2BFMW-20240220Bar Display

Agent letter FCC attestation statement Kiwa Page 1 of 2 RF_753, Issue 2 24-05-2024 Waev Technologies, Inc. U.S. Agent Designation for Service of Process (Applicant and U.S. Agent are Separate Parties) TO: Kiwa Nederland B.V. Wilmersdorf 50 7327 AC Apeldoorn Postbus 137 7300 AC Apeldoorn Netherlands ATTENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company name: Waev Technologies, Inc. FRN: 0034928887 Contact person name: Jake Corday Street address: 2013 Stream View ct. ZIP/City/State 28173 Charlotte NC Telephone number: +17048197940 Email address: [email protected] Signature: Date: 2024 -05-24 This letter is to confirm that we (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission- related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Waev Technologies, Inc. Grantee Code: 2BFMW Contact person name: Jake Corday Street address: 2013 Stream View ct. ZIP/City/State 28173 Charlotte NC Telephone number: +17048197940 Email address: [email protected] Signature: Date: 2024 -05-24

Covered list attestation FCC application letter Kiwa Page 1 of 2 RF_75 5_02 24- 05-2024 Waev Technologies, Inc. 2013 Stream View ct. 28173 Charlotte NC Certification Application Attestation Statements <Waev Technologies, Inc.> Waev Technologies, Inc. 2013 Stream View ct. 28173 Charlotte NC Subject: FCC ID: <2BFMW-20240220> To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) [Made Studio] certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> Statement for 47 CFR section 2.911(d)(5)(ii) [Made Studio] (“the applicant”) certifies that, as of the date of the filing of this application, the applicant - is / - is not (3) identified on the Covered List as an entity producing “covered” equipment. Date: 2024/05/24 City: 28173 Charlotte NC Name : Jake Corday Function: Digital signage Telephone number: +17048197940 Email address: [email protected] Signature: 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . (2): For FCC it must be the Grantee Code “owner” or the authorized agent. (3): double click on the appropriate box and select ‘’checked” then “OK”

RF_160_05 Declaration of Authorisation Date of issue 24- 05-2024 (On manufacturer’s company letter heading) Declaration of Authorization We Name: Waev Technologies, Inc. Address: 2013 Stream View ct. City: 28173 Charlotte NC Country: USA Declare that: Name Representative of agent: Jessy Lin Agent Company name: Worldwide Testing Services (Taiwan) Co., Ltd Address: 6F., No. 58, Lane 188, Ruey Kuang Road, Neihu district, City: Taipei 114, Country Taiwan is authorized to apply for Certification of the following product(s): Product description: Bar Display Type designation: Bar Display Trademark: Waev Validity/ expiry date on our behalf. Date: 2024/05/24 City: 28173 Charlotte NC Name: Jake Corday Function: Digital Signage Signature: ............................... Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

FCC, Request for non-disclosure Date: 24-05-2024 RF_501, Issue 10 Company Name: Waev Technologies, Inc. Address : 2013 Stream View ct. City: 28173 Charlotte NC Country: USA To: Kiwa Netherlands B.V., Dept. FCC TCB Wilmersdorf 50 7327 AC Apeldoorn The Netherlands Subject: Request for confidentiality FCC ID: 2BFMW-20240220 Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, a pplicant hereby requests Short-Term Confidential treatment of the following materials (See notes below): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Date: 2024/05/24 Name and signature of applicant: Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! The planned date should state in the RF731 application form. 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Kiwa NL B.V. at least 7 days before date of actual marketing or before expiration of the STC period Jake Corday

