2BFZ6-1Stadia Neptune

Stadia Neptune Operation The Stadia Neptune device uses 24GHz Radar to collect distance data. This distance data is sent via Bluetooth to the user’s smartphone and interpreted within a purpose-built app. The Stadia Neptune device consists of 4 main parts: Radar, Li-ion batteries, microcontroller with Bluetooth, and an on/off switch. When the switch is flipped up to the “On” position, LEDs on the Microcontroller will light up. The device is programmed so that as soon as it is powered, both the Bluetooth and the Radar will immediately begin radiating energy in their respective wavelengths. The Microcontroller is based on the Espressif ESP32 circuit board. The Radar is based on the uRAD 24GHz radar from Anteral. After the device is switched “Off”, the device will not power back on for 30 seconds, regardless of the switch position (this is a quirk of the Microcontroller software). To turn the device back on, leave the switch in the “Off” position for at least 30 seconds, and then switch it to the “On” position. Recharging the device is done through a micro-USB cord via the microcontroller. Battery power is indicated via 4 LEDs on the microcontroller, with the battery percentage labeled next to each LED (25%, 50%, 75%, 100% [green]) FCC STATEMENT: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

- SkeeterEnterprises- FederalCommunicationsCommission Authorizationand EvaluationDivision EquipmentAuthorizationBranch 7435 OaklandMills Road Columbia,MD 21046 4/24/24 U.S. AgentDesignation [SkeeterEnterprises]acknowledgestheir consentfor the followingcontactlocatedin the UnitedStatesto act as their agent for serviceof processfor the equipmentfor which authorizationis sought(FCC ID:[2BFZ6-1]): Nameand companyof U.S. agent:LinkwldLLC PhysicalU.S. addressof agent:1942 BroadwaySt. STE 314C,Boulder,CO, 80302,US FRN of U.S. agent:0033625682 Email addressof U.S. agent:[email protected] LinkwldLLC acknowledgestheir obligationto acceptserviceof processon behalfof[SkeeterEnterprises]. [SkeeterEnterprises]with the FRN[0035317189]acceptsits obligationto maintainan agentfor serviceof processin the UnitedStatesfor no less than one year after eitherthe granteehas permanentlyterminatedall marketingand importationof the applicableequipmentwithinthe U.S., or the conclusionof any Commission- relatedadministrativeor judicialproceedinginvolvingthe equipment,whicheveris later. By signingthis form, we confirmthe aboveand that we are awareof the applicationrequirementslisted under§ 2.911(d)(7). The informationprovidedin this letter is basedon the referencedrule parts of Title 47 of the CFR as well as KDB 986446D01. An expirationdate for this letter does not exist. In case the U.S. agent changes,the granteeis obligatedto notify the FCC within 30 days via the grantingTCB. Sincerely, Signature [Name]Sean Sherman [Title] Owner [Company]SkeeterEnterprises Signature [Nameof U.S. agent]TimothyZhu [Title of U.S. agent]Manager [Companyof U.S. agent]LinkwldLLC 48_[model] US_Agent_2.911(d)(7)-U, V05

C5266091_X24_Ed.2 1/1 “Attestation Statements” TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Skeeter Enterprises Grantee code: 2BFZ6 FRN: 0035317189 FCC ID: 2BFZ6B-1 Contact Name: Sean Sherman Address: 8184 Compass Pointe E Wynd NE, Leland, North Carolina, 28451, United States Telephone No: 1-218-398-0598 Fax No: 844-897-7168 Email: [email protected] i. Skeeter Enterprises (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. Skeeter Enterprises (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. Skeeter Enterprises certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Date: 2024/05/28 Applicant’s Name: Sean Sherman Title: Owner Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

C5266091_X8_Ed.1 1/1 Letter of Authorization Skeeter Enterprises Company: Skeeter Enterprises Address: 8184 Compass Pointe E Wynd NE, Leland, North Carolina, 28451, United States Product Name: Stadia Neptune Model Number: 1 FCC Identifier: 2BFZ6-1 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Sean Sherman Date: 2024.05.28 Title: Owner Signature of applicant:

