2BGNX23SYM-QY0818BLUETOOTH CHRISTMAS DECOR

FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

6646158 Canada Inc 2024.07.01 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for 2BGNX23SYM-QY0818 [6646158 Canada Inc] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, ALEXIS BOUCHARD-A 6646158 Canada Inc 2024.07.01 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for 2BGNX23SYM-QY0818 [6646158 Canada Inc] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, ALEXIS BOUCHARD-A

Attestation Statements 2024.07.01 TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA RE: Attestation Statements Part 2.911(d)(7) request for 2BGNX23SYM-QY0818 (6646158 Canada Inc), the undersigned, hereby authorize (Menard, Inc) to act as our designated U.S. agent for service of process, (6646158 Canada Inc) accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. (Menard, Inc) accepts the responsibility to act as designated U.S. agent for service of process. Applicant Information： Company name: 6646158 Canada Inc Contact Name: ALEXIS BOUCHARD-A Address: 2251 Rue Lapierre, LaSalle, QC, H8N 1B7, CANADA Telephone No: 13926571679 Email: [email protected] Signature U.S. Agent Information: Company Name: Menard, Inc Address: 43325 State Hwy 55, Belgrade, MINNESOTA, 56312, USA FRN: 0025248485 Contact Name: FCC Contact Telephone No: (320)254-1043 Email: [email protected] Signature

Differences Description We 6646158 Canada Inc state: Product： BLUETOOTH CHRISTMAS DECOR Model Name： 23SYM-QY0818 Brand Name： N/A The electrical circuit design, layout, components used and internal wiring for above models are identical, Only the Model name is different. Sincerely, Company: 6646158 Canada Inc Title: President E-mail: [email protected] Name: ALEXIS BOUCHARD-A Signature

6646158 Canada Inc 2024-07-01 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (BLUETOOTH CHRISTMAS DECOR / 23SYM-QY0818 # AND 2BGNX23SYM-QY0818#) To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the • Schematics • Block diagram • Operation description required to be submitted with this application be permanently withheld from public review. These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Please contact me if there is any information you may need. Sincerely, Name: ALEXIS BOUCHARD-A

6646158 Canada Inc 2024-07-01 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize (Shenzhen STS Test Services Co., Ltd) to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Name: ALEXIS BOUCHARD-A

Page 1 of 5 Report No.: STS2405062 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Model: 23SYM-QY0818 Photo 1 Photo 2 Page 2 of 5 Report No.: STS2405062 Photo 3 Photo 4 Page 3 of 5 Report No.: STS2405062 Photo 5 Photo 6 Page 4 of 5 Report No.: STS2405062 Photo 7 Photo 8 Page 5 of 5 Report No.: STS2405062 Photo 9 Photo 10

Label BLUETOOTH CHRISTMAS DECOR Model: 23SYM-QY0818 FCC ID: 2BGNX23SYM-QY0818

Page 1 of 2 Report No.: STS2405062 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Model: 23SYM-QY0818 Photo 1 Photo 2 BLE ANTENA Page 2 of 2 Report No.: STS2405062 Photo 3

