2BFL9-Q018Full coverage adhesive massager

Full coverage adhesive massager *Product before use 1. Charging (please charge Product before use) 2. Cleaning (clean with water or a neutral detergent such as bath lotion) How to charge 1. Please use the supporting USB charging cable with a power adapter or computer to link *Please use the national standard 5V (1A or 2A or 4.5A) power adapter for charging *Cannot charge when the computer is in hibernation *Gently align the end of the charging USB cable with the charging port and insert it A. Light breathing flashing: charging B. Keep the light on: full C: The invisible charging port is shown below D: After charging, please pull out the end of the charging USB cable gently. Charging precautions *Please make sure the charger is dry and clean before charging *Do not expose to high temperature or humidity while charging *If stored for a long time, please charge it once a month to maintain its charging performance *There is a rechargeable lithium battery in Product, and the scrap should be treated as scrapped old electronic products and recycled to the corresponding recycling station Remote control mode Remote control button description 1:Product remote control on/off button 1. Long press for 2 seconds to turn on or turn off the remote control. When it is turned on, the remote control is always on white 2: Clitoris vibration button 1. In the power-on state, click the clitoral vibration button, the white light flashes, and the clitoral vibration function 2. Click to cycle through 9 vibration frequencies 3. Long press the clitoral vibration button to turn off this function alone (does not affect other functions) 3: When the host is in standby mode, briefly press the vibration button to start the frequency modulation of the small motor, cycle for 10 frequencies, and press and hold for 1.2 seconds to shut down. 4. There are a total of 10 vibration modes. Small motor button Big motor button This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure statement The device has been evaluatec to meel general RF exposure requirement. The device can be used in porlable exposure condition without restriction.

Dongguan Xing Klai Intelligent Tecchnology Company Limited 1/1 Letter of Authorization Company: Dongguan Xing Klai Intelligent Tecchnology Company Limited Address: NO.3. DALONG RING ROAD SOUTH BANK, YOUGANPU VILLAGE, FENGGANG TOWN, DONGGUAN CITY. Product Name: Full coverage adhesive massager Model Number: Q018 Q029, Q033, Q035, Q050, Q086, Q087, Q088, Q089, B010, B021, APS003, CRS004, APS002, JES001, JES002, JES003, ADS002, ADS003, ADS004 FCC Identifier: 2BFL9-Q018 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Jack bu Date: 2024-03-28 Title: Manager Signature of applicant:

Shenzhen Axiwo Technology Co., Ltd. 1/1 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2024-03-28 Subject: Request for Confidentiality FCC ID: 2BFL9-Q018 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual No ☐ Internal Photos No ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Name: Jack bu Date: 2024-03-28 Title: Manager Signature of applicant:

Dongguan Xing Klai Intelligent Tecchnology Company Limited Product Similarity Declaration Company: Dongguan Xing Klai Intelligent Tecchnology Company Limited Address: NO.3. DALONG RING ROAD SOUTH BANK, YOUGANPU VILLAGE, FENGGANG TOWN, DONGGUAN CITY. Product Name: Full coverage adhesive massager Model Number: Q018 Q029, Q033, Q035, Q050, Q086, Q087, Q088, Q089, B010, B021, APS003, CRS004, APS002, JES001, JES002, JES003, ADS002, ADS003, ADS004 FCC Identifier: 2BFL9-Q018 We (Dongguan Xing Klai Intelligent Tecchnology Company Limited) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.,), same mechanical structure and design (including product enclosure, materials, etc.,), the only difference is the model name and appearance color. Client’s signature Name: Jack bu Date: 2024-03-28 Title: Manager Signature of applicant:

Dongguan Xing Klai Intelligent Tecchnology Company Limited 1/1 Letter of Authorization Company: Dongguan Xing Klai Intelligent Tecchnology Company Limited Address: NO.3. DALONG RING ROAD SOUTH BANK, YOUGANPU VILLAGE, FENGGANG TOWN, DONGGUAN CITY. Product Name: Full coverage adhesive massager Model Number: Q018 Q029, Q033, Q035, Q050, Q086, Q087, Q088, Q089, B010, B021, APS003, CRS004, APS002, JES001, JES002, JES003, ADS002, ADS003, ADS004 FCC Identifier: 2BFL9-Q018 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Jack bu Date: 2024-03-28 Title: Manager Signature of applicant:

