2BHBL-BG7PROP-7 Pro Professional HD GNSS Receiver

• Power on: Always on Parts Description Power Lamp Bluetooth Lamp 12 CAUTION GB Thank you for choosing our product. This manual is intended to guide you through the safe and correct use of the product and its accessories, avoiding improper operations that may result in injury of yourself or any other person or cause device damage. As a precision electronics, the product contains no component that can be repaired by your own. Any attempt to disassemble the product will void the original manufacturer's warranty. The protection class of the external active antenna is IP66, which can work normally in all-weather environments such as rain, snow and high dust, but do not immerse the antenna completely in water. The main unit of the P-7 Pro is not waterproof. • Disconnected: off • Connected: always on Bluetooth LampPower Lamp SMA Connector (Female) SMA Connector (Male) USB Type-A C onnector External Active Antenna (Magnetic Mount) Professional HD GNSS Receiver 7 Quick Start Steps to Use Connect the P-7 Pro to the external active antenna, and tighten the antenna connector clockwise. Place the external active antenna in a position with a good view of the sky, such as the roof of the car, the top of the surveying pole. The main unit of the P-7 Pro is not waterproof. The placement of the antenna significantly affects the accuracy of the tracks. For more placement suggestions, please visit: cbgps.com/p7/q The positioning status of the satellite needs to be viewed on the terminal device. Connect to the Terminal Device The P-7 Pro supports two connection modes: wired and wireless. Both connection modes are supported to connect the device simultaneously. DEVICE 1 2 DEVICE 3 The operating systems and connection modes supported by the P-7 Pro are as follows: Linux USB SPP USB SPP USB SPP BLE USB OTG SPP/BLE BLE Plug the USB connector into the computer. Wired Connection Plug the USB connector into the mobile device via an OTG cable. 44 The P-7 Pro can be accessed by two programs simultaneously, and the parameters of the P-7 Pro can be configured through the Enhanced COM Port. When wired, it supports hardware-level dual serial ports: “Enhanced COM Port” and “Standard COM Port”. How to connect with terminal device please visit: ×× 2 1 cbgps.com/p7/q Connect with the power bank during portable use. Bluetooth Connection Connect with the car charger while driving. BLE 5.1 SPP 2.1 How to connect with the App, please visit: The P-7 Pro supports two Bluetooth protocols: BLE5.1 and SPP 2.1. cbgps.com/p7/q 55 The P-7 Pro supports applications for multiple platforms, please refer to the support page for usage. We will continuously update the list of supported App. 56 cbgps.com/p7/q How to Use the App Protection class External Active Antenna IP66 Operating temperature -20 to +50 °C °C / -4 °F to +122 °F Constellation GPS (L1+L5), GLONASS, Galileo (E1+E5a), QZSS (L1+L5), BeiDou, IRNSS (L5), SBAS Accuracy * Vertical: 15m Horizontal: 0.5m/CEP(50%), 1.5m/CEP(95%) Acquisition time * Reacquisition: <2s, Cold start: <34s Output sentences Baud Rate (Default): 57,600bps Messages: GNRMC, GNGGA, GNGSV, GNGSA (Default); GNGLL, GNVTG (Optional) Protocol: NMEA-0183 Geodesics WGS84 Update rate 1Hz (Default), 5Hz Bluetooth SPP 2.1 BLE 5.1 Connectors Antenna connectors: SMA USB device: USB 2.0 Type-A Power consumption Main unit: DC 5V / 100mA Antenna: DC 3.3V / 20mA Dimensions (WxHxD) Main unit: 65×18×10mm / 2.6×0.7×0.4in Antenna feeder: 300cm / 9.8feet Weight Main unit: 21g / 0.74oz Antenna: 80g / 2.8oz * The test was done outdoor, in an open area. On content unmentioned in the instruction, please visit the official website at any time to learn about the latest use skill and information. Specifications ± Trademark Other product and company names mentioned herein may be trademarks or trade names of their respective owners. is a trademark of Victory Co., Ltd. Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of VICTORY is prohibited. Under no circumstances shall VICTORY be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused. App Store Google Play FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Consult the dealer or an experienced radio/TV technician for help. • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 78 59 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. Caution: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

