2BH7FBE670BE12000 Tri-Band Wi-Fi 7 Router

© 2022 TP-Link 1910013306 REV1.0.1 User Guide BE12000 Tri-Band Wi-Fi 7 Router Model Archer BE670/Archer BE12000 121 FCC compliance information statement Product Name: BE12000 Tri-Band Wi-Fi 7 Router Model Number:Archer BE670/Archer BE12000 Component NameModel I.T.E. Power Supply T120330-2B4 Responsible party: TP-Link Systems Inc. Address: 10 Mauchly, Irvine, CA 92618 Website: http://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6804 E-mail: [email protected] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the s eparation between the equipment and receiver. • Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is connected. •Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device ma y not cause harmful interference. 2. This device must ac cept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 122 Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 23 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” • FCC regulations restrict the operation of this device to indoor use only. • The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in the 5.925–6.425 GHz bands in large aircraft while flying above 10,000 feet.. • Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems. FCC compliance information statement Product Name: I.T.E. Power Supply Model Number: T120330-2B4 Responsible party: TP-Link Systems Inc. Address: 10 Mauchly, Irvine, CA 92618 Website: http://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6804 E-mail: [email protected] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 123 •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. W e, TP-Link Systems Inc., has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated. Issue Date: 2025-11-07

Quick Installation Guide Tri-Band Wi-Fi 7 Router With the USB port, it’s easy to share files and media with multiple devices. Visit https://www.tp-link.com/app/usb to learn more about the USB applications. USB Applications Media Server: Play media from the USB drive on your computer Local Storage Sharing: 6KDUHƮOHVIURPWKH86%GULYH ZLWKGHYLFHVRQ\RXUKRPHQHWZRUN Remote Access: $FFHVVWKH86%GULYHZKHQ\RXDUH away from home You can experience strong, stable, and seamless wireless connections throughout your home with EasyMesh. EasyMesh-Compatible Flexible Scalability )OH[LEO\VFDOH\RXUKRPHQHWZRUNLQJZLWKGLƬHUHQW YHQGRUV GLƬHUHQWWRSRORJLHVGLƬHUHQW3URWRFROV DQGGLƬHUHQWSURGXFWFDWHJRULHV One-Click Settings 3UHVVWKH:36EXWWRQRQWKHPDLQURXWHUDQGWKH VDWHOOLWHGHYLFHZLWKLQPLQXWHVRIHDFKRWKHUWKHQ WKH(DV\0HVKQHWZRUNZLOOVHWXS Seamless Roaming &RQQHFWVPRELOHGHYLFHVWR\RXUURXWHUVRU H[WHQGHUVWKDWSURYLGHWKHEHVWFRYHUDJH'HYLFHV FRPSDWLEOHZLWK(DV\0HVKDOVRVKDUHDVLQJOH :L)LQDPHVR\RXVWD\FRQQHFWHGLQHYHU\URRP  For more information, visit https://www.tp-link.com/easymesh/ )DLOXUHPD\EHGXHWRƮUPZDUHFRQưLFWVRIGLƬHUHQWYHQGRUV$EHWWHU QHWZRUNFRQQHFWLRQFDQEHHVWDEOLVKHGEHWZHHQDOO$3VIURP73/LQN Setup Video Q1. What should I do if I want to change the WAN/LAN port for internet service? r&RQQHFWWR\RXUGHVLUHG:$1/$1SRUWZLWKDQ(WKHUQHWFDEOH 'XULQJWKHTXLFNQHWZRUNVHWXSVHOHFWWKHFRUUHVSRQGLQJSRUW