2BGXO-D2Wireless Transmitting Charger

说明书 使用前请仔细阅读 产品名称：无线发射充电器 型号：D2 材质：铝合金＋聚碳酸酯 输入电流：500mA--0.6A MAX 接口： type-C 输入电压：5V_DC 输出功率：2.5W 工作温度：-10C至50C 环境湿度： 35%~85% 裸机重量：约6.0g（不含包装） 颜色：黑、银、红、蓝、绿、金 产品尺寸：27.6mm*7.1mm 产品内置过流•;过压•;温度保护等多重安全保护电路•.兼容大多数iWatch型号 使用注意事项 •请与Lightning数据线或者 USB Type-C 数据线搭配使用，不支持QC协议大功率充头，不怡当的使用可能会使设备不能正常工作以及发热损坏设备 •注意连接器零件上的液体(汗液、饮用水等)或异物，小心不要让灰尘、金属件等粘附; •充电时务必避免受潮 •请勿靠近火源 •请勿用湿手触摸电源 •请勿拆解或修改 •当电缆磨损、绝缘层破损时，切勿使用带有插头的设备 •建议您在取下手表保护套的情况下为你的watch充电 英语 Please read carefully before use Product Name: Wireless Transmitting Charger Model: D2 Material: aluminum alloy + polycarbonate Input current: 500 mA--0.6A MAX interface: type-C Input voltage: 5 V _ DC Output Power: 2.5W Operating temperature: -10 C to 50 C Ambient humidity: 35% ~ 85% Bare metal weight: approximately6.0 g (without packaging) Product size:27.6mm* 7.1mm Color: Black, Silver, Red, Blue, Green, Gold Product built-in over-current, over-voltage, temperature protection and other multiple security protection circuit compatible with most iWatch models The use of caution · Please use with Lightning digital cable or USB Type-C digital cable, do not support QC protocol high-power charging head, Improper use may make the equipment not work properly and heat damage the equipment · Pay attention to liquids (sweat, drinking water, etc.) or foreign objects on the connector parts, be careful not to let dust, metal parts, etc. adhere; · Be sure to avoid moisture when charging · Keep away from fire · Do not touch the power supply with wet hands · Do not disassemble or modify · When cables are worn out.Do not use equipment with plugs if insulation is damaged · It is recommended that you charge your watch with the watch case removed Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 意大利文 Si prega di leggere attentamente prima di utilizzare Nome del prodotto: caricabatterie di trasmissione wireless Modello: D2 Materiale: lega di alluminio + policarbonato Corrente di ingresso: 500mA -- 0.6A MAX Porto:type-C Tensione di ingresso: 5V_DC Potenza di uscita: 2.5W Temperatura di funzionamento: -10C a 50C Umidità ambiente: 35% ~ 85% Peso della macchina nuda: circa6.0 g (senza imballaggio) Dimensioni del prodotto: 27.6mm*7.1mm Colore: nero, argento, rosso, blu, verde, oro Multi circuiti di protezione integrati, tra cui sovracorrente, sovratensione, protezione dalla temperatura, compatibile con la maggior parte dei modelli di iWatch Precauzioni per l'uso • Utilizzare con un cavo Lightning o USB Type-C, Non supporta il protocollo QC ad alta potenza, L'uso improprio può impedire il funzionamento dell'apparecchiatura e danneggiare l'apparecchiatura dal calore • Attenzione ai liquidi (sudore, acqua potabile, ecc.) o ai corpi estranei sulle parti del connettore, Fare attenzione a non lasciare che la polvere, i pezzi metallici ecc. aggrappano; • Evitare l'umidità durante la ricarica • Non avvicinarsi alla fonte di fuoco • Non toccare l'alimentazione con le mani bagnate • Non smontare o modificare • Quando il cavo si stacca, 日语 ご使用前によくお読みください。 製品名:ワイヤレス送信充電器 型号:D2 材質:アルミニウム合金+ポリカーボネート 入力電流:500mA--0.6A MAX インターフェース:type-C 入力電圧:5V_DC 出力電力：2.5W 工作温度:-10C～50C 周囲濕度:35%~85% 裸機重量:約6.0g(梱包なし) 製品サイズ:27.6mm*7.1mm 色:黒、銀、赤、青、緑、金 製品内蔵過電流過電圧温度保護など多重安全保護回路・ほとんどのiWatchモデルに対応 使用上の注意点 LightningケーブルまたはUSB Type-Cケーブルと組み合わせて使用してください。QCプロトコルの高電力ヘッドはサポートさ れず、不適切な使用により機器が正常に作動し、発熱により機器が損傷する恐れがあります。コネクタ部品上の液体(汗、飲 料水など)や異物に注意してください。塵や金属部品等が付着しないように注意する。 •充電時には濕気を避けてください•火源に近づかないでください •濡れた手で電源に触れないでください•分解または変更しないでください •ケーブルが磨耗するとき、絶縁層が破損した場合、プラグ付き機器は使用しないでください •腕時計カバーを取り外した状態で腕時計を充電することをお勧めします。 法文 Veuillez lire attentivement avant d'utiliser. Nom du produit : Chargeur d'émission sans fil Numéro de modèle : D2 Matériel : alliage d'aluminium + polycarbonate Courant d'entrée : 500mA -- 0.6A MAX Port: type-C Tension d'entrée : 5V_DC Puissance de sortie: 2.5W Température de fonctionnement : -10C à 50C Humidité de l'environnement : 35 % ~ 85% Poids nu : environ6.0 g (sans emballage) Dimension du produit : 27.6mm*7.1mm Couleur : noir, argent, rouge, bleu, vert, or Multiples circuits de protection de sécurité intégrés, tels que surcoulement, surtension, protection contre la température, compatible avec la plupart des modèles iWatch Attention à l'utilisation • Utilisez avec un câble Lightning ou un câble USB Type-C, Le chargeur haute puissance ne prend pas en charge le protocole QC, Une mau…