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the ShenZhen STS Test Services Co., Ltd. Radio Test Report Report No.: STS2405062H01 Issued for 6646158 Canada Inc 2251 Rue Lapierre, LaSalle, QC, H8N 1B7, CANADA Product Name: BLUETOOTH CHRISTMAS DECOR Brand Name: N/A Model Name: 23SYM-QY0818 Series Model(s): 23SYM-QYXXXX FCC ID: 2BGNX23SYM-QY0818 Test Standards: FCC 47CFR §2.1093 Page 2 of 9 Report No.: STS2405062H01 TEST REPORT Applicant’s Name ................. : 6646158 Canada Inc Address ................................. : 2251 Rue Lapierre, LaSalle, QC, H8N 1B7, CANADA Manufacturer's Name ........... : 6646158 Canada Inc Address ................................. : 2251 Rue Lapierre, LaSalle, QC, H8N 1B7, CANADA Product Description Product Name ........................ : BLUETOOTH CHRISTMAS DECOR Brand Name .......................... : N/A Model Name .......................... : 23SYM-QY0818 Series Model(s) ...................... : 23SYM-QYXXXX Test Standards ..................... : FCC 47CFR §2.1093 447498 D04 Interim General RF Exposure Guidance v01 The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the ShenZhen STS Test Services Co., Ltd. Date of Test ........................................... : Date of receipt of test item ...................... : 17 May 2024 Date (s) of performance of tests ............. : 17 May 2024 ~ 04 June 2024 Date of Issue .......................................... : 04 June 2024 Test Result .............................................. : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Chris Chen) Authorized Signatory : (Bovey Yang) Page 3 of 9 Report No.: STS2405062H01 TABLE OF CONTENTS 1. GENERAL INFORMATION 5 1.1 GENERAL DESCRIPTION OF THE EUT 5 1.2 TEST FACTORY 5 2. FCC 47CFR §2.1093 REQUIREMENT 6 2.1 TEST STANDARDS 6 2.2 LIMIT 6 2.3 TEST RESULT 9 Page 4 of 9 Report No.: STS2405062H01 Revision History Rev. Issue Date Report No. Effect Page Contents 00 04 June 2024 STS2405062H01 ALL Initial Issue Page 5 of 9 Report No.: STS2405062H01 1. GENERAL INFORMATION 1.1 GENERAL DESCRIPTION OF THE EUT Product Name BLUETOOTH CHRISTMAS DECOR Brand Name N/A Model Name 23SYM-QY0818 Series Model(s) 23SYM-QYXXXX Model Difference Only the Model name is different. Product Description The EUT is BLUETOOTH CHRISTMAS DECOR Operation Frequency: 2402~2480 MHz Modulation Type: GFSK Antenna gain: 0.55 dBi Antenna Designation: PCB antenna Rating Input: DC 5V 2A 10W Hardware Version N/A Software Version N/A 1.2 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 Page 6 of 9 Report No.: STS2405062H01 2. FCC 47CFR §2.1093 REQUIREMENT 2.1 TEST STANDARDS Follow the maximum permissible exposure (MPE) limits specified in 447498 D04 Interim General Radio Frequency Exposure Guidelines v01. The gain of the antenna used in the product was extracted from the supplied antenna data sheet and the maximum total power input to the antenna was also measured. Calculate the distance from the product to the MPE limit by the formula. 2.2 LIMIT For single RF sources (i.e., any single fixed RF source, mobile device, or portable device, as defined in paragraph (b)(2) of this section): A single RF source is exempt if: (A) The available maximum time-averaged power is no more than 1 mW, regardless of separation distance. This exemption may not be used in conjunction with other exemption criteria other than those in paragraph (b)(3)(ii)(A) of Part 1.1307. Medical implant devices may only use this exemption and that in paragraph (b)(3)(ii)(A); (B) Or the available maximum time-averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold Pth (mW) described in the following formula. This method shall only be used at separation distances (cm) from 0.5 centimeters to 40 centimeters and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by: Page 7 of 9 Report No.: STS2405062H01 (C) Or using below table and the minimum separation distance (R in meters) from the body of a nearby person for the frequency (f in MHz) at which the source operates, the ERP (watts) is no more than the calculated value prescribed for that frequency. For the exemption in Table 1 to apply, R must be at least λ/2π, where λ is the free-space operating wavelength in meters. If the ERP of a single RF source is not easily obtained, then the available maximum time-averaged power may be used in lieu of ERP if the physical dimensions of the radiating structure(s) do not exceed the electrical length of λ/4 or if the antenna gain is less than that of a half-wave dipole (1.64 linear value). RF Source frequency (MHz) Threshold ERP(watts) 0.3-1.34 1,920 R 2 . 1.34-30 3,450 R 2 /f 2 . 30-300 3.83 R 2 . 300-1,500 0.0128 R 2 f. 1,500-100,000 19.2R 2 . Page 8 of 9 Report No.: STS2405062H01 For multiple RF sources: Multiple RF sources are exempt if: (A) The available maximum time-averaged power of each source is no more than 1 mW and there is a separation distance of two centimeters between any portion of a radiating structure operating and the nearest portion of any other radiating structure in the same device, except if the sum of multiple sources is less than 1 mW during the time-averaging period, in which case they may be treated as a single source (separation is not required). This exemption may not be used in conjunction with other exemption criteria other than those is paragraph (b)(3)(i)(A) of Part 1.1307. Medical implant devices may only use this exemption and that in paragraph (b)(3)(i)(A). (B) in the case…

Text truncated - open the document above for the full version.