C5266091_X10_Ed.2 1/1 Skeeter Enterprises Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2024.05.28 Subject: Request for Confidentiality FCC ID: 2BFZ6-1 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. C5266091_X10_Ed.2 1/1 Sincerely, Signature: Name: Sean Sherman Title: Owner

ProjectNo.:18220WC400769Page 1 of 3 AppendixII--ExternalPhotograph ProjectNo.:18220WC400769Page 2 of 3 ProjectNo.:18220WC400769Page 3 of 3

LabelLocationOnEUT Label ProductName:StadiaNeptune ModelNo.:1 FCCID:2BFZ6-1 ThisdevicecomplieswithPart15oftheFCCRules.Operation issubjecttothefollowingtwoconditions: Thisdevicemaynotcauseharmfulinterference,and Thisdevicemustacceptanyinterferencereceived,including interferencethatmaycauseundesiredoperation.

ProjectNo.:18220WC400769Page 1 of 5 AppendixIII--InternalPhotograph ProjectNo.:18220WC400769Page 2 of 5 24.005GHz-24.245GHz ANT ProjectNo.:18220WC400769Page 3 of 5 ProjectNo.:18220WC400769Page 4 of 5 ProjectNo.:18220WC400769Page 5 of 5 BTANT

NOTE: This document is issued by Shenzhen Morlab Communications Technology Co., Ltd., the test report shall not be reproduced except in full without prior written permission of the company. The test results apply only to the particular sample(s) tested and to the specific tests carried out which is available on request for validation and information confirmed at our website. MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] Page 1 of 9 REPORT No.：SZ24040353S01 RF EXPOSURE EVALUATION REPORT APPLICANT : Skeeter Enterprises PRODUCT NAME : Stadia Neptune MODEL NAME : 1 BRAND NAME : N/A FCC ID : 2BFZ6-1 STANDARD(S) : FCC 47 CFR Part 2(2.1093) RECEIPT DATE : 2024-04-20 TEST DATE : 2024-04-23 to 2024-04-30 ISSUE DATE : 2024-06-07 Edited by: Zeng Xiaoying (Rapporteur) Approved by: Shen Junsheng (Supervisor) MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ24040353S01 Page 2 of 9 DIRECTORY 1. Technical Information········································································································ 3 1.1 Applicant and Manufacturer Information ····································································· 3 1.2 Equipment under Test (EUT) Description ···································································· 3 1.3 Applied Reference Documents ····················································································· 4 2. Device Category and RF Exposure Limit ······································································· 5 3. Maximum Average Power (Strength) Summary····························································· 6 4. RF Exposure Assessment ································································································ 7 Annex A General Information ································································································· 9 Change History Version Date Reason for Change 1.0 2024-06-07 First edition MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ24040353S01 Page 3 of 9 1. Technical Information Note: Provide by applicant. 1.1 Applicant and Manufacturer Information Applicant: Skeeter Enterprises Applicant Address: 8184 Compass pointe E Wynd NE, Leland, NC 28451 Manufacturer: Anteral Manufacturer Address: Calle Tajonar 22. 31006, Pamplona Spain 1.2 Equipment under Test (EUT) Description Product Name: Stadia Neptune Serial No.: (N/A, marked #1 by test site) Hardware Version: N/A Software Version: N/A Frequency Range: Bluetooth: 2402 – 2480 MHz Radar: 24.005 – 24.245 GHz Modulation Type: Bluetooth: GFSK Note: When the test result is a critical value, we will use the measurement uncertainty give the judgment result based on the 95% risk level. MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ24040353S01 Page 4 of 9 1.3 Applied Reference Documents Leading reference documents for testing: Identity Document Title Method determination /Remark FCC 47 CFR Part 2(2.1093) Radio Frequency Radiation Exposure Assessment: Portable devices No deviation KDB 447498 D01v06 General RF Exposure Guidance No deviation Note: Additions to, deviation, or exclusions from the method shall be judged in the "method determination" column of add, deviate or exclude from the specific method shall be explained in the "Remark" of the above table. MORLAB Shenzhen Morlab Communications Technology Co., Ltd. FL.1-3, Building A, FeiYang Science Park, No.8 LongChang Road, Block67, BaoAn District, ShenZhen , GuangDong Province, P. R. China Tel: 86-755-36698555 Fax: 86-755-36698525 Http://www.morlab.cn E-mail: [email protected] REPORT No.：SZ24040353S01 Page 5 of 9 2. Device Category and RF Exposure Limit Per user manual, based on 47 CFR 2.1093, this device belongs to portable device category with General Population/Uncontrolled exposure.  Portable Devices: 47 CFR 2.1093(b) For purposes of this section, a portable device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance within 20 centimeters is normally maintained between the transmitter's radiating structure(s) and the body of the user or nearby persons. In this context, the term “fixed location” means that the device is physically secured at one location and is not able to be easily moved to another location.  General Population/Uncontrolled Exposure limit: The general population/uncontrolled exposure limits are applicable to situations in which the general public may be exposed or in which persons who are exposed as a consequence of their employment may not be made fully aware of the potential for exposure or cannot exercise control over their exposure. Members of the general public would come under this category when exposure is not employment-related; for example, in the case of a wireless transmitter that exposes persons in its vicinity. Warning labels placed on low-power consumer devices such as cellular telephones are not considered sufficient to allow the device to be considered under the occupational/controlled category, and the general po…