Shenzhen Axiwo Technology Co., Ltd. 1/1 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2024-03-28 Subject: Request for Confidentiality FCC ID: 2BFL9-Q018 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual No ☐ Internal Photos No ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Name: Jack bu Date: 2024-03-28 Title: Manager Signature of applicant:

Shenzhen DL Testing Technology Co., Ltd. EUT PHOTO(External Photos) Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. ※※※※※ END OF REPORT ※※※※※

Size: 18*14mm M/N: Q018 FCC ID: 2BFL9-Q018 Label location

Shenzhen DL Testing Technology Co., Ltd. EUT PHOTO(Internal Photos) Shenzhen DL Testing Technology Co., Ltd. ANT Shenzhen DL Testing Technology Co., Ltd. ※※※※※ END OF REPORT ※※※※※

FCC ID: 2BFL9-Q018 RF Exposure Evaluation According to KDB 447498 D01 V06 and part 2.1093，Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f (GHz) ] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where f (GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison EIRP=E Meas +20log(d Meas )-104.7 EIRP is the equivalent isotropically radiated power, in dBm E Meas is the field strength of the emission at the measurement distance, in dBμV/m d Meas is the measurement distance, in m Here, Field strength (dBuV/m) EIRP (dBm) Max tune-up (mW) Frequency (MHz) Min. distance(mm) Calc. thresholds limit 48.86 -46.3 0.000023 433.92 5 0.0000031 3.0 So a SAR test is not required

433mHZ Antenna report Manufacturer: Dongguan Xing Klai Intelligent Tecchnology Company Limited M/N:433MHZ 1.Gain and Effciency Freq(MHZ) Efficiency(%) Gain(dBi) 430 30.5 0.25 431 31.4 0.36 432 32.5 0.48 433 33.6 0.56 434 34.5 0.16 435 31.6 0.19 436 32.5 0.21 437 30.5 0.15 438 29.5 0.14

