2BHCG-712818STAND3-IN-1 WIRELESS CHARGING STAND

3 - IN - 1 WIRELESS CHARGING STAND User Manual PRODUCT OUTLINE • If magnetic wireless charging panel and earbud panel both in charging, the indicator light change into blue. • It is highly recommended to charge your watch when the watch is around 10% power, if you use out of all power, charging will be much slower, you need to have patience for wait! FCC INSTRUCTION This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation." CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. Distributed by: ALDI Inc. Batavia, IL 60510 www.ALDI.us Contact: [email protected] (US)1-888-204-0934 Specifications Input voltage: 5V/3A 9V/3A(QC) Output power: • Magnetic mobile phone charging panel: max 15W/10W/ 7.5W/5W • Earbud charging panel: max 5W • iWatch charging panel: max 2.5W Charging efficiency: 70%-80% Standard Accessories 1* Multifunctional Wireless Charger 1* USB type C Cable 1* User Manual 1* Magnet adhesive Ring Attention 1.Please keep the charger away from water or other liquid. 2. If you need to clean the charger, please make sure it is power off. 3. Using Environment temperature remain 1-45 degree Applicable Devices 1. Devices with built-in quick charge/normal charge wireless receiver. 2. Devices with outer-face wireless charging receiver. Usage Instructions 1. Connect the wireless charger to the AC power supply through the power adapter(adapter not included) and a type C charging cable(included), the wireless charger enters the standby mode, the indicator light keeps in red. ***The mobile Phone wireless charging panel is magnetic, if your mobile phone support wireless charging, but without Magsafe, you can stick the Magnet Ring (one piece included) onto your mobile phone wireless charging area, this ring help suck your phone onto the mobile Phone wireless charging panel, then you can charging on the panel. • Take off the magnet ring adhesive cover, and stick onto correct charging area, press to stick and do not move in hours to stick firmly. • Magnet Ring cannot be steady stick onto glass surface, if your phone is glass surface you can have a flat thin phone case in other material, and adhesive the ring onto the phone case. 2.Place your device vertically or horizontally in the center of the Wireless Changer until your device begins to charge, the indicator light keeps in Red&Blue. Thanks for purchasing our multifunctional wireless charger SOPORTE DE CARGA INALÁMBRICO 3 EN 1 Manual del usuario DESCRIPCIÓN DEL PRODUCTO • Si el panel magnético de carga inalámbrica y el panel de auriculares están en el proceso de carga, la luz indicadora cambia a azul. • Es muy recomendable que cargue su reloj cuando tenga alrededor del 10 % de energía; si lo usa hasta dejarlo sin energía, la carga será mucho más lenta, ¡y tendrá que tener paciencia! Especificaciones Voltaje de entrada: 5V/3A 9V/3A(QC) Potencia de salida: • Panel magnético de carga para teléfono celular: 15 W/10W/ 7.5 W/5 W como máximo • Panel de carga de auriculares: 5 W como máximo • Panel de carga de iWatch: 2.5 W como máximo Eficiencia de carga: 70 % - 80 % Accesorios estándar 1* Cargador inalámbrico multifuncional 1* Cable USB tipo C 1* Manual de usuario 1* Anillo adhesivo magnético Atención 1. Cargador alejado del agua u otros líquidos. 2. Si necesita limpiar el cargador, asegúrese de que esté apagado. 3. La temperatura ambiente de uso debe estar entre 1 y 45 Dispositivos que se pueden utilizar 1. Dispositivos con receptor integrado de carga inalámbrica rápida/carga normal. 2. Dispositivos con receptor externo de carga inalámbrica. Instrucciones de uso 1. Conecte el cargador inalámbrico a la fuente de alimentación de CA mediante el adaptador de corriente (adaptador no incluido) y un cable de carga tipo C (incluido). El cargador inalámbrico entra en modo de espera y la luz indicadora se mantiene en rojo. ***El panel de carga inalámbrica para teléfono celular es magnético. Si su teléfono celular soporta la carga inalámbrica, pero no tiene el sistema Magsafe, puede pegar el anillo magnético (uno incluido) en el área de carga inalámbrica de su teléfono celular; este anillo ayuda a mantener su teléfono en el panel de carga inalámbrica para teléfono celular, y de esta forma puede cargarlo. • Quite la cubierta adhesiva del anillo magnético y pegue el anillo en la zona de carga correcta, presione para pegarlo y no lo mueva durante algunas horas para que se pegue bien. • El anillo magnét…

Text truncated - open the document above for the full version.

