2BH9K-ACG1144Vibrators

FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

Yunjuhui (Shenzhen) Technology Co., Ltd 8419,4th Floor,No.3012 Banxuegang Avenue, Bantian Community,Bantian Street,Longgang District,Shenzhen China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-9-20 To whom it may concern: We, Yunjuhui (Shenzhen) Technology Co., Ltd, hereby certify that the equipment for which authorization is sought (FCC ID: 2BH9K-ACG1144) is not “covered” equipment prohibited from receiving an equipment authorization pursuant to § 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing “covered” equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, Signature Luo Yi Manager Yunjuhui (Shenzhen) Technology Co., Ltd 62_[model] CoveredEqu_2.911(d)(5)(i) and (ii) - U, V03

Yunjuhui (Shenzhen) Technology Co., Ltd 8419, 4th Floor, No. 3012 Banxuegang Avenue, Bantian Community, Bantian Street, Longgang District, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024/09/19 U.S. Agent Designation YUNJUHUI (SHENZHEN) TECHNOLOGY CO., LTD acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BH9K-ACG1144): Name and company of U.S. agent: THREE STONES MEDIA LLC Physical U.S. address of agent: 1200 Broadway St. APT 329 Los Angeles, CA 90015 United States FRN of U.S. agent: 0033401761 Email address of U.S. agent: [email protected] THREE STONES MEDIA LLC acknowledges their obligation to accept service of process on behalf of YUNJUHUI (SHENZHEN) TECHNOLOGY CO., LTD. YUNJUHUI (SHENZHEN) TECHNOLOGY CO., LTD with the FRN [0035797935] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Luo Yi Principal YUNJUHUI (SHENZHEN) TECHNOLOGY CO., LTD. Signature Sijie Zhang CEO THREE STONES MEDIA LLC 48_[mo del] US_Agent_2.911(d)(7) - U, V0 5

Yunjuhui (Shenzhen) Technology Co., Ltd Add: 8419,4th Floor,No.3012 Banxuegang Avenue, Bantian Community,Bantian Street,Longgang District,Shenzhen China Date: 2024-9-20 FCC ID: 2BH9K-ACG1144 Dear Sir/Madam, We, Yunjuhui (Shenzhen) Technology Co., Ltd Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model: Product name: Vibrators Model no.: ACG1144, ACG1138, ACG1145, ACG0852, ACG1141, ACG1150, ACG1149, ACG1148, ACG1147, ACG1146, ACG1260, ACG1140, ACG0634, ACG0898, ACG1139 Sincerely, Name/Title： Luo Yi/Manager Company: Yunjuhui (Shenzhen) Technology Co., Ltd Address: 8419,4th Floor,No.3012 Banxuegang Avenue, Bantian Community,Bantian Street,Longgang District,Shenzhen China Phone: 15323734004 Fax: N/A E-Mail: [email protected]

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2024-9-20> Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2BH9K-ACG1144 ACG1144 For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title： Luo Yi/Manager Company: Yunjuhui (Shenzhen) Technology Co., Ltd Address: 8419,4th Floor,No.3012 Banxuegang Avenue, Bantian Community,Bantian Street,Longgang District,Shenzhen China Phone: 15323734004 Fax: N/A E-Mail: [email protected]

Yunjuhui (Shenzhen) Technology Co., Ltd 8419,4th Floor,No.3012 Banxuegang Avenue, Bantian Community,Bantian Street,Longgang District,Shenzhen China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-9-20 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2BH9K-ACG1144 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins’ current valid General Terms and Conditions (AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title： Luo Yi/Manager Company: Yunjuhui (Shenzhen) Technology Co., Ltd Address: 8419,4th Floor,No.3012 Banxuegang Avenue, Bantian Community,Bantian Street,Longgang District,Shenzhen China Phone: 15323734004 Fax: N/A E-Mail: [email protected]

FCC ID: 2BH9K-ACG1144 External Photos of the EUT FCC ID: 2BH9K-ACG1144 FCC ID: 2BH9K-ACG1144

Label and Location Size: L: 1.0cm*W: 0.2cm Label and Location FCC ID : 2BH9K-ACG1144

FCC ID: 2BH9K-ACG1144 Internal Photos of the EUT FCC ID: 2BH9K-ACG1144 FCC ID: 2BH9K-ACG1144 ANT

RF Exposure evaluation FCC ID: 2BH9K-ACG1144 1.1. Applicable Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1093 RF exposure requirement KDB447498 v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies 1.2. Requirement According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.23 “ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 1.3. Manufacturing tolerance Freq. (MHz) Field strength(max)(dBuV/m) EIRP (max) (dBm) Turn-up Power (dB) Max tune up power (dBm) [P] 433.91MHz 89.53 -5.73 -5.0±1 -4.0 Note: EIRP=E-104.8+20logD, D=3 Page 2 of 2 2. E v a l u a t i o n R e s u l t Evaluation Results Band/Mode f (GHz) Antenna Distance (mm) RF output power (including tune-up tolerance) SAR Test Exclusion Threshold SAR Test Exclusion dBm mW SRD 0.433 5 -4.0 0.3981 0.0524<3.0 Yes 3. C o n c l u s i o n The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06 .....................End of Report.........................

