2BGXK-RE033REMOTE CONTROL

Remote controller GENERAL INFORMATION 1.INSTALLING RECEIVER IN CEILING FAN A. Safety precautions: Do not use with solid state fans. electrical code requirements. C. Installing receiver in fan: a. Remove power from the circuit. bracket. Supply in electrical junction box. supplied: B. Electrical rating: 110/240V 50/60Hz Electrical wire must meet all local and national Otherwise power can cause serious injury or death. b. Remove ceiling fan canopy from the mounting c. Disconnect existing wiring between ceiling fan and d. Make connections as follows, using the wire nuts MAX. Motor watts: 40W MAX. Light watts: 60W (FIG.1) (FIG.2) Use wire connecting nuts supplied with the fan FROM POWER SOURCE AC 110~240 VOLT 50/60Hz CONNECT TO Green fan wire ....Bare supply wire Black receiver wire(AC IN L) ....Black supply wire White receiver wire(AC IN N) ....White supply wire Brown receiver wire(TO MOTOR 1) ....Brown fan wire Black receiver wire(TO MOTOR 2) ....Black fan wire Red receiver wire(TO MOTOR3) ....Red fan wire Blue receiver wire(For light) ....Blue light wire White receiver wire(For light) ....white light wire CANOPY (FIG.2) ANTENNA PUT AT OUTSIDE OF CANOPY BOX CAN GET MORE OPERATION DISTANCE RECEIVER (FIG.1) WHITE INPUT OUTPUT RED or BLACK ANT CANOPY R EC E IV E R OUTPUT LIGHT MOTOR 2.OPERATING TRANSMITTER: A. Install 2032 3 volt battery. (To prevent damage to transmitter, remove the battery if not used for a long time). B. Store the transmitter away from excessive heat or humidity. C. Operating the buttons on the panel of the transmitter. (FIG.3) (FIG.3) Light ON/OFF - FAN ON/OFF + Light Dimmer + Fan Speed Foward/Reverset Battery: Fan Speed (FIG.4) CR2032 3V LEARN The Learn Key must be pressed with in 5 seconds, after pressing the Power button. If not, please press the Power button to restart. Keep pressing the button LEARN key in excess of 3 second it becomes a LEARN status. The receiver can remember the last codes status . The ceiling fan light flash two times. D. Setting the codes on the receiver: (FIG.4) D. Keep pressing the light button in excess of 0.7 second and it becomes a dimmer. Light Dimmer - Time 2 Hour FCC Statement: 1.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference. (2)This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15 or the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may casue harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --- Reorient or relocate the receiving antenna. --- Increase the separation between the equipment and receiver. --- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --- Consult the dealer or an experienced radio/ TV technician for help. Statement according to FCC part 15.21: Changes or modifications not expressly approved by the party responsible for compliancecould void the user's authority to operate the equipment. WARNING:

Hefei Eileen Grays Smart Technology Co., Ltd. Covered Equipment Certification Attestation Letter 6/12/2024 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2BGXK-RE033 Hefei Eileen Grays Smart Technology Co., Ltd. certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Hefei Eileen Grays Smart Technology Co., Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Signed: Printed name: Zai Ping Tang Title: CEO Company Name: Hefei Eileen Grays Smart Technology Co., Ltd. Date: 6/12/2024

Hefei Eileen Grays Smart Technology Co., Ltd. * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2BGXK-RE033 FRN of applicant: 0035548213 Per section 2.911(d)(7) of the FCC rules, Hefei Eileen Grays Smart Technology Co., Ltd. certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: Baihetian Innovative Solutions FCC Registration Number (FRN): 0033401605 Physical U.S. Company Address: 6837 Chase Rd, Dearborn, MI 48126, USA Contact Person: Kenneth Young Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Signed: Printed name: Zai Ping Tang Title: CEO Company Name: Hefei Eileen Grays Smart Technology Co., Ltd. Date: 6/24/2024 Agent Signed: Signed: Printed name: Kenneth Young Title: Manager Company Name: Baihetian Innovative Solutions Date: 6/24/2024

