2BHQP-M161A-016Lithium Jump Starter

WARRANTY The manufacturer warrants this product for 12 months against defective material or workmanship under normal use. This limited warranty is void if the product is misused, subjected to careless handling, repaired, or modified by anyone other than manufacturer. -12- FCC Warning Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐‐ Reorient or relocate the receiving antenna. ‐‐ Increase the separation between the equipment and receiver. ‐‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐‐ Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.

U.S. Agent Designation for Service of Process (Applicant and U.S. Agent are Separate Parties) TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: HOPEK CORPORATION INC Address:4358 S BANNOCK ST ENGLEWOOD, CO 80110 United States FRN:0034562900 Contact Name: Peter Davis Tel.: 561-235-6113 Email: [email protected] This letter is to confirm that we (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Date: August 19, 2024 Signed by (Printed Name): Peter Davis The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company Name: Shenzhen Macson Power Co.,Ltd. Address: 201 Xiangqian Building, No.4012 Longgang Avenue, Longgang District, Shenzhen City, China Contact Name: Mao xiaojun FRN: 0035704089 Telephone No: 13302965785 Email: [email protected] FCC ID: 2BHQP-M161A-016 Applicant Signature: Date: August 19, 2024 Signed by (Printed Name): Mao xiaojun

(Shenzhen Macson Power Co.,Ltd.) (2024.8.12) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for (FCC ID: 2BHQP-M161A-016) [Shenzhen Macson Power Co.,Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Client’s signature: Client’s name : Mao xiaojun (Shenzhen Macson Power Co.,Ltd.) (2024.8.12) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for (FCC ID: 2BHQP-M161A-016) [Shenzhen Macson Power Co.,Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Client’s signature: Client’s name : Mao xiaojun

Shenzhen Macson Power Co.,Ltd. 2024.8.12 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen BCTC Testing Co., Ltd to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Client’s signature: Client’s name / title : Mao xiaojun/ Manager Contact information / address: 201 Xiangqian Building, No.4012 Longgang Avenue, Longgang District, Shenzhen City, China

Shenzhen Macson Power Co.,Ltd. 2024.8.12 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: CONFIDENTIALITY REQUEST FOR EUT NAME: Lithium Jump Starter Trademark: N/A MODEL: M161A-016 M161A-080, M161A-010, M161A-012, JS161A-000, JS161A-080, JS161A-100, JS161A-120 FCC ID: 2BHQP-M161A-016 To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the - Block Diagram - Schematics - Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Client’s signature: Client’s name / title : Mao xiaojun/ Manager Contact information / address: 201 Xiangqian Building, No.4012 Longgang Avenue, Longgang District, Shenzhen City, China

Shenzhen Macson Power Co.,Ltd. Model Difference 2024/8/12 EUT NAME: Lithium Jump Starter Trademark: N/A MODEL: M161A-016 M161A-080, M161A-010, M161A-012, JS161A-000, JS161A-080, JS161A-100, JS161A-120 FCC ID: 2BHQP-M161A-016 All the models are the same circuit and RF module, except their model names and appearance color. Regards Sincerely Client’s signature: Client’s name / title : Mao xiaojun/ Manager Contact information / address: 201 Xiangqian Building, No.4012 Longgang Avenue, Longgang District, Shenzhen City, China

External Photos

Label & label location Location: Label: FCC ID: 2BHQP-M161A-016 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.

