2BH7FFUSGPLUSV2Fusion G+ Gateway

Regulatory Compliance Omada Fusion G+ Gateway © 2026 TP-Link FCC compliance information statement Product Name: Omada Fusion G+ Gateway Model Number: Fusion G+ Component NameModel I.T.E. PowerAD-0150500300US-1 Responsible party: TP-Link Systems Inc. Address: 10 Mauchly, Irvine, CA 92618 Website: https://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6804 E-mail: [email protected] This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This de vice may not cause harmful interference. 2. This de vice must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” We,TP-Link Systems Inc., has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated. Issue Date: 2026.03.02 FCC compliance information statement Product Name: I.T.E. Power Supply Model Number: AD-0150500300US-1 Responsible party: TP-Link Systems Inc. Address: 10 Mauchly, Irvine, CA 92618 Website: https://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6804 E-mail: [email protected] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment int o an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This de vice must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. We, TP-Link Systems Inc., has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated. Issue Date: 2026.04.01 CE Mark Warning This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. OPERATING FREQUENCY (the maximum transmitted power) 2400 MHz -2483.5 MHz(20dBm) EU declaration of conformity TP-Link hereby declares that the gateway is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce RF Exposure Information The device complies with RF specifications when the device used at 20 cm from your body. UKCA Mark UK Declaration of Conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017. The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca Canadian Compliance Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This de vice may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation o…

Text truncated - open the document above for the full version.

Fusion Gateway Quick Installation Guide Note: Fusion gateways are for enterprise installation and use. Fusion 2.5G is used as an example throughout the guide. Images may differ from your actual product. Fusion Gateway 2.5G PoE SwitchPoE Gigabit Switch Wall Plate AP Celling Mount AP Outdoor AP Management PC Managed Switch Non-PoE Gigabit Switch Office Area, Meeting Room Celling Mount AP Office Area, Meeting Room PC PC PC PC Department A Department B Open a web browser and type the default management address https://omada.local or https://192.168.188.1 in the address field of the browser, then press the Enter ke y. 4. Make sure the management PC is configured to Obtain an IP address automatically. 3. Follow the setup wizard to configure the internet settings, bind the gateway to your TP-Link ID, set up the controller, and add devices. 5. After the setup wizard is complete, you will be directed to the management page. And you can configure more settings and manage your network. 6. For detailed information and configuration, refer to the gateway's user guide. The guide can be found on the Documents page of our official website: https://support.omadanetworks.com/document/. Initial Setup The Fusion gateway delivers an all-in-one solution for networking and centralized management on a single device, featuring a built-in controller for the entire Omada ecosystem. It is ideal for small businesses across single or multiple sites. This Quick Installation Guide is for qualified IT staff and professional installers. It covers typical network topology, basic software configuration, and descriptions of enterprise-dedicated features. For detailed instructions, refer to the user guide. Enterprise Solution Connect the Internet port (Port 1) of the gateway to the internet using the provided Ethernet cable. 1. Connect the gateway to a grounded power outlet using the provided power adapter. The touchscreen on the front panel will light up. 2. Via Omada Cloud Portal a. Enable Cloud Access on the Settings page on the gateway and bind a TP-Link ID to your gateway. If you have configured this in the setup wizard, skip the step. b. Launch a web browser and enter https://omada.tplinkcloud.com in the address bar. c. Enter your TP-Link ID and password to log in. A list of Fusion gateways that have been bound with your TP-Link ID will appear in the Fusion Systems page. Then you can launch your device to further configure the gateway. With the TP-Link Omada app, you can access and manage your Omada devices at a local site or remotely. More Management Methods Via Omada App Typical Network Topology Software Configuration Safety PrecautionsPreface ©2026 TP-Link 7100003112 REV1.0.0 Internet • Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. • Do not use damaged charger or USB cable to charge the device. • Do not use any other chargers than those recommended. • Adapter shall be installed near the equipment and shall be easily accessible. • Keep the device away from water, fire, humidity or hot environments. • For enterprise installation and use only. Flip Over to Explore More More Resources Main Sitehttps://www.omadanetworks.com/ https://support.omadanetworks.com/video/ https://support.omadanetworks.com/document/ https://support.omadanetworks.com/product/ https://support.omadanetworks.com/contact-support/ Video Center Product Support Documents Technical Support EU Declaration of Conformity TP-Link hereby declares that the gateway is in compliance with the essential requirements and other relevant provisions of directives (EU)2015/863, 2014/53/EU and 2011/65/EU. The original EU declaration of conformity may be found at https://www.tp-link.com/en/support/ce/. UK Declaration of Conformity TP-Link hereby declares that [product name] is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017. The original UK declaration of conformity may be found at https://www.tp-link.com/support/ukca/ Frequently Asked Questions (FAQ) Q1. Why were no APs or switches found during the initial setup? A: During initial setup, only devices in factory mode can be detected. Otherwise, they can only be detected and adopted after setup using their original account and password. Q2. How do I reset the Fusion gateway? A: • Via the physical Reset button With the device powered on, use a pin to press and hold the Reset button on the front panel for about 5 seconds until a reset prompt appears, then release. The device will restore to its factory default settings. • Via the web management page Go to Settings > System Settings > OS Settings. In the Action drop-down list, click Reset to reset the device to its factory default settings. Q3. How do I adopt APs and switches? A: 1. Connect the APs/switches to the same network as the gateway. 2. Access the gateway's management page at https://omada.local or https://192.168.188.1. 3. Go to Devices, you will find the devices displayed in the Device List. 4. Click Adopt and wait until the device’s S TAT U S changes to CONNECTED. *These features refer to functions supported by the switches adopted by the Fusion gateway and can be configured through it. Appendix Enterprise-Dedicated Features Fusion gateways are FCC Class A certified products with various advanced software capabilities, primarily used in business, industrial, or office environments. ■ Multi-Site Networking and Management: Features an enterprise-grade SD-WAN for multi-site networking in business scenarios (e.g., chain supermarkets and chain restaurants) and Cloud Portal for managing multiple sites. • Sites are interconnected via encrypted tunnels, forming a unified enterprise WAN and ensuring secure and reliable communication across geographically distributed locations. All network configuration, site onboarding, and policy management are performed exclusively through a cloud management portal. Local or on-premises controllers are not supported…