Text truncated - open the document above for the full version.

Rev 1/26/2023 Shenzhen Sanda Weiye Technology Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 01-22-2026 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2BGXO-D2 [Shenzhen Sanda Weiye Technology Co., Ltd.] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [Shenzhen Sanda Weiye Technology Co., Ltd.] certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, Signature： By: Lemon feng Rev 1/26/2023 Shenzhen Sanda Weiye Technology Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 01-22-2026 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2BGXO-D2 [Shenzhen Sanda Weiye Technology Co., Ltd.] certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Signature： By: Lemon feng

Shenzhen Sanda Weiye Technology Co., Ltd. U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: January 22, 2026 Ref: Attestation Statement – Part 2.911(d)(7) filing FCC ID: 2BGXO-D2 Shenzhen Sanda Weiye Technology Co., Ltd.(“the applicant”) certifies that, as of the date of the filing of the application, CLF Import and Export Limited (“the agent”) is our designated U.S. agent for service of process for the above reference FCC ID. The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges it is our responsibility to inform the FCC whenever the agent information changes. CLF Import and Export Limited ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name: CLF Import and Export Limited FRN: 0033489683 Address: 1312 17th Street #692, Denver, CO 80202, United States Signature: Contact Person: David Chen Tel: +1 949 254 2565 Email: [email protected] Applicant Company Name: Shenzhen Sanda Weiye Technology Co., Ltd. FRN: 0035548254 Address: 2nd Floor, Building 8, No. 27, Wunipeng Road, Third Industrial Zone, Shaqi Community Xinqiao Street, Bao'an District, Shenzhen China Signature: Contact Person: Lemon feng Tel: 18211307641 Email: [email protected]

