2BH2H-C02XOG02000RF SYNC module

July 15th, 2024 Nemko North America, Inc. 303 River Road Ottawa ON K1V 1H2 Canada ATTN.: Reviewing Engineer Subject: FCC Certification - Equipment Not Covered by Prohibition (FCC ID: 2BH2H- C02XOG02000) Applicant: Xtract One Technologies Inc. This letter serves as a certification by Xtract One Technologies ("the Applicant") that the equipment under application for FCC authorization (FCC ID: 2BH2H-C02XOG02000) is not considered "covered" equipment prohibited from receiving authorization under Section §2.903 of the FCC Rules. Verification of non-coverage The Applicant has conducted a thorough review of the current FCC Covered List and confirms that, as of the application filing date, the equipment is not manufactured by any entity identified on the list. Additionally, the Applicant itself is not currently identified on the Covered List as a producer of "covered" equipment. Note: If, in the future, the equipment or the Applicant's status changes in relation to the FCC Covered List, the Applicant will promptly notify the FCC and take all necessary actions to comply with the relevant regulations. Signed: Printed name: Nevine Demitri Title: Director of Innovation Company Name: Xtract One Technologies Inc. Date: July 15 th 2024

U.S. Agent Designation for Service of Process - Certification Attestation Letter August 6, 2024 Nemko North America, Inc. 303 River Road Ottawa ON K1V 1H2 Canada ATTN.: Reviewing Engineer FCC ID: 2BH2H-C02XOG02000 Applicant FRN: 0035754084 This letter serves as a formal designation, pursuant to §2.911(d)(7) of the FCC Rules, of the following U.S. Agent for Service of Process for the equipment under application: U.S. Agent for Service of Process: • Company Name: Xtract One (US) Technologies • Physical U.S. Company Address: 999 18th St Suite 3000, Denver CO 80202 • Agent Name: Nevine Demitri • Agent Email Address: [email protected] • Agent FRN*: N/A *- The agent does not have an FRN because they do no other business with the FCC except for acting as a US agent for service of process, and therefore are not required to have their own FRN. The above listed designated agent hereby acknowledges and accepts the obligation for service of process on behalf of the applicant signed below. The applicant further acknowledges and accepts its obligation to maintain a U.S. Agent for Service of Process for a minimum period of one year following either: • Permanent termination of all marketing and importation activities within the U.S. for the applicable equipment by the grantee. • The conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever occurs later. Applicant/Agent Signed: Signed: Printed name: Nevine Demitri Title: Director of Innovation Company Name: Xtract One (US) Technologies Date: August 6, 2024

Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Appointment of Agent for FCC and ISED Certification Application Dear Director of Certification, This letter formally appoints Spencer Zhong of Nemko Canada, Inc. located at 303 River Road, Ottawa, Ontario, Canada K1V 1H2, as our authorized agent to represent us in the application process for equipment certification. We confirm that the submitted documents accurately depict the device or system seeking certification. Additionally, we guarantee that all units produced, imported, or marketed, as defined by FCC and ISED Canada regulations, will possess a label identical to the one submitted with this application. By signing below, we certify that neither our company nor any party involved in the application is subject to denial of federal benefits, including FCC benefits, as outlined in Section 5301 of the Anti-Drug Abuse Act of 1988 (21 U.S.C. §862) due to a conviction for possession or distribution of a controlled substance. Furthermore, no party involved in the application, as defined in 47 CFR 1.2002 (b), is subject to denial of federal benefits, including FCC benefits. We attest to the truth and accuracy of the information provided to the FCC to the best of our knowledge (47 CFR 2.911 (d)) and acknowledge our responsibilities as a grantee regarding certified equipment (47 CFR 2.909). In instances where our authorized agent signs the application for certification on our behalf, we understand that Nemko North America, Inc. remains solely responsible for adhering to the terms and conditions for certification as specified by Nemko Canada Inc. Sincerely, Dated: July 15th, 2024 Agency agreement expiration date: 7/15/2025 *Up to 12 months Signed by: Nevine Demitri Signature Print name Director of Innovation Title 647-271 0723 Phone On behalf of: Xtract One Technologies Inc. Company name