Fuzhou Victory Technology CO.,LTD Floor 15,11#Yijing Garden, Fufei RD., Fuzhou, Fujian. China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-7-3 To whom it may concern: We, Fuzhou Victory Technology CO.,LTD, hereby certify that the equipment for which authorization is sought (FCC ID: 2BHBL-BG7PRO) is not “covered” equipment prohibited from receiving an equipment authorization pursuant to § 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing “covered” equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, {新申请人签名} Signature Lu Wang Manager Fuzhou Victory Technology CO.,LTD 62_[model] CoveredEqu_2.911(d)(5)(i) and (ii) - U, V03

Fuzhou Victory Technology CO.,LTD Floor 15,11#Yijing Garden, Fufei RD., Fuzhou, Fujian. China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-7-3 U.S. Agent Designation Fuzhou Victory Technology CO.,LTD acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BHBL-BG7PRO): Name and company of U.S. agent: ACT Lab LLC Physical U.S. address of agent: 3280 East 59th Street Long Beach, CA 90805 United States FRN of U.S. agent: 0033465568 Email address of U.S. agent: [email protected] ACT Lab LLC acknowledges their obligation to accept service of process on behalf of Fuzhou Victory Technology CO.,LTD. Fuzhou Victory Technology CO.,LTD with the FRN [0035617695] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission- related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Lu Wang Manager Fuzhou Victory Technology CO.,LTD {代理商签名} Signature Scott Huber Senior Technical Director ACT Lab LLC 48_[model] US_Agent_2.911(d)(7) - U, V05

Fuzhou Victory Technology CO.,LTD Add: Floor 15,11#Yijing Garden, Fufei RD., Fuzhou, Fujian. China Date: 2024-7-3 FCC ID: 2BHBL-BG7PRO Dear Sir/Madam, We, Fuzhou Victory Technology CO.,LTD Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model: Product name: P-7 Pro Professional HD GNSS Receiver Model no.: P-7 Pro, P-7 Pro SE, P-7 Pro Lite Sincerely, Name/Title： Lu Wang/Manager Company: Fuzhou Victory Technology CO.,LTD Address: Floor 15,11#Yijing Garden, Fufei RD., Fuzhou, Fujian. China Phone: +86 15060079099 Fax: N/A E-Mail: [email protected]

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2024-7-3> Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2BHBL-BG7PRO P-7 Pro For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title： Lu Wang/Manager Company: Fuzhou Victory Technology CO.,LTD Address: Floor 15,11#Yijing Garden, Fufei RD., Fuzhou, Fujian. China Phone: +86 15060079099 Fax: N/A E-Mail: [email protected]

Fuzhou Victory Technology CO.,LTD Floor 15,11#Yijing Garden, Fufei RD., Fuzhou, Fujian. China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-7-3 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2BHBL-BG7PRO including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins’ current valid General Terms and Conditions (AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title： Lu Wang/Manager Company: Fuzhou Victory Technology CO.,LTD Address: Floor 15,11#Yijing Garden, Fufei RD., Fuzhou, Fujian. China Phone: +86 15060079099 Fax: N/A E-Mail: [email protected]

FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Appendix III EUT External Photographs Photo 1 Appearance of EUT Photo 2 Appearance of EUT FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Photo 3 Appearance of EUT Photo 4 Appearance of EUT FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Photo 5 Appearance of EUT Photo 6 Appearance of EUT

FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Appendix I Label Appendix II Label Location FCC ID: 2BHBL-BG7PRO Model: P-7 Pro

FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Appendix IV EUT Internal Photographs Photo 7 Internal of EUT Photo 8 Appearance of PCB FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Photo 9 Appearance of PCB Photo 10 Appearance of PCB BT Antenna FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Photo 11 Appearance of PCB

