2BG9R-H010Bluetooth Low Energy module H9518Fx

H-zLink (Nanjing) Electronics Co., Ltd. __________________________________________ H9518Fx Datesheet Bluetooth Low Energy Module Rev2.0 2024.02 H9518Fx Datasheet | v2.0 2 / 14 ORDERING INFORMATION Order code ANT Power Supply TX Power Feature H9518Fx PCB 1.8～4.3V 2.30～3.47dBm Master-Slave Integration Transparent Transmission NAMING CONVENTIONS H9518Fx Datasheet | v2.0 3 / 14 CONTENTS ORDERING INFORMATION ........................................................................................................ 2 NAMING CONVENTIONS ............................................................................................................ 2 1. DESCRIPTION ............................................................................................................................ 4 2. FEATURES .................................................................................................................................. 4 3. TYPICAL APPLICATIONS ........................................................................................................ 5 4. BASE SPECIFICATION ............................................................................................................. 6 5. PACKAGE ................................................................................................................................... 7 6. PINS DESCRIPTION .................................................................................................................. 7 7. APPLICATION CIRCUIT ........................................................................................................... 9 8. PACKAGE PHYSICAL DIMENSIONS ..................................................................................... 9 9. GRNWE-PICTURE ................................................................................................................... 10 10. PACKING INFORMATION .................................................................................................... 10 11. REVISION HISTORY ............................................................................................................. 10 IMPORTANT NOTICE ................................................................................................................. 11 H9518Fx Datasheet | v2.0 4 / 14 1. DESCRIPTION The H9518Fx is a Bluetooth Low Energy module that contains Bluetooth V5.3 (LE Mode) fully compliant system with H-zLink designed firmware and software stack. This product is a Bluetooth standard compliant module based on a universal serial interface, capable of facilitating data transfer between the user's serial port and Bluetooth interface. It also offers a rich array of pins (UART, I2C, SPI, GPIO, ADC, PWM, Audio, etc.), providing flexible and comprehensive software and hardware customization services. This supports seamless client application development, bypassing the complex RF hardware design and manufacturing process. With a complete data transmission software platform, it meets the requirements for rapid development, reduces software investment, and shortens the R&D cycle. The product features low power consumption, compact size, high cost-effectiveness, strong platform compatibility, high performance, and robust interference resistance. 2. FEATURES ⚫ The ARM Cortex-M3 core MCU operates at 48MHz. ⚫ Based on the Bluetooth Low Energy 5.3 standard protocol stack and additionally supports application layer protocols such as HID. ⚫ It has On-board PCB ANT. Transmission distance can reach 40~100m in open environments, also it supports a reserved external RF interface and can transmit over longer distances. ⚫ The power supply range is wide, from 1.8V to 4.3V, with a typical value of 3.3V. It supports direct power supply from button or lithium batteries for operation in low-power modes. ⚫ It supports a single analog MIC interface and has an in-built Audio voice decoder with a dedicated high-precision ADC for high-fidelity audio effects. ⚫ In low-power mode with RTC wake-up, the power consumption can be as low as 6.1μA, and in power-down sleep mode, the power consumption can reach as low as 2.7μA. ⚫ It allows for custom transmission power and parameters for connection and broadcasting intervals, supporting up to 10dBm transmission power. ⚫ It supports dual-mode operation, allowing for configuration as either a master or a slave device, and it can support up to 2 masters and 18 slaves working simultaneously. ⚫ The module supports OTA (Over-The-Air) firmware upgrades, with air data transmission rates supporting different levels of 2M/1M/500K/125K. ⚫ Operation temperature: -40°C to +85°C. LxWxH: 16x11.2x1.8mm. H9518Fx Datasheet | v2.0 5 / 14 3. TYPICAL APPLICATIONS H9518Fx can be widely used in the following application scenarios ⚫ 2.4GHz Bluetooth Low Energy systems； ⚫ IoT devices with support for local voice announcements； ⚫ Low-power peripheral devices for PCs, tablets, and smartphones (such as HID devices, remote controllers, etc.) ； ⚫ Smart sports, medical healthcare, and other consumer electronic products； ⚫ Smart meters, data acquisition, and other wireless sensor networks. H9518Fx Datasheet | v2.0 6 / 14 4. BASE SPECIFICATION Sheet 1 Specification Content Specification Core Specification V5.3 (LE Mode) Supply Voltage 1.8~4.3V（Typ 3.3V） Frequency range 2.400~2.4835GHz TDP Tx peek current 8mA@0dB Rx peek current 9.7mA Deep sleep current (include 48K retention RAM) 6.1uA Power off 2.7uA Tx Power -16~+10 dBm Operating Temp -40~+85°C Storage Temp -40~+125°C Channel 40（3 ADV+37 DATA） Modulation GFSK（Supports adaptive frequency hopping） IO control voltage 0~VCC Airborne baud rate 2M/1M（Unit：bps） Connected Mode 2 master 18 slave connection Distance 40～100m（On-board ANT in open environments） Interface 1.27 Spacing stamp holes（SMD） SW Update OTA ESD ±2kV（HBM/CDM） SIZE 16*11.2*1.8mm PS：The aforementioned electrical parameters are all tested in an environment of 25°C ± 3°C. 【Distance】Subject to influence from the surrounding envir…

Text truncated - open the document above for the full version.