DVWKHLQWHUQHWSRUW$OWHUQDWLYHO\JRWRMore > Internet Connection > Internet Port 7HWKHUDSS RUAdvanced > Network Internet > Internet Port ZHEPDQDJHPHQWSDJH WR FKDQJHWKHLQWHUQHWSRUW Q2. What should I do if I can’t access the web management page? • 5HERRW\RXUURXWHUDQGWU\DJDLQ • ,IWKHFRPSXWHULVVHWWRDVWDWLF,3FKDQJHLWVVHWWLQJVWRREWDLQ DQ,3DGGUHVVDXWRPDWLFDOO\ • Verify that http://tplinkwifi.netLVFRUUHFWO\HQWHUHGLQWKHZHE EURZVHU$OWHUQDWLYHO\HQWHUhttp://192.168.0.1 or http://192.168.1.1LQWKHZHEEURZVHU • 8VHDQRWKHUZHEEURZVHUDQGWU\DJDLQ • 'LVDEOHDQGHQDEOHWKHQHWZRUNDGDSWHULQXVH Q3. What should I do if I can’t access the internet? • 3RZHURII\RXUPRGHPIRUDERXWPLQXWHVWKHQSRZHULWRQ DQGFKHFNWKHLQWHUQHW,I\RXUPRGHPKDVPRUHWKDQRQH (WKHUQHWSRUWNHHSWKHRWKHUSRUWVXQFRQQHFWHG • &KHFNLIWKHLQWHUQHWLVZRUNLQJQRUPDOO\E\FRQQHFWLQJD FRPSXWHUGLUHFWO\WRWKHPRGHPYLDDQ(WKHUQHWFDEOH,ILWLV QRWFRQWDFW\RXULQWHUQHWVHUYLFHSURYLGHU • /RJLQWRWKHZHEPDQDJHPHQWSDJHDQGJRWRWKHNetwork Map SDJHWRFKHFNZKHWKHUWKHLQWHUQHW,3DGGUHVVLVYDOLGRUQRW,I LWoVYDOLGJRWRAdvanced > Network > Internet > InternetFOLFN Advanced SettingsVHOHFWUse the Following DNS Addresses VHWWKHSULPDU\'16WRDQGVHWWKHVHFRQGDU\'16WR ,ILWLVQRWFKHFNWKHKDUGZDUHFRQQHFWLRQRUFRQWDFW \RXULQWHUQHWVHUYLFHSURYLGHU • )RUFDEOHPRGHPXVHUVORJLQWRWKHZHEPDQDJHPHQWSDJHRI WKHURXWHUDQGJRWRAdvanced > Network > Internet > MAC Need Help? †73/LQN5(9 Clone6HOHFWClone Current Device MACDQGFOLFNSAVE7KHQ UHERRWERWKWKHPRGHPDQGWKHURXWHU Q4. What should I do if I forget my wireless password? • ,I\RXKDYHQRWFKDQJHGWKHGHIDXOWZLUHOHVVSDVVZRUGLWFDQEH IRXQGRQWKHODEHODWWKHERWWRPRIWKHURXWHU • &RQQHFWDFRPSXWHUGLUHFWO\WRWKHURXWHUXVLQJDQ(WKHUQHW FDEOH/RJLQWRWKHURXWHUoVZHEPDQDJHPHQWSDJHDW KWWSWSOLQNZLƮQHWDQGJRWRWKHWirelessSDJHWRUHWULHYHRU UHVHW\RXUZLUHOHVVSDVVZRUG  Q5. How should I position my router for optimal Wi-Fi performance? r'RQoWSODFH\RXUURXWHULQDFRUQHURULQDFORVHW r$YRLGREVWDFOHVDQGKLJKSRZHUHGDSSOLDQFHV r.HHS\RXUURXWHULQDFHQWUDOORFDWLRQDWDFHUWDLQKHLJKW r.HHSWKHDQWHQQDVYHUWLFDOZKHQWKHURXWHULVSODFHGRQD GHVNWRS.HHSWKHDQWHQQDVXSULJKWZKHQWKHURXWHULV KDQJLQJRQDZDOO ”.HHSWKHGHYLFHDZD\IURPZDWHUƮUHKXPLGLW\RUKRWHQYLURQPHQWV ”'RQRWDWWHPSWWRGLVDVVHPEOHUHSDLURUPRGLI\WKHGHYLFH,I\RXQHHGVHUYLFH SOHDVHFRQWDFWXV ”'RQRWXVHDQ\RWKHUFKDUJHUVWKDQWKRVHUHFRPPHQGHG ”'RQRWXVHGDPDJHGFKDUJHURU86%FDEOHWRFKDUJHWKHGHYLFH ”'RQRWXVHWKHGHYLFHZKHUHZLUHOHVVGHYLFHVDUHQRWDOORZHG ”$GDSWHUVKDOOEHLQVWDOOHGQHDUWKHHTXLSPHQWDQGVKDOOEHHDVLO\DFFHVVLEOH 73/LQNKHUHE\GHFODUHVWKDWWKH7UL%DQG:L)L5RXWHULVLn compliance with the HVVHQWLDOUHTXLUHPHQWVDQGRWKHUUHOHYDQWSURYLVLRQVRIGLUHFWLYHV(8 (&(8DQG (8  7KHRULJLQDO(8GHFODUDWLRQRIFRQIRUPLW\PD\EHIRXQGDW KWWSVZZZWSOLQNFRPHQVXSSRUWFH 73/LQNKHUHE\GHFODUHVWKDWWKH7UL%DQG:L)L5RXWHULVLQFRPSOLDQFHZLWKWKH HVVHQWLDOUHTXLUHPHQWVDQGRWKHUUHOHYDQWSURYLVLRQVRIWKH5DGLR(TXLSPHQW 5HJXODWLRQV 7KHRULJLQDO8.GHFODUDWLRQRIFRQIRUPLW\PD\EHIRXQGDW KWWSVZZZWSOLQNFRPVXSSRUWXNFD TP-Link HomeShield premium security services keep your home network safe with cutting-edge features. Download the Tether app to enjoy HomeShield features. For more details, visit https://www.tp-link.com/homeshield. Parental