of Applicant: Made Studio Design Ltd. Address: 10F., No. 169, Sec. 4, Zhongxiao E. Rd., Da-an Dist., Taipei City 10690, Taiwan Tested and Prepared by Worldwide Testing Services (Taiwan) Co., Ltd. FCC Registration No.: TW1477, TW1072 Industry Canada filed test laboratory Reg. No.: 20037, 5107A Report No.: W6M22301-22424-EE 6F, NO. 58, LANE 188, RUEY-KUANG RD., NEIHU TAIPEI 114, TAIWAN, R.O.C. TEL: 886-2-66068877 FAX: 886-2-66068879 E-mail: [email protected] FCC RF Exposure Exemption report for Bar Display Model No.: Bar Display FCC ID: 2BFMW-20240220 Registration number: W6M22301-22424-EE FCC ID: 2BFMW-20240220 Worldwide Testing Services(Taiwan) Co., Ltd. Page 1 of 11 TABLE OF CONTENTS 1 GENERAL INFORMATION .......................................................................................................... 2 1.1 NOTES .......................................................................................................................................... 2 1.2 TESTING LABORATORY ................................................................................................................ 3 1.2.1 Location .................................................................................................................................. 3 1.2.2 Details of accreditation status ................................................................................................ 3 1.3 A PPLICATION DETAILS ................................................................................................................. 3 1.4 G ENERAL INFORMATION OF TEST ITEM ........................................................................................ 4 1.5 D UTY CYCLE AND FACTOR ........................................................................................................... 5 1.6 T EST STANDARDS ......................................................................................................................... 8 2 TEST CONFIGURATION .............................................................................................................. 9 2.1 TEST ENVIRONMENT .................................................................................................................... 9 2.2 M EASUREMENT UNCERTAINTY .................................................................................................... 9 2.3 TEST EQUIPMENT LIST ................................................................................................................. 9 3 EXEMPTION LIMITS FOR ROUTINE EVALUATION ........................................................ 10 Registration number: W6M22301-22424-EE FCC ID: 2BFMW-20240220 Worldwide Testing Services(Taiwan) Co., Ltd. Page 2 of 11 1 General Information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has passed all the relevant tests conforms to a specification. Neither is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that is performance generally conforms to representative cases of communications equipment. Laboratory disclaimer- 1. The test results of this test report relate exclusively to the item tested as specified in 1.5. 2. The test report may only be reproduced or published in full. 3. Reproduction or publication of extracts from the report requires the prior written approval of the Worldwide Testing Services(Taiwan) Co., Ltd. 4. Antenna gain is provided by applicant and laboratory issue relevant data and results. Tester: April 11, 2024 Brian NG Date WTS-Lab. Name Signature Technical responsibility for area of testing: April 11, 2024 Kevin Wang Date WTS Name Signature Registration number: W6M22301-22424-EE FCC ID: 2BFMW-20240220 Worldwide Testing Services(Taiwan) Co., Ltd. Page 3 of 11 1.2 Testing laboratory 1.2.1 Location 10m OATS No.5-1, Lishui, Shuang Sing Village, Wanli Dist., New Taipei City 207, Taiwan (R.O.C.) 3 meter semi-anechoic chamber No.35, Aly. 21, Ln. 228, Ankang Rd., Neihu Dist., Taipei City 114, Taiwan (R.O.C.) Tel: 886-2-6613-0228 Worldwide Testing Services (Taiwan) Co., Ltd. 6F., No. 58, Ln. 188, Ruiguang Rd., Neihu Dist., Taipei City 114 , Taiwan (R.O.C.) Tel: 886-2-6606-8877 1.2.2 Details of accreditation status Accredited testing laboratory FCC filed test laboratory Reg. No.: TW1477, TW1072 Industry Canada filed test laboratory Reg. No.: 20037, 5107A Test location, where different from Worldwide Testing Services (Taiwan) Co., Ltd. : Name: ./. Accredited no.: ./. Street: ./. Town: ./. Country: ./. 1.3 Application details Approval holder Name: Made Studio Design Ltd. Street: 10F., No. 169, Sec. 4, Zhongxiao E. Rd., Da-an Dist., Town: Taipei City 10690, Country: Taiwan Manufacturer: (if applicable) Name: ./. Street: ./. Town: ./. Country: ./. Registration number: W6M22301-22424-EE FCC ID: 2BFMW-20240220 Worldwide Testing Services(Taiwan) Co., Ltd. Page 4 of 11 Date of receipt of test item: September 19, 2023 Date of test: from September 20, 2023 to November 28, 2023 1.4 General information of Test item Type of test item: Bar Display Model no.: Bar Display Multi-listing model no.: ./. Brand name: Waev Power supply: Battery 11.1Vd.c., 7800mAh, 86.58Wh Battery Charger (I/P: 100-240V 50/60Hz, O/P: 12.6V⎓2A) Type of antenna: Chip Antenna Antenna gain: 2.29 dBi Technical data WLAN Mode Channel Conducted Power (dBm) 802.11b Ch 1 : 2412 MHz 15.05 Ch 6 : 2437 MHz 15.33 Ch 11 : 2462 MHz 15.49 802.11g Ch 1 : 2412 MHz 13.25 Ch 6 : 2437 MHz 13.44 Ch 11 : 2462 MHz 13.68 802.11n20MHz Ch 1 : 2412 MHz 12.58 Ch 6 : 2437 MHz 12.84 Ch 11 : 2462 MHz 13.05…