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202404-0280-1 Page: 1 of 3 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 Maximum Permissible Exposure Evaluation FCC ID: 2BHBL-BG7PRO 1. General Information about EUT 1.1 Client Information Applicant : Fuzhou Victory Technology CO.,LTD Address : Floor 15,11#Yijing Garden, Fufei RD., Fuzhou, Fujian. China Manufacturer : Fuzhou Victory Technology CO.,LTD Address : Floor 15,11#Yijing Garden, Fufei RD., Fuzhou, Fujian. China 1.2 General Description of EUT (Equipment Under Test) EUT Name : P-7 Pro Professional HD GNSS Receiver Models No. : P-7 Pro, P-7 Pro SE, P-7 Pro Lite Model Different : All these models are identical in the same PCB, layout and electrical circuit, The only difference is model name, brand name and product name. Brand Name : Columbus Sample ID : HC-C-202406-0280-01-01 Product Description : Operation Frequency: Bluetooth&BLE: 2402MHz~2480MHz Antenna Gain: 4.3dBi Chip Antenna Power Rating : USB Input: DC 5V-1A Software Version : A0 Hardware Version : V1.0 Remark: The above antenna information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications, the laboratory shall not be held responsible. Report No.: TBR-C-202404-0280-1 Page: 2 of 3 TB-RF-074-1.0 SAR Test Exclusion Calculations 1. FCC: According to KDB 447498 D01 Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies v06. (1) Clause 4.3: General SAR test reduction and exclusion guidance Sub clause 4.31: Standalone SAR test exclusion considerations 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6GHz at test separation distance≤5 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√ f (GHz) ] ≤3.0 for 1-g SAR [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√ f (GHz) ] ≤7.5.0 for 10-g SAR 2. Summary simultaneous transmission for SAR Exclusion The SAR exemption limits outlined in clause 4.3.2(b) of KDB 447498 have been derived based on an approximate SAR value of 0.4 W/kg using half-wave dipole antennas Footnote 1. As such, when simultaneous transmitter SAR evaluations include transmitters that have been exempt from routine SAR evaluation, the SAR must be estimating based on the ratio between the maximum tune-up tolerance limit of the transmitter that has been exempt and the exemption limit at the specific distance and frequency for that transmitter. This ratio must be multiplied by 0.4 W/kg (2.0 W/kg for controlled use and 1.0 W/kg for limb worn devices) in order to calculate the estimated SAR level. The estimate SAR value is calculated based the following equation: (maximum power level including tune-up tolerance for transmitter A / maximum power level of exemption at the same frequency and distance) * 0.4W/kg The [∑ of (the highest measured or estimated SAR for each standalone antenna configuration, adjusted for maximum tune-up tolerance) / 1.6 W/kg] + [∑ of MPE ratios] is ≤ 1.0. The SAR to peak location separation ratios of all simultaneously transmitting antenna pairs operating in portable device exposure conditions are all ≤ 0.04, and the [∑ of MPE ratios] is ≤ 1.0. Report No.: TBR-C-202404-0280-1 Page: 3 of 3 TB-RF-074-1.0 3. Calculation: Test separation: 5mm Bluetooth Mode (GFSK) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2402 -6.252 -6±1 -5 0.316 0.098 3.0 2441 -6.177 -6±1 -5 0.316 0.099 3.0 2480 -5.496 -5±1 -4 0.398 0.125 3.0 Bluetooth Mode (π/4-DQPSK) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2402 -5.757 -5±1 -4 0.398 0.123 3.0 2441 -5.664 -5±1 -4 0.398 0.124 3.0 2480 -5.077 -5±1 -4 0.398 0.125 3.0 BLE 1M Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2402 -8.435 -8±1 -7 0.200 0.062 3.0 2440 -8.412 -8±1 -7 0.200 0.062 3.0 2480 -7.755 -7±1 -6 0.251 0.079 3.0 BLM 2M Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2402 -8.13 -8±1 -7 0.200 0.062 3.0 2440 -8.018 -8±1 -7 0.200 0.062 3.0 2480 -7.374 -7±1 -6 0.251 0.079 3.0 Conclusion: The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06. -----END OF REPORT-----