< Hefei Eileen Grays Smart Technology Co., Ltd.> Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD21046 Date: 2024-06-12 Subject; Request for Long Term Confidentiality FCC ID: 2BGXK-RE033 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Pursuant to Public Notice DA 04-1705 of the Commission' s policy, in order to comply with the marketing regulations in 47 CFT §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuanttoKDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Zai Ping Tang Title: CEO

Page 1 of 5 Test Model No.: RE‐033 Page 2 of 5 Page 3 of 5 Page 4 of 5 Page 5 of 5

MODEL: RE-033 FCC ID: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO T HE FOLLOWING T WO CONDITIONS: (1)T HIS DEVICE INTERFERENCE A ND MAY NOT CAUSE HARMFUL. (2)T HIS DEVICE MUST A CCEPT A NY INTERFERENCE RECEIVED. INCLUDING INTERFERENCE T HAT MAY CAUSE SIZE: 30*20MM UNDESIRED OPERATION 银底黑字 RE-033 标贴 2BGXK-RE033 MODEL: RE-033 FCC ID: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO T HE FOLLOWING T WO CONDITIONS: (1)T HIS DEVICE INTERFERENCE A ND MAY NOT CAUSE HARMFUL. (2)T HIS DEVICE MUST A CCEPT A NY INTERFERENCE RECEIVED. INCLUDING INTERFERENCE T HAT MAY CAUSE UNDESIRED OPERATION 2BGXK-RE033

Page 1 of 2 Test Model No.: RE‐033 Page 2 of 2

RF Exposure evaluation According to 447498 D04 Interim General RF Exposure Guidance v01 limit (mW) min. distance (cm) 433.92 83.29 23.17 0.50 According to ANSI C63.10 Where: Then SAR evaluation is not required FCC ID: 2BGX K -RE033 Frequency(MHz)Field Strength (dBuV /m) EIRP (dBm)=E(dBuV /m)-95.2 ERP= EIRP-2.15dB E =Field Strength (dBuV /m)So ERP=83.29-95.2-2.15=-14.06dBm O utput pow er (mW) 0.116

Report No.: RF240507004-01-002 Page 1 Total 9 Product ModelSecurity Classification RE-033Confidential HW Version/ SW Version/ Total 9 pages Antenna Test Report Prepared By:Reviewed byApproved By: Kieron LuoVic CaiFlank Wang Report No.: RF240507004-01-002 Page 2 Total 9 Revision History VersionRevised DateChange DescriptionEditor Report No.: RF240507004-01-002 Page 3 Total 9 Table of Contents 1. Basic information .....................................................................................................................4 2. Test equipments ......................................................................................................................4 3. Test conclusion ........................................................................................................................4 4. Pass criteria ..............................................................................................................................4 5. Test method..............................................................................................................................5 6. Test result .................................................................................................................................6 7. Test picture ...............................................................................................................................7 8. Photographs of ANT ................................................................................................................8 Report No.: RF240507004-01-002 Page 4 Total 9 1. Basic information DUT Model RE-033 Adapter Model/ Quantity & SN1 set Test Date2024-05-16 2. Test equipments NameManufacturerModelUseful-life Network analyzerAgilentE5071C2024-10-11 Microwave Anechoic Chamber T&W lab /2024-10-24 3. Test conclusion Test ResultPASS Note: 4. Pass criteria 1) Electrical Properties Frequency Range:433.05MHz~434.79MHz Gain : -2.57 dBi 2) Physical Properties Operating Temp: -10°C~+60°C Storage Temp: -10°C~+70°C Report No.: RF240507004-01-002 Page 5 Total 9 5. Test method Test set-up as follow practicality pictures： Report No.: RF240507004-01-002 Page 6 Total 9 6. Test result Frequency (GHz)Gain (dBi)Efficiency (%)Result 433.05MHz~434.79MHz-2.575.55%PASS FrequencyGainEfficiency [MHz][dBi][%] 430-2.60795.5054 431-2.58295.5366 432-2.56795.5526 433-2.56825.5257 434-2.60115.4482 435-2.66145.3346 436-3.23385.2206 437-3.32055.1359 438-3.38045.093 439-3.40055.0975 440-3.38785.1504 Report No.: RF240507004-01-002 Page 7 Total 9 7. Test picture 1) 2D Radiation Pattern: Report No.: RF240507004-01-002 Page 8 Total 9 8. Photographs of ANT Report No.: RF240507004-01-002 Page 9 Total 9 ---------------------------------------------------The end-------------------------------------------------------