Controls 0DQDJHRQOLQHWLPHDQG EORFNLQDSSURSULDWHFRQWHQW to maintain healthy online KDELWV Comprehensive Reports *DLQIXOOVWDWLVWLFVDQG LQVLJKWVWRKHOS\RXNQRZ \RXUKRPHQHWZRUNEHWWHU Network Protection 'HWHFWVF\EHUWKUHDWVWR NHHS\RXUSULYDF\DQG FRQQHFWHGGHYLFHVZHOO SURWHFWHG Quality of Service (QoS) Prioritize your bandwidth QHHGVIRUDEHWWHU QHWZRUNLQJH[SHULHQFH 7HWKHU TP-Link HomeShield )RUWHFKQLFDOVXSSRUWUHSODFHPHQWVHUYLFHVXVHUJXLGHVDQG RWKHULQIRUPDWLRQSOHDVHYLVLWhttps://www.tp-link.com/support Method ONE: Via the TP-Link Tether AppMethod TWO: Via a Web Browser 1. Connect your device to the router wirelessly or with an Ethernet cable. New Password: Let’s Get Started &RQƮUP3DVVZRUG KWWSWSOLQNZLƮQHW 2. Launch a web b…

Text truncated - open the document above for the full version.

Project No.: 2508C300 Page 6 of 11 6G_Ant.1 6G_Ant.2 5G_Ant.1 5G_Ant.4 & 2.4G Ant.2 5G_Ant.2 5G_Ant.3 & 2.4G Ant.1 Project No.: 2508C300 Page 7 of 11 Project No.: 2508C300 Page 8 of 11 Project No.: 2508C300 Page 9 of 11 Project No.: 2508C300 Page 10 of 11 Project No.: 2508C300 Page 11 of 11

Report No.: BTL-FCCP-1-2508C300 Report Version: R00 Page 32 of 145 11. EUT TEST PHOTO AC Power Line Conducted Emissions Test Photos Report No.: BTL-FCCP-1-2508C300 Report Version: R00 Page 33 of 145 Radiated Emissions Test Photos 9 kHz to 30 MHz Report No.: BTL-FCCP-1-2508C300 Report Version: R00 Page 34 of 145 Radiated Emissions Test Photos 30 MHz to 1 GHz Report No.: BTL-FCCP-1-2508C300 Report Version: R00 Page 35 of 145 Radiated Emissions Test Photos Band edge & Harmonic(1 GHz to 18 GHz) Report No.: BTL-FCCP-1-2508C300 Report Version: R00 Page 36 of 145 Radiated Emissions Test Photos Harmonic(18 GHz to 26.5 GHz) Report No.: BTL-FCCP-1-2508C300 Report Version: R00 Page 37 of 145 Conducted Test Photos

Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 133 of 145 Test Mode TX N(HT40) Mode_Ant. 1 Reference Level-CH03 Reference Level-CH06 Reference Level-CH09 Bandedge-CH03 Bandedge-CH09 Harmonic-CH03 Harmonic-CH06 Harmonic-CH09 Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 134 of 145 Test Mode TX N(HT40) Mode_Ant. 2 Reference Level-CH03 Reference Level-CH06 Reference Level-CH09 Bandedge-CH03 Bandedge-CH09 Harmonic-CH03 Harmonic-CH06 Harmonic-CH09 Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 135 of 145 Test Mode TX BE(EHT20) Mode_Ant. 1 Reference Level-CH01 Reference Level-CH06 Reference Level-CH11 Bandedge-CH01 Bandedge-CH11 Harmonic-CH01 Harmonic-CH06 Harmonic-CH11 Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 136 of 145 Test Mode TX BE(EHT20) Mode_Ant. 2 Reference Level-CH01 Reference Level-CH06 Reference Level-CH11 Bandedge-CH01 Bandedge-CH11 Harmonic-CH01 Harmonic-CH06 Harmonic-CH11 Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 137 of 145 Test Mode TX BE(EHT40) Mode_Ant. 1 Reference Level-CH03 Reference Level-CH06 Reference Level-CH09 Bandedge-CH03 Bandedge-CH09 Harmonic-CH03 Harmonic-CH06 Harmonic-CH09 Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 138 of 145 Test Mode TX BE(EHT40) Mode_Ant. 2 Reference Level-CH03 