L LCX-C-14 深圳市立诚兴科技有限公司 Shenzhen Lichengxing Technology Co., Ltd. 承 认 书 客戶： CUSTOMER: SPECIFICATION FOR APPROVAL Shenzhen Sidawei Technology Co., Ltd. (KH178) 客 戶 料 號： CUST P/N: 内部 料 號 ： LCX P/N: 産 品 型 號： DESC: 日期： DATE: 版本： Version: D2 LCX-KH178017 Φ14.5*21-0.08*24P-13TS-6-23NMJ 2026/1/5 A.0 制作 PREPARED BY 审核 CHECKED BY 批准 APPROVED BY 客戶承认 CUSTOMER APPROVE 杨文俊 2026/1/5 高应洪 2026/1/5 site：No. 365, Xinhu Road, Niuhu Community, Guanlan Street, Longhua District, Shenzhen City phone： 13828741697 E-mail:[email protected] LCX-C-14 产品规格书SPECIFICATION 图纸编号：LCX-GCQP0001349 版本 A/0 制作：杨文俊 2026/1/5 审核：高应洪 2026/1/5 页码：3/4客户代码：CUST KH178 规格型号 Φ 14.5*21-0.08*24P-13TS-6-23NMJ 客户料号：CUST P/N D2 内部料号：IN P/N LCX-KH178017 ABCEFHH1 H2 ------------------ 14.5 ±0.3 20-21 23 ±0.3 6 ±1 3 ±1 0.9 ±0.15 0.17 ±0.03 1.1±0.15 ------------------ I. Dimensions (in mm): Winding mold: Diameter: 14.5 mm; Coil weight: 0.96 kg 二、原理图SCHEMATIC DIAGRAM: 三、绕线参数Winding Specification: 序号 NO 端子 TERMINAL 线径 WIRE 线材分解温度 Temperature 圈数 Turns 绕线方向 Winding Direction L1SF Multi-strand enameled wire 0.08 * 24P 180-250 13TS anticlockwise 四、电气特性ELECTRICAL CHARACTERISTIC：: 温度TEMPERATURE:25±10°C,湿度RELATIVE HUMIDITY:65±20% 序号 NO 磁片材质 Disk material 电感量 LS 阻抗 DCR 测试条件 TEST FREQUENCY 测试仪器 TEST EQUIPMENTS L14.3uH±10% 115mΩ ±10% 100KHz/1.0VU2832 L2 Hard magnetic sheet 6.9uH±5% 115mΩ±10% 100KHz/1.0V U2832

Shenzhen Sanda Weiye Technology Co., Ltd. Date: January 22, 2026 Product Model Number: D2, D2 Pro FCC ID: 2BGXO-D2 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following: • Testing • Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. Contact Listed on FCC Wesbite Signature： By: Lemon feng Title: Manager Email: [email protected] Telephone: 18211307641 On behalf of: Shenzhen Sanda Weiye Technology Co., Ltd.

Shenzhen Sanda Weiye Technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: January 22, 2026 Subject; Request for Confidentiality FCC ID: 2BGXO-D2 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature： By: Lemon feng Title: Manager

Shenzhen Sanda Weiye Technology Co., Ltd. Model Difference Statement Dear Sir/Madam, FCC ID: 2BGXO-D2 Date: January 22, 2026 Added models D2 Pro basis of the original product D2 The manufacturer declares that the listed series models have different appearance colors, shapes and model names from the main model, but the circuits and electronic structures are the same. Sincerely, Signature： By: Lemon feng Title: Manager Email: [email protected] Telephone: 18211307641 On behalf of: Shenzhen Sanda Weiye Technology Co., Ltd.

