2BGJ4-DLB523ACDISHWireless Bridge

Quick Setup Guide Long Range
Wireless Bridge Models: DLB 5-23ac DISH Quick Setup Guide Long Range Wireless Bridge Models: WIS-D523 / WIS-D523AC Feedhorn Package content Interface LED Interface 1 2 Dish Feed ReceiverBall Joint Mount Metal Strap 24V PoE AdapterQuick Setup Guide LED Description PWR WLAN ETH No. Description On: the radio is powered up On: the wireless is available Flashing: wireless data transfering On: the wire connection is available Flashing: wire data transfering Signal strength 0 LED: -95dBm~-90dBm 1 LED: -90dBm~-80dBm 2 LED: -80dBm~-65dBm 3 LED: more than -65dBm Ethernet port Reset button Press more than 8s to restore factory settings 3 Install the radio Install the radio to a pole 1. Combine the two parts of the dish reflector.2. Hold the reflector assembly by hand (do not use a tabletop or flat surface) and insert the Feed Re- ceiver into the reflector, secure it with two screw. WARNING Do not install the Feed Receiver into the reflector assembly by pushing down onto a tabletop or other flat surface as this can deform the panels. Hold the reflector assembly by hand. 3. Insert the Radio Feed into the Feed Re- ceiver. 4. Attach the Ball Joint Mount to the Feed Re- ceiver by turning the lock nut clockwise by hand. Do not tighten the nut. 5. Pull out the port cover and connect an Ethernet cable to the port, then push back the cover. 6. Open the Metal Strap and feed it through the two slots ofthe Ball Joint Mount, then wrap the Metal Strap around the pole. 7. Loosen the lock nut on the Ball Joint Mount, and aim at the other end of the wireless link. After that lock the nut. Power up the radio To the radio To computer or to network Connect one end of an Ethernet cable to the POE port of the provided PoE DC Adapter and the other end of the Ethernet cable to the RJ45 port of the device. Then, connect the LAN port of the PoE DC Adapter to a PC or switch using another Ethernet cable. Finally, plug the PoE DC Adapter into a standard electrical wall socket. ATTENTION If you use other PoE Adapter which is not provided by , we can’t provide warranty service if device damage caused. 4 Web configuration 1. Check all wires are correctly connected. 2. Configure the host system with static IP on the 192.168.1.x (x could be 10~254) subnet. 3. Using a web browser access 192.168.1.2 (wait a few seconds after device power up). 4. When login page appears enter “admin” in both the username and password fields. Installer Compliance Responsibility Devices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements. The setting is at WiFi page, Region Code. Since equipment can be set with various radio frequency parameters, such as the radio output power, channels are set with different values due to the region code selection. The installer should use the radio meeting regulatory requirements. Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. 3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet. a. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire. b. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death. c. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment. d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection. e. Protective bonding must be installed in accordance with local national wiring rules and regulations. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. Alert sign must be indicated if a restriction on use applied to the product and it must follow the CE marking. RoHS/WEEE Compliance Statement European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or…

Text truncated - open the document above for the full version.

Shenzhen EZL Technology Co.,Ltd 301-D24, Xiangjiang Financial Building, No.3046 Xinghai Avenue, Nanshan, Qianhai Shenzhen China 518000 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD21046 2024-6-17 To whom it may concern: We, Shenzhen EZL Technology Co.,Ltd , hereby certify that the equipment for which authorization is sought (FCC ID:2BGJ4-DLB523ACDISH)is not “covered” equipment prohibited from receiving an equipment authorization pursuant to § 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List ( https://www.fcc.gov/supplychain/coveredlist) as an entity producing “covered” equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, Signature JimGao CEO Shenzhen EZL Technology Co.,Ltd 62_[model] CoveredEqu_2.911(d)(5)(i) and (ii) - U, V03