Reference Level-CH06 Reference Level-CH09 Bandedge-CH03 Bandedge-CH09 Harmonic-CH03 Harmonic-CH06 Harmonic-CH09 Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 139 of 145 APPENDIX H - POWER SPECTRAL DENSITY Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 140 of 145 Test Mode TX B Mode_Ant. 1 Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 01 2412 3.91 7.03 Pass 06 2437 3.83 7.03 Pass 11 2462 4.27 7.03 Pass CH01 CH06 CH11 Test Mode TX B Mode_Ant. 2 Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 01 2412 3.62 7.03 Pass 06 2437 3.44 7.03 Pass 11 2462 3.47 7.03 Pass CH01 CH06 CH11 Test Mode TX B Mode_Total Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 01 2412 6.78 7.03 Pass 06 2437 6.65 7.03 Pass 11 2462 6.89 7.03 Pass Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 141 of 145 Test Mode TX G Mode_Ant. 1 Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 01 2412 1.17 7.03 Pass 06 2437 1.78 7.03 Pass 11 2462 1.50 7.03 Pass CH01 CH06 CH11 Test Mode TX G Mode_Ant. 2 Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 01 2412 0.35 7.03 Pass 06 2437 1.13 7.03 Pass 11 2462 0.27 7.03 Pass CH01 CH06 CH11 Test Mode TX G Mode_Total Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 01 2412 3.79 7.03 Pass 06 2437 4.47 7.03 Pass 11 2462 3.94 7.03 Pass Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 142 of 145 Test Mode TX N(HT20) Mode_Ant. 1 Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 01 2412 0.92 7.03 Pass 06 2437 0.87 7.03 Pass 11 2462 0.93 7.03 Pass CH01 CH06 CH11 Test Mode TX N(HT20) Mode_Ant. 2 Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 01 2412 0.11 7.03 Pass 06 2437 0.65 7.03 Pass 11 2462 0.85 7.03 Pass CH01 CH06 CH11 Te s t Mode TX N(HT20) Mode_Total Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 01 2412 3.54 7.03 Pass 06 2437 3.77 7.03 Pass 11 2462 3.90 7.03 Pass Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 143 of 145 Test Mode TX N(HT40) Mode_Ant. 1 Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 03 2422 -1.54 7.03 Pass 06 2437 0.17 7.03 Pass 09 2452 -0.76 7.03 Pass CH03 CH06 CH09 Test Mode TX N(HT40) Mode_Ant. 2 Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 03 2422 -0.79 7.03 Pass 06 2437 -1.57 7.03 Pass 09 2452 -1.57 7.03 Pass CH03 CH06 CH09 Test Mode TX N(HT40) Mode_Total Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 03 2422 1.86 7.03 Pass 06 2437 2.40 7.03 Pass 09 2452 1.86 7.03 Pass Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 144 of 145 Test Mode TX BE(EHT20) Mode_Ant. 1 Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 01 2412 0.19 7.03 Pass 06 2437 -0.50 7.03 Pass 11 2462 0.27 7.03 Pass CH01 CH06 CH11 Test Mode TX BE(EHT20) Mode_Ant. 2 Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 01 2412 -0.80 7.03 Pass 06 2437 -0.83 7.03 Pass 11 2462 -0.02 7.03 Pass CH01 CH06 CH11 Test Mode TX BE(EHT20) Mode_Total Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 01 2412 2.73 7.03 Pass 06 2437 2.35 7.03 Pass 11 2462 3.14 7.03 Pass Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 145 of 145 Test Mode TX BE(EHT40) Mode_Ant. 