ShenzhenHudsonTechnologyCo.,Ltd. U.S.AgentDesignationforServiceofProcess (ApplicantandU.S.AgentareSeparateParties) TO:FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046,USA ATTENTION:FCCCertification–Section2.911(d)(7)Information DesignatedU.S.Agent CompanyName:XtremeTimeInc. FRN:0035694579 ContactName:NATPHOPIN Address:1565UnionAve.UnionNJ7083,UnitedStates TelephoneNo:(212)502-0025 Email:[email protected] Thisletteristoconfirmthatwe(XtremeTimeInc.)haveacceptedtheresponsibilitytoactas theDesignatedU.S.AgentforServiceofProcessasrequiredbysection47CFR2.911(d)(7) onbehalfoftheApplicantnotedbelow. U.S.AgentSignature: Date:2024-07-24 Signedby(PrintedName/Title):NATPHOPIN/Manager TheApplicantacknowledgesthattheymustmaintainanagentfornolessthanoneyearafter terminatingallmarketingandimportationORtheconclusionofanyCommission-related proceedinginvolvingtheequipment.Theapplicantfurtheracknowledgestheirresponsibility toinformtheFCCwhenevertheDesignatedU.S.Agentinformationabovechanges. ShenzhenHudsonTechnologyCo.,Ltd. Applicant Companyname:ShenzhenHudsonTechnologyCo.,Ltd. FRN:0035625359 FCCID:2BHCG-712818STAND ContactName:PeterZhao Address:RM409,LvKaiBuilding,71Zone,XindongXin'anStreet,BaoanDistrict,Shenzhen, China518100 TelephoneNo:18823849960 Email:[email protected] ApplicantSignature: Date:2024-07-24 Signedby(PrintedName/Title):PeterZhao/Manager

Shenzhen Hudson Technology Co., Ltd. 2024.08.05 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for FCC ID: 2BHCG-712818STAND [Shenzhen Hudson Technology Co., Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, (Applicant signature) (Applicant printed name) Peter Zhao Shenzhen Hudson Technology Co., Ltd. 2024.08.05 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for FCC ID: 2BHCG-712818STAND [Shenzhen Hudson Technology Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Peter Zhao

Shenzhen Hudson Technology Co., Ltd. 2024.08.05 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: CONFIDENTIALITY REQUEST FOR EUT NAME: 3-IN-1 WIRELESS CHARGING STAND Trademark: MODEL : 712818 FCC ID : 2BHCG-712818STAND To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the - Block Diagram - Schematics - Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Client’s signature: Client’s name / title : Peter Zhao / Manager Contact information / address: RM409, LvKai Building, 71 Zone, Xindong Xin'an Street, Baoan District, Shenzhen, China 518100

Shenzhen Hudson Technology Co., Ltd. 2024.08.05 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen BCTC Testing Co., Ltd to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Client’s signature: Client’s name / title : Peter Zhao / Manager Contact information / address: RM409, LvKai Building, 71 Zone, Xindong Xin'an Street, Baoan District, Shenzhen, China 518100

Report No.: BCTC2406629509E External Photos Report No.: BCTC2406629509E Report No.: BCTC2406629509E Report No.: BCTC2406629509E

Size:60*30mm 3-IN-1 WIRELESS CHARGING STAND FCC ID: 2BHCG-712818STAND This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Label location