Shenzhen EZL Technology Co.,Ltd 301-D24, Xiangjiang Financial Building, No.3046 Xinghai Avenue, Nanshan, Qianhai Shenzhen China 518000 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD21046 2024-6-17 U.S. Agent Designation Shenzhen EZL Technology Co.,Ltd acknowledges their consent for the following contact located in the United States to act as their agent for service of processfor the equipment for which authorization is sought (FCC ID: 2BGJ4-DLB523ACDISH): Name and company of U.S. agent: ACT Lab LLC Physical U.S. address of agent: 3280 East 59th Street Long Beach, CA 90805 United States FRN of U.S. agent: 0033465568 Email address of U.S. agent: [email protected] ACT Lab LLCacknowledges their obligation to accept service of process on behalf of Shenzhen EZL Technology Co.,Ltd . Shenzhen EZL Technology Co.,Ltd with the FRN [0035455997] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature JimGao CEO Shenzhen EZL Technology Co.,Ltd Signature Scott Huber Senior Technical Director ACT Lab LLC 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2024-6-17> Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2BGJ4-DLB523ACDISH DLB 5-23ac DISH For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title： JimGao/CEO Company: Shenzhen EZL Technology Co.,Ltd Address: 301-D24, Xiangjiang Financial Building, No.3046 Xinghai Avenue, Nanshan, Qianhai Shenzhen China 518000 Phone: +8619065068726 Fax: N/A E-Mail: [email protected]

Shenzhen EZL Technology Co.,Ltd 301-D24, Xiangjiang Financial Building, No.3046 Xinghai Avenue, Nanshan, Qianhai Shenzhen China 518000 UNII Device Declaration Letter To whom it may concern: We have declared below featured for FCC equipment authorization, Device FCC ID: 2BGJ4-DLB523ACDISH (1) DFS Device: Master Client with Radar detection capability N/A Client without radar detection capability, (2) Active / Passive Scanning, adhoc mode access point capability Frequency Band (MHz) Active Scanning (the device can transmit a probe (beacon)) passive scanning (where the device is can listen only with no probes) Ad Hoc Mode capability Access point capability 5180-5240 Yes No Yes No Yes No Yes No 5190-5230 Yes No Yes No Yes No Yes No 5210-5210 Yes No Yes No Yes No Yes No 5260-5320 Yes No Yes No Yes No Yes No 5270-5310 Yes No Yes No Yes No Yes No 5290-5290 Yes No Yes No Yes No Yes No 5500-5700 Yes No Yes No Yes No Yes No 5510-5670 Yes No Yes No Yes No Yes No 5530-5610 Yes No Yes No Yes No Yes No 5745-5825 Yes No Yes No Yes No Yes No 5755-5795 Yes No Yes No Yes No Yes No 5775-5775 Yes No Yes No Yes No Yes No (3) Country code selection ability Yes No If yes, pls explain how it was implemented: (4) Meet 15.202 requirement Yes No pls check below : A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network. (5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by end user or an installer. Apply Does not apply (If apply, pls help to provide explanation on it was implement, and how software was controlled) Should you have any questions or comments regarding this matter, please have my best attention. Sin cerely, (Signed) Name/Title： JimGao/CEO Company: Shenzhen EZL Technology Co.,Ltd Address: 301-D24, Xiangjiang Financial Building, No.3046 Xinghai Avenue, Nanshan, Qianhai Shenzhen China 518000 Phone: +8619065068726 Fax: N/A E-Mail:[email protected]

Shenzhen EZL Technology Co.,Ltd 301-D24, Xiangjiang Financial Building, No.3046 Xinghai Avenue, Nanshan, Qianhai Shenzhen China 518000 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD21046 2024-6-17 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2BGJ4-DLB523ACDISHincluding the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbHon our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins’ current valid General Terms and Conditions (AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/eeor retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title： Jim Gao/CEO Company: Shenzhen EZL Technology Co.,Ltd Address: 301-D24, Xiangjiang Financial Building, No.3046 Xinghai Avenue, Nanshan, Qianhai Shenzhen China 518000 Phone: +8619065068726 Fax: N/A E-Mail: [email protected]

FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 Appendix III EUT External Photographs Photo 1 Appearance of EUT Photo 2 Appearance of Adapter FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 Photo 3 Appearance of EUT Photo 4 Appearance of EUT FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 Photo 5 Appearance of EUT Photo 6 Appearance of EUT FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 Photo 7 Appearance of EUT Photo 8 Appearance of EUT FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 Photo 9 Appearance of EUT Photo 10 Appearance of EUT FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 Photo 11 Appearance of EUT

FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 Appendix IID Label Appendix II ID Label Location Wireless Bridge FCC ID: 2BGJ4-DLB523ACDISH Model: DLB 5-23ac DISH This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.

FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 Appendix IV EUT Internal Photographs Photo 12 Internal of EUT Photo 13 Appearance of PCB FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 Photo 14 Appearance of PCB Photo 15 Appearance of PCB FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 Photo 16 Appearance of PCB Photo 17 Appearance of PCB Antenna1 Antenna2 FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 Photo 18 Appearance of PCB

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202401-0239-2 Page: 1 of 4 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 Maximum Permissible Exposure Evaluation FCC ID: 2BGJ4-DLB523ACDISH 1. Client Information Applicant : Shenzhen EZL Technology Co.,Ltd Address : 301-D24, Xiangjiang Financial Building, No.3046 Xinghai Avenue, Nanshan, Qianhai Shenzhen China 518000 Manufacturer : Shenzhen EZL Technology Co.,Ltd Address : 301-D24, Xiangjiang Financial Building, No.3046 Xinghai Avenue, Nanshan, Qianhai Shenzhen China 518000 2. General Description of EUT EUT Name : Wireless Bridge Models No. : DLB 5-23ac DISH Model Different : ---- Brand Name : Ligowave Sample ID : HC-C-202401-0239-01-01-2# Operation Frequency : U-NII-1: 5180MHz~5240MHz; U-NII-2A: 5260MHz~5320MHz U-NII-2C: 5500MHz~5700MHz; U-NII-3: 5745MHz~5825MHz Modulation Type: 802.11a: OFDM (QPSK, BPSK, 16QAM, 64QAM) 802.11n: OFDM (QPSK, BPSK, 16QAM, 64QAM) 802.11ac: OFDM (QPSK, BPSK, 16QAM, 64QAM, 256QAM) Power Rating : AC Adapter (POE24G) Input: AC 100-240V~50/60Hz Out put: DC 24V⎓750mA Software Version : v1.0.18 Hardware Version : Rev1.0 Remark: (1) The adapter provided by the applicant, the verified for the RF conduction test provided by TOBY test lab. (2) Antenna information from antenna specification. Report No.: TBR-C-202401-0239-2 Page: 2 of 4 TB-RF-074-1.0 Method of Measurement for FCC 1. Max. Antenna Gain: Band Antenna Type Antenna Gain(dBi) Ant. 1 Ant. 2 5G U-NII-1 Internal 9.0 9.0 5G U-NII-2A 9.0 9.0 5G U-NII-2C 9.0 9.0 5G U-NII-3 9.0 9.0 2. EUT Operation Condition: Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 3. Exposure Evaluation: Equation from page 18 of OET Bulletin 65, Edition 97-01 S=(PG)/4πR 2 Where S: power density P: power input to the antenna G: power gain of the antenna in the direction of interest relative to an isotropic radiator. R: distance to the center of radiation of the antenna Simultaneous transmission MPE Considerations According to KDB447498: All transmitters and antennas in the host must be either evaluated for MPE compliance, by measurement or computational modeling, or qualify for the standalone MPE test exclusion in section 7.1. Simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on