2BHFX-1040001Babba Baby Bottle Cooler and Warmer

User Manual Product Overview and Intended Use: The Babba baby bottle cooler and warmer enable parents to more easily feed their baby. The Base attaches to the Bottle to either cools the milk as if it was sitting in a refrigerator or warms it to body temperature prior to feeding. Status Light: Green: Standby Pulsing Blue: Cooling Solid Blue: Bottle is cold Pulsing Red: warming Solid Red: Bottle is warm Battery Light: Blinking Orange: Low Battery Solid Orange: Charging Green: Fully Charged Nipple Flow Rates: Level 1: 0-3 months Level 2: 3+ months Level 3: 6+ months Level 4: High Flow Download the App: Open or download the Babba App on your smartphone. The App allows you to control the device remotely, check the remaining battery life, schedule a time for the bottle to be warmed, and download the latest firmware. Cleaning Instructions: The Babba Base contains electronics, which should be kept dry. Just wipe the top of Babba with one of the provided Breast Pump wipes, or use a damp cloth with a dab of soap. The removable tan gasket, bottle, and bottle parts (Nipples, Collar, and Cover) may all be washed with soap and water, or washed in the top rack of the dishwasher. Operating Instructions: Step 1: Pour milk or formula into the insulated. Step 2: Attach the Base device to the top of the bottle. Next flip it over so that the Base is on the bottom and the bottle is on top. Step 3: Press the button (on control it through the app) to begin cooling and take it with you. Then press the same button to warm the bottle when it is time to feed. Turning off the device: press the button until it cycles to off (Status Light is off), or long press the button in any state to turn off the device. Charging the device: Plug the Power Adapter in the back of the unit and charge the device until the Battery Light changes from orange to green. Safety Precautions: ● The device must remain vertical in operation so that the milk/formula remains in contact with the thermal plate. ● Do not get the sides or bottom of the device wet. Only the top of the device with the thermal plate is sealed. ● Do not block or cover the side vents. ● Do not operate in environments exceeding 80°F or the cooling performance may suffer. ● Avoid direct sunlight on the device. ● Only use the Power Adapter provided with the device. ● To avoid risk of strangulation, do not leave a baby or child unattended with the Power Adapter. Troubleshooting: ● Device not turning on: press the button on the device; plug the Power Adapter in to charge. ● Milk/formula not getting cold/warm: ensure the device is vertical so that the fluid is in contact with the thermal plate; it has not been cooling/warming long enough; the outside environment is too cool/hot; the vents on the side are obstructed. ● Button press not responding: charge the device; possible misalignment - contact customer support. ● Cannot connect the Smartphone App to the device: ensure Bluetooth is enabled on your Smartphone; ensure the device is on and the app is pulled up on phone; kill the App and restart the App. ● Outdated Firmware: download the latest App and pair with Babba device to ensure the device is operating with the latest firmware. To hard reset the device, plug in the Power Adapter and press the Device’s button for 10 seconds. Please email us at [email protected] for any issues. Customer support is eager to help. Technical Specifications: Product Name: Babba Baby Bottle Cooler and Warmer Device model: 104-0001 Device dimensions: 8.5” x 3” x 3” Device weight: 2 lbs Power Adapter Input: 100-240V AC, 50/60Hz, 1.3A Power Adapter Output: 14.0V 3.0A 42.0W Battery Pack: rechargeable lithium ion battery (11.1V, 3S1P Configuration, 18650 cells, 3200mAh, 35.52Wh) Microcontroller Unit: nRF52832 Transmitter/Antenna Type: Bluetooth 5.0 Wireless Technology Frequency: 2.4GHz (Bluetooth) Modulation: GFSK at 1 Mbps, 2 Mbps data rates Designed by Babba Care, Inc. Product made in China. FCC and ISED Compliance: FCC ID: 2BHFX-1040001 IC: 32751-1040001 FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC/ISED RF Exposure statement This equipment complies with FCC and ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. In order to avoid the possibility of ex…

Text truncated - open the document above for the full version.