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the ShenZhen STS Test Services Co., Ltd. Radio Test Report Report No.: STS2405062H01 Issued for 6646158 Canada Inc 2251 Rue Lapierre, LaSalle, QC, H8N 1B7, CANADA Product Name: BLUETOOTH CHRISTMAS DECOR Brand Name: N/A Model Name: 23SYM-QY0818 Series Model(s): 23SYM-QYXXXX FCC ID: 2BGNX23SYM-QY0818 Test Standards: FCC 47CFR §2.1093 Page 2 of 9 Report No.: STS2405062H01 TEST REPORT Applicant’s Name ................. : 6646158 Canada Inc Address ................................. : 2251 Rue Lapierre, LaSalle, QC, H8N 1B7, CANADA Manufacturer's Name ........... : 6646158 Canada Inc Address ................................. : 2251 Rue Lapierre, LaSalle, QC, H8N 1B7, CANADA Product Description Product Name ........................ : BLUETOOTH CHRISTMAS DECOR Brand Name .......................... : N/A Model Name .......................... : 23SYM-QY0818 Series Model(s) ...................... : 23SYM-QYXXXX Test Standards ..................... : FCC 47CFR §2.1093 447498 D04 Interim General RF Exposure Guidance v01 The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the ShenZhen STS Test Services Co., Ltd. Date of Test ........................................... : Date of receipt of test item ...................... : 17 May 2024 Date (s) of performance of tests ............. : 17 May 2024 ~ 04 June 2024 Date of Issue .......................................... : 04 June 2024 Test Result .............................................. : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Chris Chen) Authorized Signatory : (Bovey Yang) Page 3 of 9 Report No.: STS2405062H01 TABLE OF CONTENTS 1. GENERAL INFORMATION 5 1.1 GENERAL DESCRIPTION OF THE EUT 5 1.2 TEST FACTORY 5 2. FCC 47CFR §2.1093 REQUIREMENT 6 2.1 TEST STANDARDS 6 2.2 LIMIT 6 2.3 TEST RESULT 9 Page 4 of 9 Report No.: STS2405062H01 Revision History Rev. Issue Date Report No. Effect Page Contents 00 04 June 2024 STS2405062H01 ALL Initial Issue Page 5 of 9 Report No.: STS2405062H01 1. GENERAL INFORMATION 1.1 GENERAL DESCRIPTION OF THE EUT Product Name BLUETOOTH CHRISTMAS DECOR Brand Name N/A Model Name 23SYM-QY0818 Series Model(s) 23SYM-QYXXXX Model Difference Only the Model name is different. Product Description The EUT is BLUETOOTH CHRISTMAS DECOR Operation Frequency: 2402~2480 MHz Modulation Type: GFSK Antenna gain: 0.55 dBi Antenna Designation: PCB antenna Rating Input: DC 5V 2A 10W Hardware Version N/A Software Version N/A 1.2 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 Page 6 of 9 Report No.: STS2405062H01 2. FCC 47CFR §2.1093 REQUIREMENT 2.1 TEST STANDARDS Follow the maximum permissible exposure (MPE) limits specified in 447498 D04 Interim General Radio Frequency Exposure Guidelines v01. The gain of the antenna used in the product was extracted from the supplied antenna data sheet and the maximum total power input to the antenna was also measured. Calculate the distance from the product to the MPE limit by the formula. 2.2 LIMIT For single RF sources (i.e., any single fixed RF source, mobile device, or portable device, as defined in paragraph (b)(2) of this section): A single RF source is exempt if: (A) The available maximum time-averaged power is no more than 1 mW, regardless of separation distance. This exemption may not be used in conjunction with other exemption criteria other than those in paragraph (b)(3)(ii)(A) of Part 1.1307. Medical implant devices may only use this exemption and that in paragraph (b)(3)(ii)(A); (B) Or the available maximum time-averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold Pth (mW) described in the following formula. This method shall only be used at separation distances (cm) from 0.5 centimeters to 40 centimeters and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by: Page 7 of 9 Report No.: STS2405062H01 (C) Or using below table and the minimum separation distance (R in meters) from the body of a nearby person for the frequency (f in MHz) at which the source operates, the ERP (watts) is no more than the calculated value prescribed for that frequency. For the exemption in Table 1 to apply, R must be at least λ/2π, where λ is the free-space operating wavelength in meters. If the ERP of a single RF source is not easily obtained, then the available maximum time-averaged power may be used in lieu of ERP if the physical dimensions of the radiating structure(s) do not exceed the electrical length of λ/4 or if the antenna gain is less than that of a half-wave dipole (1.64 linear value). RF Source frequency (MHz) Threshold ERP(watts) 0.3-1.34 1,920 R 2 . 1.34-30 3,450 R 2 /f 2 . 30-300 3.83 R 2 . 300-1,500 0.0128 R 2 f. 1,500-100,000 19.2R 2 . Page 8 of 9 Report No.: STS2405062H01 For multiple RF sources: Multiple RF sources are exempt if: (A) The available maximum time-averaged power of each source is no more than 1 mW and there is a separation distance of two centimeters between any portion of a radiating structure operating and the nearest portion of any other radiating structure in the same device, except if the sum of multiple sources is less than 1 mW during the time-averaging period, in which case they may be treated as a single source (separation is not required). This exemption may not be used in conjunction with other exemption criteria other than those is paragraph (b)(3)(i)(A) of Part 1.1307. Medical implant devices may only use this exemption and that in paragraph (b)(3)(i)(A). (B) in the case…

