2BFJA-N700Neideso Dash Cam

User Manual Neideso Dash Cam N700 Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.NOTE:This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Statement:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.The equipment complies with FCC Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

* the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. Shenzhen Weiwo Innovation Technology Co., Ltd. U.S. Agent Designation for Service of Process -Certification Attestation Letter DATE: 2024-3-22 TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTN.: Reviewing Engineer FCC ID: 2BFJA-N700 FRN of applicant: 0035157221 Per section 2.911(d)(7) of the FCC rules, Shenzhen Weiwo Innovation Technology Co., Ltd. (“the applicant”) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company name: Linkage Technology, LLC Address: 10601 NEWCOMBE ST BROOMFIELD CO 80021-3630 USA FRN Number: 0033401480 Contact Name: Candy Jones/ sales manager Telephone No: +01-509-768-2249 Email: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Signed: Printed name: Yu Ming Ou Title: manager Company Name: Shenzhen Weiwo Innovation Technology Co., Ltd. Date: 2024-3-22 Signed: Printed name: Candy Jones Title: sales manager Company Name: Linkage Technology, LLC Date: 2024-3-22 Agent Signed (if different from Applicant):

Shenzhen Weiwo Innovation Technology Co., Ltd. Covered Equipment Certification Attestation Letter DATE: 2024-3-22 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2BFJA-N700 Shenzhen Weiwo Innovation Technology Co., Ltd. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List , the applicant should include an explanation on why the equipment is not “covered” equipment. Shenzhen Weiwo Innovation Technology Co., Ltd. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Signed: Name:Yu Ming Ou Title:manager Company: Shenzhen Weiwo Innovation Technology Co., Ltd. Date: 2024-3-22

DATE: 2024/03/22 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen POCE Technology Co., Ltd. Address:101-102 Building H5 & 1/F., Building H, Hongfa Science & Technology Park, Tangtou, Shiyan, Bao'an District, Shenzhen, Guangdong, China to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Shenzhen Weiwo Innovation Technology Co., Ltd. Address: Room 504, Building 4, Manjinghua Yiluan Building, N0.230 Xixiang Avenue, Longteng Community, Xixiang Street, Bao'an District, Shenzhen, P.R.China (Applicant Name and address) <Signature> Name:Yu Ming Ou Title:manager Company: Shenzhen Weiwo Innovation Technology Co., Ltd.

DATE：2024-3-22 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BFJA-N700 Product Name:Neideso Dash Cam R equest for Confidentiality Pursuant t o Sections 0.457 an d 0.459 of the commissions rules, we hereby request that th e following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...) Schematics Block diagram Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name:Yu Ming Ou Title:manager Company: Shenzhen Weiwo Innovation Technology Co., Ltd.

Date：2024-3-22 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party t o the application authorized hereunder i s subject t o the denial of benefits, including FCC benefits, pursuant t o Section 5301 of the Anti-Drug Abuse Act o f 1988, 21 U.S.C.853(a). Sincerely, <Signature> Name:Yu Ming Ou Title:manager Company: Shenzhen Weiwo Innovation Technology Co., Ltd.

FCC ID:2BFJA-N700 Shenzhen Weiwo Innovation Technology Co., Ltd. Model Confirmation Letter We Shenzhen Weiwo Innovation Technology Co., Ltd. , certify the product: Neideso Dash Cam， Model No.:N700, N100, N300, N500, N600, N900, The product has many models, the appearance of the product is consistent, and the BOM and PCB are also consistent. Different versions of built-in software result in different product names, but it does not affect the emc and rf performance of the product. Test sample model:N700 Date: 2023-10-27 <Signature> Name:Yu Ming Ou Title:manager Company: Shenzhen Weiwo Innovation Technology Co., Ltd.

FCC ID: 2BFJA-N700 External

Label Size: 25*15mm Neideso Dash Cam MODEL: N700 Input Voltage: 5V 2.0A FCC ID: 2BFJA-N700

FCC ID: 2BFJA-N700 Internal

Page 1 of 1 RF Exposure Evaluation Report 1 RF EXPOSURE Product Name: Neideso Dash Cam Model No.: N700, N100, N300, N500, N600, N900 FCC ID: 2BFJA-N700 2. RF Exposure Evaluation FCC KDB447498 D01 General RF Exposure Guidance v06: Mobile and Portable Device, RF Exposure, Equipment Authorization Procedures. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1091: Radiofrequency radiation exposure evaluation: mobile devices. 2.1 LIMITS According to FCC Part1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in part1.1307(b) F= Frequency in MHz Friis Formula Friis transmission formula: Pd = (Pout*G)/(4* Pi * R 2) Where Page 1 of 1 Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd id the limit of MPE . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. 2.2 EUT RF EXPOSURE EVALUATION 5G-WIFI ANT1:2.27dBi The Max Conducted Peak Output Power or Total Power refer to report No.: POCE240229001RF001 5.8GWIFI worst mode and channel: Test channel Total Power(dBm) Maximum tune-up Power (dbm) Maximum tune-up Power (dbm) 802.11a-5745MHz 7.86 8±1 9 802.11n(HT20) - 5745MHz 7.91 8±1 9 Test worst case Maximum tune-up Power (dbm) Maximum tune-up Power (mW) Calculated value (mW/cm2) Limit (mW/cm2) 9 7.943 0.0027 1.0 Remark: Pd = (Pout*G)/(4* Pi * R 2 )=( 7.943*1.686)/(4*3.1415*20*20)= 0.0027, G=10 gain/10 =1.686 EUT wifi-5G module is more than 20cm away from the human body. Calculated value is less than the limit value of 1.0, so there is no sar requirement.