July 5, 2024 Nemko North America, Inc. 303 River Road Ottawa ON K1V 1H2 Canada ATTN.: Reviewing Engineer Subject: FCC Certification - Equipment Not Covered by Prohibition (FCC ID: 2BHFX- 1040001) Applicant: Babba Care Inc. This letter serves as a certification by Babba Care Inc. ("the Applicant") that the equipment under application for FCC authorization (FCC ID: 2BHFX-1040001) is not considered "covered" equipment prohibited from receiving authorization under Section §2.903 of the FCC Rules. Verification of non-coverage The Applicant has conducted a thorough review of the current FCC Covered List and confirms that, as of the application filing date, the equipment is not manufactured by any entity identified on the list. Additionally, the Applicant itself is not currently identified on the Covered List as a producer of "covered" equipment. Note: If, in the future, the equipment or the Applicant's status changes in relation to the FCC Covered List, the Applicant will promptly notify the FCC and take all necessary actions to comply with the relevant regulations. Signed: Printed name: Daniel Evans Title: CEO Company Name: Babba Care, Inc. Date: July 7, 2024

* the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. ** the agent does not have an FRN because they do no other business with the FCC except for acting as a US agent for service of process, and therefore are not required to have their own FRN. U.S. Agent Designation for Service of Process - Certification Attestation Letter July 5, 2024 Nemko North America, Inc. 303 River Road Ottawa ON K1V 1H2 Canada ATTN.: Reviewing Engineer FCC ID: 2 BHFX-1040001 Applicant FRN: 0035649474 This letter serves as a formal designation, pursuant to §2.911(d)(7) of the FCC Rules, of the following U.S. Agent* for Service of Process for the equipment under application: U.S. Agent for Service of Process: • Company Name: Babba Care Inc. • Physical U.S. Company Address: 1974 Amarillo Pl., Escondido, CA 92025 • Agent Name: Daniel Evans • Agent Email Address: [email protected] • Agent FRN**: 0035649474 The above listed designated agent hereby acknowledges and accepts the obligation for service of process on behalf of the applicant signed below. The applicant further acknowledges and accepts its obligation to maintain a U.S. Agent for Service of Process for a minimum period of one year following either: • Permanent termination of all marketing and importation activities within the U.S. for the applicable equipment by the grantee. • The conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever occurs later. Applicant Signed: Designated Agent Signed: (Required, if different to Applicant) Signed: Signed: Printed name: Daniel Evans Printed name: Click here to enter text. Title: CEO Title: Click here to enter text. Company Name: Babba Care Inc. Company Name: Click here to enter text. Date: July 5, 2024 Date: Click here to enter a date.

Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Appointment of Agent for FCC and ISED Certification Application Dear Director of Certification, This letter formally appoints Spencer Zhong of Nemko Canada, Inc. located at 303 River Road, Ottawa, Ontario, Canada K1V 1H2, as our authorized agent to represent us in the application process for equipment certification. We confirm that the submitted documents accurately depict the device or system seeking certification. Additionally, we guarantee that all units produced, imported, or marketed, as defined by FCC and ISED Canada regulations, will possess a label identical to the one submitted with this application. By signing below, we certify that neither our company nor any party involved in the application is subject to denial of federal benefits, including FCC benefits, as outlined in Section 5301 of the Anti- Drug Abuse Act of 1988 (21 U.S.C. §862) due to a conviction for possession or distribution of a controlled substance. Furthermore, no party involved in the application, as defined in 47 CFR 1.2002 (b), is subject to denial of federal benefits, including FCC benefits. We attest to the truth and accuracy of the information provided to the FCC to the best of our knowledge (47 CFR 2.911 (d)) and acknowledge our responsibilities as a grantee regarding certified equipment (47 CFR 2.909). In instances where our authorized agent signs the application for certification on our behalf, we understand that Nemko North America, Inc. remains solely responsible for adhering to the terms and conditions for certification as specified by Nemko Canada Inc. Sincerely, Dated: June 13, 2024 Agency agreement expiration date: December 31, 2024 *Up to 12 months Signed by: Signature Print name Title Phone On behalf of: Company name Daniel Evans CEO +1 978-6121-3437 Babba Care, Inc.