Shenzhen DL Testing Technology Co., Ltd. Report No.: DL-20240314061E Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 1 of 25 FCC Part 15C Test Report FCC ID: 2BFL9-Q018 Applicant: Dongguan Xing Klai Intelligent Tecchnology Company Limited Address: NO.3. DALONG RING ROAD SOUTH BANK, YOUGANPU VILLAGE, FENGGANG TOWN, DONGGUAN CITY. Manufacturer: Dongguan Xing Klai Intelligent Tecchnology Company Limited Address: NO.3. DALONG RING ROAD SOUTH BANK, YOUGANPU VILLAGE, FENGGANG TOWN, DONGGUAN CITY. EUT: Full coverage adhesive massager Trade Mark: N/A Model Number: Q018 Q029, Q033, Q035, Q050, Q086, Q087, Q088, Q089, B010, B021, APS003, CRS004, APS002, JES001, JES002, JES003, ADS002, ADS003, ADS004 Date of Receipt: Mar. 14, 2024 Test Date: Mar. 14, 2024 - Mar. 26, 2024 Date of Report: Mar. 26, 2024 Prepared By: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Building C, Shuanghuan, No.8, Baoqing Road, Baolong Industrial Zone, Baolong Street, Longgang District, Shenzhen, Guangdong, China Applicable Standards: FCC PART 15 C 15.231 ANSI C63.10:2013 Test Result: Pass Report Number: DL-20240314061E Prepared (Test Engineer): Alisa Song Reviewer (Supervisor): Jack Bu Approved (Manager): Jade Yang This test report is based on a single evaluation of one sample of above mentioned products. It is not permitted to be duplicated in extracts without written approval of Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Report No.: DL-20240314061E Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 2 of 25 Table of Contents Page 1 . SUMMARY OF TEST RESULTS 4 1.1 MEASUREMENT UNCERTAINTY 4 2 . GENERAL INFORMATION 5 2.1 GENERAL DESCRIPTION OF EUT 5 2.2 DESCRIPTION OF TEST MODES 5 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 6 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 6 2.5 TABLE OF PARAMETERS OF TEST SOFTWARE SETTING 6 2.6 EQUIPMENTS LIST FOR ALL TEST ITEMS 7 3 . EMC EMISSION TEST 8 3.1 CONDUCTED EMISSION MEASUREMENT 8 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS 8 3.1.2 TEST PROCEDURE 8 3.1.3 DEVIATION FROM TEST STANDARD 8 3.1.4 TEST SETUP 9 3.1.5 EUT OPERATING CONDITIONS 9 3.1.6 TEST RESULTS 9 3.2 RADIATED EMISSION MEASUREMENT 10 3.2.1 RADIATED EMISSION LIMITS 10 3.2.2 TEST PROCEDURE 11 3.2.3 DEVIATION FROM TEST STANDARD 11 3.2.4 TEST SETUP 12 3.2.5 EUT OPERATING CONDITIONS 13 3.2.6 TEST RESULTS (BETWEEN 9KHZ – 30 MHZ) 14 3.2.7 TEST RESULTS (BETWEEN 30MHZ – 1GHZ) 15 3.2.8 TEST RESULTS (1GHZ~25GHZ) 18 4 . BANDWIDTH TEST 19 4.1 APPLIED PROCEDURES / LIMIT 19 4.1.1 TEST PROCEDURE 19 4.1.2 DEVIATION FROM STANDARD 19 4.1.3 TEST SETUP 19 4.1.4 EUT OPERATION CONDITIONS 19 4.1.5 TEST RESULTS 20 5 . CALCULATION OF AVERAGE FACTOR 21 5.1 APPLIED PROCEDURES / LIMIT 21 5.1.1 TEST PROCEDURE 21 5.1.2 TEST SETUP 21 5.1.3 EUT OPERATION CONDITIONS 21 Shenzhen DL Testing Technology Co., Ltd. Report No.: DL-20240314061E Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 3 of 25 Table of Contents Page 5.1.4 TEST RESULTS 22 6 . TRANSMISSION CEASE TIME 23 6.1 APPLIED PROCEDURES / LIMIT 23 6.1.1 TEST PROCEDURE 23 6.1.2 DEVIATION FROM STANDARD 23 6.1.3 TEST SETUP 23 6.1.4 EUT OPERATION CONDITIONS 23 6.1.5 TEST RESULTS 24 7 . ANTENNA REQUIREMENT 25 7.1 STANDARD REQUIREMENT 25 7.2 EUT ANTENNA 25 8 . TEST SEUUP PHOTO 25 9 . EUT PHOTO 25 Shenzhen DL Testing Technology Co., Ltd. Report No.: DL-20240314061E Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 4 of 25 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.231) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission N/A 15.209,15.231b Fundamental &Radiated Spurious Emission Measurement PASS 15.231a Transmission cease time PASS 15.215 20dB Bandwidth PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Test lab: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Building C, Shuanghuan, No.8, Baoqing Road, Baolong Industrial Zone, Baolong Street, Longgang District, Shenzhen, Guangdong, China FCC Test Firm Registration Number: 854456 Designation Number: CN1307 IC Registered No.: 27485 CAB ID.: CN0118 1.1 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2,providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 Conducted Emission Test ±2.56dB 2 RF power,conducted ±0.42dB 3 Spurious emissions,conducted ±2.76dB 4 All emissions,radiated(<1G) ±3.65dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% Shenzhen DL Testing Technology Co., Ltd. Report No.: DL-20240314061E Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 5 of 25 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Product Name: Full coverage adhesive massager Trademark N/A Model No.: Q018 Q029, Q033, Q035, Q050, Q086, Q087, Q088, Q089, B010, B021, APS003, CRS004, APS002, JES001, JES002, JES003, ADS002, ADS003, ADS004 Model Difference The product's different for model number and appearance color. Operation Frequency: 433.92MHz Channel numbers: 1 Channels Modulation technology: FSK Antenna Type: Internal Antenna Antenna gain: 0.56dBi Power supply: DC 3V from battery Note: 1.For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. 2.The EUT’s all information provided by client. 2.2 DESCRIPTION OF TEST MODES Note: (1) New battery is used during the test To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mention…

Text truncated - open the document above for the full version.

Shenzhen DL Testing Technology Co., Ltd. EUT TEST PHOTO Radiated Measurement Photos ※※※※※ END OF REPORT ※※※※※