Text truncated - open the document above for the full version.

承 認 書 SPECIFICATION FOR APPROVAL 客戶名稱 CUSTOMER ： 客戶料號 CUSTOMER’S P/N ： 料號 PART NUMBER ： WAN7020L245M04 規格 DESCRIPTION ： Chip Antenna 7020 M-Ant 2.45G Type 04 版本 VERSION ： V1.1 日期 ISSUE DATE ： 2020/03/13 客 戶 承 認 CUSTOMER APPROVED 工 程 部 R&D CENTER 承 認 APPROVAL 確 認 CHECKED 製 作 DRAWN Ray Tennyson Snow 萬誠科技股份有限公司 OneWave Electronic Co., Ltd. 112台北市北投區立功街151號1樓 1F, No. 151, Li Gong Street, Beitou District, Taipei City 112, Taiwan 電話: (02) 2898-2220 TEL: +886 2 2898-2220 傳真: (02) 2898-5055 FAX: +886 2 2898-5055 2/11 ONEWAVE TECHNOLOGY CO., LTD. 7020 Chip antenna For Bluetooth / WLAN Applications Dimension (mm) L 7.00 ± 0.20 W 2.00 ± 0.20 T 1.95 ± 0.20 P/N: WAN7020L245M04 3/11 ONEWAVE TECHNOLOGY CO., LTD. Part Number Information WAN 7020 L 245 M 04 A B C D E F A Product Series Antenna B Dimension L x W 7.0X2.0mm (+-0.2mm) C Material High K material D Working Frequency 2.4 ~ 2.5GHz E Feeding mode Monopole & Single Feeding F Antenna type Type = 04 1. Electrical Specification Remark : Bandwidth & Peak Gain was measured under evaluation board of next page Specification Part Number WAN7020L245M04 Central Frequency 2450 MHz Bandwidth 170 (Min.) MHz Return Loss -10 (Max) dB Peak Gain 3.64 dBi Impedance 50 Ohm Operating Temperature -40～+110 °C Maximum Power 4 W Resistance to Soldering Heats 10 ( @ 260°C) sec. Polarization Linear Azimuth Beamwidth Omni-directional Termination Cu / Sn (Leadless) 4/11 ONEWAVE TECHNOLOGY CO., LTD. 2. Recommended PCB Pattern Evaluation Board Dimension Unit : mm Suggested Matching Circuit 重要資訊 : 匹配元件建議使用精準度高的電感±0.1~0.3nH、電容±0.1pF 5/11 ONEWAVE TECHNOLOGY CO., LTD. ◆ Layout Dimensions in Clearance area ( Size=10.0*5.0mm) Matching circuit FootPrint (Unit : mm) 6/11 ONEWAVE TECHNOLOGY CO., LTD. 3. Measurement Results Return Loss 7/11 ONEWAVE TECHNOLOGY CO., LTD. Radiation Pattern Efficiency Peak Gain 2400MHz 73.40% 3.11 dBi 2450MHz 78.06 % 3.64 dBi 2500MHz 71.20 % 2.88 dBi Chamber Coordinate System Y Z X 8/11 ONEWAVE TECHNOLOGY CO., LTD. 4.Reliability and Test Condictions ITEM REQUIREMENTS TEST CONDITION Solderability 1. Wetting shall exceed 90% coverage 2. No visible mechanical damage Pre-heating temperature:150°C/60sec. Solder temperature:230±5°C Duration:4±1sec. Solder:Sn-Ag3.0-Cu0.5 Flux for lead free: rosin Solder heat Resistance 1. No visible mechanical damage 2. Central Freq. change :within ± 6% 10 ± 0.5 sec. 60 sec . . T E M P ( °C ) 150 °C 2 6 0 °C Pre-heating temperature:150°C/60sec. Solder temperature:260±5°C Duration:10±0.5sec. Solder:Sn-Ag3.0-Cu0.5 Flux for lead free: rosin Component Adhesion (Push test) 1. No visible mechanical damage The device should be reflow soldered(230±5°C for 10sec.) to a tinned copper substrate A dynometer force gauge should be applied the side of the component. The device must with-ST-F 0.5 Kg without