July 3, 2024 Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Request for Confidentiality – FCC FCC ID: 2BHFX-1040001 Pursuant to FCC 47 CFR 0.457(d)(1)(ii) and 0.459 and FCC guidance published in KDB 726920, we hereby request confidential treatment of information accompanying this application as outlined below. We request the exhibits selected below as long term confidential (LTC) be withheld from public view permanently: Selection of exhibits for LTC - general Exhibit name ☒ Permanent (Long Term) Block Diagrams ☒ Permanent (Long Term) Operation Description / Theory of Operation ☒ Permanent (Long Term) Parts List & Placement / BOM ☒ Permanent (Long Term) Schematics Selection of exhibits for LTC - specific 1 Exhibit name ☐ Permanent (Long Term) Tune-Up Procedure ☐ Permanent (Long Term) SDR 2 Software / Security Info Selection of exhibits for LTC (with NDA) 3 Exhibit name ☐ Permanent (Long Term) User’s Manual ☐ Permanent (Long Term) Internal Photos We also request the exhibits selected below as short term confidential (STC) be withheld from public view for a period of 0 days 4 from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public: Selection of exhibits for STC 5 Exhibit name ☐ Short Term Block Diagrams ☐ Short Term Operation Description / Theory of Operation ☐ Short Term Parts List & Placement / BOM ☐ Short Term Schematics ☐ Short Term User’s Manual ☐ Short Term Internal Photos ☐ Short Term External Photos ☐ Short Term Test Setup Photos ☐ Short Term Tune-Up Procedure (for Licensed equipment only) Our company has spent a substantial effort in developing this product and it is one of the first of its kind in the industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. When the device is marketed before the requested number of days listed above, the grantee will inform the TCB to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. 1 - Tune up procedure is applicable only for licensed equipment. 2 - The FCC rules require that any radio, in which the software is designed or expected to be modified by a party other than the manufacturer that would affect the operating parameters of frequency range, modulation type, maximum output power or other radio frequency parameters outside the range under which the transmitter has been approved in accordance with the FCC rules, must be certified as a software-defined radio (SDR). 3 - These items require further information to be provided to TCB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and review section II, 3) regarding specific information (NDA) that must accompany these requests. 4 - Number of days can be listed up to 180 but should not go past the date of beginning of product marketing/sale. 5 - Any exhibits that may have already been requested to have “Permanent” confidentiality need not be repeated under Short-Term confidentiality request. The above information contains trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Sincerely, Signed by: Signature Print name Title Phone Company Address Daniel Evans CEO 978-621-3437 Babba Care, Inc. 1974 Amarillo Pl., Escondido, CA 92025

