2BHA2-LEAPMR15USB-C Desktop Magnetic Wireless Charger

FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 20 centimeters from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498.

- WINSTARS TECHNOLOGY LTD - Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 7/2/2024 U.S. Agent Designation WINSTARS TECHNOLOGY LTD acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BHA2-LEAPMR15): Name and company of U.S. agent: UUX GROUP INC Physical U.S. address of agent: 36 South 18th Avenue, Suite A Brighton, CO USA 80601 FRN of U.S. agent: 0033701590 Email address of U.S. agent: [email protected] UUX GROUP INC acknowledges their obligation to accept service of process on behalf of WINSTARS TECHNOLOGY LTD. WINSTARS TECHNOLOGY LTD with the FRN 0035614775 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature TANG MingJia engineer WINSTARS TECHNOLOGY LTD Signature Jack Fu Manager UUX GROUP INC 48_[model] US_Agent_2.911(d)(7) - U, V05

Page 1 of 4 FCC ID: 2BHA2-LEAPMR15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. EUT Constructional Details External EUT Photo Photo 1 Photo 2 Page 2 of 4 FCC ID: 2BHA2-LEAPMR15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 3 Photo 4 Page 3 of 4 FCC ID: 2BHA2-LEAPMR15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 5 Photo 6 Page 4 of 4 FCC ID: 2BHA2-LEAPMR15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 7 ---The End---

Label Size: L45mm * W30mm 1. The label is silk-screen on the sample USB-C Desktop Magnetic Wireless Charger Model Name: Leap MR15 FCC ID: 2BHA2-LEAPMR15 L W

Page 1 of 5 FCC ID: 2BHA2-LEAPMR15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. EUT Constructional Details Internal EUT Photo Photo 1 Photo 2 Antenna Page 2 of 5 FCC ID: 2BHA2-LEAPMR15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 3 Photo 4 Page 3 of 5 FCC ID: 2BHA2-LEAPMR15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 5 Photo 6 Page 4 of 5 FCC ID: 2BHA2-LEAPMR15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 7 Photo 8 Page 5 of 5 FCC ID: 2BHA2-LEAPMR15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Photo 9 Photo 10 ------End------

Page 1 of 14 Report No.: AITSZ24052210W3 RF Exposure Evaluation Client Information: Applicant: WINSTARS TECHNOLOGY LTD Applicant add.: 1-5,No.5,Taisong Industrial Zone, DalangCommunity,Dalang Street,Longhua District, ShenZhen Manufacturer: WINSTARS TECHNOLOGY LTD Manufacturer add.: 1-5,No.5,Taisong Industrial Zone, DalangCommunity,Dalang Street,Longhua District, ShenZhen Product Information: Product Name: USB-C Desktop Magnetic Wireless Charger Model No.: Leap MR15 Brand Name: Minthouz Test samples.: AITSZ24052210-1 FCC ID: 2BHA2-LEAPMR15 Applicable standards: FCC CFR 47 PART 1, § 1.1310 KDB 680106 D01 Wireless Power Transfer v04 Prepared By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Date of Receipt: May 22, 2024 Date of Test: May 22, 2024 ~ Jun 25, 2024 Date of Issue: Jun 25, 2024 Test Result: Pass This device described above has been tested by Guangdong Asia Hongke Test Technology Limited and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Note: This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited, this document may be altered or revised by Guangdong Asia Hongke Test Technology Limited, personal only, and shall be noted in the revision of the document. This test report must not be used by the client to claim product endorsement. Reviewed by: Approved by: Leon.yi Sean She Page 2 of 14 Report No.: AITSZ24052210W3 1 CONTENTS COVER PAGE Page 1 CONTENTS 2 2 TEST FACILITY 4 2.1 Deviation from standard 4 2.2 Abnormalities from standard conditions 4 2.3 Test Location 4 3 GENERAL INFORMATION 5 4 TEST METHODOLOGY 6 4.1 Measuring Standard 6 4.2 Requirements 6 4.3 Limits 6 4.4 Test Setup 7 4.5 Test Procedure 7 5 Equipment Approval Considerations 8 5.1 Description of the test mode 9 5.2 Peripheral List 9 5.3 Test Instruments list 9 5.4 Duty Cycle 10 5.5 Test Result 11 1.1 Test Setup photo 12 Page 3 of 14 Report No.: AITSZ24052210W3 Revision History Revision Issue Date Revisions Revised By 00 Jun 25, 2024 Initial Issue Sean She Page 4 of 14 Report No.: AITSZ24052210W3 2 TEST FACILITY The test facility is recognized, certified or accredited by the following organizations: FCC-Registration No.: 251906 Designation Number: CN1376 Guangdong Asia Hongke Test Technology Limited has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. IC —Registration No.: 31737 CAB identifier: CN0165 The 3m Semi-anechoic chamber of Guangdong Asia Hongke Test Technology Limited has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 31737 A2LA-Lab Cert. No.: 7133.01 Guangdong Asia Hongke Test Technology Limited has been accredited by A2LA for technical competence in the field of electrical testing, and proved to be in compliance with ISO/IEC 17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirements in the identified field of testing. 2.1 Deviation from standard None 2.2 Abnormalities from standard conditions None 2.3 Test Location Guangdong Asia Hongke Test Technology Limited Address: B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Page 5 of 14 Report No.: AITSZ24052210W3 3 GENERAL INFORMATION EUT Name: USB-C Desktop Magnetic Wireless Charger Model No: Leap MR15 Serial Model: CW101,CW101-ZX,Leap MR15-ZX Test sample(s) ID: AITSZ24052210-1 Sample(s) Status: Engineer sample Operation frequency: 113kHz-205kHz Modulation Technology: ASK Antenna Type: Loop coil Antenna Antenna gain: 0dBi Power supply: Input: 5V⎓3A,9V⎓2.22A,12V⎓1.67A Output: 15W Adapter: Model:QLO20P-VC Input:100-240V~ 50/60Hz 0.5A Output:5V⎓3A/9V⎓2.22VA/12V⎓1.67A 20W Max Model different: Different model names Note: For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. Page 6 of 14 Report No.: AITSZ24052210W3 4 TEST METHODOLOGY 4.1 Measuring Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1091 RF exposure is calculated. According KDB680106 D01: KDB 680106 D01 Wireless Power Transfer v04. 4.2 Requirements According to the item 3 of KDB 680106 D01v04: Inductive wireless power transfer applications that meet all of the following requirements are excluded from submitting an RF exposure evaluation. (1) Mobile Device and Portable Device Configurations (2) Equipment Authorization Procedures for Devices Operating at Frequencies Below 4 MHz (3) The aggregate H-field strengths anywhere at or beyond 15 cm surrounding the device, and 20 cm away from the top surface. 4.3 Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Page 7 of 14 Report No.: AITSZ24052210W3 4.4 Test Setup 4.5 Test Procedure 1) The RF exposure test was performed in anechoic chamber. 2) The measurement probe was placed at test distance (15 cm from all sides and 20 cm from the top) which is between the edge of the charger and the geometric center of probe. 3) The highest emission level was recorded and compared with limit as soon as measurement of each points (A, B, C, D, E,F) were compl…