H-zLink(Nanjing)ElectronicsCo., Ltd. U.S. Agent Designationfor Serviceof Process (Applicant and U.S.Agentare SeparateParties) TO:FederalCommunications Commission 7435OaklandMillsRoad Columbia,MD 21046 ATTENTION:FCC Certification– Section2.911(d)(7) Information DesignatedU.S. Agent CompanyName:United ConsultingTechnologyServicesCo., Ltd. FRN:0033495714 Contact Name: DavidWu StreetAddress: 17800CASTLETONST STE665 CITYOF INDUSTRY City/Province/Zip:CA91748 Telephone No: (626) 217-4022 Email:[email protected] This letter is toconfirmthat we (“the DesignatedU.S. Agent)haveacceptedthe responsibility toact as the DesignatedU.S. Agent forServiceof Processas requiredbysection47 CFR2.911(d)(7)on behalfof the Applicantnotedbelow. U .S. AgentSignature: Date:2024-08-22 Signed by(Printed Name/Title):DavidWu/ CEO The Applicant acknowledgesthat theymustmaintainan agentfor noless than one year after terminating all marketing andimportationOR the conclusionofany Commission-relatedproceedinginvolving the equipment.The applicantfurtheracknowledgestheir responsibility toinformthe FCCwheneverthe DesignatedU.S. Agentinformationabove changes. A pplicant Companyname:H-zLink(Nanjing)ElectronicsCo., Ltd. Grantee Code:2BG9R FCCID: 2BG9R-H010 Contact Name:Lili Liu StreetAddress: Room 2106, BuildingD2, Duhui TiandiCity,No.28 JiangnanRoad,Nanjing, China City/Province/Zip:Nanjing,China Telephone No: +86-13770786108 Email:[email protected] Applicant Signature: Date:2024-08-22 Signed by(Printed Name/Title):Feng Xu,Manager

Applicant Declaration QSF27-14-04 Rev 1.0 Rev. Feb 6, 2023 Page 1 of 1 Original Issue: Jan. 4, 2021 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name H-zLink (Nanjing) Electronics Co., Ltd. Address Room 2106, BuildingD2, Duhui Tiandi City, No.28 Jiangnan Road, Nanjing, China Grantee Code 2BG9R FCC ID 2BG9R-H010 Authorized Contact Name Lili Liu Contact Email [email protected] Contact Phone +86-13770786108 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List H-zLink (Nanjing) Electronics Co., Ltd. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. H-zLink (Nanjing) Electronics Co., Ltd. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [ is not] identified on the Covered list, established pursuant to §1.50002, as an entity producing “covered” equipment. Applicant Signature: Date:2024/8/22 Print Name: Lili Liu Title: Legal Representative *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

H-zLink (Nanjing) Electronics Co., Ltd. Date: 2024/8/22 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID:2BG9R-H010 To whom it may concern: We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with H-zLink (Nanjing) Electronics Co., Ltd. . . This authorization is valid until further written notice from the applicant. Name (Printed): Lili Liu Title: Legal Representative Signature: On behalf of Company: H-zLink (Nanjing) Electronics Co., Ltd. Telephone: +86-13770786108

H-zLink (Nanjing) Electronics Co., Ltd. To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: H-zLink (Nanjing) Electronics Co., Ltd. Room 2106, BuildingD2, Duhui Tiandi City, No.28 Jiangnan Road, Nanjing, China Regarding: Confidentiality Request regarding application for FCC ID: 2BG9R-H010 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature: Printed Name (on file with the FCC associated with the Grantee Code): Lili Liu Title: Legal Representative Company Name: H-zLink (Nanjing) Electronics Co., Ltd.