1. Antenna Description: Antenna type PCB antenna Model ACG1144 Frequency range 433 MHz Manufacturer Yunjuhui (Shenzhen) Technology Co., Ltd Gain 0.85 dBi 2. Antenna Photo: Length:9.20mm Width:12.56mm Length:21.78mm Width:1.21mm

Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China FCC PART 15 SUBPART C TEST REPORT FCC PART 15.231 Report Reference No. .................... : FCC ID. ........................................... : CTA24082800201 2BH9K-ACG1144 Compiled by ( position+printed name+signature) . : File administrators Jinghua Xiao Supervised by ( position+printed name+signature) . : Project Engineer Xudong Zhang Approved by ( position+printed name+signature) . : RF Manager Eric Wang Date of issue .................................... : Sep. 02, 2024 Testing Laboratory Name ............. : Shenzhen CTA Testing Technology Co., Ltd. Address ........................................... : Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Applicant’s name ........................... : Yunjuhui (Shenzhen) Technology Co., Ltd Address ............................................ : 8419, 4th Floor, No. 3012 Banxuegang Avenue, Bantian Community, Bantian Street, Longgang District, Shenzhen, China Test specification ........................... : Standard ........................................... : FCC Part 15.231 Shenzhen CTA Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTA Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTA Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description ..................... : Vibrators Trade Mark ....................................... : N/A Manufacturer .................................... : Yunjuhui (Shenzhen) Technology Co., Ltd Model/Type reference ...................... : ACG1144 Listed Models .................................. : ACG1138, ACG1145, ACG0852, ACG1141, ACG1150, ACG1149, ACG1148, ACG1147, ACG1146, ACG1260, ACG1140, ACG0634, ACG0898, ACG1139 Modulation ....................................... : ASK Frequency ......................................... 433.91MHz Ratings ............................................. : DC 12.0V From battery Result ............................................... : PASS Report No.: CTA24082800201 Page 2 of 23 T E S T R E P O R T Equipment under Test : Vibrators Model /Type : ACG1144 Listed Models : ACG1138, ACG1145, ACG0852, ACG1141, ACG1150, ACG1149, ACG1148, ACG1147, ACG1146, ACG1260, ACG1140, ACG0634, ACG0898, ACG1139 Applicant : Yunjuhui (Shenzhen) Technology Co., Ltd Address : 8419, 4th Floor, No. 3012 Banxuegang Avenue, Bantian Community, Bantian Street, Longgang District, Shenzhen, China Manufacturer : Yunjuhui (Shenzhen) Technology Co., Ltd Address : 8419, 4th Floor, No. 3012 Banxuegang Avenue, Bantian Community, Bantian Street, Longgang District, Shenzhen, China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: CTA24082800201 Page 3 of 23 Contents 1 T E S T S T A N D A R D S ................................................................. 4 2 S U M M A R Y ............................................................................ 5 2.1 General Remarks 5 2.2 Product Description 5 2.3 Equipment Under Test 5 2.4 Short description of the Equipment under Test (EUT) 5 2.5 Block Diagram of Test Setup 5 2.6 Special Accessories 6 2.7 Related Submittal(s) / Grant (s) 6 2.8 Modifications 6 3 T E S T E N V I R O N M E N T .............................................................. 7 3.1 Address of the test laboratory 7 3.2 Test Facility 7 3.3 Environmental conditions 7 3.4 Summary of measurement results 8 3.5 Statement of the measurement uncertainty 8 3.6 Equipments Used during the Test 8 4 T E S T C O N D I T I O N S A N D R E S U L T S ........................................... 10 4.1 AC Power Conducted Emission 10 4.2 Radiated Emission 11 4.3 20dB Bandwidth 15 4.4 Deactivation Time 16 4.5 Antenna Requirement 17 5 T E S T S E T U P P H O T O S O F T H E E U T ......................................... 18 6 P H O T O S O F T H E E U T ........................................................... 19 Report No.: CTA24082800201 Page 4 of 23 1 T E S T S T A N D A R D S The tests were performed according to following standards: FCC Rules Part 15.231:Periodic operation in the band 40.66-40.70 MHz and above 70 MHz. ANSI C63.10:2013 : American National Standard for Testing Unlicensed Wireless Devices Report No.: CTA24082800201 Page 5 of 23 2 S U M M A R Y 2.1 General Remarks Date of receipt of test sample : Aug. 28, 2024 Testing commenced on : Aug. 28, 2024 Testing concluded on : Sep. 02, 2024 2.2 Product Description Product Name: Vibrators Model/Type reference: ACG1144 Power supply: DC 12.0V From battery Testing sample ID： CTA240828002-1# (Engineer sample), CTA240828002-2#(Normal sample) Modulation: ASK Operation frequency: 433.91MHz Channel number: 1 Antenna type: PCB antenna Antenna gain: 0.85 dBi 2.3 Equipment Under Test Power supply system utilised Power supply voltage : ○ 230V / 50 Hz ○ 120V / 60Hz ○ 12 V DC ○ 24 V DC ● Other (specified in blank below) DC 12.0V From battery 2.4 Short description of the Equipment under Test (EUT) This is a Vibrators. For more details, refer to the user’s manual of the EUT. 2.5 Block Diagram of Test Setup EUT DC 12.0V from battery Report No.: CTA24082800201 Page 6 of 23 2.6 Special Accessories Follow auxiliary equipment(s) test with EUT that provided by the manufacturer or laboratory is listed as follow: Description Manufacturer Model Technical Parameters Certificate Provided by / / 2.7 Related Submittal(s) / Grant (s) This submittal(s) (test report) is intended for the device filin…

Text truncated - open the document above for the full version.

FCC ID: 2BH9K-ACG1144 Test Setup Photos of the EUT