2BF27E1Laser Engraving Machine

Sculpfun E1 Series User Manual V1.0 FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. CE Frequency and power 2412-2472MHzMHz（14.11 dBm） Manufacturer Shenzhen Sculpfun Technology Co., Ltd. Room 401, Building 13, No. 140, Guanlan Avenue, Sihe Community, Fucheng Street, Longhua District, Shenzhen City, China 01 Operation Guide 1 Product Assembly Follow the assembly instructions in this manual to assemble the product. You can also watch the step-by-step assembly video at: https://wiki.sculpfun.com/ 6 Place the Material Place the material to be engraved within the machine’s working area. 2 Download and install the CH340 driver and engraving software (Sculpfun Space / LightBurn). You can also scan the QR code to download them directly, or visit the Wiki to access the software. Software Installation 7 Laser Focusing Lower the focusing lever on the laser head. Adjust the height of the laser head until the lever touches the surface of the material, then raise the focusing lever back into place. 3 Connect to Computer Connect the engraving machine to your computer using the USB cable, then launch the engraving software. 8 Positioning After completing the setup, use the Frame function in the software to preview and confirm the the position of the design and material. 4 Import Engraving Image Import the image you want to engrave. A higher-quality image will produce better engraving results. 9 Close the Lid Once the position is confirmed, close the. The machine will not start engraving unless the lid is closed. 5 Set Parameters Adjust the engraving parameters in the software. You can scan the QR code or visit the Wiki to access the recommended material parameter settings. 10 Start Engraving After closing the lid, click Start in the software to begin the engraving process. 01 APP 02 Scan the QR code to access the E1 related software and information On your phone, connect to the E1 network. Default password: 12345678 Open the app and tap ‘Connected’ Download the Sculpfun App Google play App store Enter the IP address 192.168.4.1 and tap Connect. You can now control the engraving machine from your phone. 03 Thank You Letter! Dear User, Thank you for choosing Sculpfun. We hope our product helps you bring your ideas to life and create projects you truly enjoy. You can follow Sculpfun on social media platforms such as Facebook, Instagram, and TikTok. There you can share your creations, discover new ideas, and find inspiration from other creators to explore even more possibilities. The Sculpfun Team is always ready to provide you with reliable support. If you encounter any issues during use, please contact us via the email address provided in this manual. For more instructions and tutorial videos, please visit our Wiki: https://wiki.sculpfun.com/ Table of Contents 04 1. Safety Instructions 2. Packing List 3. Assembly Steps 4. Laser Module Removal & Installation 5. Product Structure 6. Product Specifications 7. Operating Instructions 8. Maintenance 9. Troubleshooting - - - - - - - - - - - - - - - - - - - - - - - - - - 05 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06 - - - - - - - - - - - - - - - - - - - - - - - - - - - - 08 - - - - - - - - - - - - - - - - 10 - - - - - - - - - - - - - - - - - - - - - - - - - - - 13 - - - - - - - - - - - - - - - - - - - - - - - - 15 - - - - - - - - - - - - - - - - - - - - - - - - 16 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17 - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18 I. Safety Instructions 05 The laser engraver uses a high-density laser beam to irradiate materials during engraving or cutting, generating high temperatures on the material surface to vaporize it without burning. However, most materials are inherently flammable and may catch fire, producing an open flame that can damage the machine and its surrounding environment. Please follow the guidelines below when using the laser engraver: 1. Do not place this product near flammable or explosive materials, volatile solvents, or high heat sources. Always operate the machine in a well-ventilated, cool, and low-dust environment. 2. Do not replace the power cable with other cables. Use only the power cable provided with this product. 3. Caution—use of controls or adjustments or performance of procedures …

Text truncated - open the document above for the full version.

