2BG6L-B7SMART WATCH

INSTRUCTION MANUAL SMART WATCH Please read this manual carefully before using this product Open the package and take out the watch. Wear the smartwatch and long press the square button to open it. Watch Client Download and Connect Open the device on APP by scanning the QR code with your phone. Scan the OR code above to download the client 1. Download APP The app can be downloaded and installed on your mobile phone in several ways. You can either scan the OR code in the user manual, scan the built-in OR code of the watch. 2. Connect the Watch 1) Scan Code Connection: After Bluetooth is enabled on the mobile phone enter the APP (Note: If the APP cannot be opened, please open the positioning and then open the APP) and click Device -> Add Device -> click Scan code binding (scan the OR code on the watch]. 2) Manual Connection: After Bluetooth is enabled on the mobile phone enter the APP (Note: If the APP cannot be opened, Click Device -> Add Device -> Click Search Device (Find the device with the corresponding Bluetooth name and MAC address in "Settings"-> "System" -> "System Information" in the sliding control center of the watch) -> click Connect 3) Connect Bluetooth for Calls: When the watch is in the initial state. Bluetooth for calls is enabled by default. 1. Mobile Android System: After the watch is successfully connected to the APP, the mobile terminal will prompt the bracelet to request Bluetooth pairing - click pairing -Talk Bluetooth connection success, you can dial and talk after the connection is successful. 2. Mobile iOS System: After the watch is successfully connected to the APP the Bluetooth will automatically connect to the mobile phone. Once the connection is successful, you can dial and start talking. (Note: In the initial state of the watch the media audio is turned off by default. Media Audio Opening Method: Slide down the main interface of the watch face (Control Center) Click the phone icon there are two options (call audio/media audio Click the media audio the watch can play mobile music after opening. Charging and Activation Align the magnetic charger and the magnetic suction hole on the back of the watch to see the charging prompt on the screen of the watch. When the watch prompts low power, please charge it in time. The device is an all-in-one machine, the back shell and battery cannot be removed. Watch Operation Instructions 1. Dial Page -Long press the screen to enter the dial selection page -Left or right stroke can switch the dial. -Confirm the dial after clicking. Note: The system presets 6 dial pages, and the last dial is "Custom". This dial will change according to the dial market of the APP side and the download Settings of the custom dial 2. Menu Page -Press the right button on the dial page to enter the Menu page. -After entering the Menu page, press the right button twice continuously to switch the menu style, and press only once to return to the main Dial page. 3. Function Page Click the application icon on the Menu page to enter the corresponding function, Swipe right to return, and simply press the right button to return to the Main Dial page. Buttons and Touch Controls 1. In the shutdown state, long press the Square button to turn on the machine. In the startup state, long press the Square button to turn off the machine 2. Press the Square key on the main dial to access the Menu screen. 3. On the Menu screen, click the Square button to return to the Main Dial screen. 4. Double-click the Square button to switch to different menu styles. Watch Function Introduction Alarm After the watch is connected to the APP, you can set a single alarm clock, a cycle alarm clock, and up to 10alarm clocks in the APP terminal. Stopwatch - Click the Start button to start the timing. - Click the Pause button to stop the timing -Click the Reset button to return the timing to zero. Breathing Training -During breathing exercises, there are 1-minute and5- minute options. -Users click on the corresponding time to perform breathing training. -Click Start and follow the ICONS in the breathing exercises to zoom in and zoom out. Blood Pressure When entering the Blood Pressure Measurement Interface, the green light at the bottom will start the test and there will be a vibration reminder when the measurement is completed within 30 to 60 seconds. The measurement is based on PPG technology. Female After the watch is connected to the APP, a women's health alert can be enabled on the APP to view women's health information on the watch. Heart Rate When you enter the Heart Rate Measurement Interface, the green light at the bottom will start to measure. When the measurement is completed in about 40 seconds, there will be a vibration reminder. If the message "Please wear the watch correctly" is displayed, you need to wear the watch again. Blood oxygen When entering the interface of Blood Oxygen Measurement, the red light at the bottom will start the test for 30~60 second sand there will be a vibration reminder when the measurement is completed. The measurement is based on PPG technology Movement Sports mode options: Hiking, Running, Cycling, Mountaineering, Badminton, Baseball, Basketball, etc. Click the icon to start Sports. Weather When the watch is connected to the APP the weather interface will display real-time weather temperature and weather type. Messages After the watch is connected to the APP you can open the push of relevant information on the APP terminal. The watch terminal can receive the corresponding push message and save up to 15 latest messages. For example, after receiving a WeChat message, enter the WeChat function interface to view the message. After receiving a short message, enter the Information Interface to view the message. Set-Up The Settings function includes screen display (Switching Dial, On-Screen Duration, Brightness Adjustment, Wrister On-Screen Duration, and Touchscreen Clock), language, vibration intensity, menu style, battery, password, two-dimensional cod…

