.OperationalDescription requiredtobesubmittedwiththisapplicationbepermanentlywithheldfrompublicreview. Theabovedocumentsarecompanyproprietaryinformationthatcouldnevergetinto thepossessionofyourcompetition. Pleasecontactmeifthereisanyinformationyoumayneed. Sincerely, Name: ChenYajun Position:Manager CompanyName:WUYIYULEPLASTICCO.,LTD Address:LongshengXiaoweiGarden,No.11BaiheRoad,BaiyangStreet,Wuyi County,Jinhua,Zhejiang Tel/Fax 13566938313 E-Mail:[email protected]

Modeldifferenceletter 2024.03.28 OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA ThisisanewApplicationfromJinhuaZhuoliElectronicCommerceCo.,Ltd ModelNo.: C1-01,C1 OnlythemodelC1-01wastested,Theirelectricalcircuitdesign,layout, componentsusedandinternalwiringareidentical,Onlythemodelnameis different. Yourssincerely, Signatory: Sincerely, Signature: Name:ChenYajun Title:Manager

Model No.: C1-01 FRONT VIEW OF SAMPLE BACK VIEW OF SAMPLE Model No.: C1-01 LEFT VIEW OF SAMPLE RIGHT VIEW OF SAMPLE Model No.: C1-01 TOP VIEW OF SAMPLE BOTTOM VIEW OF SAMPLE Model No.: C1-01

FCCID:2BEHH-C1-01

Model No.: C1-01 Page 1 of 2 INTERNAL PHOTO OF SAMPLE INTERNAL PHOTO OF SAMPLE PCB antenna Model No.: C1-01 Page 2 of 2

Shenzhen Most Technology Service Co., Ltd. No.5, 2nd Langshan Road, North District, Hi-tech Industrial Park, Nanshan, Shenzhen, Guangdong, China. TEST REPORT Report Reference No. ..................... : FCC ID.. ........................................... : MTEB24010064-H 2BEHH-C1-01 Compiled by ( position+printed name+signature) .. : File administrators Alisa Luo Supervised by ( position+printed name+signature) .. : Test Engineer Sunny Deng Approved by ( position+printed name+signature) .. : Manager Yvette Zhou Date of issue ..................................... : Jan. 08,2024 Representative Laboratory Name .: Shenzhen Most Technology Service Co., Ltd. Address ............................................ : No.5, 2nd Langshan Road, North District, Hi-tech Industrial Park, Nanshan, Shenzhen, Guangdong, China. Applicant’s name ............................ : WUYI YULE PLASTIC CO., LTD Address ............................................ : Longsheng Xiaowei Garden, No. 11 Baihe Road, Baiyang Street, Wuyi County, Jinhua, Zhejiang Test specification/ Standard ..........: 47 CFR Part 1.1307 47 CFR Part 2.1093 TRF Originator .................................. : Shenzhen Most Technology Service Co., Ltd. Shenzhen Most Technology Service Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Most Technology Service Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Most Technology Service Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: Treadmill Trade Mark ....................................... : N/A Model/Type reference....................... : C1-01 Listed Models .................................. : C1 Modulation Type ............................... : FSK Operation Frequency ........................ : 433.92MHz Hardware version ............................. : Software version .............................. : Rating ............................................... : LXZK-RF1208 V1.0 TX4K30_23122_020 DC 3V by Battery Result................................................ : PASS Report No.: MTEB24010064-H Page 2 of 5 T E S T R E P O R T Equipment under Test : Treadmill Model /Type : C1-01 Listed Models : C1 Remark C 1 has no armrest, c 1-01 has armrest, everything else is the same Applicant : WUYI YULE PLASTIC CO., LTD Address : Longsheng Xiaowei Garden, No. 11 Baihe Road, Baiyang Street, Wuyi County, Jinhua, Zhejiang Manufacturer : WUYI YULE PLASTIC CO., LTD Address : Longsheng Xiaowei Garden, No. 11 Baihe Road, Baiyang Street, Wuyi County, Jinhua, Zhejiang Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: MTEB24010064-H Page 3 of 5 Contents 1. R e v i s i o n H i s t o r y Revision Issue Date Revisions Revised By 00 2024.01.08 Initial Issue Alisa Luo Report No.: MTEB24010064-H Page 4 of 5 2.1 RF Exposure Compliance Requirement 2.1.1 Standard Requirement According to KDB447498D01 General RF Exposure Guidance v06 4.3.1. Standalone SAR test exclusion considerations Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Exclusion Threshold condition, listed below, is satisfied. 2.1.2 Limits The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation17 The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion Report No.: MTEB24010064-H Page 5 of 5 2.1.3 EUT RF Exposure EIRP =PT*GT= (E x D)²/30 where: PT = transmitter output power in watts, GT = numeric gain of the transmitting antenna (unitless), E = electric field strength in V/m, ---10 (dBμV/m)/20) /10 6 , D = measurement distance in meters (m)---3m, So PT = (E x D)²/30 / GT The worst case (refer to report MTEB24010064-R) is below: Antenna polarization: Horizontal Frequency (MHz) Level (dBuV/m) Polarization 433.92 75.56 Peak 433.92 50.71 Average Antenna polarization: Vertical Frequency (MHz) Level (dBuV/m) Polarization 433.92 76.75 Peak 433.92 50.66 Average For 433.92MHz wireless: Field strength=76.75dBuV/m Ant gain 0.7dBi;so Ant numeric gain=1.17 EIRP = PT*GT = (E x D)²/30=(10 (dBμV/m)/20) /10 6 *3) 2 /30=0.000014 So PT= EIRP/GT=0.000014W=0.014mW So(0.014mW/5mm)* √0.43392GHz=0.0018 exclusion=0.0018<3.0 for 1-g SAR So the SAR report is not required.