Label design Label location

www.nemko.com Nemko USA Inc., a testing laboratory, is accredited by ANAB. The tests included in this report are within the scope of this accreditation. Choose Scandinavian trust Assessment Report REP047893-3R1ARFWL Type of assessment: MPE Calculation report Manufacturer: Model: Babba Care, Inc. 104-0001 Product Name: Model variant(s): Babba Baby Bottle Cooler and Warmer N/A FCC ID: IC certification number: 2BHFX-1040001 32751-1040001 Specification:  FCC 47 CFR Part 1 Subpart I, §§1.1307, 1.1310  FCC 47 CFR Part 2 Subpart J, §2.1091  FCC KDB 447498 D01 General RF Exposure Guidance v06  ISED Canada RSS-102 Issue 5 Amendment 1, (February 2021) RSS-102 Annex B - Declaration of RF Exposure Compliance ATTESTATION: I attest that the information provided in Annex A is correct; that the Technical Brief was prepared and the information contained therein is correct; that the device evaluation was performed or supervised by me; that applicable measurement methods and evaluation methodologies have been followed; and that the device meets the SAR and/or RF field strength limits of RSS-102. Date of issue: July 24, 2024 James Cunningham, EMC/WL Manager Prepared by Signature Report reference ID: REP047893-3R1APFWL Page 2 of 5 Lab locations= Company name Nemko USA Inc. Address 2210 Faraday Ave, Suite 150 City Carlsbad State California Postal code 92008 Country USA Telephone +1 760 444 3500 Website www.nemko.com FCC Site Number Test Firm Registration Number: 392943 Designation Number: US5058 ISED Test Site 2040B-3 Prepared by James Cunningham, EMC/WL Manager Date July 24, 2024 Signature Limits of responsibility Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. All results contain in this report are within Nemko USA’s ISO/IEC 17025 accreditation. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. Copyright notification Nemko USA Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko USA Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. © Nemko USA Inc. Report reference ID: REP047893-3R1APFWL Page 3 of 5 Table of Contents Table of Contents ......................................................................................................................................................................................................... 3 Evaluation summary ........................................................................................................................................................................... 4 1.1 MPE calculation for standalone transmission ........................................................................................................................................................... 4 Report reference ID: REP047893-3R1APFWL Page 4 of 5 Evaluation summary 1.1 MPE calculation for standalone transmission 1.1.1 References, definitions, and limits FCC §2.1091(d) (2) (2) For operations within the frequency range of 300 kHz and 6 GHz (inclusive), the limits for maximum permissible exposure (MPE), derived from whole-body SAR limits and listed in Table 1 in paragraph (e)(1) of this section, may be used instead of whole-body SAR limits as set forth in paragraphs (a) through (c) of this section to evaluate the environmental impact of human exposure to RF radiation as specified in §1.1307(b) of this part, except for portable devices as defined in §2.1093 of this chapter as these evaluations shall be performed according to the SAR provisions in §2.1093. Table 1.1-1: Table 1 to §1.1310(e)(1)—Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (i) Limits for Occupational/Controlled Exposure 0.3–3.0 614 1.63 *(100) ≤6 3.0–30 1842 / f 4.89 / f *(900 / f 2 ) <6 30–300 61.4 0.163 1.0 <6 300–1500 f / 300 <6 1500–100000 5 <6 (ii) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) <30 1.34–30 824 / f 2.19 / f *(180 / f 2 ) <30 30–300 27.5 0.073 0.2 <30 300–1500 f / 1500 <30 1500–100000 1.0 <30 Notes: f = frequency in MHz. * = Plane-wave equivalent power density. RSS-102, Section 2.5.2 RF exposure evaluation is required if the separation distance between the user and/or bystander and the device’s radiating element is greater than 20 cm, except when the device operates as follows: • below 20 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1 W (adjusted for tune- up tolerance); • at or above 20 MHz and below 48 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 4.49/ƒ 0.5 W (adjusted for tune-up tolerance), where ƒ is in MHz; • at or above 48 MHz and below 300 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 0.6 W (adjusted for tune-up tolerance); • at or above 300 MHz and below 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 0.0131 ƒ 0.6834 W (adjusted for tune-up tolerance), where ƒ is in MHz; • at or above 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 5 W (adjusted for tune-up tolerance). In these cases, the information contained in the RF exposure technical brief may be limited to information that demonstrates how the e.i.r.p. w…

Text truncated - open the document above for the full version.