Text truncated - open the document above for the full version.

Prepared Checked Approved liang wangyuhua kenny Revision History: 2024-5-4 Rev.A0 1. MODEL： P/N（料号）： 2. Applications This antenna is designed for Bluetooth and it’s suitable for Bluetooth Product. 3. Electrical Characteristics Frequency Band：2400MHz～2500MHz Polarization *Gain : Max peak gain: 0.55 dBi Typ peak gain: 0 dBi Impedance：50Ω Material: PCB 23SYM-QY0818 Manufacturer: 6646158 Canada Inc BLE Antenna Specification Prepared Checked Approved liang wangyuhua kenny 4. Antenna Dimension 5. Typical Free Space Radiation Pattern 3D Radiation Pattern Prepared Checked Approved liang wangyuhua kenny 6. Typical Free Space Radiation Pattern 2D Radiation Pattern

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Radio Test Report Report No.:STS2405062W01 Issued for 6646158 Canada Inc 2251 Rue Lapierre, LaSalle, QC, H8N 1B7, CANADA Product Name: BLUETOOTH CHRISTMAS DECOR Brand Name: N/A Model Name: 23SYM-QY0818 Series Model(s): 23SYM-QYXXXX FCC ID: 2BGNX23SYM-QY0818 Test Standards: FCC Part15.247 Page 2 of 57 Report No.: STS2405062W01 TEST REPORT Applicant’s Name ................. : 6646158 Canada Inc Address ................................. : 2251 Rue Lapierre, LaSalle, QC, H8N 1B7, CANADA Manufacturer's Name .......... : 6646158 Canada Inc Address ................................. : 2251 Rue Lapierre, LaSalle, QC, H8N 1B7, CANADA Product Description Product Name ....................... : BLUETOOTH CHRISTMAS DECOR Brand Name .......................... : N/A Model Name .......................... : 23SYM-QY0818 Series Model(s) .................... : 23SYM-QYXXXX Test Standards ..................... : FCC Part15.247 Test Procedure ...................... : ANSI C63.10-2020 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Date of Test ........................................... : Date of receipt of test item ..................... : 17 May 2024 Date (s) of performance of tests ............. : 17 May 2024 ~ 04 June 2024 Date of Issue .......................................... : 04 June 2024 Test Result.............................................. : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Chris Chen) Authorized Signatory : (Bovey Yang) Page 3 of 57 Report No.: STS2405062W01 Table of Contents 1. SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 9 2.3 TEST SOFTWARE AND POWER LEVEL 9 2.