Internal Photos Antenna

No.：BCTC/RF-EMC-005 Page 1 of 15 Edition：B.2 TEST REPORT Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2407365171-2E Applicant: Shenzhen Macson Power Co.,Ltd. Product Name: Lithium Jump Starter Test Model: M161A-016 Tested Date: 2024-07-16 to 2024-07-26 Issued Date: 2024-07-26 Report No.: BCTC2407365171-2E No.：BCTC/RF-EMC-005 Page 2 of 15 Edition：B.2 FCC ID: 2BHQP-M161A-016 The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: Lithium Jump Starter Trademark: N/A Model/Type Reference: M161A-016 M161A-080, M161A-010, M161A-012, JS161A-000, JS161A-080, JS161A-100, JS161A-120 Prepared For: Shenzhen Macson Power Co.,Ltd. Address: 201 Xiangqian Building, No.4012 Longgang Avenue, Longgang District, Shenzhen City, China Manufacturer: Shenzhen Macson Power Co.,Ltd. Address: 201 Xiangqian Building, No.4012 Longgang Avenue, Longgang District, Shenzhen City, China Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China. Sample Received Date: 2024-07-16 Sample Tested Date: 2024-07-16 to 2024-07-26 Issue Date: 2024-07-26 Report No.: BCTC2407365171-2E Test Standards: FCC CFR 47 part1, 1.1307(b), 1.1310 Test Results: PASS Tested by: Approved by: Shanshan. Zhang / Project Handler Zero Zhou/Reviewer Report No.: BCTC2407365171-2E No.：BCTC/RF-EMC-005 Page 3 of 15 Edition：B.2 Table Of Content Test Report Declaration Page 1. Version .................................................................................................................. 4 2. Product Information ............................................................................................... 5 2.1 Product Information ............................................................................................... 5 2.2 Support Equipment ............................................................................................... 5 2.3 Test Mode ............................................................................................................. 6 3. Test Facility And Test Instrument Used ................................................................. 7 3.1 Test Facility ........................................................................................................... 7 3.2 Test Instrument Used ............................................................................................ 7 4. Method Of Measurement ....................................................................................... 8 4.1 Applicable Standard .............................................................................................. 8 4.2 Block Diagram Of Test Setup ................................................................................ 8 4.3 Limit ...................................................................................................................... 9 4.4 Test procedure ...................................................................................................... 9 4.5 Equipment Approval Considerations ................................................................... 10 4.6 E and H field Strength ......................................................................................... 11 5. Photographs Of Test Set-Up ............................................................................... 14 (Note: N/A Means Not Applicable) Report No.: BCTC2407365171-2E No.：BCTC/RF-EMC-005 Page 4 of 15 Edition：B.2 1. Version Report No. Issue Date Description Approved BCTC2407365171-2E 2024-07-26 Original Valid Report No.: BCTC2407365171-2E No.：BCTC/RF-EMC-005 Page 5 of 15 Edition：B.2 2. Product Information 2.1 Product Information Model/Type Reference: M161A-016 M161A-080, M161A-010, M161A-012, JS161A-000, JS161A-080, JS161A-100, JS161A-120 Model Differences: All the model are the same circuit and RF module, except model names and appearance of the color. Hardware Version: N/A Software Version: N/A Modulation: ASK Operation Frequency: 115kHz-205kHz Antenna installation: loop coil antenna Ratings: Input: PD 60W Max Type-C output: DC 20V/3A Max USB-A Output #1: DC 5V/3A, DC 9V/2A, DC 12V/1.5A USB-A Output #2: DC 5V/2.4A Wireless charging: 10W Max Battery: DC 14.8V 2.2 Support Equipment No. Device Type Brand Model Series No. Note E-1 Lithium Jump Starter N/A M161A-016 Ref. the Section 4.1 EUT E-2 ADAPTER Hoco. N18 N/A Auxiliary E-3 Load N/A N/A N/A Auxiliary Notes: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. Report No.: BCTC2407365171-2E No.：BCTC/RF-EMC-005 Page 6 of 15 Edition：B.2 2.3 Test Mode DC Mode Mode 1 Full Load Mode 2 Half Load Mode 3 Null Load Note: All test mode were tested and passed, only shows the worst case mode which were recorded in this report. Report No.: BCTC2407365171-2E No.：BCTC/RF-EMC-005 Page 7 of 15 Edition：B.2 3. Test Facility And Test Instrument Used 3.1 Test Facility All measurement facilities used to collect the measurement data are located at Shenzhen BCTC Testing Co., Ltd. Address:1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China. The site and apparatus are constructed in conformance with the requirements of ANSI C63.4 and CISPR 16-1-1 other equivalent standards. FCC Test Firm Registration Number: 712850 A2LA certificate registration number is: CN1212 ISED Registered No.: 23583 ISED CAB identifier: CN0017 3.2 Test Instrument Used EMF Test Equipment Manufacturer Model# Serial# Las…

Text truncated - open the document above for the full version.