Text truncated - open the document above for the full version.

RFEXPOSUREEVALUATION FCCID:2BFZ6-1 AccordingtoKDB447498D01MobileandPortableDevicesRFExposureProcedures andEquipmentAuthorizationPoliciesv06. AccordingtoFCC1.1310:Thecriterialistedinthefollowingtableshallbeused toevaluatetheenvironmentimpactofhumanexposuretoradiofrequency(RF) Radiationasspecifiedin§1.1307(b): RoutineSARevaluationreferstothatspecificallyrequiredby§2.1093,using measurementsorcomputersimulation.WhenroutineSARevaluationisnot required,portabletransmitterswithoutputpowergreaterthantheapplicable lowthresholdrequireSARevaluationtoqualifyforTCBapproval. Channel (MHz) Maximum output power (dBm) Tuneup tolerance (dBm) MaxTune UpPower (dBm) Distanc e(mm) Calculation results Limit Operating Mode 24020.160.16±11.1650.4053 GFSK24400.620.62±11.6250.4543 24800.510.51±11.5150.4463 Result:NoStandaloneSARtestisrequired.

SmallSize2.4GHzPCBAntenna-AN043 1DATASHEETKEYWORDS ThePCBantennaDescription TheManufacturerInformation 2TESTINTRODUCTION ThePCBantennadescribedinthisapplicationnoteisnowusedonESP8266modulereference design.However,itcanalsobeusedinall2.4GHzdesigns,especiallysmallspaceisrequiredfor theantenna. Figure1:ESP8266Module AntennaName:AN043 ModelNumber:AN043 MaximumGain:2dBi AntennaType:PCBAntenna OperationFrequency:2400~2500MHz ManufacturerName:EspressifSystems ManufacturerAddress: #101,Block2,690BiboRoad,ZhangJiangHiJiangShanghai,China 2.1LayoutandImplementation Smallchangesoftheantennadimensionsmayhavelargeimpactontheperformance.Thereforeit isstronglyrecommendedtomakeanexactcopyofthereferencedesigntoachieveoptimum performance.ItisalsorecommendedtousethesamethicknessandtypeofPCBmaterialasused inthereferencedesign. Figure2:AntennaDimensions L13.94 L22.70 L35.00 L42.64 L52.00 L64.90 W10.90 W20.50 D10.50 D20.30 D30.30 D40.50 D51.40 D61.70 Table1:AntennaDimensions(Unit:mm) 4TESTRESULTS Reflection,radiationpatternweremeasuredtoverifytheperformanceofthePCBantenna. 4.1Reflection Allthereflectionmeasurementswereperformedwithanetworkanalyzerconnectedtoasemi- rigidcoaxcable,whichwassolderedtothefeedpointoftheantenna.Becauseofthesmallsize antennaandthesmallgroundplanethiskindofmeasurementsisheavilyaffectedbythepresence andplacementofthecoaxcable.Thisinfluencecanresultinasmalluncertaintyinresonance frequencyandmeasuredreflection.Typicallydifferentplacementofthesemi-rigidcoaxcable couldchangetheresonancefrequencywith5-10MHzandthereflectionwith3-4dB. Figure3:InfluenceofPlasticEncapsulationandTestPins ThesizeofthegroundplaneaffectstheperformanceofthePCBantenna.SolderingESP8266toa testboardincreasesthesizeofthegroundplaneandthustheperformanceisaffected.However, bandwidthstillcanbeenoughtocoverthewhole2.4GHzISMband. 4.2RadiationPattern TheradiationpatternfortheantennaimplementedontheESP8266referencedesignhasbeen measuredinanLabchamber.Figure4throughFigure7showsmaximumvalueradiationpatterns forthreeplanes,XY,XZandYZ,measuredwithverticalandhorizontalpolarizationfrom 2400MHz~2500MHzfrequencyrange.Allmeasurementswereperformedwith0dBmoutput power. Figure4:HowtoRelatetheAntennatotheRadiationPatterns 4.3MaximumGain ThefollowingtableliststheMaximumGainoftheantenna.Thefreelineofsight(LOS)rangewas measuredwith250kbpsand1%PER 2440MHz: 2 dBi . Maximum Gain2.0 dBi LOS range240 m Antenna Size15.2 x 5.7 mm