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 10 2.5 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 11 2.6 EQUIPMENTS LIST 12 3. EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.2 TEST PROCEDURE 14 3.3 TEST SETUP 14 3.4 EUT OPERATING CONDITIONS 14 3.5 TEST RESULTS 15 4. RADIATED EMISSION MEASUREMENT 17 4.1 RADIATED EMISSION LIMITS 17 4.2 TEST PROCEDURE 19 4.3 TEST SETUP 20 4.4 EUT OPERATING CONDITIONS 20 4.5 FIELD STRENGTH CALCULATION 20 4.6 TEST RESULTS 22 5. CONDUCTED SPURIOUS & BAND EDGE EMISSION 29 5.1 LIMIT 29 5.2 TEST PROCEDURE 29 5.3 TEST SETUP 29 5.4 EUT OPERATION CONDITIONS 29 5.5 TEST RESULTS 29 6. POWER SPECTRAL DENSITY TEST 30 6.1 LIMIT 30 6.2 TEST PROCEDURE 30 6.3 TEST SETUP 30 Page 4 of 57 Report No.: STS2405062W01 Table of Contents 6.4 EUT OPERATION CONDITIONS 30 6.5 TEST RESULTS 30 7. BANDWIDTH TEST 31 7.1 LIMIT 31 7.2 TEST PROCEDURE 31 7.3 TEST SETUP 31 7.4 EUT OPERATION CONDITIONS 31 7.5 TEST RESULTS 31 8. PEAK OUTPUT POWER TEST 32 8.1 LIMIT 32 8.2 TEST PROCEDURE 32 8.3 TEST SETUP 33 8.4 EUT OPERATION CONDITIONS 33 8.5 TEST RESULTS 33 9. ANTENNA REQUIREMENT 34 9.1 STANDARD REQUIREMENT 34 9.2 EUT ANTENNA 34 APPENDIX 1-TEST DATA 35 1. DUTY CYCLE 35 2. MAXIMUM AVERAGE CONDUCTED OUTPUT POWER 38 3. MAXIMUM PEAK CONDUCTED OUTPUT POWER 41 4. -6DB BANDWIDTH 44 5. MAXIMUM POWER SPECTRAL DENSITY LEVEL 47 6. BAND EDGE 50 7. CONDUCTED RF SPURIOUS EMISSION 53 APPENDIX 2- EUT TEST PHOTO 57 Page 5 of 57 Report No.: STS2405062W01 Revision History Rev. Issue Date Report No. Effect Page Contents 00 04 June 2024 STS2405062W01 ALL Initial Issue Page 6 of 57 Report No.: STS2405062W01 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 15.247 Meas Guidance v05r02. FCC Part 15.247,Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS -- 15.247 (a)(2) 6dB Bandwidth PASS -- 15.247 (b)(3) Output Power PASS -- 15.209 Radiated Spurious Emission PASS -- 15.247 (d) Conducted Spurious & Band Edge Emission PASS -- 15.247 (e) Power Spectral Density PASS -- 15.205 Restricted bands of operation PASS -- Part 15.247(d)/ Part 15.209(a) Band Edge Emission PASS -- 15.203 Antenna Requirement PASS -- NOTE: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-20120. Page 7 of 57 Report No.: STS2405062W01 1.1 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 RF output power, conducted ±0.755dB 2 Unwanted Emissions, conducted ±2.874dB 3 All emissions, radiated 9K-30MHz ±3.80dB 4 All emissions, radiated 30M-1GHz ±4.18dB 5 All emissions, radiated 1G-6GHz ±4.90dB 6 All emissions, radiated>6G ±5.24dB 7 Conducted Emission (9KHz-150KHz) ±2.19dB 8 Conducted Emission (150KHz-30MHz) ±2.53dB 9 Occupied Channel Bandwidth ±3.5% 10 Power Spectral Density, conducted ±1.245dB 11 Duty Cycle ±3.2% Page 8 of 57 Report No.: STS2405062W01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name BLUETOOTH CHRISTMAS DECOR Brand Name N/A Model Name 23SYM-QY0818 Series Model(s) 23SYM-QYXXXX Model Difference Only the Model name is different. Product Description The EUT is a BLUETOOTH CHRISTM…

Text truncated - open the document above for the full version.