深 圳 市 深 广 电 子 有 限 公 司 Shenzhen Shenguang Electronic Technology Co.,LTD 客 戶： CUSTOMER: 客 戶 料 號： CUST P/N: 名 称： NAMA P/N: 産 品 型 號： DESC: 日 期： DATE: 版 本： Version: 深圳市合涟聚电子科技有限责任公司 A11单孔双槽背胶线长60MM 线圈面+磁片面贴1.0MM 厚双面EVA背胶 2024.08.13 A.0 擬制 PREPARED BY 審核 CHECKED BY 批准 APPROVED BY 客戶承認 CUSTOMER APPROVE 谢燕琪 段家旺 谢小仔 深 圳 市 深 广 电 子 有 限 公 司 Shenzhen Shenguang Electronic Technology Co.,LTD Version Change History 版本 Rev. 變 更 前 Before Chang 變 更 後 After Change 更 改 日 期 Change Date 批 准 Approved By A.0 新发行 ---- 20240813 谢小仔 深 圳 市 深 广 电 子 有 限 公 司 Shenzhen Shenguang Electronic Technology Co.,LTD 産 品 型 號： DESC A11单孔双槽背胶线长60MM 线圈面+磁片面贴1.0MM厚双面 EVA背胶 版本 Rev：A.0 客戶 CUST: 客户料号 CUST P/N: 一、尺寸 DIMENSION:(mm) 二、原理图 SCHEMATIC DIAGRAM: A 50±1 B 42±1.5 H 60±2 E 2-5 I 1.0±0.1 G 1.0±0.05 T 5.0Max 注： 1.交叉出线; 2.磁片尺寸 50±1mm,厚度为 1.0±0.1mm。 3、线圈面与磁片面贴1.0EVA海绵 4、折线位置贴 8mm 高温胶纸 三、绕线参数 Winding Specification: 序号 NO. 端子 TERMINAL 线径 WIRE 圈数 Turns 绕线方向 Winding Direction 1 S F 丝包线 0.08*105P 10Ts CCW 四、 电气特性 ELECTRICAL CHARACTERISTICS: 温度 TEMPERATURE:25±10°C, 湿度 RELATIVE HUMIDITY:65±20% 序号 NO. 项目 ITEM 端子 TERMINAL 标准 SPECIFICATION 测试条件 TEST FREQUENCY 测试仪器 TEST EQUIPMENTS 1 IND. S-F 3.8uH ±10%单独线圈 100KHz/1.0V CH 1063 2 IND. S-F 6.5uH ±10%加磁片 100KHz/1.0V CH 1063 3 DCR S-F 45mΩ MAX 100KHz/1.0V 502BC 4 Q S-F 70MIN 100KHz/1.0V 502BC 擬制/日期 PREPARED BY/DATE 審核/日期 CHECKED BY/DATE 2024-8-13 2024-8-13 深 圳 市 深 广 电 子 有 限 公 司 Shenzhen Shenguang Electronic Technology Co.,LTD 五、包装/PACKAGE 5.1 5.2包装数量及规格 Packing Quantity: 5.3包装以现有包装盘为参照标准，以实际出货包装为准，如有特需要求可以定制。 The packaging shall be based on the exusting packing plate and the actual delivery package shall prevail .If there is any requirement,we can customize it. 项目 Item 数量 Quantity 材料规格 Material 盒 Box 200 Pcs 370*265*55mm 箱 Big Carton 600 Pcs 420*270*310mm 六、贮存和使用条件 Storage and Use condition 6.1 贮存条件 Storage condition 6.1.1 建议贮存条件：温度-25°C~ 85°C ，湿度70% (Max.) Recommended keeping conditions: -25°C ~85°C, 70%RH (Max.) 6.1.2 贮存期限：自生产之日起六个月内 Storage life : Within the limits of six months from being produced. 6.2 使用条件 Use condition 使用条件限制：温度=-25°C~ 85°C, 湿度≤ 90% Use condition limit: T=-25°C~85°C, RH≤ 90%.