Text truncated - open the document above for the full version.

Shenzhen Hugh ANG Electronic Co.,Limited Room 609, C Building, Huafeng Robot Industrial Park, Bao'an District, Shen Zhen,China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-8-2 To whom it may concern: We, Shenzhen Hugh ANG Electronic Co.,Limited, hereby certify that the equipment for which authorization is sought (FCC ID: 2BG6L-B7) is not “covered” equipment prohibited from receiving an equipment authorization pursuant to § 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing “covered” equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, {新申请人签名} Signature steven Lai N/A Shenzhen Hugh ANG Electronic Co.,Limited 62_[model] CoveredEqu_2.911(d)(5)(i) and (ii) - U, V03

Shenzhen Hugh ANG Electronic Co.,Limited Room 609, C Building, Huafeng Robot Industrial Park, Bao'an District, Shen Zhen,China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-8-2 U.S. Agent Designation Shenzhen Hugh ANG Electronic Co.,Limited acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BG6L-B7): Name and company of U.S. agent: ACT Lab LLC Physical U.S. address of agent: 3280 East 59th Street Long Beach, CA 90805 United States FRN of U.S. agent: 0033465568 Email address of U.S. agent: [email protected] ACT Lab LLC acknowledges their obligation to accept service of process on behalf of Shenzhen Hugh ANG Electronic Co.,Limited. Shenzhen Hugh ANG Electronic Co.,Limited with the FRN [0035586833] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, {新申请人签名} Signature steven Lai N/A Shenzhen Hugh ANG Electronic Co.,Limited {代理商签名} Signature Scott Huber Senior Technical Director ACT Lab LLC 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2024-8-2> Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2BG6L-B7 B7 For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, {新申请人签名} Name/Title： steven Lai/N/A Company: Shenzhen Hugh ANG Electronic Co.,Limited Address: Room 609, C Building, Huafeng Robot Industrial Park, Bao'an District, Shen Zhen,China Phone: +86 13760447068 Fax: N/A E-Mail: [email protected]

Shenzhen Hugh ANG Electronic Co.,Limited Room 609, C Building, Huafeng Robot Industrial Park, Bao'an District, Shen Zhen,China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-8-2 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2BG6L-B7 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins’ current valid General Terms and Conditions (AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, {新申请人签名} Name/Title： steven Lai/N/A Company: Shenzhen Hugh ANG Electronic Co.,Limited Address: Room 609, C Building, Huafeng Robot Industrial Park, Bao'an District, Shen Zhen,China Phone: +86 13760447068 Fax: N/A E-Mail: [email protected]

FCC ID: 2BG6L-B7 TB-RF-074-1.0 Appendix III EUT External Photographs Photo 1 Appearance of EUT Photo 2 Appearance of EUT FCC ID: 2BG6L-B7 TB-RF-074-1.0 Photo 3 Appearance of EUT Photo 4 Appearance of EUT FCC ID: 2BG6L-B7 TB-RF-074-1.0 Photo 5 Appearance of EUT Photo 6 Appearance of EUT FCC ID: 2BG6L-B7 TB-RF-074-1.0 Photo 7Appearance of EUT

FCC ID: 2BG6L-B7 TB-RF-074-1.0 Appendix I Label Appendix II Label Location FCC ID:2BG6L-B7 Model: B7

FCC ID: 2BG6L-B7 TB-RF-074-1.0 Appendix IV EUT Internal Photographs Photo 8 Internal of EUT Photo 9 Appearance of PCB BT Antenna FCC ID: 2BG6L-B7 TB-RF-074-1.0 Photo 10 Appearance of PCB Photo 11 Battery Appearance