www.nemko.com FCC Antenna Gain.dotm, Version V1.0 REP041407-1TRFEMC Date of issue: May 24, 2024 Applicant: Babba Care, Inc. Product: Electronic baby bottle cooler and warmer Model: Variant(s): 104-0001 None Specifications:  2D Antenna Pattern and Peak Gain Test report Report reference ID: REP041407-1TRFEMC Page 2 of 16 Lab and test locations Company name Nemko USA Inc. Address 2210 Faraday Ave, Suite 150 City Carlsbad State California Postal code 92008 Country USA Telephone +1 760 444 3500 Website www.nemko.com FCC Site Number Test Firm Registration Number: 392943; Designation Number: US5058 ISED Test Site 2040B-3 Tested by Chenhao Ma, Wireless Test Technician Reviewed by James Cunningham, EMC/WL Manager Review date May 24, 2024 Reviewer signature Limits of responsibility Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. Copyright notification Nemko USA Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko USA Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. © Nemko USA Inc. Report reference ID: REP041407-1TRFEMC Page 3 of 16 Table of Contents Table of Contents ......................................................................................................................................................................................................... 3 Report summary ................................................................................................................................................................................. 4 1.1 Test specifications .................................................................................................................................................................................................... 4 1.2 Exclusions ................................................................................................................................................................................................................. 4 1.3 Statement of compliance .......................................................................................................................................................................................... 4 1.4 Test report revision history ....................................................................................................................................................................................... 4 Summary of test results ...................................................................................................................................................................... 5 2.1 Sample information .................................................................................................................................................................................................. 5 2.2 Testing period ........................................................................................................................................................................................................... 5 2.3 Test results ............................................................................................................................................................................................................... 5 Equipment (antenna) under test (EUT) details ..................................................................................................................................... 6 3.1 Disclaimer ................................................................................................................................................................................................................. 6 3.2 Applicant................................................................................................................................................................................................................... 6 3.3 Manufacturer............................................................................................................................................................................................................ 6 3.4 EUT information ....................................................................................................................................................................................................... 6 3.5 Antenna information ................................................................................................................................................................................................ 6 3.6 EUT setup details ...................................................................................................................................................................................................... 7 Engineering considerations ................................................................................................................................................................. 8 4.1 Modifications incorporated in the EUT ..................................................................................................................................................................... 8 4.2 Technical judgement ................................................................................................................................................................................................ 8 4.3 Deviations from laboratory test procedures .......…

Text truncated - open the document above for the full version.

www.nemko.com FCC 15.247 & RSS-247 (BLE).dotm, Version V1.1 Nemko USA Inc., a testing laboratory, is accredited by ANAB. The tests included in this report are within the scope of this accreditation. REP047893-1R2TRFWL Date of issue: August 13, 2024 Applicant: Babba Care, Inc. Product description: Babba Baby Bottle Cooler and Warmer Model: Product marketing name(s): 104-0001 N/A FCC ID: ISED certification number: 2BHFX-1040001 32751-1040001 Specifications:  FCC 47 CFR Part 15, Subpart C – §15.247 Operation within the bands 902 – 928 MHz, 2400 – 2483.5 MHz, 5727 – 5850 MHz  Industry Canada RSS-247, Issue 3 Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and Licence-Exempt Local Area Network (LE-LAN) Devices Test report Report reference ID: REP047893-1R2TRFWL Page 2 of 48 Lab and test locations Company name Nemko USA Inc. Address 2210 Faraday Ave, Suite 150 City Carlsbad State California Postal code 92008 Country USA Telephone +1 760 444 3500 Website www.nemko.com FCC Site Number Test Firm Registration Number: 392943; Designation Number: US5058 ISED Test Site 2040B-3 Tested by Chenhao Ma, Wireless Test Technician Reviewed by James Cunningham, EMC/WL Manager Review date August 13, 2024 Reviewer signature Limits of responsibility Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. All results contain in this report are within Nemko USA’s ISO/IEC 17025 accreditation. This report must not be used by the client to claim product certification, approval, or endorsement by ANAB, NIST, or any agency of the U.S. Government. Copyright notification Nemko USA Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko USA Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. © Nemko USA Inc. Report reference ID: REP047893-1R2TRFWL Page 3 of 48 Table of Contents Table of Contents ......................................................................................................................................................................................................... 3 Report summary ................................................................................................................................................................................. 4 1.1 Test specifications ..................................................................................................................................................................…

Text truncated - open the document above for the full version.