V1.0 Report No.: POCE240229001RF001 101-102 Building H5 & 1/F., Building H,Hongfa Science & Technology Park, Tangtou, Shiyan, Bao’an District, Shenzhen, Guangdong, China Web:http://www. poce-cert.com Tel: 86-755-29113252 E-mail: [email protected] Page 1 of 83 RF TEST REPORT For Shenzhen Weiwo Innovation Technology Co., Ltd. Product Name: Neideso Dash Cam Test Model(s).: N700 Report Reference No. : POCE240229001RF001 FCC ID : 2BFJA-N700 Applicant’s Name : Shenzhen Weiwo Innovation Technology Co., Ltd. Address : Room 504, Building 4, Manjinghua Yiluan Building, N0.230 Xixiang Avenue, Longteng Community, Xixiang Street, Bao'an District, Shenzhen, P.R.China Testing Laboratory : Shenzhen POCE Technology Co., Ltd. Address : 101-102 Building H5 & 1/F., Building H, Hongfa Science & Technology Park, Tangtou, Shiyan, Bao'an District, Shenzhen, Guangdong, China Test Specification Standard : 47 CFR Part 15E KDB 789033 D02 General U-NII Test Procedures New Rules v02r01 Date of Receipt : February 29, 2024 Date of Test : February 29, 2024 to March 13, 2024 Data of Issue : March 13, 2024 Result : Pass Note: This report shall not be reproduced except in full, without the written approval of Shenzhen POCE Technology Co., Ltd. This document may be altered or revised by Shenzhen POCE Testing Technology Co., Ltd. personnel only, and shall be noted in the revision section of the document. The test results in the report only apply to the tested sample. V1.0 Report No.: POCE240229001RF001 101-102 Building H5 & 1/F., Building H,Hongfa Science & Technology Park, Tangtou, Shiyan, Bao’an District, Shenzhen, Guangdong, China Web:http://www. poce-cert.com Tel: 86-755-29113252 E-mail: [email protected] Page 2 of 83 Revision History Of Report Version Description REPORT No. Issue Date V1.0 Original POCE240229001RF001 March 13, 2024 NOTE1: The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Compiled by: Supervised by: Approved by: Keren Huang / Test Engineer Stone Yin / Project Engineer Tom Chen / Manager V1.0 Report No.: POCE240229001RF001 101-102 Building H5 & 1/F., Building H,Hongfa Science & Technology Park, Tangtou, Shiyan, Bao’an District, Shenzhen, Guangdong, China Web:http://www. poce-cert.com Tel: 86-755-29113252 E-mail: [email protected] Page 3 of 83 CONTENTS 1 TEST SUMMARY ........................................................................................................................................... 5 1.1 TEST STANDARDS .................................................................................................................................. 5 1.2 SUMMARY OF TEST RESULT .................................................................................................................... 5 2 GENERAL INFORMATION ............................................................................................................................ 6 2.1 CLIENT INFORMATION ............................................................................................................................. 6 2.2 DESCRIPTION OF DEVICE (EUT) .............................................................................................................. 6 2.3 DESCRIPTION OF TEST MODES ................................................................................................................ 6 2.4 DESCRIPTION OF SUPPORT UNITS ........................................................................................................... 7 2.5 EQUIPMENTS USED DURING THE TEST .................................................................................................... 8 2.6 STATEMENT OF THE MEASUREMENT UNCERTAINTY ................................................................................. 9 2.7 AUTHORIZATIONS ................................................................................................................................... 9 2.8 ANNOUNCEMENT .................................................................................................................................... 9 3 RADIO SPECTRUM MATTER TEST RESULTS (RF) ................................................................................. 10 3.1 DUTY CYCLE ........................................................................................................................................ 10 3.1.1 E.U.T. Operation: .................................................................................................................... 10 3.1.2 Test Setup Diagram: ............................................................................................................... 10 3.1.3 Test Data: ............................................................................................................................... 10 3.2 MAXIMUM CONDUCTED OUTPUT POWER .................................................................................................. 11 3.2.1 E.U.T. Operation: ..................................................................................................................... 11 3.2.2 Test Setup Diagram: ................................................................................................................ 11 3.2.3 Test Data: ................................................................................................................................ 11 3.3 POWER SPECTRAL DENSITY .................................................................................................................. 12 3.3.1 E.U.T. Operation: .................................................................................................................... 12 3.3.2 Test Setup Diagram: ..................................................................................…

Text truncated - open the document above for the full version.

Antenna Test Report PROJECT：N700 Applicant：WEIYIKE ELECTRONIC CO., LTD. FRE.： WIFI(2.4G+5G) VER.：A DATE：2024-1-3 专业的4G/3G/GPS/WIFI等天线方案设计及供应商 1. Antenna Matching Network 2.S11 Parameter-VSWR 3. 1 Gain & Efficiency 3. 2 3D Pattern 4. OTA Data 5. Antenna Assembly & environmental processing 6. conclusion 1 Content 2 Co ntent Antenna Photo & Length (mm) 1.Test system Series N/A Antenna PA Shunt 01 N/A Shunt 02 N/A LocationDescriptionVendor Shunt 01N/AN/A SeriesN/AN/A Shunt 02N/AN/A 2. Antenna Matching Network S11 Parameter-SWR Gain & Efficiency Gain & Efficiency

FCC ID: 2BFJA-N700 Undesirable emission limits (below 1GHz) Undesirable emission limits (above 1GHz)