July 15th, 2024 Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Request for Confidentiality – FCC FCC ID: 2BH2H-C02XOG02000 Pursuant to FCC 47 CFR 0.457(d)(1)(ii) and 0.459 and FCC guidance published in KDB 726920, we hereby request confidential treatment of information accompanying this application as outlined below. We request the exhibits selected below as long term confidential (LTC) be withheld from public view permanently: Selection of exhibits for LTC - general Exhibit name Permanent (Long Term) Block Diagrams Permanent (Long Term) Operation Description / Theory of Operation Permanent (Long Term) Parts List & Placement / BOM Permanent (Long Term) Schematics Selection of exhibits for LTC (with NDA) 3 Exhibit name Permanent (Long Term) User’s Manual Permanent (Long Term) Internal Photos Selection of exhibits for STC Exhibit name Permanent (Long Term) External Photos (180 days) Permanent (Long Term) Test Setup Photos (180 days) Our company has spent a substantial effort in developing this product and it is one of the first of its kind in the industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. When the device is marketed before the requested number of days listed above, the grantee will inform the TCB to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website (if any). The above information contains trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Sincerely, Signed by: Nevine Demitri Signature Print name Director of Innovation Title 647-271 0723 Phone Xtract One Technologies Inc. Company 257 Adelaide St. West, M5H 1X9, Toronto, ON, Canada Address