ReportNo.:18220WC40076901FCCID:2BFZ6-1Page1of30 FCCTestReport Applicant:SkeeterEnterprises Address: 8184CompassPointeEWyndNE,Leland,North Carolina,28451,UnitedStates ProductName:StadiaNeptune ReportDate:May25,2024 ShenzhenAnbotekComplianceLaboratoryLimited ReportNo.:18220WC40076901FCCID:2BFZ6-1Page2of30 Contents 1.GeneralInformation.................................................................................................................................6 1.1.ClientInformation...........................................................................................................................6 1.2.DescriptionofDevice(EUT)..........................................................................................................6 1.3.AuxiliaryEquipmentUsedDuringTest..........................................................................................7 1.4.Operationchannellist....................................................................................................................7 1.5.DescriptionofTestModes.............................................................................................................7 1.6.MeasurementUncertainty.............................................................................................................8 1.7.TestSummary................................................................................................................................8 1.8.DescriptionofTestFacility.............................................................................................................9 1.9.Disclaimer......................................................................................................................................9 1.10.TestEquipmentList...................................................................................................................10 2.Antennarequirement..............................................................................................................................12 2.1.Conclusion...................................................................................................................................12 3.ConductedEmissionatACpowerline..................................................................................................13 3.1.EUTOperation.............................................................................................................................13 3.2.TestSetup....................................................................................................................................13 3.3.TestData......................................................................................................................................14 4.OccupiedBandwidth..............................................................................................................................16 4.1.EUTOperation.............................................................................................................................16 4.2.TestSetup....................................................................................................................................16 4.3.TestData......................................................................................................................................16 5.MaximumConductedOutputPower......................................................................................................17 5.1.EUTOperation.............................................................................................................................17 5.2.TestSetup....................................................................................................................................17 5.3.TestData......................................................................................................................................17 6.PowerSpectralDensity..........................................................................................................................18 6.1.EUTOperation.............................................................................................................................18 6.2.TestSetup....................................................................................................................................18 6.3.TestData......................................................................................................................................18 7.Emissionsinnon-restrictedfrequencybands.......................................................................................19 7.1.EUTOperation.............................................................................................................................19 7.2.TestSetup....................................................................................................................................19 7.3.TestData......................................................................................................................................19 8.Bandedgeemissions(Radiated)..........................................................................................................20 8.1.EUTOperation.............................................................................................................................20 8.2.TestSetup....................................................................................................................................20 8.3.TestData......................................................................................................................................21 9.Emissionsinfrequencybands(below1GHz).......................................................................................22 9.1.EUTOperation.............................................................................................................................22 9.2.TestSetup...........................................................................…

Text truncated - open the document above for the full version.