Text truncated - open the document above for the full version.

TP-Link Systems Inc. 092723-17 rev 10 Certification Application Attestation Statements Date: April 22, 2026 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) ______ TP-Link Systems Inc._____ certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> Statement for 47 CFR section 2.911(d)(5)(ii) ______ TP-Link Systems Inc._____ (“the applicant”) certifies that, as of the date of the filing of this application, the applicant ☐ - is / - is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates – see KDB 986446 Question 5) as an entity producing “covered” equipment. The applicant also certifies that the device does not have cybersecurity and/or anti-virus software produced by Kaspersky Lab, Inc or any of its successors and assignees identified on the covered list installed on the device, nor will it be installed by the applicant at any time after certification. Thank you, By: __________________________ _______ Sarah Wang _________________ (Signature 2 ) (Print name) Title: _____ Regulatory Compliance Manager _____________________ Company: ___ TP-Link Systems Inc. ______ Telephone: __+86 755 21534921_______________________ 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters must be placed on appropriate letterhead.

TP-Link Systems Inc. U.S. Agent Designation for Service of Process TO: American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 ATTENTION: FCC Certification – Section 2.911(d)(7) Information This letter is to confirm that the Applicant will also serve as the U.S. Agent for Service of Process as required by 47 CFR 2.911(d)(7). The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The Applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information changes. Applicant Company name: TP-Link Systems Inc. FRN #: 0035788017 Grantee Code: 2BH7F FCC ID: 2BH7FFUSGPLUSV2 Contact Name: Sarah Wang Street Address: 10 Mauchly, Irvine, CA 92618 City/Province/Zip: Irvine, CA 92618 Telephone No: (626) 333-0234 Email: [email protected] Applicant Signature: Date:2026.04.22 Signed by (Printed Name/Title): Sarah Wang/ Product Compliance Manager

TP-Link Systems Inc. 030122-15 Authority to Act as Agent Date: April 22, 2026 A merican Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 T o Whom It May Concern: BTL Inc./Rose Liu is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: 2027.4.21 By: __________________________ Sarah Wang (Signature 1 ) (Print name) Title: Regulatory Compliance Manager On behalf of: TP-Link Systems Inc. (Company Name) Telephone: 6263330234 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

TP-Link Systems Inc. 030122-15 Request for Confidentiality Date: April 22, 2026 Subject: Confidentiality Request for: 2BH7FFUSGPLUSV2 Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 12.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit ☐ Short Term ☒ Permanent Block Diagrams ☐ Short Term External Photos ☐ Short Term ☐ Permanent * 1 Internal Photos ☐ Short Term ☒ Permanent Operation Description/Theory of Operation ☐ Short Term ☐ Permanent Parts List & Placement/BOM ☐ Short Term ☐ Permanent Tune-Up Procedure ☐ Short Term ☒ Permanent Schematics ☐ Short Term Test Setup Photos ☐ Short Term ☐ Permanent * 3 User’s Manual TP-Link Systems Inc. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By: Regulatory Compliance Manager Sarah Wang (Signature/Title 3 ) (Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Please refer to https://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