V2_01.01.2023 Mutual Nondisclosure and Confidentiality Agreement Page1 XTRACT ONE TECHNOLOGIES INC. MUTUAL NONDISCLOSURE AND CONFIDENTIALITY AGREEMENT This Nondisclosure and Confidentiality Agreement (the “Agreement”) made effective on the Effective Date, by and between Xtract One Technologies Inc. (“Xtract One”), with offices at 257 Adelaide Street West, Suite 400, Toronto, ON, M5H 1X9, Canada, and the participant identified below (“Interested Party”): Name of Interested Party Address Contact Individual E-mail Telephone No. Effective Date NOW THEREFORE, IN CONSIDERATION of entering into this Agreement, the mutual covenants, terms and conditions, and agreements herein contained and other good and valuable consideration, the receipt and sufficiency of which are hereby acknowledged, the Parties covenant and agree as follows: 1. Purpose. The Parties wish to disclose to each other certain Confidential Information relating to the other’s business, including without limitation, information relating to threat detection and counter terrorism solutions in relation to concealed weapons and explosives, using radar, microwaves and other electromagnetic fields and radiation, imaging and other audio-visual technologies, cellular and molecular diagnostic technologies, software and database solutions for the sole purpose of assessing the commercial potential of the Technologies by the Parties for a potential business relationship (the “Purpose”), provided that each Recipient maintains the confidentiality of all such information so disclosed at all times or as hereinafter provided by each Discloser. 2. Confidential Information. “Confidential Information” means all information, including data and compilations of data, whether oral or written, in whatever form or medium, including financial, commercial, scientific or technical information received by a Party or any of its Affiliates (the “Recipient”) relating to the discloser or any its Affiliates (the “Discloser”), including without limitation: (a) technical information, trade secrets, inventions, know-how, research, experimental work and results, methods of operation, computer program source codes and object codes, logic diagrams, programming instructions, data and data definitions, computer program architecture, designs, drawings, engineering, hardware configuration information, ideas, specifications, improvements and techniques; (b) product information, product designs, product plans and specifications; (c) business information regarding the Discloser’s customers, vendors and suppliers, business opportunities, ventures, business concepts and strategies, market research; (d) financial information, including costs, sales, income, profits and margins; and/or (e) information that would reasonably be understood, given the nature of the information and the circumstances surrounding its disclosure, to be confidential. “Affiliate” means any entity which, directly or indirectly controls, is controlled by, or is under common control with the subject entity. “Control” (as used in the preceding sentence) means direct or indirect ownership or control of more than fifty percent (50%) of the voting securities or interests of the subject entity. 3. Marking. The Discloser shall identify all Confidential Information to be afforded protection under this Agreement as follows: (a) all documents and other tangible materials shall be marked with an appropriate restrictive legend which indicates the proprietary nature of the material; (b) all other disclosures, including information that is verbally or visually disclosed by the Discloser, must be reduced to written or other permanent form, and shall be identified and marked with an appropriate restrictive legend as being “Confidential” within ten (10) days after such disclosure; V2_01.01.2023 Mutual Nondisclosure and Confidentiality Agreement Page2 (c) information stored in electronic form on disk, tape or other storage medium constitutes information in permanent form. Such electronic Confidential Information will be adequately marked if a proprietary legend is displayed in reasonable proximity to the Confidential Information when it runs on a computer system and when the Confidential Information is displayed or printed from its data file. 4. Exclusion from Confidential Information. Confidential Information shall not include information that: (a) was in the public domain at the time of disclosure; (b) was known and in the possession of the Recipient at the time of the disclosure as can be established by documentary evidence existing prior to the disclosure; (c) was lawfully disclosed to the Recipient by an unrelated third party without restriction on disclosure; (d) was developed by the Recipient without use of the Confidential Information as can be shown by documentary evidence; or (e) disclosure of information which is made subject to an order by judicial or administrative process requiring the Recipient to disclose any or all of the Confidential Information, without restrictions, provided that the Recipient shall use reasonable efforts in the circumstances to promptly notify the Discloser of such requirement to enable the Discloser to participate and oppose such process before disclosure occurs, or seek a protective order. 5. Disclosure Obligations. The Recipient shall: (a) hold the Confidential Information in strict confidence and take reasonable precautions to protect such Confidential Information (such precautions to include, at a minimum, all precautions the Recipient employs with respect to its own confidential information); (b) not copy, divulge, furnish, disclose or make accessible to any person, firm, organization or corporation (other than its employees or contractors who need to know), any aspect or portion of the Confidential Information; (c) not reverse engineer, decompile or disassemble any product (hardware or software) received from - 2 - the Discloser except as authorized; and (d) not use any Confidential I…

Text truncated - open the document above for the full version.

July 15 th , 2024. Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Request for Limited Modular Approval FCC ID: 2BH2H-C02XOG02000 The following attestation addresses the requirements to support modular approval: Modular approval requirement Yes (provide brief statement) No * (1) The radio elements must have its own radio frequency circuitry shielded. The physical crystal and tuning capacitor(s) may be located external to the shield, but must be on the module assembly The module contains a metal shield which covers all RF components and circuitry. The shield is located on the top of the board next to antenna connector – (2) The module must have buffered modulation/data inputs (if provided) to ensure that the device will comply with FCC requirements under conditions of excessive data rates or over-modulation. Data to the modulation circuit is buffered as described in the operational description provided with the application. – (3) The module must contain its own power supply regulation on the module. This is intended to ensure that the module will comply with FCC requirements regardless of the design of the power supplying circuitry in the device into which the module is installed. -- The module accepts power from an externally regulated power supply unit. It receives 3.3Volts DC. (4) The module must comply with the antenna and transmission system requirements of §§ 15.203, 15.204(b), 15.204(c), 15.212(a), and 2.929(b). The antenna must either be permanently attached or employ a ‘‘unique’’ antenna coupler (at all connections between the module and the antenna, including the cable). The ‘‘professional installation’’ provision of § 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph 15.212(b). 15.212(a)(1)(iv) The module connects to its antenna using a standard SMA style connector. A list of antennas tested and approved with this device may be found in user’s manual provided with the application. – (5) The module must demonstrate compliance in a stand-alone configuration, the module must not be inside another device during testing. This is intended to demonstrate that the module can comply with Part 15 emission limits regardless of the device into which it is eventually installed. – The module was tested within a representative host (XtractOne Gateway, model: S00-XOG- 02000) as shown in test setup photographs filed with this application (6) The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements) -- The module is too small to have a label printed on it. The FCC ID is printed in the user manual and battery case of the host product. (7) The module must comply with all specific rule or operating requirements applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. A copy of these instructions must be included in the application for equipment authorization. Example: The module complies with FCC Part 15C requirements. Instructions to the OEM installer are provided in the installation manual filed with this application – (8) The module must comply with any applicable RF exposure requirements The module meets Portable exclusion levels as shown in the RF exposure information filed with this application. – FCC Class II Permissive Change filing by the grantee (Xtract One) is required for each new host configuration. Sincerely, Signed by: Nevine Demitri Signature Print name Director of Innovation Title 647-271 0723 Phone