Report No.: BCTC2406629509E Internal Photos Antenna Phone Antenna Watch Antenna Earphone Report No.: BCTC2406629509E Report No.: BCTC2406629509E Report No.: BCTC2406629509E Report No.: BCTC2406629509E

No.：BCTC/RF-EMC-005 Page 1 of 11 Edition：B.2 TEST REPORT Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2406629509-2E Applicant: Shenzhen Hudson Technology Co., Ltd. Product Name: 3-IN-1 WIRELESS CHARGING STAND Test Model: 712818 Tested Date: 2024-06-18 to 2024-06-27 Issued Date: 2024-06-28 Report No.: BCTC2406629509-2E No.：BCTC/RF-EMC-005 Page 2 of 11 Edition：B.2 FCC ID: 2BHCG-712818STAND The test report is effective only with both signature and specialized stamp. This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full. The tested sample(s) and the sample information are provided by the client. Product Name: 3-IN-1 WIRELESS CHARGING STAND Trademark: Model/Type reference: 712818 Prepared For: Shenzhen Hudson Technology Co., Ltd. Address: RM409, LvKai Building, 71 Zone, Xindong Xin'an Street, Baoan District, Shenzhen, China 518100 Manufacturer: Shenzhen Hudson Technology Co., Ltd. Address: RM409, LvKai Building, 71 Zone, Xindong Xin'an Street, Baoan District, Shenzhen, China 518100 Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China. Sample Received Date: 2024-06-18 Sample tested Date: 2024-06-18 to 2024-06-27 Issue Date: 2024-06-28 Report No.: BCTC2406629509-2E Test Standards: FCC CFR 47 part1, 1.1307(b), 1.1310 KDB 680106 D01 Wireless Power Transfer v04 Test Results: PASS Tested by: Approved by: Lei Chen/Project Handler Zero Zhou/Reviewer Report No.: BCTC2406629509-2E No.：BCTC/RF-EMC-005 Page 3 of 11 Edition：B.2 Table Of Content Test Report Declaration Page 1. Version .................................................................................................................. 4 2. Product Information ............................................................................................... 5 2.1 Product Information ............................................................................................... 5 2.2 Support Equipment ............................................................................................... 5 2.3 Test Mode ............................................................................................................. 5 3. Test Facility And Test Instrument Used ................................................................. 6 3.1 Test Facility ........................................................................................................... 6 3.2 Test Instrument Used ............................................................................................ 6 4. Method Of Measurement ....................................................................................... 7 4.1 Applicable Standard .............................................................................................. 7 4.2 Block Diagram Of Test Setup ................................................................................ 7 4.3 Limit ...................................................................................................................... 8 4.4 Test procedure ...................................................................................................... 8 4.5 Equipment Approval Considerations ..................................................................... 9 4.6 E and H field Strength ........................................................................................... 9 5. Photographs Of Test Set-Up ............................................................................... 10 (Note: N/A Means Not Applicable) Report No.: BCTC2406629509-2E No.：BCTC/RF-EMC-005 Page 4 of 11 Edition：B.2 1. Version Report No. Issue Date Description Approved BCTC2406629509-2E 2024-06-28 Original Valid Report No.: BCTC2406629509-2E No.：BCTC/RF-EMC-005 Page 5 of 11 Edition：B.2 2. Product Information 2.1 Product Information Model/Type Reference: 712818 Model Differences: N/A Hardware Version: N/A Software Version: N/A Operation Frequency: Wireless charging Output (Phone/ Earphone): 115kHz-205kHz, Wireless charging Output (Watch): 300-350kHz Type of Modulation: ASK Antenna installation: loop coil antenna Ratings: Input: DC 5V/3A, 9V/3A Wireless charging Output (Phone): 5W/7.5W/10W/15W Wireless charging Output (Earphone): 5W Wireless charging Output (Watch): 2.5W 2.2 Support Equipment No. Device Type Brand Model Series No. Note E-1 3-IN-1 WIRELESS CHARGING STAND 712818 N/A EUT E-2 Adapter N/A CD122 N/A Auxiliary E-3 Dummy load N/A DL02 N/A Auxiliary E-4 Dummy load N/A DL01 N/A Auxiliary E-5 Dummy load N/A DL01 N/A Auxiliary Notes: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. 2.3 Test Mode Test Mode 1 Wireless charging output (Phone+ Earphone+ Watch): Full load Test Mode 2 Wireless charging output (Phone+ Earphone+ Watch): Half load Test Mode 3 Wireless charging output (Phone+ Earphone+ Watch): Empty load Note: All test mode were tested and passed, only shows the worst case mode which were recorded in this report. Report No.: BCTC2406629509-2E No.：BCTC/RF-EMC-005 Page 6 of 11 Edition：B.2 3. Test Facility And Test Instrument Used 3.1 Test Facility All measurement facilities used to collect the measurement data are located at Shenzhen BCTC Testing Co., Ltd. Address:1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China. The site and apparatus are constructed in conformance with the requirements of ANSI C63.4 and CISPR 16-1-1 other equivalent standards. FCC Test Firm Registration Number: 712850 A2LA certificate registration number is: CN1212 ISED Registered No.: 23583 ISED CAB identifier: CN0017 3.2 Test Instrumen…