ShenzhenSculpfunTechnologyCo., Ltd. Address:Room 401, Building13, No. 140, GuanlanAvenue,Sihe Community,Fucheng Street, LonghuaDistrict,ShenzhenCity, GuangdongChina Tel: +86-13049380508;Fax: +86-0755-89366592 Email:[email protected] AttestationLetter Date: 2026-07-17 FEDERALCOMMUNICATIONSCOMMISSIONS Authorizationand EvaluationDivision 7435 OaklandMills Road Columbia,MD 21046 To whom it may concern: Our productLaser EngravingMachine,Model number:E1 Pro Dual , E1, E1 Dual, E1 Pro, FCC ID: 2BF27E1,for marketingpurpose,this productonly supports2.4G WiFi (2412-2462MHzb/g/n20/n40modes ).The other functions,bands and modes were disabled to use by manufacturein the software,the end user has no capabilityto activateit. SincerelyYours, Signature: JIA HE ProductManager 肛A HE-

ShenzhenSculpfunTechnologyCo., Ltd. Address:Room 401, Building13, No. 140, GuanlanAvenue,Sihe Community,FuchengStreet, Longhua District,ShenzhenCity, GuangdongChina Tel: +86 -13049380508; Fax: +86- 0755-89366592 Email:[email protected] CFR 47 §2.911(d)(5)(i)AttestationLetter AttestationLetter Date: 2026-07-17 FEDERALCOMMUNICATIONSCOMMISSIONS Authorizationand EvaluationDivision 7435 OaklandMills Road Columbia,MD 21046 Ref: AttestationStatementsCFR 47 §2.911(d)(5)(i)Filing FCC ID: 2BF27E1 ShenzhenSculpfunTechnologyCo., Ltd. certifiesthat the equipmentfor which authorizationis soughtis not“covered”equipmentprohibitedfrom receivingan equipmentauthorization pursuantto section2.903 of the FCC rules. Sincerely, Signature ContactPerson:JIA HE Title: ProductManager 肛A HE-

ShenzhenSculpfunTechnologyCo., Ltd. Address:Room 401, Building13, No. 140, GuanlanAvenue,Sihe Community,FuchengStreet, Longhua District,ShenzhenCity, GuangdongChina Tel: +86 -13049380508; Fax: +86-0 755-89366592 Email:[email protected] CFR 47 §2.911 (d)(5)(ii)AttestationLetter AttestationLetter Date: 2026-07-17 FEDERALCOMMUNICATIONSCOMMISSIONS Authorizationand EvaluationDivision 7435 OaklandMills Road Columbia,MD 21046 Ref: AttestationStatementsCFR 47 §2.911(d)(5)(ii)Filing FCC ID: 2BF27E1 ShenzhenSculpfunTechnologyCo., Ltd. certifiesthat as of the date of the filing of the application,the applicantis not identifiedon the CoveredList as an entity producing“covered” equipment. We also certify that, as of the date of the filing of the application,the equipmentdoes not utilize cyber-securityor anti-virussoftwarefrom KasperskyLab, Inc, or any of its successorsand assignees,which is also on the “coveredlist ”. Sincerely, Signature: JIA HE ProductManager 肛A HE-

U.S. AGENT LETTER OF ATTESTATION Date: 2026-07-17 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2BF27E1 Shenzhen Sculpfun Technology Co., Ltd. certifies that, as of the date of the filing of the application, Iconsigh Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. Shenzhen Sculpfun Technology Co., Ltd. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Iconsigh Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: Iconsigh Inc. Address: 2310 Homestead Road, Suite C1, Los Altos, CA 94024, USA FRN: 0033398652 Tel.: +1 (408) 320-9867 Email: [email protected] Signed by (printed name): Benjamin Kaur Signature: Applicant: Shenzhen Sculpfun Technology Co., Ltd. Address: Room 401, Building 13, No. 140, Guanlan Avenue, Sihe Community, Fucheng Street, Longhua District, Shenzhen City, Guangdong China FRN: 0035331347 Tel: 86-13049380508 Fax: 86-0755-8936 6592 Email: [email protected] Signed by (printed name): JIA HE Signature:

ShenzhenSculpfunTechnologyCo., Ltd. Address: Room 401, Building13, No. 140, GuanlanAvenue,Sihe Community,FuchengStreet, Longhua District,ShenzhenCity, GuangdongChina Tel: +86 -13049380508; Fax: +86- 0755-89366592 Email:[email protected] FCC Authorization Date: 2026-07-17 FEDERALCOMMUNICATIONSCOMMISSIONS Authorizationand EvaluationDivision 7435 OaklandMills Road Columbia,MD 21046 Subject:Agent Authorization To whom it may concern: We , ShenzhenSculpfunTechnologyCo., Ltd., the undersigned,herebyauthorizesBay Area ComplianceLaboratoriesCorp. (Shenzhen)to act on its behalf in all matters relatingto applicationfor Equipmentauthorization,includingthe signingof all documentsrelatingto these matters.All acts carriedout by Bay Area Compliance LaboratoriesCorp. (Shenzhen)on our behalf shall have the same effect as our own action. We, the undersigned,herebycertify that we are not subjectto a denial of federalbenefits, that includesFCC benefits,pursuantto Section5301 of the Anti-DrugAbuse Act of 1988, 21 U.S.C.862. This authorizationis valid until furtherwrittennotice from the applicant. SincerelyYours, Signature: JIA HE ProductManager QA-FR-170-B7/29/2014 肛A HE-

ShenzhenSculpfunTechnologyCo., Ltd. Address: Room 401, Building13, No. 140, GuanlanAvenue,Sihe Community,FuchengStreet, LonghuaDistrict,ShenzhenCity, GuangdongChina Tel: +86 -13049380508; Fax: +86- 0755-89366592 Email:[email protected] FCCConfidentialAuthorization Date: 2026-07-17 FEDERALCOMMUNICATIONSCOMMISSIONS Authorizationand EvaluationDivision 7435 OaklandMills Road Columbia,MD 21046 Subject:ConfidentialityRequestregardingapplicationfor certificationof FCC ID: 2BF27E1 In accordancewith Sections0.457 and 0.459 of the Commission’s Rules, ShenzhenSculpfunTechnologyCo.,Ltd.herebyrequestslong-termconfidential treatmentof informationaccompanyingthis applicationas outlinedbelow: Block Diagram Schematics OperationDescription The above materialscontainproprietaryand confidentialinformationnot customarily releasedto the public.The public disclosureof these materialsprovidesunjustified benefitsto its competitorsin the market. SincerelyYours, Signature JIA HE ProductManager 肛A HE-

Shenzhen Sculpfun Technology Co., Ltd. Address: Room 401, Building 13, No. 140, Guanlan Avenue, Sihe Community, Fucheng Street, Longhua District, Shenzhen City, Guangdong China Tel: +86-13049380508; Fax: +86-0755-8936 6592 Email: [email protected] Declaration Of Similarity Date: 2026-07-17 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern: We, Shenzhen Sculpfun Technology Co., Ltd., hereby declare that product: Laser Engraving Machine, Model number: E1 Pro Dual, E1, E1 Dual, E1 Pro, FCC ID: 2BF27E1 are electrically identical with the same circuit design, PCB layout, internal wiring, product functions, the difference between them is as below. Model Laser E1 12W 455nm laser E1 Pro 21W 455nm laser E1 Dual 12W455nm laser+3W1064nm laser E1 Pro Dual 21W455nm laser+3W1064nm laser Please contact me should there be need for any additional clarification or information. Best Regards, Signature JIA HE Product Manager

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-EXP Page 1 of 9 EUT EXTERNAL PHOTOGRAPHS Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-EXP Page 2 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-EXP Page 3 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-EXP Page 4 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-EXP Page 5 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-EXP Page 6 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-EXP Page 7 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-EXP Page 8 of 9 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-EXP Page 9 of 9

Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: 2601S16709E-RF FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 1 of 16 EUT INTERNAL PHOTOGRAPHS Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 2 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 3 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 4 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 5 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 6 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 7 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 8 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 9 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 10 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 11 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 12 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 13 of 16 ANT Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 14 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 15 of 16 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-INP Page 16 of 16