MANUFACTURER: XTRACT ONE TECHNOLOGIES INC. PRODUCT TYPE: XTRACT ONE GATEWAY MODEL NUMBER: S00-XOG-02000 SERIAL NUMBER: XXXXX-YYYYY CANADA CONTACT ADDRESS: 257 Adelaide St W, Suite 400, Toronto, ON M5H 1X9 905-333-4141 MANUFACTURER COUNTRY OF ORIGIN: CANADA (CONTAINS RF MODULE) FCC ID: 2BH2H-C02XOG02000 IC: 32822-C02XOG02000 Module HVIN: C02-XOG-0200 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and, (2) this device must accept any interference received, including interference that may cause undesired operation. — COO-MSG-01023 100-120VAC ~ 50/60Hz 1.5A 200-240VAC ~ 50/60Hz 0.75A xtractone.com

MANUFACTURER: XTRACT ONE INC. PRODUCT TYPE: AI-SECURITY GATEWAY MODEL NUMBER: S00-XOG-02000 SERIAL NUMBER: XXXXX-YYYYY CANADA CONTACT ADDRESS: 257 Adelaide St W, Suite 400, Toronto, ON M5H 1X9 905-333-4141 MANUFACTURER COUNTRY OF ORIGIN: CANADA (CONTAINS RF MODULE) FCC ID: 2BH2H-C02XOG02000 IC: 32822-C02XOG02000 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and, (2) this device must accept any interference received, including interference that may cause undesired operation.

Sept 10th, 2024 Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Request for No Label on Unit – FCC FCC ID: 2BH2H-C02XOG02000 We request the approval for the label on the radio device in question, to not be placed on the physical device. Reason: We want to ensure that the thermal specifications within the enclosed case are met. We must avoid damaging any affixed labels or electronic circuitry. Additionally, we need to prevent any physical labels from being placed in positions where they could peel off or hinder thermal convection in our final product. The product is an LMA and will be installed within the host. To avoid damaging the module, it will not have its own label, instead, the FCC ID will be printed on the host label and included in the User Manual. Sincerely, Signed by: Nevine Demitri Signature Print name Director of Innovation Title 647-271 0723 Phone Xtract One Technologies Inc. Company 257 Adelaide St. West, M5H 1X9, Toronto, ON, Canada Address