the calculated/estimated, numerically modeled or measured field strengths or power density, is ≤ 1.0. This means that: ∑ of MPE ratios ≤ 1.0 Report No.: TBR-C-202401-0239-2 Page: 3 of 4 TB-RF-074-1.0 4. Test Result: 5G Wi-Fi Worst MPE Result Test Mode Ant. Conducted Power(max) (dBm) Turn-up Power (dB) Max tune up power (dBm)[P] Max. ANT Gain (dBi)[G] Distance (cm) [R] Power Density (mW/ cm 2 ) [S] Limit (mW/ cm 2 ) 5G a-CDD Ant1 12.10 12±1 13 9.0 20 0.03153 1 5G n20-MIMO Ant1 12.53 12±1 13 9.0 20 0.03153 1 5G n40-MIMO Ant1 14.05 14±1 15 9.0 20 0.04997 1 5G ac20-MIMO Ant1 12.25 12±1 13 9.0 20 0.03153 1 5G ac40-MIMO Ant1 14.61 14±1 15 9.0 20 0.04997 1 5G ac80-MIMO Ant1 14.60 14±1 15 9.0 20 0.04997 1 5G Wi-Fi Worst MPE Result Test Mode Ant. Conducted Power(max) (dBm) Turn-up Power (dB) Max tune up power (dBm)[P] Max. ANT Gain (dBi)[G] Distance (cm) [R] Power Density (mW/ cm 2 ) [S] Limit (mW/ cm 2 ) 5G a-CDD Ant2 12.15 12±1 13 9.0 20 0.03153 1 5G n20-MIMO Ant2 12.59 12±1 13 9.0 20 0.03153 1 5G n40-MIMO Ant2 14.20 14±1 15 9.0 20 0.04997 1 5G ac20-MIMO Ant2 12.80 12±1 13 9.0 20 0.03153 1 5G ac40-MIMO Ant2 14.54 14±1 15 9.0 20 0.04997 1 5G ac80-MIMO Ant2 14.88 14±1 15 9.0 20 0.04997 1 Report No.: TBR-C-202401-0239-2 Page: 4 of 4 TB-RF-074-1.0 5. Conclusion: As specified in Table 1B of 47 CFR 1.1310- Limits for Maximum Permissible Exposure (MPE), Limits for General Population/ Uncontrolled Exposure Frequency Range (MHz) Power density (mW/ cm 2 ) 300-1,500 F/1500 1,500-100,000 1.0 For: 5G WIFI MPE limit S: 1mW/cm 2 The worst MPE is calculated as 0.04997mW / cm 2 < limit 1mW / cm 2 . 6. Summary simultaneous transmission information Modulation Type Work Frequency Band Transmit Antenna Antenna 1&2 Synchronization Transmit Ant. 1 Ant.2 IEEE 802.11a U-NII-1/ U-NII-2 A U-NII-2C/ U-NII-3 Yes Yes Yes IEEE 802.11n HT20 U-NII-1/ U-NII-2 A U-NII-2C/ U-NII-3 Yes Yes Yes IEEE 802.11n HT40 U-NII-1/ U-NII-2 A U-NII-2C/ U-NII-3 Yes Yes Yes IEEE 802.11ac VHT20 U-NII-1/ U-NII-2 A U-NII-2C/ U-NII-3 Yes Yes Yes IEEE 802.11ac VHT40 U-NII-1/ U-NII-2 A U-NII-2C/ U-NII-3 Yes Yes Yes IEEE 802.11ac VHT80 U-NII-1/ U-NII-2 A U-NII-2C/ U-NII-3 Yes Yes Yes 7. Summary simultaneous transmission results Band MPE Antenna 1 (mW/cm2) MPE Antenna 2 (mW/cm2) ∑MPE ratios Limit Results 5G WIFI 0.04997 0.04997 0.09994 1.0 PASS So, RF exposure limit warning or SAR test are not required. The EUT will only be used with a separation of 20cm or greater between the antenna and nearby persons and can therefore be considered a mobile transmitter per 47 CFR 2.1091 (b). The RF Exposure Information page from the manual is included here for reference. -----END OF THE REPORT-----