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-00A TR-EM-RF004 Page 26 of 130 Version 4.1 RF EXPOSURE EVALUATION MPE-Based Exemption Applicable Standard According to subpart 15.247 (i) and subpart 2.1091 systems operating under the provisions of this section shall be operated in a manner that ensures the public is not exposed to RF energy level in excess of the communication guidelines. According to KDB 447498 D04 v01 Interim General RF Exposure Guidance MPE-Based Exemption: General frequency and separation-distance dependent MPE-based effective radiated power(ERP) thresholds are in Table B.1 [Table 1 of § 1.1307(b)(3)(i)(C)] to support an exemptionfrom further evaluation from 300 kHz through 100 GHz. Ris the minimum separation distance in meters f = frequency in MHz For multiple RF sources: Multiple RF sources are exempt if: in the case of fixed RF sources operating in the same time-averaging period, or of multiple mobile or portable RF sources within a device operating in the same time averaging period, if the sum of the fractional contributions to the applicable thresholds is less than or equal to 1 as indicated in the following equation: Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-00A TR-EM-RF004 Page 27 of 130 Version 4.1 Result Antenna Gain#ERP Mode Frequency (MHz) Tune up conducted power # (dBm) (dBi)(dBd)(dBm)(W) Evaluation Distance (m) ERP Limit (W) 2.4GWiFi2412-246219 2-0.1518.850.0770.20.768 Note: The tune up conducted power and antenna gain was declared by the applicant. To maintain compliance with the FCC’s RF exposure guidelines, place the equipment at least 20cm from nearby persons. Result: Compliant

Note: The information marked # is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP or any agency of the U.S. Government. This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “▼”. Bay Area Compliance Laboratories Corp. (Shenzhen) 5F(B-West) , 6F, 7F, the 3rd Phase of Wan Li Industrial Building D, Shihua Rd, FuTian Free Trade Zone, Shenzhen, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn TR-EM-RF004 Page 1 of 130 Version 4.1 TEST REPORT Applicant Name:Shenzhen Sculpfun Technology Co., Ltd. Address:Room 401, Building 13, No. 140, Guanlan Avenue, Sihe Community, Fucheng Street, Longhua District, Shenzhen City, Guangdong China Report Number:2601S16709E-RF-00A FCC ID:2BF27E1 Test Standard (s) FCC PART 15.247 Sample Description Product Type:Laser Engraving Machine Model No.:E1 Pro Dual Multiple Model(s) No.:E1, E1 Dual, E1 Pro Trade Mark:SCULPFUN Date Received:2026-05-07 Issue Date:2026-08-04 Test Result:Pass ▲ ▲ In the configuration tested, the EUT complied with the standards above. Prepared and Checked By:Approved By: Cheeb HuangNancy Wang RF EngineerRF Supervisor Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-00A TR-EM-RF004 Page 2 of 130 Version 4.1 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ..........................................................................................................................3 GENERAL INFORMATION ........................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)......................................................................................4 OBJECTIVE ....................................................................................................................................................................4 TEST METHODOLOGY....................................................................................................................................................4 MEASUREMENT UNCERTAINTY .....................................................................................................................................5 TEST FACILITY ..............................................................................................................................................................5 SYSTEM TEST CONFIGURATION ...........................................................................................................................6 SUMMARY OF TEST RESULTS ................................................................................................................................9 TEST EQUIPMENT LIST ..........................................................................................................................................10 REQUIREMENTS AND TEST PROCEDURES ......................................................................................................12 AC LINE CONDUCTED EMISSIONS...............................................................................................................................12 SPURIOUS EMISSIONS ..................................................................................................................................................14 6 DB EMISSION BANDWIDTH & 99% OCCUPIED BANDWIDTH ....................................................................................17 MAXIMUM CONDUCTED OUTPUT POWER ...................................................................................................................19 100 KHZ BANDWIDTH OF FREQUENCY BAND EDGE....................................................................................................20 CONDUCTED SPURIOUS EMISSION...............................................................................................................................21 POWER SPECTRAL DENSITY ........................................................................................................................................22 DUTY CYCLE ...............................................................................................................................................................25 RF EXPOSURE EVALUATION ................................................................................................................................26 ANTENNA REQUIREMENT .....................................................................................................................................28 TEST DATA AND RESULTS .....................................................................................................................................29 AC LINE CONDUCTED EMISSIONS...............................................................................................................................29 SPURIOUS EMISSIONS ..................................................................................................................................................36 6DB EMISSION BANDWIDTH......................................................................................................................................107 99% OCCUPIED BANDWIDTH ..................................................................................................................................…

Text truncated - open the document above for the full version.