CA-C03 Specifications CA-C03_V01 1 SMD Antenna Specifications CrossAir TM SMD Antenna RoHS compliant PN: CA-C03 2.4 GHz ISM Band Antenna Guangzhou Cambrian electronic Technology Co., LTD No. 410, Building D2, Luogang Agile Plaza, Shui West Road, Science City, Huangpu District, Guangzhou CA-C03 Specifications CA-C03_V01 2 Features 1. Small size SMD patch antenna with size only 5.5 X 2.0 X 1.0 mm. 2. Low energy loss, high antenna efficiency. 3. High stability under temperature and humidity changes. Structure 1. Antenna feeder 2. Feeder identification mark 3. Antenna welding fixed end Size Three ViewsymbolSize(mm) L 5.5±0.1 w 2.0±0.1 T 1.0±0.1 a 0.5±0.1 CA-C03 Specifications CA-C03_V01 3 Electrical Characteristics CA-C03 Specification Working Frequency 2450±50MHz Initial frequency band(GHz) 2.7GHz Band Width >100MHz Impedance 50Ω Gain(dBi) 4.3（peak） VSWR <2 Operation Temperature -40°C~+95°C Power Capacity 3W Antenna Pad and Trace Design Design dimension drawing CA-C03 Specifications CA-C03_V01 4 Match device value Series 1 0Ω Shunt 1 3nh Series 2 0Ω Antenna test on test board (board thickness 1.0mm) CA-C03 Specifications CA-C03_V01 5 Antenna S11 Characteristics Antenna VSWR Characteristics CA-C03 Specifications CA-C03_V01 6 Gain and across Bandwidth 2.4G-2.5GHz Peak Gain 4.3dBi Average Gain across the band 4.1dBi Gain Range across the band 3.9dBi~4.3dBi Peak Efficiency 81.7% Average Efficiency acro ss the band 80.2% Efficiency Range across the band 78.6%~81.7% Theta @2.45 GHz Z Y X Efficiency and Radiation Patterns CA-C03 Specifications CA-C03_V01 7 Phi @2.45 GHz Total @2.45 GHz Welding conditions As shown below: CA-C03 Specifications CA-C03_V01 8 Package Plastic carrier tape specifications Index Ao Bo ΦD T W Dimension (mm) 3.0±0.1 6.0±0.1 1.55±0.05 1.2±0.1 11.8±0.1 Index E F Po P1 P2 Dimension (mm) 1.75±0.1 4.6±0.1 4.0±0.1 4.0±0.1 2.0±0.1 Reel size CA-C03 Specifications CA-C03_V01 9 Index A B C Dimension(mm) 178 60 13.5 Storage Environment The following conditions should be met when the product is stored: Temperature : -10°C~+40°C Humidity : 30% to 70% relative humidity The location where the product is placed should not be exposed to corrosive gases such as sulfur. The product should be placed in a tool box and protected from moisture and dust. Products should be stored in warehouses away from heat, vibration, and direct sunlight. Product should be stored under airtight conditions.

Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202404-0280-2 Page: 1 of 39 FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 RF Test Data for Bluetooth LE (Conducted Measurements) General Description of EUT Product Name: P-7 Pro Professional HD GNSS Receiver Test Model: P-7 Pro Sample ID: HC-C-202406-0280-01-01 Environmental Conditions Temperature: 24.2°C Relative Humidity: 52.2% Test Voltage: DC 5V Test Engineer: Jolin Lee Note: For a more detailed features description, please refer to the report TBR-C-202404-0280-2 The report only show the worst case data. Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202404-0280-2 Page: 2 of 39 FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Contents 1. Duty Cycle ........................................................................................................................................................................................... 3 2. Maximum Conducted Output Power ................................................................................................................................................. 7 3. -6dB Bandwidth ................................................................................................................................................................................ 11 4. Occupied Channel Bandwidth ......................................................................................................................................................... 15 5. Maximum Power Spectral Density Level ......................................................................................................................................... 19 6. Band Edge ........................................................................................................................................................................................ 23 7. Conducted RF Spurious Emission .................................................................................................................................................. 28 8. Restrict Band .................................................................................................................................................................................... 35 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202404-0280-2 Page: 3 of 39 FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 1. Duty Cycle Condition Mode Frequency (MHz) Antenna Duty Cycle (%) Correction Factor (dB) 1/T (kHz) NVNT BLE 1Mbps 2402 Ant1 84.8 0.72 0.47 NVNT BLE 1Mbps 2440 Ant1 85.2 0.7 0.47 NVNT BLE 1Mbps 2480 Ant1 85.2 0.7 0.47 NVNT BLE 2Mbps 2402 Ant1 42.8 3.69 0.93 NVNT BLE 2Mbps 2440 Ant1 42.8 3.69 0.93 NVNT BLE 2Mbps 2480 Ant1 42.8 3.69 0.93 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202404-0280-2 Page: 4 of 39 FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Test Graphs Duty Cycle NVNT BLE 1Mbps 2402MHz Ant1 Duty Cycle NVNT BLE 1Mbps 2440MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202404-0280-2 Page: 5 of 39 FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Duty Cycle NVNT BLE 1Mbps 2480MHz Ant1 Duty Cycle NVNT BLE 2Mbps 2402MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202404-0280-2 Page: 6 of 39 FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Duty Cycle NVNT BLE 2Mbps 2440MHz Ant1 Duty Cycle NVNT BLE 2Mbps 2480MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202404-0280-2 Page: 7 of 39 FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 2. Maximum Conducted Output Power Condition Mode Frequency (MHz) Antenna Total Power (dBm) Limit (dBm) Verdict NVNT BLE 1Mbps 2402 Ant1 -8.435 30 Pass NVNT BLE 1Mbps 2440 Ant1 -8.412 30 Pass NVNT BLE 1Mbps 2480 Ant1 -7.755 30 Pass NVNT BLE 2Mbps 2402 Ant1 -8.13 30 Pass NVNT BLE 2Mbps 2440 Ant1 -8.018 30 Pass NVNT BLE 2Mbps 2480 Ant1 -7.374 30 Pass Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202404-0280-2 Page: 8 of 39 FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Test Graphs Power NVNT BLE 1Mbps 2402MHz Ant1 Power NVNT BLE 1Mbps 2440MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202404-0280-2 Page: 9 of 39 FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Power NVNT BLE 1Mbps 2480MHz Ant1 Power NVNT BLE 2Mbps 2402MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202404-0280-2 Page: 10 of 39 FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 Power NVNT BLE 2Mbps 2440MHz Ant1 Power NVNT BLE 2Mbps 2480MHz Ant1 Shenzhen Toby Technology Co., Ltd. Http://www.tobylab.cn Add：1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. Report No.: TBR-C-202404-0280-2 Page: 11 of 39 FCC ID: 2BHBL-BG7PRO TB-RF-074-1.0 3. -6dB Bandwidth Condition Mode Frequency (MHz) Antenna -6 dB Bandwidth (MHz) Limit -6 …