1 Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 03 2422 -2.21 7.03 Pass 06 2437 -4.17 7.03 Pass 09 2452 -2.59 7.03 Pass CH03 CH06 CH09 Test Mode TX BE(EHT40) Mode_Ant. 2 Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 03 2422 -3.00 7.03 Pass 06 2437 -3.98 7.03 Pass 09 2452 -3.69 7.03 Pass CH03 CH06 CH09 Test Mode TX BE(EHT40) Mode_Total Channel Frequency (MHz) Power Spectral Density (dBm/3kHz) Max. Limit (dBm/3kHz) Result 03 2422 0.42 7.03 Pass 06 2437 -1.06 7.03 Pass 09 2452 -0.10 7.03 Pass End of Test Report

Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 114 of 145 Test Mode TX G Mode Channel Frequency (MHz) 6 dB Bandwidth (MHz) 99 % Occupied Bandwidth (MHz) 6 dB Bandwidth Min. Limit (MHz) Result 01 2412 16.400 17.443 0.5 Pass 06 2437 16.400 17.450 0.5 Pass 11 2462 16.360 17.497 0.5 Pass CH01 CH06 CH11 6 dB Bandwidth 99 % Occupied Bandwidth Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 115 of 145 Test Mode TX N(HT20) Mode Channel Frequency (MHz) 6 dB Bandwidth (MHz) 99 % Occupied Bandwidth (MHz) 6 dB Bandwidth Min. Limit (MHz) Result 01 2412 17.600 18.179 0.5 Pass 06 2437 17.600 18.403 0.5 Pass 11 2462 17.600 18.226 0.5 Pass CH01 CH06 CH11 6 dB Bandwidth 99 % Occupied Bandwidth Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 116 of 145 Test Mode TX N(HT40) Mode Channel Frequency (MHz) 6 dB Bandwidth (MHz) 99 % Occupied Bandwidth (MHz) 6 dB Bandwidth Min. Limit (MHz) Result 03 2422 36.320 36.858 0.5 Pass 06 2437 36.320 37.329 0.5 Pass 09 2452 36.320 36.945 0.5 Pass CH03 CH06 CH09 6 dB Bandwidth 99 % Occupied Bandwidth Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 117 of 145 Test Mode TX BE(EHT20) Mode Channel Frequency (MHz) 6 dB Bandwidth (MHz) 99 % Occupied Bandwidth (MHz) 6 dB Bandwidth Min. Limit (MHz) Result 01 2412 18.920 19.271 0.5 Pass 06 2437 18.960 19.356 0.5 Pass 11 2462 18.920 19.273 0.5 Pass CH01 CH06 CH11 6 dB Bandwidth 99 % Occupied Bandwidth Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 118 of 145 Test Mode TX BE(EHT40) Mode Channel Frequency (MHz) 6 dB Bandwidth (MHz) 99 % Occupied Bandwidth (MHz) 6 dB Bandwidth Min. Limit (MHz) Result 03 2422 37.760 38.115 0.5 Pass 06 2437 37.760 38.211 0.5 Pass 09 2452 37.760 38.165 0.5 Pass CH03 CH06 CH09 6 dB Bandwidth 99 % Occupied Bandwidth Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 119 of 145 APPENDIX F - MAXIMUM OUTPUT POWER Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 120 of 145 Test Mode TX B Mode_Ant 1 Channel Frequency (MHz) Output Power (dBm) Duty Factor (dB) Output Power + Duty Factor (dBm) Max. Limit (dBm) Max. Limit (W) Result 01 2412 23.12 0.23 23.35 30.00 1.0000 Pass 06 2437 22.94 0.23 23.17 30.00 1.0000 Pass 11 2462 22.17 0.23 22.40 30.00 1.0000 Pass Test Mode TX B Mode_Ant 2 Channel Frequency (MHz) Output Power (dBm) Duty Factor (dB) Output Power + Duty Factor (dBm) Max. Limit (dBm) Max. Limit (W) Result 01 2412 22.79 0.23 23.02 30.00 1.0000 Pass 06 2437 23.07 0.23 23.30 30.00 1.0000 Pass 11 2462 22.54 0.23 22.77 30.00 1.0000 Pass Test Mode TX B Mode_Total Channel Frequency (MHz) Output Power (dBm) Max. Limit (dBm) Max. Limit (W) Result 01 2412 26.20 30.00 1.0000 Pass 06 2437 26.25 30.00 1.0000 Pass 11 2462 25.60 30.00 1.0000 Pass Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 121 of 145 Test Mode TX G Mode_Ant 1 Channel Frequency (MHz) Output Power (dBm) Duty Factor (dB) Output Power + Duty Factor (dBm) Max. Limit (dBm) Max. Limit (W) Result 01 2412 20.18 0.24 20.42 30.00 1.0000 Pass 06 2437 22.31 0.24 22.55 30.00 1.0000 Pass 11 2462 20.96 0.24 21.20 30.00 1.0000 Pass Test Mode TX G Mode_Ant 2 Channel Frequency (MHz) Output Power (dBm) Duty Factor (dB) Output Power + Duty Factor (dBm) Max. Limit (dBm) Max. Limit (W) Result 01 2412 19.20 0.24 19.44 30.00 1.0000 Pass 06 2437 22.47 0.24 22.71 30.00 1.0000 Pass 11 2462 20.77 0.24 21.01 30.00 1.0000 Pass Test Mode TX G Mode_Total Channel Frequency (MHz) Output Power (dBm) Max. Limit (dBm) Max. Limit (W) Result 01 2412 22.97 30.00 1.0000 Pass 06 2437 25.64 30.00 1.0000 Pass 11 2462 24.11 30.00 1.0000 Pass Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 122 of 145 Test Mode TX N(HT20) Mode_Ant 1 Channel Frequency (MHz) Output Power (dBm) Duty Factor (dB) Output Power + Duty Factor (dBm) Max. Limit (dBm) Max. Limit (W) Result 01 2412 18.61 0.24 18.85 30.00 1.0000 Pass 06 2437 22.18 0.24 22.42 30.00 1.0000 Pass 11 2462 20.05 0.24 20.29 30.00 1.0000 Pass Test Mode TX N(HT20) Mode_Ant 2 Channel Frequency (MHz) Output Power (dBm) Duty Factor (dB) Output Power + Duty Factor (dBm) Max. Limit (dBm) Max. Limit (W) Result 01 2412 18.64 0.24 18.88 30.00 1.0000 Pass 06 2437 22.36 0.24 22.60 30.00 1.0000 Pass 11 2462 19.95 0.24 20.19 30.00 1.0000 Pass Test Mode TX N(HT20) Mode_Total Channel Frequency (MHz) Output Power (dBm) Max. Limit (dBm) Max. Limit (W) Result 01 2412 21.87 30.00 1.0000 Pass 06 2437 25.52 30.00 1.0000 Pass 11 2462 23.25 30.00 1.0000 Pass Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 123 of 145 Test Mode TX N(HT40) Mode_Ant 1 Channel Frequency (MHz) Output Power (dBm) Duty Factor (dB) Output Power + Duty Factor (dBm) Max. Limit (dBm) Max. Limit (W) Result 03 2422 17.27 0.46 17.73 30.00 1.0000 Pass 06 2437 18.65 0.46 19.11 30.00 1.0000 Pass 09 2452 18.53 0.46 18.99 30.00 1.0000 Pass Test Mode TX N(HT40) Mode_Ant 2 Channel Frequency (MHz) Output Power (dBm) Duty Factor (dB) Output Power + Duty Factor (dBm) Max. Limit (dBm) Max. Limit (W) Result 03 2422 17.17 0.46 17.63 30.00 1.0000 Pass 06 2437 18.71 0.46 19.17 30.00 1.0000 Pass 09 2452 18.56 0.46 19.02 30.00 1.0000 Pass Test Mode TX N(HT40) Mode_Total Channel Frequency (MHz) Output Power (dBm) Max. Limit (dBm) Max. Limit (W) Result 03 2422 20.69 30.00 1.0000 Pass 06 2437 22.15 30.00 1.0000 Pass 09 2452 22.01 30.00 1.0000 Pass Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 124 of 145 Test Mode TX BE(EHT20) Mode_Ant 1 Channel Frequency (MHz) Output Power (dBm) Duty Factor (dB) Output Power + Duty Factor (dBm) Max. Limit (dBm) Max. Limit (W) Result 01 2412 16.94 0.11 17.05 30.00 1.0000 Pass 06 2437 22.58 0.11 22.69 30.00 1.0000 Pass 11 2462 18.94 0.11 19.05 30.00 1.0000 Pass Test Mode TX BE(EHT20) Mode_Ant 2 Channel Frequency (MHz) Output Power (dBm) Duty Factor (dB) Output Power + Duty Factor (dBm) Max. Limit (dBm) Max. Limit (W) Result 01 2412 16.97 0.11 17.08 30.00 1.0000 Pass 06 2437 22.79 0.11 22.90 30.00 1.0000 Pass 11 2462 18.96 0.11 19.07 30.00 1.0000 Pass Test Mode TX BE(EHT20) Mode_Total Channel Frequ…