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202405-0278-4 Page: 1 of 3 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 Maximum Permissible Exposure Evaluation FCC ID: 2BG6L-B7 1. General Information about EUT 1.1 Client Information Applicant : Shenzhen Hugh ANG Electronic Co.,Limited Address : Room 609, C Building, Huafeng Robot Industrial Park, Bao'an District, Shen Zhen,China Manufacturer : Shenzhen Chai Gao Electronic technology Co., Ltd Address : Room 609, C Building, Huafeng Robot Industrial Park, Bao'an District, Shen Zhen,China 1.2 General Description of EUT (Equipment Under Test) EUT Name : SMART WATCH Models No. : B7 Model Different : N/A Brand Name : N/A Sample ID : HC-C-202405-0278-01-01 Product Description : Operation Frequency: Bluetooth&BLE: 2402MHz~2480MHz Antenna Gain: 0dBi Conducting Wire Antenna Power Rating : USB Input: DC 5 V DC 3.8V 300mAh Rechargeable Li-ion battery Software Version : N/A Hardware Version : N/A Remark: The above antenna information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications, the laboratory shall not be held responsible. Report No.: TBR-C-202405-0278-4 Page: 2 of 3 TB-RF-074-1.0 SAR Test Exclusion Calculations 1. FCC: According to KDB 447498 D01 Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies v06. (1) Clause 4.3: General SAR test reduction and exclusion guidance Sub clause 4.31: Standalone SAR test exclusion considerations 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6GHz at test separation distance≤5 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√ f (GHz) ] ≤3.0 for 1-g SAR [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√ f (GHz) ] ≤7.5.0 for 10-g SAR 2. Summary simultaneous transmission for SAR Exclusion The SAR exemption limits outlined in clause 4.3.2(b) of KDB 447498 have been derived based on an approximate SAR value of 0.4 W/kg using half-wave dipole antennas Footnote 1. As such, when simultaneous transmitter SAR evaluations include transmitters that have been exempt from routine SAR evaluation, the SAR must be estimating based on the ratio between the maximum tune-up tolerance limit of the transmitter that has been exempt and the exemption limit at the specific distance and frequency for that transmitter. This ratio must be multiplied by 0.4 W/kg (2.0 W/kg for controlled use and 1.0 W/kg for limb worn devices) in order to calculate the estimated SAR level. The estimate SAR value is calculated based the following equation: (maximum power level including tune-up tolerance for transmitter A / maximum power level of exemption at the same frequency and distance) * 0.4W/kg The [∑ of (the highest measured or estimated SAR for each standalone antenna configuration, adjusted for maximum tune-up tolerance) / 1.6 W/kg] + [∑ of MPE ratios] is ≤ 1.0. The SAR to peak location separation ratios of all simultaneously transmitting antenna pairs operating in portable device exposure conditions are all ≤ 0.04, and the [∑ of MPE ratios] is ≤ 1.0. Report No.: TBR-C-202405-0278-4 Page: 3 of 3 TB-RF-074-1.0 3. Calculation: Test separation: 5mm Bluetooth Mode (GFSK) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2402 -1.489 -1±1 0 1.000 0.310 3.0 2441 -1.085 -1±1 0 1.000 0.312 3.0 2480 -1.140 -1±1 0 1.000 0.315 3.0 Bluetooth Mode (π/4-DQPSK) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2402 -0.653 0±1 1 1.259 0.390 3.0 2441 -0.286 0±1 1 1.259 0.393 3.0 2480 -0.399 0±1 1 1.259 0.397 3.0 Bluetooth Mode (8-DPSK) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2402 -0.021 0±1 1 1.259 0.390 3.0 2441 0.325 0±1 1 1.259 0.393 3.0 2480 0.247 0±1 1 1.259 0.397 3.0 BLE 1M Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2402 7.098 7±1 8 6.310 1.956 3.0 2440 7.214 7±1 8 6.310 1.972 3.0 2480 7.080 7±1 8 6.310 1.987 3.0 BLE 2M Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2402 7.124 7±1 8 6.310 1.956 3.0 2440 7.347 7±1 8 6.310 1.972 3.0 2480 7.232 7±1 8 6.310 1.987 3.0 Conclusion: The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06. -----END OF REPORT-----

Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202405-0278-9 Page: 1 of 39 FCC ID: 2BG6L-B7 TB-RF-074-1.0 RF Test Data for Bluetooth LE (Conducted Measurements) General Description of EUT Product Name: SMART WATCH Test Model: B7 Sample ID: HC-C-202405-0278-01-02 Environmental Conditions Temperature: 24.2°C Relative Humidity: 54% Test Voltage: DC 3.8V Test Engineer: Mike YAN Note: For a more detailed features description, please refer to the report TBR-C-202405-0278-9 The report only show the worst case data. Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202405-0278-9 Page: 2 of 39 FCC ID: 2BG6L-B7 TB-RF-074-1.0 Contents 1. Duty Cycle ........................................................................................................................................................................................... 3 2. Maximum Conducted Output Power ................................................................................................................................................. 7 3. -6dB Bandwidth ................................................................................................................................................................................ 11 4. Occupied Channel Bandwidth ......................................................................................................................................................... 15 5. Maximum Power Spectral Density Level ......................................................................................................................................... 19 6. Band Edge ........................................................................................................................................................................................ 23 7. Conducted RF Spurious Emission .................................................................................................................................................. 28 8. Restrict Band .................................................................................................................................................................................... 35 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202405-0278-9 Page: 3 of 39 FCC ID: 2BG6L-B7 TB-RF-074-1.0 1. Duty Cycle Condition Mode Frequency (MHz) Antenna Duty Cycle (%) Correction Factor (dB) 1/T (kHz) NVNT BLE 1Mbps 2402 Ant1 87.2 0.59 0.46 NVNT BLE 1Mbps 2440 Ant1 87.2 0.59 0.46 NVNT BLE 1Mbps 2480 Ant1 87.6 0.57 0.46 NVNT BLE 2Mbps 2402 Ant1 45.2 3.45 0.88 NVNT BLE 2Mbps 2440 Ant1 45.2 3.45 0.88 NVNT BLE 2Mbps 2480 Ant1 45.2 3.45 0.88 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202405-0278-9 Page: 4 of 39 FCC ID: 2BG6L-B7 TB-RF-074-1.0 Test Graphs Duty Cycle NVNT BLE 1Mbps 2402MHz Ant1 Duty Cycle NVNT BLE 1Mbps 2440MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202405-0278-9 Page: 5 of 39 FCC ID: 2BG6L-B7 TB-RF-074-1.0 Duty Cycle NVNT BLE 1Mbps 2480MHz Ant1 Duty Cycle NVNT BLE 2Mbps 2402MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202405-0278-9 Page: 6 of 39 FCC ID: 2BG6L-B7 TB-RF-074-1.0 Duty Cycle NVNT BLE 2Mbps 2440MHz Ant1 Duty Cycle NVNT BLE 2Mbps 2480MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202405-0278-9 Page: 7 of 39 FCC ID: 2BG6L-B7 TB-RF-074-1.0 2. Maximum Conducted Output Power Condition Mode Frequency (MHz) Antenna Total Power (dBm) Limit (dBm) Verdict NVNT BLE 1Mbps 2402 Ant1 7.098 30 Pass NVNT BLE 1Mbps 2440 Ant1 7.214 30 Pass NVNT BLE 1Mbps 2480 Ant1 7.08 30 Pass NVNT BLE 2Mbps 2402 Ant1 7.124 30 Pass NVNT BLE 2Mbps 2440 Ant1 7.347 30 Pass NVNT BLE 2Mbps 2480 Ant1 7.232 30 Pass Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202405-0278-9 Page: 8 of 39 FCC ID: 2BG6L-B7 TB-RF-074-1.0 Test Graphs Power NVNT BLE 1Mbps 2402MHz Ant1 Power NVNT BLE 1Mbps 2440MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202405-0278-9 Page: 9 of 39 FCC ID: 2BG6L-B7 TB-RF-074-1.0 Power NVNT BLE 1Mbps 2480MHz Ant1 Power NVNT BLE 2Mbps 2402MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202405-0278-9 Page: 10 of 39 FCC ID: 2BG6L-B7 TB-RF-074-1.0 Power NVNT BLE 2Mbps 2440MHz Ant1 Power NVNT BLE 2Mbps 2480MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202405-0278-9 Page: 11 of 39 FCC ID: 2BG6L-B7 TB-RF-074-1.0 3. -6dB Bandwidth Condition Mode Frequency (MHz) Antenna -6 dB Bandwidth (MHz) Limit -6 dB Bandwidth (MHz) Verdict NVNT BLE 1Mbps 2402 Ant1 0.65 0.5 Pass NVNT BLE 1Mbps…

Text truncated - open the document above for the full version.