Text truncated - open the document above for the full version.

Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202404-0280-2 Page: 1 of 34 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 Radio Test Report FCC ID: 2BHBL-BG7PRO Report No. : TBR-C-202404-0280-2 Applicant : Fuzhou Victory Technology CO.,LTD Equipment Under Test (EUT) EUT Name : P-7 Pro Professional HD GNSS Receiver Model No. : P-7 Pro Series Model No. : P-7 Pro SE, P-7 Pro Lite Brand Name : Columbus Sample ID : HC-C-202406-0280-01-01&HC-C-202406-0280-01-02 Receipt Date : 2024-06-21 Test Date : 2024-06-21 to 2024-07-09 Issue Date : 2024-07-09 Standards : FCC Part 15 Subpart C 15.247 Test Method : ANSI C63.10: 2013 KDB 558074 D01 15.247 Meas Guidance v05r02 Conclusions : PASS In the configuration tested, the EUT complied with the standards specified above. Test By : Jolin Lee Reviewed By : Henry Huang Approved By : Ivan Su This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in the report. Report No.: TBR-C-202404-0280-2 Page: 2 of 34 TB-RF-074-1.0 Contents CONTENTS ............................................................................................................................................ 2 1. GENERAL INFORMATION ABOUT EUT ............................................................................. 5 1.1 Client Information ................................................................................................................ 5 1.2 General Description of EUT (Equipment Under Test) ................................................... 5 1.3 Block Diagram Showing the Configuration of System Tested ...................................... 6 1.4 Description of Support Units .............................................................................................. 7 1.5 Description of Test Mode ................................................................................................... 7 1.6 Description of Test Software Setting ................................................................................ 8 1.7 Measurement Uncertainty .................................................................................................. 8 1.8 Test Facility........................................................................................................................... 9 2. TEST SUMMARY..................................................................................................................... 10 3. TEST SOFTWARE .................................................................................................................. 10 4. TEST EQUIPMENT AND TEST SITE .................................................................................. 11 5. CONDUCTED EMISSION ...................................................................................................... 12 5.1 Test Standard and Limit ................................................................................................... 12 5.2 Test Setup........................................................................................................................... 12 5.3 Test Procedure .................................................................................................................. 12 5.4 Deviation From Test Standard......................................................................................... 13 5.5 EUT Operating Mode ......................................................................…

Text truncated - open the document above for the full version.