Global United Technology Services Co., Ltd. Report No.: GTS2024040350F01 Authorized Signature: Robinson Luo Laboratory Manager This results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Page 1 of 23 TEST REPORT Applicant: Hefei Eileen Grays Smart Technology Co., Ltd. Address of Applicant: Rm 1707-1710, block D, Weilan Business port, Qianshan Rd, Zhengwu District, Hefei, Anhui, China Manufacturer: San Sheng (Zhongshan) Electronic Technology Co.,Ltd. Address of Manufacturer: Torch Development Zone,No.1 Jiangling West Road, Zhongshan City,Guangdong Province,China Equipment Under Test (EUT) Product Name: REMOTE CONTROL Model No.: RE-033 FCC ID: 2BGXK-RE033 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.231 Date of sample receipt: April 22, 2024 Date of Test: April 23, 2024-May 16, 2024 Date of report issued: May 16, 2024 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: GTS2024040350F01 Global United Technology Services Co., Ltd. No.123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 23 2 Version Version No. Date Description 01 May 16, 2024 Original Prepared By: Date: May 16, 2024 Project Engineer Check By: Date: May 16, 2024 Reviewer Report No.: GTS2024040350F01 Global United Technology Services Co., Ltd. No.123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 23 3 Contents Page 1 COVER PAGE .......................................................................................................................................... 1 2 VERSION .................................................................................................................................................. 2 3 CONTENTS .............................................................................................................................................. 3 4 TEST SUMMARY ..................................................................................................................................... 4 4.1 MEASUREMENT UNCERTAINTY ............................................................................................................ 4 5 GENERAL INFORMATION ...................................................................................................................... 5 5.1 GENERAL DESCRIPTION OF EUT ......................................................................................................... 5 5.2 TEST MODE ........................................................................................................................................ 6 5.3 DESCRIPTION OF SUPPORT UNITS ....................................................................................................... 6 5.4 TEST FACILITY .................................................................................................................................... 6 5.5 TEST LOCATION ................................................................................................................................. 6 5.6 OTHER INFORMATION REQUESTED BY THE CUSTOMER ......................................................................... 6 5.7 ADDITIONAL INSTRUCTIONS ................................................................................................................. 6 6 TEST INSTRUMENTS LIST ..................................................................................................................... 7 7 TEST RESULTS AND MEASUREMENT DATA ...................................................................................... 9 7.1 ANTENNA REQUIREMENT ..................................................................................................................... 9 7.2 RADIATED EMISSION METHOD ........................................................................................................... 10 7.2.1 Field Strength of The Fundamental Signal ................................................................................ 12 7.2.2 Spurious Emissions ................................................................................................................... 14 7.3 20DB OCCUPY BANDWIDTH .............................................................................................................. 19 7.4 DEACTIVATION TESTING .................................................................................................................... 21 8 TEST SETUP PHOTO ............................................................................................................................ 23 9 EUT CONSTRUCTIONAL DETAILS ..................................................................................................... 23 Report No.: GTS2024040350F01 Global United Technology Services Co., Ltd. No.123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 4 of 23 4 Test Summary Test Item Section in CFR 47 Result Antenna Requirement 15.203 Pass Conduction Emission 15.207 N/A Field strength of the Fundamental Signal 15.231 (b) Pass Spurious Emissions 15.231 (b)/15.209 Pass 20dB Bandwidth 15.231 (c) Pass Deactivation Testing Pass N/A: Not applicable. 4.1 Measurement Uncertainty Test Item Frequency Range Measurement Uncertainty Notes Radiated Emission 30MHz-200MHz 3.8039dB (1) Radiated Emission 200MHz-1GHz 3.9679dB (1) Radiated Emission …

Text truncated - open the document above for the full version.

Page 1 of 1 Test Model No.: RE‐033 Radiated Emission