2BH7V-BK61Car wireless charging mount

Car wireless charging mount DC15V/3A,9V/3A,5V3A(PD45W) 115kHz ~ 205KHz 115kHz ~ 205KHz DC15V/3A,9V/3A,5V3A(PD45W) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. -This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Shenzhen Zhiding Manufacturing Co., Ltd Covered Equipment Certification Attestation Letter 12/19/2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2BH7V-BK61 Shenzhen Zhiding Manufacturing Co., Ltd (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Shenzhen Zhiding Manufacturing Co., Ltd (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Shenzhen Zhiding Manufacturing Co., Ltd (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). <Signature>: Name: Deng Hui Luo Title: Manager Company: Shenzhen Zhiding Manufacturing Co., Ltd Date: 12/19/2025

Shenzhen Zhiding Manufacturing Co., Ltd * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter 12/19/2025 TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTN.: Reviewing Engineer FCC ID: 2BH7V-BK61 FRN of applicant: 0035788850 Per section 2.911(d)(7) of the FCC rules, [Shenzhen Zhiding Manufacturing Co., Ltd] (“the applicant”) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: Herland International Trading Inc FCC Registration Number (FRN): 0036324101 Physical U.S. Company Address: 1370 Valley Vista Dr Ste 200 Diamond Bar, CA 91765 Contact Person: Jianfeng Gao Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Signed: Printed name: Deng Hui Luo Title: Manager Company Name: Shenzhen Zhiding Manufacturing Co., Ltd Date: 12/19/2025 Agent Signed (if different from Applicant): Signed: Printed name: Jianfeng Gao Title: Manager Company Name: Herland International Trading Inc Date: 12/19/2025

Shenzhen Zhiding Manufacturing Co., Ltd 2025-12-19 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen DL Testing Technology Co., Ltd.（101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China）to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Shenzhen Zhiding Manufacturing Co., Ltd（Room 401, No. 1 Factory Building, Scary Industrial Plant, No.7 Ganli 6th Road, Gankeng Community, Jihua Street,Longgang District,Shenzhen ） <Signature>: Name: Deng Hui Luo Title: Manager Company: Shenzhen Zhiding Manufacturing Co., Ltd

Shenzhen Zhiding Manufacturing Co., Ltd 2025-12-19 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, <Signature>: Name: Deng Hui Luo Title: Manager Company: Shenzhen Zhiding Manufacturing Co., Ltd

Shenzhen Zhiding Manufacturing Co., Ltd 2025-12-19 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BH7V-BK61 Product Name: Car wireless charging mount Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature>: Name: Deng Hui Luo Title: Manager Company: Shenzhen Zhiding Manufacturing Co., Ltd

Shenzhen Zhiding Manufacturing Co., Ltd Product Similarity Declaration Applicant: Shenzhen Zhiding Manufacturing Co., Ltd Address: Room 401, No. 1 Factory Building, Scary Industrial Plant, No.7 Ganli 6th Road, Gankeng Community, Jihua Street,Longgang District,Shenzhen Manufacturer: Shenzhen Zhiding Manufacturing Co., Ltd Address: Room 401, No. 1 Factory Building, Scary Industrial Plant, No.7 Ganli 6th Road, Gankeng Community, Jihua Street,Longgang District,Shenzhen Product Name: Car wireless charging mount Trade Mark: N/A Model Number: BK61, BK61X, BK61S, BK61L We (Shenzhen Zhiding Manufacturing Co., Ltd) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.,), same mechanical structure and design (including product enclosure, materials, etc.,), All models are the same as the samples except for the model names and appearance color. <Signature>: Name: Deng Hui Luo Title: Manager Company: Shenzhen Zhiding Manufacturing Co., Ltd

Shenzhen DL Testing Technology Co., Ltd. EUT PHOTO(External Photos) Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. ※※※※※ END OF REPORT ※※※※※

Size: 20*16mm M/N: BK61 FCC ID: 2BH7V-BK61 Label location

Shenzhen DL Testing Technology Co., Ltd. EUT PHOTO(Internal Photos) ANT Shenzhen DL Testing Technology Co., Ltd. ※※※※※ END OF REPORT ※※※※※