www.nemko.com Nemko Canada Inc., a testing laboratory, is accredited by ANSI National Accreditation Board (ANAB). The tests included in this report are within the scope of this accreditation. The ANAB symbol is an official symbol of the ANSI National Accreditation Board, used under licence. ANAB File Number: AT-3195 (Ottawa); AT-3193 (Pointe-Claire); AT-3194 (Cambridge) FCC and ISED MPE Calculation; Date: July 2024 C h o o s e S c a n d i n a v i a n t r u s t RADIO TEST REPORT Report ID Project ID REP057150 PRJ0061410 Type of assessment: MPE Calculation report Manufacturer: Description of product: Xtract One Technologies Inc RF SYNC module Product Marketing Name (PMN): Model/HVIN: X1-SYNC C02-XOG-02000 FCC identifier: ISED certification number: FCC ID: 2BH2H-C02XOG02000 IC: 32822-C02XOG02000 Specification:  FCC 47 CFR Part 1 Subpart I, §1.1307, §1.1310  FCC 47 CFR Part 2 Subpart J, §2.1091  FCC KDB 447498 D01 General RF Exposure Guidance v06  ISED Canada RSS-102 Issue 6 (December 2023) RSS-102 Annex A ATTESTATION: I attest that the information provided in Annex A is correct; that the Technical Brief was prepared and the information contained therein is correct; that the device evaluation was performed or supervised by me; that applicable measurement methods and evaluation methodologies have been followed; and that the device meets the applicable RF exposure limits set forth in RSS-102. Date of issue: August 29, 2024 Fahar Abdul Sukkoor, EMC/RF Specialist Prepared by Signature Report reference ID: REP057150 Page 2 of 7 Lab locations Company name Nemko Canada Inc. Facilities Ottawa site: 303 River Road Ottawa, Ontario Canada K1V 1H2 Tel: +1 613 737 9680 Fax: +1 613 737 9691 Montréal site: 292 Labrosse Avenue Pointe-Claire, Québec Canada H9R 5L8 Tel: +1 514 694 2684 Fax: +1 514 694 3528 Cambridge site: 1-130 Saltsman Drive Cambridge, Ontario Canada N3E 0B2 Tel: +1 519 650 4811 Test site registration Organization Ottawa Montreal Cambridge FCC: CA2040 CA2041 CA0101 ISED: 2040A-4 2040G-5 24676 Website www.nemko.com Limits of responsibility Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. All results contained in this report are within Nemko Canada’s ISO/IEC 17025 accreditation. Copyright notification Nemko Canada Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. © Nemko Canada Inc. Report reference ID: REP057150 Page 3 of 7 Table of Contents Table of Contents ......................................................................................................................................................................................................... 3 Evaluation summary ........................................................................................................................................................................... 4 1.1 MPE calculation for standalone transmission ........................................................................................................................................................... 4 1.2 RSS-102, Annex A – RF technical brief cover sheet ................................................................................................................................................... 7 Section 1.1 MPE calculation for standalone transmission Report reference ID: REP057150 Page 4 of 7 Evaluation summary 1.1 MPE calculation for standalone transmission 1.1.1 References, definitions and limits FCC §2.1091(d) (2) For operations within the frequency range of 300 kHz and 6 GHz (inclusive), the limits for maximum permissible exposure (MPE), derived from whole-body SAR limits and listed in Table 1 in paragraph (e)(1) of this section, may be used instead of whole-body SAR limits as set forth in paragraphs (a) through (c) of this section to evaluate the environmental impact of human exposure to RF radiation as specified in §1.1307(b) of this part, except for portable devices as defined in §2.1093 of this chapter as these evaluations shall be performed according to the SAR provisions in §2.1093. Table 1.1-1: Table 1 to §1.1310(e)(1) — Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (i) Limits for Occupational/Controlled Exposure 0.3–3.0 614 1.63 *(100) ≤6 3.0–30 1842 / f 4.89 / f *(900 / f 2 ) <6 30–300 61.4 0.163 1.0 <6 300–1500 – – f / 300 <6 1500–100000 – – 5 <6 (ii) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) <30 1.34–30 824 / f 2.19 / f *(180 / f 2 ) <30 30–300 27.5 0.073 0.2 <30 300–1500 – – f / 1500 <30 1500–100000 – – 1.0 <30 Notes: f = frequency in MHz, * = Plane-wave equivalent power density. Section 1.1 MPE calculation for standalone transmission Report reference ID: REP057150 Page 5 of 7 References, definitions and limits, continued RSS-102, Section 5.1 Through this standard, ISED adopts Health Canada’s RF exposure guideline entitled Limits of Human Exposure to Radiofrequency Electromagnetic Energy in the Frequency Range from 3 kHz to 300 GHz (Safety Code 6) and its Notice: Localized human exposure limits for radiofrequency fields in the range of 6 GHz to 300 GHz. Table 1.1-2: Table 7&8 to RSS-102 — RF Field Strength and power density Limits Frequency range (MHz) Electric field strength (V/m rms) Magnetic field strength (A/m rms) Power densi…