Productspecification QuickReferenceDate Antennafeed FrequencRange5100~5900MHz Ant.PortInputPwr.(dBm)23 Directivity(dBi)10 Efficiency(dB)80.2% Gain(dBi)9(AvgGainXY-plane) InputImpendence(ohm)50 PolarizationTypeVertical&Horizontal V.S.W.R<2.0 Antenna AntennaGain GainTable Frenq(MHz)510055005900Efficiency Gain(dBi)9.09.09.088.2% ReturnLoss TheEnvironmentofAntennaRadiationPattern 3Dradiationpatterndiagram XZ-planeYZ-planeXY-plane

Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202401-0239-3 Page: 1 of 288 FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 RF Test Data for 5G Wi-Fi (Conducted Measurements) General Description of EUT Product Name: Wireless Bridge Test Model: DLB 5-23ac DISH Sample ID: HC-C-202401-0239-01-01-2# Environmental Conditions Temperature: 23.8°C Relative Humidity: 48% Test Voltage: DC 24V Test Engineer: ZKN Zhou Note: For a more detailed features description, please refer to the report TBR-C-202401-0239-3 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202401-0239-3 Page: 2 of 288 FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 Contents 1. Emission Bandwidth....................................................................................................................................... 3 1.1.Test Result ......................................................................................................................................... 3 1.2.Test Graphs ....................................................................................................................................... 6 2. Occupied channel bandwidth ...................................................................................................................... 36 2.1.Test Result ....................................................................................................................................... 36 2.2.Test Graphs ..................................................................................................................................... 39 3. Min emission bandwidth ............................................................................................................................. 79 3.1.Test Result ....................................................................................................................................... 79 3.2.Test Graphs ..................................................................................................................................... 80 4. Maximum conducted output power ............................................................................................................ 90 4.1.Test Result ....................................................................................................................................... 90 5. Maximum power spectral density ............................................................................................................... 95 5.1.Test Result ....................................................................................................................................... 95 5.2.Test Graphs ................................................................................................................................... 100 6. Conducted Spurious Emission .................................................................................................................... 140 6.1.Test Result ..................................................................................................................................... 140 6.2.Test Graphs ................................................................................................................................... 146 7. Frequency Stability .................................................................................................................................... 224 7.1.Test Result ..................................................................................................................................... 224 8. Duty Cycle .................................................................................................................................................. 246 8.1.Test Result ..................................................................................................................................... 246 8.2.Test Graphs ................................................................................................................................... 249 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202401-0239-3 Page: 3 of 288 FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 1. Emission Bandwidth 1.1.Test Result TestMode Antenna Channel 26db EBW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict 11A-CDD Ant1 5180 19.28 5170.28 5189.56 --- --- Ant2 5180 19.76 5170.24 5190.00 --- --- Ant1 5200 19.64 5190.12 5209.76 --- --- Ant2 5200 19.36 5189.96 5209.32 --- --- Ant1 5240 19.44 5230.32 5249.76 --- --- Ant2 5240 19.64 5230.04 5249.68 --- --- Ant1 5260 19.32 5250.24 5269.56 --- --- Ant2 5260 19.68 5250.00 5269.68 --- --- Ant1 5280 19.08 5270.40 5289.48 --- --- Ant2 5280 19.20 5270.28 5289.48 --- --- Ant1 5320 20.04 5309.80 5329.84 --- --- Ant2 5320 19.24 5310.44 5329.68 --- --- Ant1 5500 19.76 5489.84 5509.60 --- --- Ant2 5500 19.72 5490.24 5509.96 --- --- Ant1 5580 19.96 5570.08 5590.04 --- --- Ant2 5580 19.40 5570.28 5589.68 --- --- Ant1 5700 21.44 5688.88 5710.32 --- --- Ant2 5700 21.88 5688.52 5710.40 --- --- 11N20- MIMO Ant1 5180 20.36 5169.76 5190.12 --- --- Ant2 5180 20.80 5169.52 5190.32 --- --- Ant1 5200 20.56 5189.60 5210.16 --- --- Ant2 5200 20.12 5189.84 5209.96 --- --- Ant1 5240 20.32 5229.76 5250.08 --- --- Ant2 5240 20.76 5229.56 5250.32 --- --- Ant1 5260 20.20 5249.80 5270.00 --- --- Ant2 5260 20.60 5249.68 5270.28 --- --- Ant1 5280 20.64 5269.68 5290.32 --- --- Ant2 5280 20.28 5269.72 5290.00 --- --- Ant1 5320 20.00 5309.76 5329.76 --- --- Ant2 5320 20.28 5309.80 5330.08 --- --- Ant1 5500 20.36 5489.60 5509.96 --- --- Ant2 5500 19.88 5490.08 5509.96 --- --- Ant1 5580 20.44 5569.68 5590…

Text truncated - open the document above for the full version.

Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202401-0239-3 Page: 73 of 288 FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 11AC40-MIMO_Ant2_5670 11AC40-MIMO_Ant1_5755 11AC40-MIMO_Ant2_5755 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202401-0239-3 Page: 74 of 288 FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 11AC40-MIMO_Ant1_5795 11AC40-MIMO_Ant2_5795 11AC80-MIMO_Ant1_5210 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202401-0239-3 Page: 75 of 288 FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 11AC80-MIMO_Ant2_5210 11AC80-MIMO_Ant1_5290 11AC80-MIMO_Ant2_5290 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202401-0239-3 Page: 76 of 288 FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 11AC80-MIMO_Ant1_5530 11AC80-MIMO_Ant2_5530 11AC80-MIMO_Ant1_5610 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202401-0239-3 Page: 77 of 288 FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 11AC80-MIMO_Ant2_5610 11AC80-MIMO_Ant1_5775 11AC80-MIMO_Ant2_5775 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202401-0239-3 Page: 78 of 288 FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202401-0239-3 Page: 79 of 288 FCC ID: 2BGJ4-DLB523ACDISH TB-RF-074-1.0 3. Min emission bandwidth 3.1.Test Result TestMode Antenna Channel 6db EBW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict 11A-CDD Ant1 5745 16.32 5736.72 5753.04 0.5 PASS Ant2 5745 16.32 5736.72 5753.04 0.5 PASS Ant1 5785 16.32 5776.72 5793.04 0.5 PASS Ant2 5785 16.32 5776.72 5793.04 0.5 PASS Ant1 5825 16.32 5…

Text truncated - open the document above for the full version.