ShenzhenMostTechnologyServiceCo.,Ltd. No.5,2ndLangshanRoad,NorthDistrict,Hi-techIndustrialPark,Nanshan, Shenzhen,Guangdong,China. TESTREPORT FCCRulesPart15.231 ReportReferenceNo........................: FCCID.................................................: MTEB24010064-R 2BEHH-C1-01 Compiledby (position+printedname+signature)..:FileadministratorsAlisaLuo Supervisedby (position+printedname+signature)..:TestEngineerSunnyDeng Approvedby (position+printedname+signature) .. : ManagerYvetteZhou Dateofissue ......................................... :Jan.08,2024 RepresentativeLaboratoryName.:ShenzhenMostTechnologyServiceCo.,Ltd. Address.................................................: No.5,2ndLangshanRoad,NorthDistrict,Hi-techIndustrialPark, Nanshan,Shenzhen,Guangdong,China. Applicant’sname ............................... :WUYIYULEPLASTICCO.,LTD Address.................................................: LongshengXiaoweiGarden,No.11BaiheRoad,BaiyangStreet, WuyiCounty,Jinhua,Zhejiang Testspecification/Standard............: FCCPart15SubpartC,Section15.231 TRFOriginator ...................................... :ShenzhenMostTechnologyServiceCo.,Ltd. ShenzhenMostTechnologyServiceCo.,Ltd.Allrightsreserved. Thispublicationmaybereproducedinwholeorinpartfornon-commercialpurposesaslongasthe ShenzhenMostTechnologyServiceCo.,Ltd.isacknowledgedascopyrightownerandsourceofthe material.ShenzhenMostTechnologyServiceCo.,Ltd.takesnoresponsibilityforandwillnotassume liabilityfordamagesresultingfromthereader'sinterpretationofthereproducedmaterialduetoits placementandcontext. Testitemdescription ........................ :Treadmill TradeMark............................................: N/A Model/Typereference ......................... :C1-01 ListedModels......................................:C1 ModulationType..................................: FSK OperationFrequency..........................: 433.92MHz Hardwareversion.................................: Softwareversion.................................: Rating.....................................................: LXZK-RF1208V1.0 TX4K30_23122_020 DC3VbyBattery Result ..................................................... :PASS ReportNo.:MTEB24010064-RPage 2 of 24 TESTREPORT EquipmentunderTest:Treadmill Model/Type:C1-01 ListedModels: C1 RemarkC1hasnoarmrest,c1-01hasarmrest,everythingelseisthe same Applicant: WUYIYULEPLASTICCO.,LTD Address: LongshengXiaoweiGarden,No.11BaiheRoad,BaiyangStreet, WuyiCounty,Jinhua,Zhejiang Manufacturer: WUYIYULEPLASTICCO.,LTD Address: LongshengXiaoweiGarden,No.11BaiheRoad,BaiyangStreet, WuyiCounty,Jinhua,Zhejiang TestResult : PASS Thetestreportmerelycorrespondstothetestsample. Itisnotpermittedtocopyextractsofthesetestresultwithoutthewrittenpermissionofthetest laboratory. ReportNo.:MTEB24010064-RPage 3 of 24 Contents 1.REVISIONHISTORY.........................................................................................................................4 2.TESTSTANDARDS............................................................................................................................5 3.SUMMARY...............................................................................................................................................6 3.1.GeneralRemarks.........................................................................................................................................6 3.2.ProductDescription....................................................................................................................................6 3.3.EquipmentUnderTest................................................................................................................................6 3.4.ShortdescriptionoftheEquipmentunderTest(EUT)............................................................................6 3.5.EUToperationmode....................................................................................................................................6 3.6.BlockDiagramofTestSetup......................................................................................................................6 3.7.TestItem(EquipmentUnderTest)Description*.......................................................................................7 3.8.AuxiliaryEquipment(AE)Description.......................................................................................................7 3.9AntennaInformation*...................................................................................................................................7 3.10.EUTconfiguration......................................................................................................................................7 3.11.Modifications..............................................................................................................................................7 4.TESTENVIRONMENT.......................................................................................................................8 4.1.Addressofthetestlaboratory...................................................................................................................8 4.2.Environmentalconditions...........................................................................................................................8 4.3.TestDescription...........................................................................................................................................9 4.4.Statementofthemeasurementuncertainty.............................................................................................9 4.5.EquipmentsUsedduringtheTest...........................................................................................................10 5.TESTCONDITIONSANDRESULTS.....................................................................................11 5.1.ACPowerConductedEmission....................................................................................................1…

Text truncated - open the document above for the full version.

InvertedFAntennaspecification Summary ITEMANTSPEC ResonateFrequency 433.92MHZANT 天线增益Antennagain 0.7dBi 驻波比VSWR/50Ohm 1.5orless 方向图Radiationpatt全向(Omnidirectio) 极化方式Polarization HorizontalandVertical Impedance 500hm AntennaLength 78.150MM AntennaPhoto&Length(mm) AboutXaxis AboutZaxis 180 AboutYaxis

ModelNo.:C1-01 RETESTSETUP RETESTSETUP ModelNo.:C1-01