Report No: SSP26010103-1E FCC ID: 2BGXO-D2 Annex of Test Report Annex A. EUT External Photos Model: D2 EUT View 1 EUT View 2 Report No: SSP26010103-1E FCC ID: 2BGXO-D2 Annex of Test Report EUT View 3 EUT View 4 Report No: SSP26010103-1E FCC ID: 2BGXO-D2 Annex of Test Report EUT View 5 EUT View 6

Report No: SSP26010103-1E FCC ID: 2BGXO-D2 Annex of Test Report Annex D. Label and Information FCC Label Sample Label Size : 20mm*15mm FCC Label Specifications Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Where the EUT is constructed in two or more sections connected by wires and marketed together, the above statement is required to be affixed only to the main control unit. When the EUT is so small or for such use that it is not practicable to place the statement on it, the above information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. FCC Label Location

Report No: SSP26010103-1E FCC ID: 2BGXO-D2 Annex of Test Report Annex B. EUT Internal Photos EUT Internal View 1 EUT Internal View 2 Coil Antenna Report No: SSP26010103-1E FCC ID: 2BGXO-D2 Annex of Test Report EUT Internal View 3 EUT Internal View 4

Report No: SSP26010103-2H FCC Test Report Page 1 of 10 RF Exposure Report FCC ID: 2BGXO-D2 Report No. : SSP26010103-2H Applicant : Shenzhen Sanda Weiye Technology Co., Ltd. Product Name : Wireless Transmitting Charger Model Name : D2 Test Standard : FCC CFR 47 PART 1, 1.1310 Date of Issue : 2026-01-19 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.ccuttest.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: SSP26010103-2H FCC Test Report Page 2 of 10 Test Report Basic Information Applicant..................................: Shenzhen Sanda Weiye Technology Co., Ltd. Address of Applicant...............: 2nd Floor, Building 8, No. 27, Wunipeng Road, Third Industrial Zone, Shaqi Community Xinqiao Street, Bao'an District, Shenzhen China Manufacturer..........................: Shenzhen Sanda Weiye Technology Co., Ltd. Address of Manufacturer........: 2nd Floor, Building 8, No. 27, Wunipeng Road, Third Industrial Zone, Shaqi Community Xinqiao Street, Bao'an District, Shenzhen China Product Name.........................: Wireless Transmitting Charger Brand Name.............................: - Main Model..............................: D2 Series Models..........................: D2 Pro Test Standard..........................: FCC CFR 47 PART 1, 1.1310 KDB 680106 D01 Wireless Power Transfer v04 Date of Test .............................: 2026-01-09 to 2026-01-14 Test Result...............................: PASS Tested By ................................: (Colin Chen) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: SSP26010103-2H FCC Test Report Page 3 of 10 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Test Facilities ........................................................................................................................................................6 1.4 List of Measurement Instruments ..........................................................................................................................7 1.5 Measurement Uncertainty .....................................................................................................................................7 2. RF Exposure .................................................................................................................................................................8 2.1 Standard and Limit................................................................................................................................................8 2.2 Test Procedures ....................................................................................................................................................8 2.3 Test Data and Results ............................................................................................................................................9 Annex A. Test Photos ..................................................................................................................................................... 10 Report No: SSP26010103-2H FCC Test Report Page 4 of 10 Revision History Revision Issue Date Description Revised By V1.0 2026-01-19 Initial Release Lahm Peng Report No: SSP26010103-2H FCC Test Report Page 5 of 10 1. General Information 1.1 Product Information Product Name: Wireless Transmitting Charger Trade Name: - Test Model: D2 Series Models: D2 Pro Rated Voltage: Input: 5V⎓0.5A-0.6A Max Wireless Output: 2.5W Battery: - Test Sample No: SSP26010103-1 Hardware Version: V1.0 Software Version: V1.0 Note 1: The test data is gathered from a production sample, provided by the manufacturer. Note 2: The manufacturer declares that the listed series models have different appearance colors, shapes and model names from the main model, but the circuits and electronic structures are the same. Wireless Specification Wireless Standard: WPC (QI) Operating Frequency: (Watch):310kHz-340kHz Modulation: ASK Antenna Gain: 0dBi Type of Antenna: Coil Antenna Type of Device: Portable Device Mobile Device Report No: SSP26010103-2H FCC Test Report Page 6 of 10 1.2 Test Setup Information List of Test Modes Test Mode Description Remark TM1 Wireless charging 2.5W - TM2 - - TM3 - - Note: All modes have been tested and only the worst mode TM1 data is represented in the report. List and Details of Auxiliary Cable Description Length (cm) Shielded/Unshielded With/Without Ferrite - - - - List and Details of Auxiliary Equipment Description Manufacturer Model Serial Number Adapter UGREEN CD289 90324 Apple Watch iPhone A2855 GK46LFW525 1.3 Test Facilities Laboratory Name: Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China CNAS Laboratory No.: L18863 A2LA Certificate No.: 6983.01 FCC Registration No: 583813 ISED Registration No.: CN0164 Report No: SSP26010103-2H FCC Test Report Page 7 of 10 1.4 List of Measurement Instrument…