Text truncated - open the document above for the full version.

Page 1 of 22 Report No.: AITSZ24052210W2 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. FCC TEST REPORT Client Information: Applicant: WINSTARS TECHNOLOGY LTD Applicant add.: 1-5,No.5,Taisong Industrial Zone, DalangCommunity,Dalang Street,Longhua District, ShenZhen Manufacturer: WINSTARS TECHNOLOGY LTD Manufacturer add.: 1-5,No.5,Taisong Industrial Zone, DalangCommunity,Dalang Street,Longhua District, ShenZhen Product Information: Product Name: USB-C Desktop Magnetic Wireless Charger Model No.: Leap MR15 Brand Name: Minthouz FCC ID: 2BHA2-LEAPMR15 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Prepared By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Date of Receipt: May 22, 2024 Date of Test: May 22, 2024 ~ Jun 25, 2024 Date of Issue: Jun 25, 2024 Test Result: Pass This device described above has been tested by Guangdong Asia Hongke Test Technology Limited and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Note: This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited, this document may be altered or revised by Guangdong Asia Hongke Test Technology Limited, personal only, and shall be noted in the revision of the document. This test report must not be used by the client to claim product endorsement. Reviewed by: Approved by: Leon.yi Sean she Page 2 of 22 Report No.: AITSZ24052210W2 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. 1 Contents Page COVER PAGE 1 CONTENTS ........................................................................................................................................................... 2 2 TEST SUMMARY .................................................................................................................................................. 5 2.1 STATEMENT OF THE MEASUREMENT UNCERTAINTY ............................................................................................. 5 2.2 MEASUREMENT UNCERTAINTY ............................................................................................................................ 5 3 TEST FACILITY ..................................................................................................................................................... 6 3.1 DEVIATION FROM STANDARD ............................................................................................................................... 6 3.2 ABNORMALITIES FROM STANDARD CONDITIONS .................................................................................................... 6 3.3 TEST LOCATION ................................................................................................................................................. 6 4 GENERAL INFORMATION ................................................................................................................................... 7 4.1 EUT TEST MODE ............................................................................................................................................... 8 4.2 DESCRIPTION OF TEST SETUP............................................................................................................................. 8 4.3 PERIPHERAL LIST ............................................................................................................................................... 9 4.4 EUT PERIPHERAL LIST ....................................................................................................................................... 9 5 EQUIPMENTS LIST FOR ALL TEST ITEMS ..................................................................................................... 10 6 CONDUCTED EMISSION TEST ......................................................................................................................... 11 6.1 CONDUCTED EMISSION MEASUREMENT ................................................................................................ 11 6.2 POWER LINE CONDUCTED EMISSION LIMITS ........................................................................................... 11 6.3 TEST PROCEDURE ...................................................................................................................................... 11 6.4 DEVIATION FROM TEST STANDARD ......................................................................................................... 11 6.5 TEST SETUP ................................................................................................................................................. 12 6.6 EUT OPERATING CONDITIONS .................................................................................................................. 12 6.7 TEST RESULT .................................................................................................................................................. 13 7 RADIATED EMISSION MEASUREMENT .......................................................................................................... 15 7.1 RADIATED EMISSION LIMITS .............................................................................................................................. 15 7.2 ANECHOIC CHAMBER TEST SETUP DIAGRAM ..................................................................................................... 16 7.3 TEST PROCEDURE ...........................................................................…

Text truncated - open the document above for the full version.