Mem ConfirmedbyZhangDate HUMIDITY50±20%rh Band2.4GColor VersionV1.0 IssuedbyJasonCheckedby 普尔信通讯科技(深圳)有限公司 PercssonCommunicationEquipmentCo.,Ltd AntennaTestReport 一．TESTINSTRUMENTATION ThistestreportbelongstoPERCSSONCOMMUNICATIONEQUIPMENTCO.LTD.andrelatedclientsto file,pleasekeepingitpropely,withoutourcompanyandrelatedclientsallowed,anybodyhasno rightstorevalittopublic. CHAMBERSATIMOChamber WirelessNetworkingTestSetAgilent89605515C NETWORKANALYZERAgilent8753D TEMPERATURE 20±2 °C 2dBi Gain(Peak) black Add: Espressif Systems (Shanghai) Co., Ltd.Suite 204, Block 2, 690 Bibo Road, Zhangjiang Hi-Tech Park, Pudong New Area, Shanghai, ChinaPostal Code: 201203 普尔信通讯科技(深圳)有限公司 PercssonCommunicationEquipmentCo.,Ltd AntennaDimension ThistestreportbelongstoPERCSSONCOMMUNICATIONEQUIPMENTCO.LTD.andrelatedclientsto file,pleasekeepingitpropely,withoutourcompanyandrelatedclientsallowed,anybodyhasno rightstorevalittopublic. 普尔信通讯科技(深圳)有限公司 PercssonCommunicationEquipmentCo.,Ltd ThistestreportbelongstoPERCSSONCOMMUNICATIONEQUIPMENTCO.LTD.andrelatedclientsto file,pleasekeepingitpropely,withoutourcompanyandrelatedclientsallowed,anybodyhasno rightstorevalittopublic. 普尔信通讯科技(深圳)有限公司 PercssonCommunicationEquipmentCo.,Ltd ThistestreportbelongstoPERCSSONCOMMUNICATIONEQUIPMENTCO.LTD.andrelatedclientsto file,pleasekeepingitpropely,withoutourcompanyandrelatedclientsallowed,anybodyhasno rightstorevalittopublic. 普尔信通讯科技(深圳)有限公司 PercssonCommunicationEquipmentCo.,Ltd 二.Definitions VSWR ： VoltageStandingWaveRate TRP ： totalradiatedpower TIS ： totalistropicsensitivity ThistestreportbelongstoPERCSSONCOMMUNICATIONEQUIPMENTCO.LTD.andrelatedclientsto file,pleasekeepingitpropely,withoutourcompanyandrelatedclientsallowed,anybodyhasno rightstorevalittopublic. WIFI VSWR1.1 普尔信通讯科技(深圳)有限公司 PercssonCommunicationEquipmentCo.,Ltd ThistestreportbelongstoPERCSSONCOMMUNICATIONEQUIPMENTCO.LTD.andrelatedclientsto file,pleasekeepingitpropely,withoutourcompanyandrelatedclientsallowed,anybodyhasno rightstorevalittopublic.

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-00A-TSP Page 1 of 3 TEST SETUP PHOTOGRAPHS Conducted Emissions - Front View Conducted Emissions - Side View Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-00A-TSP Page 2 of 3 Radiated Emissions View (Below 30MHz) Radiated Emissions View (Below 1 GHz) Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601S16709E-RF-00A-TSP Page 3 of 3 Radiated Emissions View (1-18 GHz) Radiated Emissions View (18-25 GHz)