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202405-0278-9 Page: 1 of 34 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 Radio Test Report FCC ID: 2BG6L-B7 Report No. : TBR-C-202405-0278-9 Applicant : Shenzhen Hugh ANG Electronic Co.,Limited Equipment Under Test (EUT) EUT Name : SMART WATCH Model No. : B7 Series Model No. : N/A Brand Name : N/A Sample ID : HC-C-202405-0278-01-01&HC-C-202405-0278-01-02 Receipt Date : 2024-06-06 Test Date : 2024-06-06 to 2024-06-24 Issue Date : 2024-06-24 Standards : FCC Part 15 Subpart C 15.247 Test Method : ANSI C63.10: 2013 KDB 558074 D01 15.247 Meas Guidance v05r02 Conclusions : PASS In the configuration tested, the EUT complied with the standards specified above. Test By : Mike Yan Reviewed By : Henry Huang Approved By : Ivan Su This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in the report. Report No.: TBR-C-202405-0278-9 Page: 2 of 34 TB-RF-074-1.0 Contents CONTENTS ............................................................................................................................................ 2 1. GENERAL INFORMATION ABOUT EUT ............................................................................. 5 1.1 Client Information ................................................................................................................ 5 1.2 General Description of EUT (Equipment Under Test) ................................................... 5 1.3 Block Diagram Showing the Configuration of System Tested ...................................... 6 1.4 Description of Support Units .............................................................................................. 7 1.5 Description of Test Mode ................................................................................................... 7 1.6 Description of Test Software Setting ................................................................................ 8 1.7 Measurement Uncertainty .................................................................................................. 8 1.8 Test Facility........................................................................................................................... 9 2. TEST SUMMARY..................................................................................................................... 10 3. TEST SOFTWARE .................................................................................................................. 10 4. TEST EQUIPMENT AND TEST SITE .................................................................................. 11 5. CONDUCTED EMISSION ...................................................................................................... 12 5.1 Test Standard and Limit ................................................................................................... 12 5.2 Test Setup........................................................................................................................... 12 5.3 Test Procedure .................................................................................................................. 12 5.4 Deviation From Test Standard......................................................................................... 13 5.5 EUT Operating Mode ........................................................................................................ 13 5.6 Test Data............................................................................................................................. 13 6. RADIATED AND CONDUCTED UNWANTED EMISSIONS ............................................ 14 6.1 Test Standard and Limit ................................................................................................... 14 6.2 Test Setup........................................................................................................................... 15 6.3 Test Procedure .................................................................................................................. 16 6.4 Deviation From Test Standard......................................................................................... 17 6.5 EUT Operating Mode ........................................................................................................ 17 6.6 Test Data............................................................................................................................. 17 7. RESTRICTED BANDS AND BAND EDGE REQUIREMENT .......................................... 18 7.1 Test Standard and Limit ................................................................................................... 18 7.2 Test Setup........................................................................................................................... 18 7.3 Test Procedure .................................................................................................................. 19 7.4 Deviation From Test Standard......................................................................................... 19 7.5 EUT Operating Mode ........................................................................................................ 19 7.6 Test Data............................................................................................................................. 19 8. BANDWIDTH TEST................................................................................................................. 20 8.1 Test Standard and Limit ................................................................................................... 20 8.2 Test Setup......................................................…

Text truncated - open the document above for the full version.

FCC ID: 2BG6L-B7 TB-RF-074-1.0 Appendix V EUT Test Photographs Photo of Setup for Conducted Emission(AC POWER) Photo of Setup for Radiated Emission (30MHz~1GHz) FCC ID: 2BG6L-B7 TB-RF-074-1.0 Photo of Setup for Radiated Emission (Above 1 GHz) -----END OF REPORT-----