TP-Link Systems Inc. Declaration Letter – Enterprise-Grade Commercial Gateway Date: April 22, 2026 Name: TP-Link Systems Inc. Address: 10 Mauchly, Irvine, CA 92618 Product: Fusion G+ Gateway FCC ID: 2BH7FFUSGPLUSV2 Model: Fusion G+ Brand: Omada To Whom It May Concern, This letter serves as an official statement to formally confirm and clarify the product nature, positioning, core functions of the Fusion G+ Gateway from the Omada Fusion Gateway Series. The Fusion G+ is designed, developed, and marketed exclusively as an enterprise-grade networking device, intended solely for enterprise environments, and is not intended for household or consumer use. The Product’s positioning and features are as follows: 1. Product Positioning and Target Customers The Fusion Gateway is positioned as an enterprise-grade gateway dedicated to enterprise networking scenarios. Primary customers include professional installers, managed service providers (MSPs), and enterprise- level users. Detailed information about the Omada enterprise networking solution portfolio is available on the official website: https://www.omadanetworks.com/ https://www.omadanetworks.com/us/business-networking/solution/small-sized-chain- restaurants-stores/ 2. Product Packaging and Color Box The product outer packaging is clearly and prominently labeled with “Enterprise Solution” to identify its enterprise-level purpose. 3. Product Manual The product includes a detailed user manual with “Enterprise Solution” clearly marked on the cover.The manual states that the device is a sophisticated system eng TP-Link Systems Inc. ineered for enterprise scenarios, with these enterprise-grade software features: • Multi-Site Networking and Management: Commercial-grade SD-WAN for multi- site deployment in chain retail, restaurants, and other enterprise environments; cloud portal for centralized multi-site management. • Centralized Management Functionality: Unified management of all network devices including enterprise-grade L3 switches, EAPs, and other equipment. • Enterprise Network Stability Assurance: Multiple WAN connections and WAN failover functionality to ensure reliable network operation. • Enterprise-Grade Configuration & Management: Professional CLI configuration, batch port configuration across switches, and support for the SNMP management protocol. • Enterprise-Grade Operations & Maintenance: Enterprise- level packet capture, network traffic statistical report export, and audit log support. • Enterprise-Grade Access Authentication: External RADIUS / External Portal / Voucher, PPSK(Private Pre-Shared Key), and 802.1x / MAC-Based Authentication. 4. Enterprise-Grade L3 Network Feature Management The Fusion G+ Gateway supports full management of professional enterprise- grade Layer 3 switches, enabling end-to-end enterprise network control. 5. FCC Certification Classification This product is classified under FCC Class A, a certification intended for digital equipment used in enterprise environments, consistent with its enterprise-grade positioning. We greatly appreciate your professional guidance and assistance regarding the FCC certification clarification process. We confirm that all design, features, labeling, and certifications of the Fusion G+ Gateway strictly comply with enterprise and commercial device requirements. Sincerely, Sarah Wang TP-Link Systems Inc. Product Compliance Manager

Professional Installation Attestation We Name: TP-Link Systems Inc. Address: 10 Mauchly, Irvine, CA 92618 Declare that the following product is a professionally installed device. The reasons are as follows: 1.This device is intended for industrial or commercial use. 2.This device is sold to agents or distributors. 3.This product installation requires training. Technical support team will provide professional training to agents or dealers, including but not limited to product power supply, product installation, product deployment, product management, configuration, etc. 4.This product needs to be professionally configured by Controller network service before use. Sincerely, _________________ Name: Sarah Wang Position: Regulatory compliance manager Date: 20260422 P r oduct: FCC ID: M odel: B r and: Fusion G+ Gateway 2BH7FFUSGPLUSV2 Fusion G+ Omada

Project No.: 2604C073 Page 2 of 12 Project No.: 2604C073 Page 3 of 12 Project No.: 2604C073 Page 4 of 12 Project No.: 2604C073 Page 5 of 12 Project No.: 2604C073 Page 6 of 12 Project No.: 2604C073 Page 7 of 12

C B A 12 C 345678 B E D D A 9 12345 E 6789 Model: Fusion G+ Fusion G+ Gateway S/N:XXXXXXXXXXXXXUN/2.6 M AC : X X-X X-X X-X X-X X-X X Device Key:XXXX-XXXX-XXXX-XXXX-XXXX FCC ID: 2BH7FFUSGPLUSV2 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. MADE IN VIETNAM Enterprise Solution Power: 5V 3.0A

Project No.: 2604C073 Page 9 of 12 ANT. Project No.: 2604C073 Page 10 of 12 Project No.: 2604C073 Page 11 of 12