Text truncated - open the document above for the full version.

Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 1 of 145 FCC Radio Test Report FCC ID: 2BH7FBE670 This report concerns: Original Grant Project No. : 2508C300 Equipment : BE12000 Tri-Band Wi-Fi 7 Router Brand Name : tp-link Model Name : Archer BE670, Archer BE12000 Applicant : TP-Link Systems Inc. Address : 10 Mauchly, Irvine, CA 92618 Manufacturer : TP-Link Systems Inc. Address : 10 Mauchly, Irvine, CA 92618 Date of Receipt : Aug. 21, 2025 Date of Test : Aug. 22, 2025 ~ Nov. 20, 2025 Issued Date : Dec. 30, 2025 Test Sample : Engineering Sample No.: DG920250821110 for radiated and AC power line conducted, DG920250821109 for conducted. Standard(s) : FCC CFR Title 47, Part 15, Subpart C The above equipment has been tested and found compliance with the requirement of the relative standards by BTL Inc. (Dongguan) Prepared by : Terry Deng Approved by : Chay Cai No.3, Jinshagang 1st Road, Dalang, Dongguan, Guangdong People’s Republic of China. Te l : + 8 6-769-8318-3000 Web: www.newbtl.com Service mail: [email protected] Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 2 of 145 Declaration BTL represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with standards traceable to international standard(s) and/or national standard(s). BTL's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTL assumes no responsibility for the data provided by the customer, any statements, inferences or generalizations drawn by the customer or others from the reports issued by BTL. The report must not be used by the client to claim product certification, approval, or endorsement by A2LA or any agency of the U.S. Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and ourselves, the test report shall not be reproduced, except in full, without our written approval. BTL’s laboratory quality assurance procedures are in compliance with the ISO/IEC 17025: 2017 requirements, and accredited by the conformity assessment authorities listed in this test report. BTL is not responsible for the sampling stage, so the results only apply to the sample as received. The information, data and test plan are provided by manufacturer which may affect the validity of results, so it is manufacturer’s responsibility to ensure that the apparatus meets the essential requirements of applied standards and in all the possible configurations as representative of its intended use. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Please note that the measurement uncertainty is provided for informational purpose only and are not use in determining the Pass/Fail results. Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 3 of 145 Table of Contents Page REVISION HISTORY 6 1 . APPLICABLE STANDARDS 7 2 . SUMMARY OF TEST RESULTS 7 2.1 TEST FACILITY 8 2.2 MEASUREMENT UNCERTAINTY 8 2.3 TEST ENVIRONMENT CONDITIONS 9 3 . GENERAL INFORMATION 10 3.1 GENERAL DESCRIPTION OF EUT 10 3.2 DESCRIPTION OF TEST MODES 12 3.3 PARAMETERS OF TEST SOFTWARE 14 3.4 DUTY CYCLE 15 3.5 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 17 3.6 SUPPORT UNITS 17 3.7 CUSTOMER INFORMATION DESCRIPTION 17 4 . AC POWER LINE CONDUCTED EMISSIONS 18 4.1 LIMIT 18 4.2 TEST PROCEDURE 18 4.3 DEVIATION FROM TEST STANDARD 18 4.4 TEST SETUP 19 4.5 EUT OPERATION CONDITIONS 19 4.6 TEST RESULTS 19 5 . RADIATED EMISSIONS 20 5.1 LIMIT 20 5.2 TEST PROCEDURE 21 5.3 DEVIATION FROM TEST STANDARD 22 5.4 TEST SETUP 22 5.5 EUT OPERATION CONDITIONS 24 5.6 TEST RESULTS - 9 KHZ TO 30 MHZ 24 5.7 TEST RESULTS - 30 MHZ TO 1000 MHZ 24 5.8 TEST RESULTS - ABOVE 1000 MHZ 24 6 . BANDWIDTH 25 6.1 LIMIT 25 Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 4 of 145 Table of Contents Page 6.2 TEST PROCEDURE 25 6.3 DEVIATION FROM STANDARD 25 6.4 TEST SETUP 25 6.5 EUT OPERATION CONDITIONS 25 6.6 TEST RESULTS 25 7 . MAXIMUM OUTPUT POWER 26 7.1 LIMIT 26 7.2 TEST PROCEDURE 26 7.3 DEVIATION FROM STANDARD 26 7.4 TEST SETUP 26 7.5 EUT OPERATION CONDITIONS 26 7.6 TEST RESULTS 26 8 . CONDUCTED SPURIOUS EMISSIONS 27 8.1 LIMIT 27 8.2 TEST PROCEDURE 27 8.3 DEVIATION FROM STANDARD 28 8.4 TEST SETUP 28 8.5 EUT OPERATION CONDITIONS 28 8.6 TEST RESULTS 28 9 . POWER SPECTRAL DENSITY 29 9.1 LIMIT 29 9.2 TEST PROCEDURE 29 9.3 DEVIATION FROM STANDARD 29 9.4 TEST SETUP 29 9.5 EUT OPERATION CONDITIONS 29 9.6 TEST RESULTS 29 10 . MEASUREMENT INSTRUMENTS LIST 30 11 . EUT TEST PHOTO 32 APPENDIX A - AC POWER LINE CONDUCTED EMISSIONS 38 APPENDIX B - RADIATED EMISSION - 9 KHZ TO 30 MHZ 41 APPENDIX C - RADIATED EMISSION - 30 MHZ TO 1000 MHZ 46 APPENDIX D - RADIATED EMISSION- ABOVE 1000 MHZ 49 Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 5 of 145 Table of Contents Page APPENDIX E - BANDWIDTH 112 APPENDIX F - MAXIMUM OUTPUT POWER 119 APPENDIX G - CONDUCTED SPURIOUS EMISSIONS 126 APPENDIX H - POWER SPECTRAL DENSITY 139 Report No.: BTL-FCCP-1-2508C300 Report Version: R01 Page 6 of 145 REVISION HISTORY Report No. Version Description Issued Date Note BTL-FCCP-1-2508C300 R00 Original Report. Dec. 15, 2025 Invalid BTL-FCCP-1-2508C300 R01 This report correctted the word “Te s t” on page 9. lt is a revision of the report BTL-FCCP-1-2508C300 R00. This is a newly released report, replacing the BTL-FCCP-1-2508C300 R00 report. Dec. 26, 2025 Invalid BTL-FCCP-1-2508C300 R01 This report added the Test mode description on page 13. lt is a revision of the report BTL-FCCP-1-2508C300 R01. This is a newly released report, replacing the BTL-FCCP-1-2508C300 R01 report. Dec. 31, 2025 Valid Report No.: BTL-FCCP-1-2508C300 Report V…

Text truncated - open the document above for the full version.

Copyright © 2024 TP-Link Systems Inc. All rights reserved FCC Composite Gain Test Report TP-Link Systems Inc. 10 Mauchly, Irvine, CA 926187 Copyright © 2024 TP-Link Systems Inc. All rights reserved Copy…

Text truncated - open the document above for the full version.