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Radio Test Report Report No.:STS2405062W01 Issued for 6646158 Canada Inc 2251 Rue Lapierre, LaSalle, QC, H8N 1B7, CANADA Product Name: BLUETOOTH CHRISTMAS DECOR Brand Name: N/A Model Name: 23SYM-QY0818 Series Model(s): 23SYM-QYXXXX FCC ID: 2BGNX23SYM-QY0818 Test Standards: FCC Part15.247 Page 2 of 57 Report No.: STS2405062W01 TEST REPORT Applicant’s Name ................. : 6646158 Canada Inc Address ................................. : 2251 Rue Lapierre, LaSalle, QC, H8N 1B7, CANADA Manufacturer's Name .......... : 6646158 Canada Inc Address ................................. : 2251 Rue Lapierre, LaSalle, QC, H8N 1B7, CANADA Product Description Product Name ....................... : BLUETOOTH CHRISTMAS DECOR Brand Name .......................... : N/A Model Name .......................... : 23SYM-QY0818 Series Model(s) .................... : 23SYM-QYXXXX Test Standards ..................... : FCC Part15.247 Test Procedure ...................... : ANSI C63.10-2020 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Date of Test ........................................... : Date of receipt of test item ..................... : 17 May 2024 Date (s) of performance of tests ............. : 17 May 2024 ~ 04 June 2024 Date of Issue .......................................... : 04 June 2024 Test Result.............................................. : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Chris Chen) Authorized Signatory : (Bovey Yang) Page 3 of 57 Report No.: STS2405062W01 Table of Contents 1. SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 9 2.3 TEST SOFTWARE AND POWER LEVEL 9 2.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 10 2.5 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 11 2.6 EQUIPMENTS LIST 12 3. EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.2 TEST PROCEDURE 14 3.3 TEST SETUP 14 3.4 EUT OPERATING CONDITIONS 14 3.5 TEST RESULTS 15 4. RADIATED EMISSION MEASUREMENT 17 4.1 RADIATED EMISSION LIMITS 17 4.2 TEST PROCEDURE 19 4.3 TEST SETUP 20 4.4 EUT OPERATING CONDITIONS 20 4.5 FIELD STRENGTH CALCULATION 20 4.6 TEST RESULTS 22 5. CONDUCTED SPURIOUS & BAND EDGE EMISSION 29 5.1 LIMIT 29 5.2 TEST PROCEDURE 29 5.3 TEST SETUP 29 5.4 EUT OPERATION CONDITIONS 29 5.5 TEST RESULTS 29 6. POWER SPECTRAL DENSITY TEST 30 6.1 LIMIT 30 6.2 TEST PROCEDURE 30 6.3 TEST SETUP 30 Page 4 of 57 Report No.: STS2405062W01 Table of Contents 6.4 EUT OPERATION CONDITIONS 30 6.5 TEST RESULTS 30 7. BANDWIDTH TEST 31 7.1 LIMIT 31 7.2 TEST PROCEDURE 31 7.3 TEST SETUP 31 7.4 EUT OPERATION CONDITIONS 31 7.5 TEST RESULTS 31 8. PEAK OUTPUT POWER TEST 32 8.1 LIMIT 32 8.2 TEST PROCEDURE 32 8.3 TEST SETUP 33 8.4 EUT OPERATION CONDITIONS 33 8.5 TEST RESULTS 33 9. ANTENNA REQUIREMENT 34 9.1 STANDARD REQUIREMENT 34 9.2 EUT ANTENNA…

Text truncated - open the document above for the full version.