Text truncated - open the document above for the full version.

www.nemko.com Nemko Canada Inc., a testing laboratory, is accredited by ANSI National Accreditation Board (ANAB). The tests included in this report are within the scope of this accreditation. The ANAB symbol is an official symbol of the ANSI National Accreditation Board, used under licence. ANAB File Number: AT-3195 (Ottawa); AT-3193 (Pointe-Claire); AT-3194 (Cambridge) FCC 15.247 and RSS-247; Date: Feb 12, 2024 C h o o s e S c a n d i n a v i a n t r u s t RADIO TEST REPORT Report ID: Project number: REP051835 PRJ0061410 Type of assessment: Original testing, Limited Modular Approval Type of radio equipment: Spread Spectrum/Digital Device (902–928 MHz) Equipment class: DSS Applicant: Description of product: Xtract One Technologies Inc RF SYNC module Model/HVIN: Product marketing name (PMN): C02-XOG-02000 X1-SYNC FCC identifier: ISED certification number: FCC ID: 2BH2H-C02XOG02000 IC: 32822-C02XOG02000 Specifications:  FCC 47 CFR Part 15 Subpart C, §15.247  RSS-247, Issue 3, August 2023, Section 5 Date of issue: August 29, 2024 Fahar Abdul Sukkoor, EMC/RF Specialist Tested by Signature Kevin Rose, EMC/RF Specialist Reviewed by Signature Report reference ID: REP051835 Page 2 of 40 Lab locations Company name Nemko Canada Inc. Facilities Ottawa site: 303 River Road Ottawa, Ontario Canada K1V 1H2 Tel: +1 613 737 9680 Fax: +1 613 737 9691 Montréal site: 292 Labrosse Avenue Pointe-Claire, Québec Canada H9R 5L8 Tel: +1 514 694 2684 Fax: +1 514 694 3528 Cambridge site: 1-130 Saltsman Drive Cambridge, Ontario Canada N3E 0B2 Tel: +1 519 650 4811 Test site identifier Organization Ottawa Montreal Cambridge FCC: CA2040 CA2041 CA0101 ISED: 2040A-4 2040G-5 24676 Website www.nemko.com Limits of responsibility Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. All results contained in this report are within Nemko Canada’s ISO/IEC 17025 accreditation. Copyright notification Nemko Canada Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. © Nemko Canada Inc. Report reference ID: REP051835 Page 3 of 40 Table of Contents Table of Contents ......................................................................................................................................................................................................... 3 Report summary ................................................................................................................................................................................. 4 1.1 Test specifications .................................................................................................................................................................................................... 4 1.2 Test methods ............................................................................................................................................................................................................ 4 1.3 Exclusions ................................................................................................................................................................................................................. 4 1.4 Statement of compliance .......................................................................................................................................................................................... 4 1.5 Test report revision history ....................................................................................................................................................................................... 4 Engineering considerations ................................................................................................................................................................. 5 2.1 Modifications incorporated in the EUT for compliance ............................................................................................................................................ 5 2.2 Technical judgment .................................................................................................................................................................................................. 5 2.3 Model variant declaration ........................................................................................................................................................................................ 5 2.4 Deviations from laboratory tests procedures .........................…

Text truncated - open the document above for the full version.