No.：BCTC/RF-EMC-005 Page 1 of 28 Edition：B.2 TEST REPORT Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC2407365171-1E Applicant: Shenzhen Macson Power Co.,Ltd. Product Name: Lithium Jump Starter Test Model: M161A-016 Tested Date: 2024-07-16 to 2024-07-26 Issued Date: 2024-07-26 Report No.: BCTC2407365171-1E No.：BCTC/RF-EMC-005 Page 2 of 28 Edition：B.2 FCC ID: 2BHQP-M161A-016 The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Testing Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: Lithium Jump Starter Trademark: N/A Model/Type Reference: M161A-016 M161A-080, M161A-010, M161A-012, JS161A-000, JS161A-080, JS161A-100, JS161A-120 Prepared For: Shenzhen Macson Power Co.,Ltd. Address: 201 Xiangqian Building, No.4012 Longgang Avenue, Longgang District, Shenzhen City, China Manufacturer: Shenzhen Macson Power Co.,Ltd. Address: 201 Xiangqian Building, No.4012 Longgang Avenue, Longgang District, Shenzhen City, China Prepared By: Shenzhen BCTC Testing Co., Ltd. Address: 1-2/F., Building B, Pengzhou Industrial Park, No.158, Fuyuan 1st Road, Zhancheng, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, China. Sample Received Date: 2024-07-16 Sample Tested Date: 2024-07-16 to 2024-07-26 Issue Date: 2024-07-26 Report No.: BCTC2407365171-1E Test Standards: FCC Part15.209 ANSI C63.10-2013 Test Results: PASS Tested by: Approved by: Shanshan. Zhang / Project Handler Zero Zhou/Reviewer Report No.: BCTC2407365171-1E No.：BCTC/RF-EMC-005 Page 3 of 28 Edition：B.2 Table Of Content Test Report Declaration Page 1. Version .................................................................................................................. 4 2. Test Summary ....................................................................................................... 5 3. Measurement Uncertainty ..................................................................................... 6 4. Product Information And Test Setup ..................................................................... 7 4.1 Product Information ............................................................................................... 7 4.2 Support Equipment ............................................................................................... 7 4.3 Test Setup Configuration ...................................................................................... 8 4.4 Test Mode ............................................................................................................. 9 5. Test Facility And Test Instrument Used ............................................................... 10 5.1 Test Facility ......................................................................................................... 10 5.2 Test Instrument Used .......................................................................................... 10 6. Conducted Emissions .......................................................................................... 12 6.1 Block Diagram Of Test Setup .............................................................................. 12 6.2 Limit .................................................................................................................... 12 6.3 Test procedure .................................................................................................... 12 6.4 EUT operating Conditions ................................................................................... 12 6.5 Test Result .......................................................................................................... 13 7. Radiated Emissions ............................................................................................. 15 7.1 Block Diagram Of Test Setup .............................................................................. 15 7.2 Limit .................................................................................................................... 16 7.3 Test procedure .................................................................................................... 16 7.4 Test Result .......................................................................................................... 17 8. Bandwidth Test .................................................................................................... 22 8.1 Test Procedure ................................................................................................... 22 8.2 Test Setup ........................................................................................................... 22 8.3 Test Result .......................................................................................................... 23 9. Antenna Requirements ........................................................................................ 24 9.1 Limit .................................................................................................................... 24 9.2 Test Result .......................................................................................................... 24 10. EUT Photographs ................................................................................................ 25 11. EUT Test Setup Photographs.............................................................................. 26 (Note: N/A Means Not Applicable) Report No.: BCTC2407365171-1E No.：BCTC/RF-EMC-005 Page 4 of 28 Edition：B.2 1. Version Report No. Issue Date Description Approved BCTC2407365171-1E 2024-07-26 Original Valid Report No.: BCTC2407365171-1E No.：BCTC/RF-EMC-005 Page 5 of 28 Edition：B.2 2. Test Summary The Product has been tested according to the following specifications: No. Test Parameter Clause No. Results 1 Conducted Emission 15.207 PASS 2 Radiated Emission 15.209 PASS 3 20dB Bandwidth 15.2…

Text truncated - open the document above for the full version.

Conducted emissions Radiated Measurement Photos 9kHz-30MHz 30MHz-1GHz