Text truncated - open the document above for the full version.

Customer namePart number 43.5±0.5 39.0±0.5 20.5±0.5 5.7 18.0ref 3±1 70.0±2 0.65±0.1 argument L06.5±10%μH■TH1816B Q>60 min■TH1816B DCR<50mΩ■CH-502BC ♦、Temperature class: Operating temperature -40°C~ 125°C Serial number name 1 Magneti c sheet 2 Copper wire 3 Adhesiv e tape 4 tin 5 glue Product specification Manufacturer: Matsushima Technology Cable Company Address: 7th Floor, Building 9, Fourth Industrial Zone, Hongxing Village, Guangming District, Shenzhen Testing instrument ♦、Bill of materials: 43.5*5.3*0.65T 0.08*24P 8MM 107H glue specificationTest condition 100KHz/1V 100KHz/1V @ 25°C specification ♦、Electrical characteristic: G1.8Max H I A B C D E F HTZ20C ♦、Overall dimension (unit: mm)

Customer namePart number 21.0±0.5 15.0±0.5 7.5±0.5 12.0±1 2.0±1 2.2Max argument L06.5±10% μH■TH1816B Q>28min■TH1816B DCR<20mΩ■CH-502BC ♦、Temperature class: Operating temperature -40°C~ 125°C ♦、Bill of materials: Serial number name 1 Magnet ic 2 Copper wire 3 Adhesi ve 4 tin 5 glue Product specification Testing instrument Manufacturer: Matsushima Technology Cable Company Address: 7th Floor, Building 9, Fourth Industrial Zone, Hongxing Village, Guangming District, Shenzhen G25 0.08*24P 7.5*2.2，3100GS 107H glue specificationTest condition 100KHz/1V 100KHz/1V @ 25°C specification ♦、Electrical characteristic: G2.5Max A B C D E F 148 ♦、Overall dimension (unit: mm)