ShenzhenWINSTARSElectronicsCo.,Ltd. Address:TEL:755-88823721,Building4,TaisongIndustrialPark, DalangStreet,Longhua,Shenzhen SampleAcknowledgment Internalpagelist：ElectricalschematicdiagramSampledesigndrawings Suppliersampletestinspectionreport EnvironmentalreportDescriptionoftransportpackaging modeMaterialdescriptionreport Theaboveisfilledbythesupplier,andthefollowingisfilledbyXinboyueCompany. Confirmreason:NewmaterialDesignalteration Backupsupplierother Submittedby:Severalapplications： Material determi QualityEngineering Researchand development Sign sample Remarks DocumentNo: WINSTARSTemporary No: WINSTARSMaterialNo: 2.99.1.00035 materialname： wirelesschargingcoil Materialspecification： wirelesschargingcoilwirelesschargingcoil10TS6.5uHmulti- strandenameledwirewithwhiteadhesiveleadhightemperature adhesiveisolationmagneticsheet42.5±0.5lead8MMtin immersion2MM Supplierpartnumber： H13701 Supplierspecification: 20.5*40*0.08*100P*10TS+G42.5 wirelesschargingcoil2.99.1.00035 Samplequantity： 5pcs SupplierName: DongGuanHonourElectronicCo.,Ltd Supplier'sAddressn: 2/F,Building1,182Xi'anRoad,Chang'anTown,DongguanCity Contact/Tel: ZhengCaiqin/13602309176 ManufacturerName： DongGuanHonourElectronicCo.,Ltd nation Quali fied Exami ne Exami ne Exami ne Unqu alified CheckCheckCheck ProductSpecification ModelH13701 Version/Ver.A/0 Pages/Page2/3 CustomerNumber CustomerCode H137 Name ProductName Wirelesschargingcoil2.99.1.00035 Product specifications Specification 20.5*40*0.08*100P*10TS+G42.5 Windingdirection WindingDirection CCW Documentissuerecord Version/Ver.ModifyDesc.IssueDate A/0First Line 2024/4/30 DongGuanHonourElectronicCo.,Ltd. ProdctTypeWireless charging coil VersionA DocumentNumberDocumentCode:HN-PE-007 ProductSpecification ModelH13701 VersionA/0 Page3/3 CustomerCode H137 ProductName Wireless chargingcoil 2.99.1.00035 Product Specification 20.5*40*0.08*100P*10TS+G42.5 WindingDirection CCW 1.ProductSize(Unit:MM) ItemsSizeTol. A20.5±0.5 B40.0±0.5 C42.5±0.8 D8.0±2.0 E2.0±1.0 F(excluding citation Thicknessat line) 2.2max Remarks: 1. Coilcrossoutgoingline, outgoinglinedispensingfixed non-divergentline 2.Themiddlepaste20*1.0smalldisc 3. Thepositionofthecoillead grooveisseparatedbyhigh- temperatureglue. 2.SCHEMATIC 3.windingparametersWindingSpecification: NO.WireWireODTurnsLayerLayer 1SF0.08*100PEnameledStrand10TS1 4.Electricalcharacteristics NO. Properties Test conditions Value Unit TOL Tester 1 LS 100KHZ/1 V 6.5 μH 10%TH2830 2 DCR @25°C 60 mΩ MaxTH2516 3 Qvalue 100KHZ/1 V 90 mΩ MinTH2830 5.Materiallist NO.Material Spec. 1EnamelledStrand 0.08*100P 2G42.5FerriteHardMagneticDoubleSlotSingleHole 42.5*5.3*0.8 3ferritesmalldisc Φ20*1.0 4Single-earsingle-slotordinarydouble-sidedadhesive 41*7*0.05 5Teahightemperaturetape N/A 6hightemperaturetin eco-friendlyhightemperaturetin DongGuanHonourElectronicCo.,Ltd. ProdctTypeWireless chargingcoil DongGuanHonourElectronicCo.,Ltd. DocumentNumberDocumentCode:HN-PE-007

Page 1 of 2 FCC ID: 2BHA2-LEAPMR15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Test Setup Photo DCD Conduction Radiation (9KHz-30MHz) Page 2 of 2 FCC ID: 2BHA2-LEAPMR15 Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. Radiation (30MHz-1000MHz) ------End------