failure of the termination attached to component. Component Adhesion (Pull test) 1. No visible mechanical damage Insert 10cm wire into the remaining open eye bend ,the ends of even wire lengths upward and wind together. Terminal shall not be remarkably damaged. Thermal shock 1. No visible mechanical damage 2. Central Freq. change :within ±6% Phase Temperature(°C) Time(min) 1 +110±5°C 30±3 2 Room Temperature Within 3sec 3 -40±2°C 30±3 4 Room Temperature Within 3sec +110°C=>30±3min -40°C=>30±3min Test cycle:10 cycles The chip shall be stabilized at normal condition for 2~3 hours before measuring. Resistance to High Temperature 1. No visible mechanical damage 2. Central Freq. change :within ±6% 3. No disconnection or short circuit. Temperature: +110±5°C Duration: 1000±12hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. Resistance to Low Temperature 1. No visible mechanical damage 2. Central Freq. change :within ±6% 3. No disconnection or short circuit. Temperature:-40±5°C Duration: 1000±12hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. Humidity 1. No visible mechanical damage 2. Central Freq. change :within ±6% 3. No disconnection or short circuit. Temperature: 40±2°C Humidity: 90% to 95% RH Duration: 1000±12hrs The chip shall be stabilized at normal condition for 2~3 hours before measuring. 4±1 sec. 60sec TEMP (°C) 150°C 230°C 9/11 ONEWAVE TECHNOLOGY CO., LTD. 5.Soldering and Mounting Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. The terminations are suitable for all wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. Recommended temperature profiles for re-flow soldering in Figure 1. Products attachment with a soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. ‧Preheat circuit and products to 150°C ‧Never contact the ceramic with the iron tip ‧Use a 20 watt soldering iron with tip diameter of 1.0mm ‧280°C tip temperature (max) ‧1.0mm tip diameter (max) ‧Limit soldering time to 3 sec. SOLDERING COOLING NATURAL PRE-HEATING TEMPERATURE(°C) 60~120 s 10s max. 30~60s 250~260 230 180 150 TIME(sec.) Reflow Soldering SOLDERING COOLING NATURAL PRE-HEATING TEMPERATURE(°C) within 3s Gradual cooling 150 TIME(sec.) Iron Soldering Over 60s 350 300 10/11 ONEWAVE TECHNOLOGY CO., LTD. 6.Packaging Information ◆ Tape Specification: ◆ Reel Specification: (7’’, Φ180 mm) Tape Width(mm) A(mm) B(mm) C(mm) D(mm) Chip/Reel(pcs) 12 12±1.0 60±2 13.5±0.5 178±2 2000 11/11 ONEWAVE TECHNOLOGY CO., LTD. 7.Storage and Transportation Information Storage Conditions To maintain the solderability of terminal electrodes: 1. Temperature and humidity conditions: -10~ 40°C and 30~70% RH. 2. Recommended products should be used within 6 months from the time of delivery. 3. The packaging material should be kept where no chlorine or sulfur exists in the air…

Text truncated - open the document above for the full version.