Page1of13 AppendixTestData ReportNo.:18220WC40076901TestSampleNo.:1-2-2 StartTestDate:2024.4.18FinishTestDate:2024.4.18 TestEngineer:Auditor: Temperature:25.5 °C RelativeHumidity:47% Pressure:101kPa AppendixA:-6dBBandwidth ConditionAntennaRateFrequency(MHz)-6dBBW(kHz)limit(kHz)Result NVNTANT11Mbps2402512.51500Pass NVNTANT11Mbps2440524.54500Pass NVNTANT11Mbps2480524.54500Pass -6dB_Bandwidth_NVNT_ANT1_1Mbps_2402 -6dB_Bandwidth_NVNT_ANT1_1Mbps_2440 Page2of13 -6dB_Bandwidth_NVNT_ANT1_1Mbps_2480 Page3of13 AppendixB:99%OccupiedBandwidth ConditionAntennaRateFrequency(MHz)99%%BW(MHz) NVNTANT11Mbps24021.049 NVNTANT11Mbps24401.091 NVNTANT11Mbps24801.127 99%_Occupied_Bandwidth_NVNT_ANT1_1Mbps_2402 99%_Occupied_Bandwidth_NVNT_ANT1_1Mbps_2440 Page4of13 99%_Occupied_Bandwidth_NVNT_ANT1_1Mbps_2480 Page5of13 AppendixC:Bandedge ConditionAntennaRate TX_Frequency (MHz) Max.Mark Frequency(MHz) Spurious level(dBm) limit(dBm)Result NVNTANT11Mbps24022378.569-48.474-19.991Pass NVNTANT11Mbps24802491.146-48.930-19.687Pass 1_Reference_Level_NVNT_ANT1_1Mbps_2402 2_Bandedge_NVNT_ANT1_1Mbps_2402 Page6of13 1_Reference_Level_NVNT_ANT1_1Mbps_2480 2_Bandedge_NVNT_ANT1_1Mbps_2480 Page7of13 AppendixD:PeakOutputPower ConditionAntennaRate Frequency (MHz) Max.Conducted Power(dBm) Max.Conducted Power(mW) Limit(mW)Result NVNTANT11Mbps24020.161.041000Pass NVNTANT11Mbps24400.621.151000Pass NVNTANT11Mbps24800.511.131000Pass Peak_Output_Power_NVNT_ANT1_1Mbps_2402 Peak_Output_Power_NVNT_ANT1_1Mbps_2440 Page8of13 Peak_Output_Power_NVNT_ANT1_1Mbps_2480 Page9of13 AppendixE:PowerSpectralDensity ConditionAntennaRate Frequency (MHz) PowerSpectral Density(dBm) Limit(dBm/3kHz)Result NVNTANT11Mbps2402-20.178Pass NVNTANT11Mbps2440-20.268Pass NVNTANT11Mbps2480-20.358Pass Power_Spectral_Density_NVNT_ANT1_1Mbps_2402 Power_Spectral_Density_NVNT_ANT1_1Mbps_2440 Page10of13 Power_Spectral_Density_NVNT_ANT1_1Mbps_2480 Page11of13 AppendixF:SpuriousEmission ConditionAntennaRateTX_Frequency(MHz) Spurious MAX.Value(dBm) LimitResult NVNTANT11Mbps2402-42.947-19.991Pass NVNTANT11Mbps2440-43.185-19.559Pass NVNTANT11Mbps2480-42.633-19.687Pass 1_Reference_Level_NVNT_ANT1_1Mbps_2402 2_Spurious_Emission_NVNT_ANT1_1Mbps_2402 Page12of13 1_Reference_Level_NVNT_ANT1_1Mbps_2440 2_Spurious_Emission_NVNT_ANT1_1Mbps_2440 1_Reference_Level_NVNT_ANT1_1Mbps_2480 Page13of13 2_Spurious_Emission_NVNT_ANT1_1Mbps_2480 ---End---

ProjectNo.:18220WC400769Page 1 of 2 AppendixI--TestSetupPhotograph_RF ConductedEmissionatACpowerline Emissionsinfrequencybands(below1GHz) ProjectNo.:18220WC400769Page 2 of 2 Emissionsinfrequencybands(above1GHz)