RF Exposure Evaluation FCC ID: 2BH7V-BK61 Product: Car wireless charging mount Trade Mark: N/A Model No.: BK61, BK61X, BK61S, BK61L Model Difference: All models are same as the samples except model name and appearance color, they have the same structure and circuit. Transmitting mode Keep the EUT in continuously wireless charging mode Power supply: Rated Input: DC15V/3A,9V/3A,5V3A(PD45W) Rated Output: 25W(MAX)/15W/10W/7.5W/5W Date of Receipt: Dec. 27, 2025 Test Date: Dec. 27, 2025 - Jan. 06, 2026 Date of Report: Jan. 06, 2026 Mode1. Wireless Phone Output Mode(5W) Mode2. Wireless Phone Output Mode(7.5W) Mode3. Wireless Phone Output Mode(10W) Mode4. Wireless Phone Output Mode(15W) Mode5. Wireless Phone Output Mode(25W) Note: 1. We have evaluated 1%, 50% and 99% battery charging mode, and the worst mode (99%) is showed in this report. 2. All modes have been tested, and the report only shows the results of the worst mode 5. 1 Measuring Standard According to Part 2.1091 RF exposure is calculated. According KDB 680106 D01 WirelessPower Transfer v04. 2 Requirements ①According to the item 5 of KDB680106 D01v04: ②Inductive wireless power transfer applications that meet all of the following requirements are excluded from submitting an RF exposure evaluation. 3 Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) 4 Test Setup 5 Test Procedure 1) The RF exposure test was performed in anechoic chamber. 2) The measurement probe was placed at test distance (20 cm from all sides and 20 cm from the top) which is between the edge of the charger and the geometric center of probe. 3) The highest emission level was recorded and compared with limit as soon as measurement of each points (A, B, C, D, E) were completed. 4) The EUT was measured according to the dictates of KDB680106 D01v04. Remark：The EUT’s test position A, B, C, D and E is valid for the E and H field measurements. 6 Description of Support Units Mobile phone (Provide by test lab): Manufacturer: SAMSUNG Model: Galaxy S21 5G 7 Test Instruments list Test Equipment Manufacturer Model No. SN. Cal.Date (mm-dd-yy) Cal.Due date (mm-dd-yy) Exposure Level Tester Narda ELT-400 N-0231 Oct. 25, 2025 Oct. 24, 2026 Magnetic field probe 100cm 2 Narda ELT probe 100cm 2 M0675 Oct. 25, 2025 Oct. 24, 2026 Field Probe ETS HI-6105 / Oct. 25, 2025 Oct. 24, 2026 Laser Data Interface ETS HI-6113 / Oct. 25, 2025 Oct. 24, 2026 8 Test Uncertainty E-Filed Strength(1Hz-400kHz) : ±0.08V/m H-Filed Strength(1Hz-400kHz) : ±0.02A/m uT : ±0.01 Note: The field intensity value A/m in the report is converted from uT, and the formula is as follows: 9 Test Result E-Filed Strength at 20 cm from the edges surrounding the EUT Frequency Range (MHz) Test Position A (V/m) Test Position B (V/m) Test Position C (V/m) Test Position D (V/m) Test Position E (V/m) Limits (V/m) 0.115-0.205 0.13 0.22 0.14 0.25 0.36 614 H-Filed Strength at 20 cm from the edges surrounding the EUT (uT) Frequency Range (MHz) Test Position A Test Position B Test Position C Test Position D Test Position E 0.115-0.205 0.436 0.741 0.755 0.641 0.785 H-Filed Strength at 20 cm from the edges surrounding the EUT Frequency Range (MHz) Test Position A (A/m) Test Position B (A/m) Test Position C (A/m) Test Position D (A/m) Test Position E (A/m) Limits (A/m) 0.115-0.205 0.349 0.593 0.604 0.513 0.628 1.63 10 Test Set-up Photo

1.MECHANICAL DIMENSION (UNIT:mm) 2.SCHEMATICS: ABC DEH 42.5±0.520.5±0.5 0.8±0.5 15±3 4±2 2.5Max 3.WINDING： STE P TAPE REMAR K N1 4.ELECTRICAL SPECIFICATION: ITEM SPEC 5.BILF OF MATERIAL： NO.SGS NO. 1 2 3 4 5 page:2/2 何伟华韦立红韦立红 TES T CON 备注：1.加20*1.0MM小磁片 2. 加9448背胶 HRSW ELECTRONICS CO.,LTD ADD: 2nd Floor, Building 1, No. 48, Huanguan Middle Road, Guanlan, Longhua New District, Shenzhen City PART NO TITLE G42.5开槽+磁吸线圈+小磁片+胶 50MM DRAWN BYCHECKED BY APPROVED BY 胶水 黄胶9999 LIANCHENG CO.,LTD 高温胶纸 4mm宽高温胶纸 CUDAK CO.,LTD 无铅锡条无铅锡条 QIAODO 磁片 ⌀42.5*0.8锰锌硬磁片开L槽 TAIYI CO.,LTD ITEMMATERIAL SPECIFICATIONMANUFACTURER 热风线热风线0.08*80股 NANJINGJINNINGCO,LTD 100KHz,0.25V AT 25°C 8.1UH±10% 60 mΩ Max 80°C HI-POT 线圈加磁片 S-F常规状态 S-F 热风线⌀0.08*80mm 2UEW 11TS (Ref) LDCR温度 SPECIFICATION FOR APPROVAL 备注 磁片中间要加20*1.0小磁片 START-FINISHWIRE TYPETURNS

Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251227027R Test ReportTel: 400-688-3552Web:www.dl-cert.comEmail: [email protected] Page 1 of 18 TEST REPORT FCC ID: 2BH7V-BK61 Applicant: Shenzhen Zhiding Manufacturing Co., Ltd Address: Room 401, No. 1 Factory Building, Scary Industrial Plant, No.7 Ganli 6th Road, Gankeng Community, Jihua Street,Longgang District,Shenzhen Manufacturer: Shenzhen Zhiding Manufacturing Co., Ltd Address: Room 401, No. 1 Factory Building, Scary Industrial Plant, No.7 Ganli 6th Road, Gankeng Community, Jihua Street,Longgang District,Shenzhen Product Name: Car wireless charging mount Trade Mark: N/A Model Number: BK61, BK61X, BK61S, BK61L Date of Receipt: Dec. 27, 2025 Test Date: Dec. 27, 2025 - Jan. 20, 2026 Date of Report: Jan. 20, 2026 Prepared By: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China Applicable Standards: FCC PART 15 Subpart C ANSI C63.10:2020 Test Result: Pass Report Number: DLE-251227027R Prepared (Engineer): Alisa Song Reviewer (Supervisor): Jack Bu Approved (Manager): Jade Yang This test report is based on a single evaluation of one sample of above mentioned products. It is not permitted to be duplicated in extracts without written approval of Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251227027R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 2 of 18 TABLE OF CONTENT Test Report Declaration Page 1. VERSION ................................................................................................................................... 3 2. TEST SUMMARY ..................................................................................................................... 3 3. GENERAL INFORMATION .................................................................................................... 4 4. TEST INSTRUMENT USED ................................................................................................... 6 5. CONDUCTED EMISSION TEST ........................................................................................... 7 6. RADIATION EMISSION TEST ............................................................................................ 11 7. BANDWIDTH TEST ............................................................................................................... 17 8. ANTENNA REQUIREMENT ................................................................................................ 18 9. SETUP PHOTOGRAPHS ..................................................................................................... 18 10. EUT PHOTOGRAPHS ....................................................................................................... 18 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251227027R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 3 of 18 1. VERSION Version No. Date Description 00 Jan. 06, 2026 Original 2. TEST SUMMARY EMC Emission Test Item Section in CFR 47 Result Remark AC Power Line Conducted Emission 15.207 PASS Spurious Emission 15.209(a)(f) PASS 20dB Bandwidth 15.215 PASS Antenna requirement 15.203 PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Test Lab: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China FCC Test Firm Registration Number: 854456 Designation Number: CN1307 IC Registered No.: 27485 CAB ID.: CN0118 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251227027R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 4 of 18 3. GENERAL INFORMATION 3.1 Description of Device (EUT) Product Name: Car wireless charging mount Trade Mark: N/A Model Number: BK61, BK61X, BK61S, BK61L Test Model: BK61 Model Difference: All models are same as the samples except model name and appearance color, they have the same structure and circuit. Serial No.: N/A Hardware version: H1.0 Software version: S1.0 Operation Frequency: 115kHz ~ 205KHz Modulation type: MSK Antenna Type: Inductive loop coil Antenna Antenna gain: 0dBi Power supply: Rated Input: DC15V/3A,9V/3A,5V3A(PD45W) Rated Output: 25W(MAX)/15W/10W/7.5W/5W 3.2 Tested System Details None. 3.3 Block Diagram of Test Set-up 3.4 Test Mode Description Mode1. Wireless Phone Output Mode(5W) Mode2. Wireless Phone Output Mode(7.5W) Mode3. Wireless Phone Output Mode(10W) Mode4. Wireless Phone Output Mode(15W) Mode5. Wireless Phone Output Mode(25W) Note: 1. We have evaluated 1%, 50% and 99% battery charging mode, and the worst mode (99%) is showed in this report. 2. All modes have been tested, and the report only shows the results of the worst mode 5. AC Mains EUT Adapter Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251227027R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 5 of 18 3.5 Test Auxiliary Equipment Mobile phone (Provide by test lab): Manufacturer: SAMSUNG Model: Galaxy S21 5G Adapter (Provide by test lab): Manufacturer: XIAOMI Model: AD65G I/P: AC 100-240V 50/60Hz O/P: DC 5V/3A, DC 9V/3A, DC 10V/5A, DC 12V/3A, DC 15V/3A, DC 20V/3.25A 3.6 Test Uncertainty Conducted Emission Uncertainty(150KHz-30MHz) : ±2.56dB 20dB Bandwidth : ±0.5kHz Radiated Emission Uncertainty(9KHz-1GHz) : ±3.24dB Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-251227027R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 6 of 18 4. TEST INSTRUMENT USED For Conducted Emission Test (843 Shielded Room) Equipment Manufacturer Model Serial Last Cal. Next Cal. 843 Shielded Room YIHENG 843 Room 843 Nov. 05, 2023 Nov. 04, 2026 EMI Receiver R&S ESR 101421 Oct. 25, 2025 Oct. 24, 2…

Text truncated - open the document above for the full version.

Shenzhen DL Testing Technology Co., Ltd. EUT TEST PHOTO Radiated Measurement Photos Shenzhen DL Testing Technology Co., Ltd. Conducted Emission Photos ※※※※※ END OF REPORT ※※※※※