of Applicant: Waev Technologies, Inc. Address: 10F, No.169, Section 4, Zhongxiao E Rd Da-an District, Taipei City 10690, Taiwan Tested and Prepared by Worldwide Testing Services (Taiwan) Co., Ltd. FCC Registration No.: TW1477, TW1072 Industry Canada filed test laboratory Reg. No.: 20037, 5107A Report No.: W6M22301-22424-C-1 6F, NO. 58, LANE 188, RUEY-KUANG RD., NEIHU TAIPEI 114, TAIWAN, R.O.C. TEL: 886-2-66068877 FAX: 886-2-66068879 E-mail: [email protected] 47 CFR PART 15 SUBPART C TEST REPORT for Bar Display Model No.: Bar Display FCC ID: 2BFMW-20240220 Registration number: W6M22301-22424-C-1 FCC ID: 2BFMW-20240220 Worldwide Testing Services(Taiwan) Co., Ltd. Page 1 of 40 TABLE OF CONTENTS 1 GENERAL INFORMATION .......................................................................................................... 2 1.1 NOTES .......................................................................................................................................... 2 1.2 TESTING LABORATORY ................................................................................................................ 3 1.2.1 Location .............................................................................................................................. 3 1.2.2 Details of accreditation status ............................................................................................ 3 1.3 APPLICATION DETAILS ................................................................................................................. 3 1.4 G ENERAL INFORMATION OF TEST ITEM ........................................................................................ 4 1.5 D UTY CYCLES .............................................................................................................................. 5 1.6 TEST STANDARDS ......................................................................................................................... 8 2 TECHNICAL TEST ......................................................................................................................... 9 2.1 S UMMARY OF TEST RESULTS ........................................................................................................ 9 2.2 TEST ENVIRONMENT .................................................................................................................... 9 2.3 TEST EQUIPMENT LIST .................................................................................................................. 10 3 TEST RESULTS (ENCLOSURE) ................................................................................................ 12 3.1 PEAK OUTPUT POWER (TRANSMITTER) ...................................................................................... 13 3.2 S PURIOUS EMISSIONS RADIATED – TRANSMITTER OPERATING ................................................... 19 3.3 EMISSIONS IN NONRESTRICTED FREQUENCY BANDS ................................................................... 22 3.4 MINIMUM 6 DB BANDWIDTH ..................................................................................................... 26 3.5 PEAK POWER SPECTRAL DENSITY ............................................................................................. 32 3.6 P OWER LINE CONDUCTED EMISSION ......................................................................................... 33 APPENDIX .............................................................................................................................................. 40 Registration number: W6M22301-22424-C-1 FCC ID: 2BFMW-20240220 Worldwide Testing Services(Taiwan) Co., Ltd. Page 2 of 40 1 General Information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has passed all the relevant tests conforms to a specification. Neither is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that is performance generally conforms to representative cases of communications equipment. Laboratory disclaimer- 1. The test results of this test report relate exclusively to the item tested as specified in 1.5. 2. The test report may only be reproduced or published in full. 3. Reproduction or publication of extracts from the report requires the prior written approval of the Worldwide Testing Services(Taiwan) Co., Ltd. 4. Antenna gain is provided by applicant and laboratory issue relevant data and results. Specific Conditions: Usage of the hereunder tested device in combination with other integrated or external antennas requires at least additional output power measurements, spurious emission measurements, conducted emission measurements (AC supply lines) and radio frequency exposure evaluations for each individual configuration performed, for certification by FCC. The test sample is able to work according IEEE 802.11 b/g/n. This report is related to FCC Part 15 C (DSSS and OFDM device). Tester: May 24, 2024 Brian NG Date WTS-Lab. Name Signature Technical responsibility for area of testing: May 24, 2024 Kevin Wang Date WTS Name Signature Registration number: W6M22301-22424-C-1 FCC ID: 2BFMW-20240220 Worldwide Testing Services(Taiwan) Co., Ltd. Page 3 of 40 1.2 Testing laboratory 1.2.1 Location 10m OATS No.5-1, Lishui, Shuang Sing Village, Wanli Dist., New Taipei City 207, Taiwan (R.O.C.) 3 meter semi-anechoic chamber No.35, Aly. 21, Ln. 228, Ankang Rd., Neihu Dist., Taipei City 114, Taiwan (R.O.C.) Tel: 886-2-6613-0228 Worldwide Testing Services (Taiwan) Co., Ltd. 6F., No. 58, Ln. 188, Ruiguang Rd., Neihu Dist., Taipei…

Text truncated - open the document above for the full version.