Text truncated - open the document above for the full version.

Report No: SSP26010103-1E FCC Test Report Page 1 of 23 FCC TEST REPORT FCC ID: 2BGXO-D2 Report No. : SSP26010103-1E Applicant : Shenzhen Sanda Weiye Technology Co., Ltd. Product Name : Wireless Transmitting Charger Model Name : D2 Test Standard : FCC Part 15 Subpart C Date of Issue : 2026-01-19 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.ccuttest.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: SSP26010103-1E FCC Test Report Page 2 of 23 Test Report Basic Information Applicant..................................: Shenzhen Sanda Weiye Technology Co., Ltd. Address of Applicant...............: 2nd Floor, Building 8, No. 27, Wunipeng Road, Third Industrial Zone, Shaqi Community Xinqiao Street, Bao'an District, Shenzhen China Manufacturer..........................: Shenzhen Sanda Weiye Technology Co., Ltd. Address of Manufacturer........: 2nd Floor, Building 8, No. 27, Wunipeng Road, Third Industrial Zone, Shaqi Community Xinqiao Street, Bao'an District, Shenzhen China Product Name.........................: Wireless Transmitting Charger Brand Name.............................: - Main Model..............................: D2 Series Models..........................: D2 Pro Test Standard..........................: FCC Part 15 Subpart C ANSI C63.4-2014 ANSI C63.10-2020 Date of Test .............................: 2026-01-09 to 2026-01-14 Test Result...............................: PASS Tested By ................................: (Colin Chen) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: SSP26010103-1E FCC Test Report Page 3 of 23 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Compliance Standards ...........................................................................................................................................7 1.4 Test Facilities ........................................................................................................................................................7 1.5 List of Measurement Instruments ..........................................................................................................................8 1.6 Measurement Uncertainty .....................................................................................................................................8 2. Summary of Test Results .............................................................................................................................................9 3. Antenna Requirement ............................................................................................................................................... 10 3.1 Standard and Limit.............................................................................................................................................. 10 3.2 Test Result .......................................................................................................................................................... 10 4. Conducted Emissions ................................................................................................................................................ 11 4.1 Standard and Limit.............................................................................................................................................. 11 4.2 Test Procedure.................................................................................................................................................... 11 4.3 Test Data and Results .......................................................................................................................................... 12 5. Radiated Emissions ................................................................................................................................................... 15 5.1 Standard and Limit.............................................................................................................................................. 15 5.2 Test Procedure.................................................................................................................................................... 15 5.3 Test Data and Results .......................................................................................................................................... 17 6. Occupied Bandwidth ................................................................................................................................................. 22 6.1 Standard and Limit.............................................................................................................................................. 22 6.2 Test Procedure.................................................................................................................................................... 22 6.3 Test Data and Results ..................................................................…

Text truncated - open the document above for the full version.

Report No: SSP26010103-1E FCC ID: 2BGXO-D2 Annex of Test Report Annex C. Test Photos Conducted Emission Test View 1 Radiated Emission Test View 1 Report No: SSP26010103-1E FCC ID: 2BGXO-D2 Annex of Test Report Radiated Emission Test View 2