Project No.: 2604C073 Page 12 of 12

Report No.: BTL-FCCP-2-2604C073 Report Version: R01 Page 1 of 7 FCC RF EXPOSURE REPORT FCC ID: 2BH7FFUSGPLUSV2 Project No. : 2604C073 Equipment : Fusion G+ Gateway Brand Name : Omada Test Model : Fusion G+ Model Name : Fusion G+ Hardware Version : 2.0 Software Version : 1.0 Applicant : TP-Link Systems Inc. Address : 10 Mauchly, Irvine, CA 92618 Manufacturer : TP-Link Systems Inc. Address : 10 Mauchly, Irvine, CA 92618 Date of Receipt : Apr. 08, 2026 Date of Test : Apr. 08, 2026 ~ Apr. 20, 2026 Issued Date : Apr. 27, 2026 Test Sample : Engineering Sample No.: DG920260408301 Standard(s) : FCC Guidelines for Human Exposure IEEE C95.1 & KDB 447498 D04 v01 The above equipment has been tested and found compliance with the requirement of the relative standards by BTL Inc. (Dongguan) Prepared by : Terry Deng Approved by : Chay Cai No.3, Jinshagang 1st Road, Dalang, Dongguan, Guangdong People’s Republic of China. Te l : + 8 6-769-8318-3000 Web: www.newbtl.com Service mail: [email protected] Report No.: BTL-FCCP-2-2604C073 Report Version: R01 Page 2 of 7 Declaration BTL represents to the client that testing is done in accordance with standard procedures as applicable and th at test instruments used has been calibrated with standards traceable to international standard(s) and/or national standard(s). BTL's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTL assumes no responsibility for the data provided by the customer, any statements, inferences or generalizations drawn by the customer or others from the reports issued by BTL. This report is the confidential property of the client. As a mutual protection to the clients, the public and ourselves, the test report shall not be reproduced, except in full, without our written approval. BTL is not responsible for the sampling stage, so the results only apply to the sample as received. The information, data and test plan are provided by manufacturer which may affect the validity of results, so it is manufacturer’s responsibility to ensure that the apparatus meets the essential requirements of applied standards and in all the possible configurations as representative of its intended use. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Please note that the measurement uncertainty is provided for informational purpose only and are not use in determining the Pass/Fail results. Report No.: BTL-FCCP-2-2604C073 Report Version: R01 Page 3 of 7 REVISION HISTORY Report No. Version Description Issued Date Note BTL-FCCP-2-2604C073 R00 Original Report. Apr. 23, 2026 Invalid BTL-FCCP-2-2604C073 R01 This report add Chapter 3 Note(1). It is a revision of the report with serial number BTL-FCCP-2-2604C073 R00. This is a newly released report, replacing the BTL-FCCP-2-2604C073 R00 report. Apr. 27, 2026 Valid Report No.: BTL-FCCP-2-2604C073 Report Version: R01 Page 4 of 7 1. GENERAL CONCULUSION According to FCC §§1.1307 and KDB 447498 D04 v01, the available maximum time-averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold P th (mW). 1) Option A. 1-mW Test Exemption Per § 1.1307(b)(3)(i)(A), a single RF source is exempt RF device (from the requirement to show data demonstrating compliance to RF exposure limits, as previously mentioned) if the available maximum time-averaged power is no more than 1 mW, regardless of separation distance. This exemption applies to all operating configurations and exposure conditions, for the frequency range 100 kHz to 100 GHz, regardless of fixed, mobile, or portable device exposure conditions. This is a standalone exemption, and it cannot be applied in conjunction with any other test exemption. 2) Option B. SAR-Based Exemption A more comprehensive exemption, considering a variable power threshold that depends on both the separation distance and power, is provided in § 1.1307(b)(3)(i)(B). This exemption is applicable to the frequency range between 300 MHz and 6 GHz, with test separation distances between 0.5 cm and 40 cm, and for all RF sources in fixed, mobile, and portable device exposure conditions. Accordingly, a RF source is considered an RF exempt device if its available maximum time-averaged (matched conducted) power or its effective radiated power (ERP), whichever is greater, are below a specified threshold. This method shall only be used at separation distances (cm) from 0.5 centimeters to 40 centimeters and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by: Report No.: BTL-FCCP-2-2604C073 Report Version: R01 Page 5 of 7 Table B2-Example Power Thresholds (mW) Frequency (MHz) Distance(mm) mW 5 10 15 20 25 30 35 40 45 50 300 39 65 88 110 129 148 166 184 201 217 450 22 44 67 89 112 135 158 180 203 226 835 9 25 44 66 90 116 145 175 207 240 1900 3 12 26 44 66 92 122 157 195 236 2450 3 10 22 38 59 83 111 143 179 219 3600 2 8 18 32 49 71 96 125 158 195 5800 1 6 14 25 40 …

Text truncated - open the document above for the full version.