H-zLink (Nanjing) Electronics Co., Ltd. Cover Letter-Modular Approval FCC ID: 2A3WYIDC777 Date: 2024-08-22 Gentlemen: There’s a radar Module that would like to have your authorization as a modular approval. The specific product as below, radar Module with its designed features and specified description, meets special requirements for Full modular approval on FCC KDB996369 by cross-reference list below. Company H-zLink (Nanjing) Electronics Co., Ltd. Model Name Bluetooth Low Energy module H9518Fx Model Number H9518Fx FCC ID 2BG9R-H010 Requirement of FCC KDB996369 Comply（Y/N） 1. The modular transmitter must have its own RF shielding. Y The EUT has its own RF shielding. Please refer to EUT Photos. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. Y The EUT uses the chip: H8105A as an embedded processor to buffer the data. Please refer to Schematics. 3. The modular transmitter must have its own power supply regulation. Y The EUT has its own power supply regulation, The power supply of this module is 3.3V. Please refer to Schematics. 4. The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. Y The EUT meets the FCC antenna requirements; The photo of antenna is shown in the test report. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. Y The EUT was tested with a test cable, see test report and setup photo 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2BG9R-H010” or “Contains FCC ID: 2BG9R-H010” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module Y Please see exhibition label sample for the FCC ID of this module. And also in the exhibition User’s manual, there are instructions to the OEM on how to label the end product. H-zLink (Nanjing) Electronics Co., Ltd. which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. Y The EUT is compliant with all applicable FCC rules. Details instructions for maintaining compliance are given in the User Manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Y The EUT complies with RF exposure requirement. Thank you. Sincerely, Print Name: Lili Liu Title: Director Signature: On behalf of Company: H-zLink (Nanjing) Electronics Co., Ltd. Telephone: +86-13770786108

Compliance Certification Services (Kunshan) Inc. Page: 1 of 2 External Photos for KSCR2406001151AT Test Model No.: H9518Fx Compliance Certification Services (Kunshan) Inc. Page: 2 of 2 EUT Constructional Details (EUT Photos)

PAC102 PAC101 COC1 PAC202 PAC201 COC2 PAC302 PAC301 COC3 PAC401 PAC402 COC4 PAC502 PAC501 COC5 PAC601 PAC602 COC6 PAC701 PAC702 COC7 PAJP108 PAJP107 PAJP106 PAJP104 PAJP103 PAJP102 PAJP101 PAJP105 PAJP109 COJP1 PAJP2016 PAJP2017 PAJP2018 PAJP2020 PAJP2021 PAJP2022 PAJP2023 PAJP2019 PAJP2015 COJP2 PAJP3012 PAJP3014 PAJP3013 PAJP3011 PAJP3010 COJP3 PAL102 PAL101 COL1 PAL202 PAL201 COL2 PAR102 PAR101 COR1 PAR201 PAR202 COR2 PAS10 COS1 PAU1024 PAU1023 PAU1022 PAU1021 PAU1020 PAU1019 PAU1018 PAU1017 PAU108 PAU107 PAU106 PAU105 PAU104 PAU103 PAU102 PAU101 PAU1033 PAU1032 PAU1031 PAU1030 PAU1029 PAU1028 PAU1027 PAU1026 PAU1025 PAU1016 PAU1015 PAU1014 PAU1013 PAU1012 PAU1011 PAU1010 PAU109 COU1 PAX102 PAX104 PAX103 PAX101 COX1 Remark:It’s hard to put FCC statement on the product due to device’s irregular appearance. FCC statement will be placed in the user manual which the device is marketed.

Compliance Certification Services (Kunshan) Inc. Page: 1 of 2 Internal Photos for KSCR2406001151AT Test Model No.: H9518Fx Compliance Certification Services (Kunshan) Inc. Page: 2 of 2 EUT Constructional Details (EUT Photos)

Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240600115102 Page: 1 of 10 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. Member of the SGS Group (SGS SA) 1 Cover Page RF Exposure Evaluation Report Application No.: KSCR2406001151AT FCC ID: 2BG9R-H010 Applicant: H-zLink (Nanjing) Electronics Co., Ltd. Address of Applicant: Room 2106, BuildingD2, Duhui Tiandi City, No.28 Jiangnan Road, Nanjing 210028,P.R.China Manufacturer: H-zLink (Nanjing) Electronics Co., Ltd. Address of Manufacturer: Room 2106, BuildingD2, Duhui Tiandi City, No.28 Jiangnan Road, Nanjing 210028,P.R.China Factory: Shenzhen JLC Technology Group Co., Ltd. Address of Factory: 27 Floor,Olympic Building,No.2 ShangBao Road,Futian District,Shenzhen Guangdong Province, China Equipment Under Test (EUT): EUT Name: Bluetooth Low Energy module H9518Fx Model No.: H9518Fx Trade Mark: H-zLink Standard(s) : FCC Rules 47 CFR §2.1091 KDB 447498 D04 interim General RF Exposure Guidance v01 Date of Receipt: 2024-06-21 Date of Test: 2024-07-26 to 2024-08-16 Date of Issue: 2024-08-19 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. SHEM-TRF-001 Rev. 02 Sep01, 2023 Report No.: KSCR240600115102 Page: 2 of 10 Revision Record Version Description Date Remark 00 Original 2024-08-19 / Authorized for issue by: Tested By Tommie Tang /Project Engineer Approved By Terry Hou /Reviewer SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. SHEM-TRF-001 Rev. 02 Sep01, 2023 Report No.: KSCR240600115102 Page: 3 of 10 2 Contents Page 1 Cover Page ........................................................................................................................................ 1 2 Contents ............................................................................................................................................ 3 3 General Information .......................................................................................................................... 4 3.1 General Description of E.U.T. .................................................................................................... 4 3.2 Technical Specifications ............................................................................................................. 4 3.3 Separation Distance ................................................................................................................... 4 3.4 Test Location .............................................................................................................................. 5 3.5 Test Facility ................................................................................................................................ 5 4 RF Exposure Test Exemptions ........................................................................................................ 6 4.1 RF Exposure Test Exemptions for single RF sources ............................................................... 6 4.2 RF Exposure Test Exemptions for Simultaneous Transmission ................................................ 8 5 Measurement and Calculation ....................................................................................................... 10 5.1 Maximum transmit power ......................................................................................................... 10 5.2 RF Exposure Calculation ......................................................................................................... 10 SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. SHEM-TRF-001 Rev. 02 Sep01, 2023 Report No.: KSCR240600115102 Page: 4 of 10 3 General Information 3.1 General Description of E.U.T. Power supply: DC 3.3V 3.2 Technical Specifications Operation Frequency: 2402MHz to 2480MHz Modulation Type: GFSK Number of Channels: 40 Channel Spacing: 2MHz Antenna Type: PCB Antenna Antenna Gain: 0dBi (Provided by the manufacturer) 3.3 Separation Distance Separation distance between the antenna to person (R): ＞20cm Remark: This minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. R has been stated in user manual. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. SHEM-TRF-001 Rev. 02 Sep01, 2023 Report No.: KSCR240600115102 Page: 5 of 10 3.4 Test Location All tests were performed at: Compliance Certification Services (Kunshan) Inc. No.10 Weiye Rd, Innovation park, Eco&Tec, Development Zone, Kunshan City, Jiangsu, China.…

Text truncated - open the document above for the full version.

Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240600115101 Page: 1 of 78 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. Member of the SGS Group (SGS SA) TEST REPORT Application No.: KSCR2406001151AT FCC ID: 2BG9R-H010 Applicant: H-zLink (Nanjing) Electronics Co., Ltd. Address of Applicant: Room 2106, BuildingD2, Duhui Tiandi City, No.28 Jiangnan Road, Nanjing 210028,P.R.China Manufacturer: H-zLink (Nanjing) Electronics Co., Ltd. Address of Manufacturer: Room 2106, BuildingD2, Duhui Tiandi City, No.28 Jiangnan Road, Nanjing 210028,P.R.China Factory: Shenzhen JLC Technology Group Co., Ltd. Address of Factory: 27 Floor,Olympic Building,No.2 ShangBao Road,Futian District,Shenzhen Guangdong Province, China Equipment Under Test (EUT): EUT Name: Bluetooth Low Energy module H9518Fx Model No.: H9518Fx Trade Mark: H-zLink Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2024-06-21 Date of Test: 2024-07-26 to 2024-08-16 Date of Issue: 2024-08-19 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240600115101 Page: 2 of 78 Revision Record Version Description Date Remark 00 Original 2024-08-19 / Authorized for issue by: Tested By Tommie Tang /Project Engineer Approved By Terry Hou /Reviewer Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240600115101 Page: 3 of 78 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Emissions at AC Power Line (150kHz-30MHz) 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.2 47 CFR Part 15, Subpart C 15.207 Pass Radiated Emissions which fall in the restricted bands ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Below 1GHz ANSI C63.10 (2013) Section 6.4,6.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Above 1GHz ANSI C63.10 (2013) Section 6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Conducted Peak Output Power ANSI C63.10 (2013) Section 11.9.1 47 CFR Part 15, Subpart C 15.247(b)(3) Pass Minimum 6dB Bandwidth ANSI C63.10 (2013) Section 11.8.1 47 CFR Part 15, Subpart C 15.247a(2) Pass Power Spectrum Density ANSI C63.10 (2013) Section 11.10.2 47 CFR Part 15, Subpart C 15.247(e) Pass Conducted Band Edges Measurement ANSI C63.10 (2013) Section 11.13.3.2 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions ANSI C63.10 (2013) Section 11.11 47 CFR Part 15, Subpart C 15.247(d) Pass Compliance Certification Services (Kunshan) Inc. CCSEM-TRF-001 Rev. 02 Sep 01, 2023 Report No.: KSCR240600115101 Page: 4 of 78 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 Test Summary .................................................................................................................................................. 3 3 Contents ........................................................................................................................................................... 4 4 General Inf…

Text truncated - open the document above for the full version.