No.：BCTC/RF-EMC-005 Page 1 of 28 Edition：B.2 TEST REPORT Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2406629509-1E Applicant: Shenzhen Hudson Technology Co., Ltd. Product Name: 3-IN-1 WIRELESS CHARGING STAND Test Model: 712818 Tested Date: 2024-06-18 to 2024-06-27 Issued Date: 2024-06-28 Report No.: BCTC2406629509-1E No.：BCTC/RF-EMC-005 Page 2 of 28 Edition：B.2 FCC ID: 2BHCG-712818STAND The test report is effective only with both signature and specialized stamp. This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full. The tested sample(s) and the sample information are provided by the client. Product Name: 3-IN-1 WIRELESS CHARGING STAND Trademark: Model/Type reference: 712818 Prepared For: Shenzhen Hudson Technology Co., Ltd. Address: RM409, LvKai Building, 71 Zone, Xindong Xin'an Street, Baoan District, Shenzhen, China 518100 Manufacturer: Shenzhen Hudson Technology Co., Ltd. Address: RM409, LvKai Building, 71 Zone, Xindong Xin'an Street, Baoan District, Shenzhen, China 518100 Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China. Sample Received Date: 2024-06-18 Sample tested Date: 2024-06-18 to 2024-06-27 Issue Date: 2024-06-28 Report No.: BCTC2406629509-1E Test Standards: FCC Part15.209 ANSI C63.10-2013 Test Results: PASS Tested by: Approved by: Lei Chen/Project Handler Zero Zhou/Reviewer Report No.: BCTC2406629509-1E No.：BCTC/RF-EMC-005 Page 3 of 28 Edition：B.2 Table Of Content Test Report Declaration Page 1. Version .................................................................................................................. 4 2. Test Summary ....................................................................................................... 5 3. Measurement Uncertainty ..................................................................................... 6 4. Product Information And Test Setup ..................................................................... 7 4.1 Product Information ............................................................................................... 7 4.2 Support Equipment ............................................................................................... 7 4.3 Test Setup Configuration ...................................................................................... 8 4.4 Test Mode ............................................................................................................. 8 5. Test Facility And Test Instrument Used ................................................................. 9 5.1 Test Facility ........................................................................................................... 9 5.2 Test Instrument Used ............................................................................................ 9 6. Conducted Emissions .......................................................................................... 11 6.1 Block Diagram Of Test Setup .............................................................................. 11 6.2 Limit .................................................................................................................... 11 6.3 Test Procedure ................................................................................................... 11 6.4 EUT Operating Conditions .................................................................................. 11 6.5 Test Result .......................................................................................................... 12 7. Radiated Emissions ............................................................................................. 14 7.1 Block Diagram Of Test Setup .............................................................................. 14 7.2 Limit .................................................................................................................... 15 7.3 Test Procedure ................................................................................................... 15 7.4 Test Result .......................................................................................................... 16 8. Bandwidth Test .................................................................................................... 20 9. Antenna Requirements ........................................................................................ 24 10. EUT Photographs ................................................................................................ 25 11. EUT Test Setup Photographs.............................................................................. 26 (Note: N/A Means Not Applicable) Report No.: BCTC2406629509-1E No.：BCTC/RF-EMC-005 Page 4 of 28 Edition：B.2 1. Version Report No. Issue Date Description Approved BCTC2406629509-1E 2024-06-28 Original Valid Report No.: BCTC2406629509-1E No.：BCTC/RF-EMC-005 Page 5 of 28 Edition：B.2 2. Test Summary The Product has been tested according to the following specifications: No. Test Parameter Clause No. Results 1 Conducted Emission 15.207 PASS 2 Radiated Emission 15.209 PASS 3 20dB Bandwidth 15.215 PASS 4 Antenna Requirement 15.203 PASS Report No.: BCTC2406629509-1E No.：BCTC/RF-EMC-005 Page 6 of 28 Edition：B.2 3. Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the Product as specified in CISPR 16-4-2. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. No. Item Uncertainty 1 3m chamber Radiated spurious emission(9kHz-30MHz) U=3.7dB 2 3m chamber Radiated spurious emission(30MHz-1GHz) U=4.3dB 3 3m chamber Radiated spurious emission(1GHz-18GHz) U=4.5dB 4 3m chamber Radiated spurious emission(18GHz-40GH…

Text truncated - open the document above for the full version.

Report No.: BCTC2406629509-1E No.：BCTC/RF-EMC-005 Page 26 of 28 Edition：B.2 11. EUT Test Setup Photographs Conducted Emissions Photo Radiated Measurement Photos Report No.: BCTC2406629509-1E No.：BCTC/RF-EMC-005 Page 27 of 28 Edition：B.2 Report No.: BCTC2406629509-2E No.：BCTC/RF-EMC-005 Page 10 of 11 Edition：B.2 5. Photographs Of Test Set-Up