2BKCP-YB-W4LSmart Pet Feeder (with camera)

visual Please read this manual carefully before using the product and keep it for future reference. 01 Product List Please confirm the accessories before installation and use. (Batteries and screwdrivers are not included and need to be purchased separately) Note: To provide better products, we will periodically make improvements. The product images may slightly differ from the actual product. Please refer to the actual product. Food Tank Food Bowl User Manual Food Bowl Holder Desiccant Pack Main Unit Adapter 02 Product Overview Type-C Port Backup Battery Compartment Desiccant Box Food Bowl Food Bowl Holder Indication Lights Panel Buttons Top Cover Food Tank TF Card Slot Main Unit Microphone Adjustable Camera Press here Whether to install the batteries or not depends on individual needs. (Please purchase batteries separately. Only alkaline batteries can be used.)Note: Replace the batteries promptly when the power is low. Check and replace the batteries during holidays. 3.4 Connect the Power Take out the power adapter and insert one end into the Type-C port at the bottom of the main unit. Desiccant Bottom View of Main Unit Desiccant Box 03 Pr oduct Installation 3.1 Assemble the Main Unit ① Take out the food bowl, food bowl holder, and adapter inside the food tank before installation. ② Place the food bowl holder on a flat table or floor and then place the food bowl inside it. ③ Pick up the main unit, align it with the food bowl holder, and place it vertically down. ④ Pick up the food tank, align it with the main unit, and place it vertically down. 3.2 Install the Desiccant ① Hold the machine and lift the top cover upwards to remove it. ② Open the desiccant box, take out the desiccant packet, spread it evenly inside, and then close the desiccant box. ① Remove the power cover, insert three size C batteries into the battery compartment. ② Pay attention to the polarity during installation and finally close the power cover. 3.3 Install the Backup Battery 04 Product Use 4.1 Adding Pet Food ① Open the top cover and add the appropriate amount of pet food. 4.2 Indicator Lights and Buttons Instructions Indicator Lights Description: Buttons Description: ② Then close the top cover. When recording, the red light will turn on. W hen the power is turned on, the red light will flash briefly. The blue light will be on during playback and food dispensing. It will flash quickly if the grain is stuck. Connecting the power will turn on a green light. When the battery is low, the yellow light will flash. When connecting to the network, the green light will flash rapidly. Once the connection is successful, the green light will remain on. REC FOD RST Long press to start recording, release to end recording. Supports 15 seconds of recording, double press to delete the recording. Short press for manual feeding, long press for initialization settings. Long press for 3-5 seconds, the device will reset. REC RST FOD When turning on the power, the red light flashes, then the green light stays on. After 20 seconds, an alarm sounds. In 10 seconds, there will be a notification waiting for WiFi connection, then a power indicator light starts flashing slowly. Recording Indicator Light Food Dispensing/Food Blockage Indicator Light Working Indicator Light Record Button Manual Grain Dispensing Button Reset Key 06 Cleaning and Maintenance ① Open the top cover and take out the desiccant pack, then remove the food bowl and food bowl holder. ② Remove the food tank, separating it from the main unit. ③ Add the appropriate amount of detergent to clean the food tank, main unit, top cover, food bowl, and food bowl holder and rinse. ④ Dry and reassemble them. When cleaning the food tank interior and rotor, do not use sponges or soft cloths, and avoid using hard cleaning tools to prevent scratching on the plastic parts, which can affect the normal operation of the sensors. The main unit should not be exposed to water or soaked, but can be wiped with a damp paper towel. By pressing on the side active area to install or remove the desiccant box Rotate the grain bucket to the unlocked position, which is convenient to download the grain bucket. Product Specifications Smart Pet Feeder (with Camera) Applicable RangeCats and small dogs Video Resolution1920*1080 Food Storage Capacity4L Product WeightBased on actual product weight Product MaterialABS + Stainless Steel Suitable FoodRecommended to use 5-16mm dry non-sticky pet food Power Supply Parameters5V external power + 3x size C batteries Connection MethodWi-Fi via Bluetooth/ QR Code/ Hotspot Rated Power10W Product Size190x190x312 mm Input5V--2A Product Name User Manual Smart Pet Feeder Safety Instructions *Failure to comply with the following terms may result in improper operation or other unexpected issues. Please strictly follow the manual for installation and use of the device. Do not forcibly disassemble the device. Do not scratch or abrade the camera with sharp objects. Use indoors only. Do not place it where it can be exposed to direct sunlight, as it may affect the device's functions. Keep it away from fire sources. The device is powered by low voltage, but if a pet bites on the power cord it can still potentially cause electric leaks. Please use it correctly according to the user manual. Use the original power adapter to avoid device damage and safety hazards. Keep the device flat. Do not overturn it as it may malfunction. Do not feed anything other than pet food through the feeder, as it may cause the device to malfunction and even safety issues for your pet. Do not immerse the device in water or use in wet. To prevent pets from tipping over with the product, please place the feeder out of their reach. Do not place this device at a high location to prevent it falling as it may cause damage or pose a safety risk to pets. Dry and put the food tank back after cleaning to use it again. Do not use the device if there is water on the power cord or plug. Unplug the power cord before installin…

Text truncated - open the document above for the full version.

Shenzhen Yuben Technology CO, LTD Covered Equipment Certification Attestation Letter 12/16/2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2BKCP-YB-W4L Shenzhen Yuben Technology CO, LTD (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Shenzhen Yuben Technology CO, LTD (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Shenzhen Yuben Technology CO, LTD (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Signed: Printed name: Jiangyong Huang Title:/Click here to enter text. Company Name: Shenzhen Yuben Technology CO, LTD Date: 12/16/2025

Shenzhen Yuben Technology CO, LTD U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: December 16, 2025 Ref: Attestation Statement – Part 2.911(d)(7) filing FCC ID: 2BKCP-YB-W4L Shenzhen Yuben Technology CO, LTD(“the applicant”) certifies that, as of the date of the filing of the application, CLF Import and Export Limited (“the agent”) is our designated U.S. agent for service of process for the above reference FCC ID. The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges it is our responsibility to inform the FCC whenever the agent information changes. CLF Import and Export Limited ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name: CLF Import and Export Limited FRN: 0033489683 Address: 1312 17th Street #692, Denver, CO 80202, United States Signature: Contact Person: David Chen Tel: +1 949 254 2565 Email: [email protected] Applicant Shenzhen Yuben Technology CO, LTD FRN: 0035819911 Address: E1, Floor 7, Building 13, Lehui Science and Technology Innovation Center, 489 Jihua Road, Bantian Street, Longgang District, Shenzhen, China Signature: Contact Person: Jiangyong Huang Tel: 13008830908 Email: [email protected]

DATE: December 16, 2025 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BKCP-YB-W4L Product Name: Smart Pet Feeder (with camera) Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...) • Schematics • Block diagram • Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name: Jiangyong Huang Title: / Company: Shenzhen Yuben Technology CO, LTD

Date: December 16, 2025 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, <Signature> Name: Jiangyong Huang Title: / Company: Shenzhen Yuben Technology CO, LTD

DATE: December 16, 2025 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen CCUT Quality Technology Co., Ltd. (1F, Building 35, Changxing Technology Indstrl Park Changzhen Community, Yutang Street,Shenzhen,China) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Shenzhen Yuben Technology CO, LTD (E1, Floor 7, Building 13, Lehui Science and Technology Innovation Center, 489 Jihua Road, Bantian Street, Longgang District, Shenzhen, China). <Signature> Name: Jiangyong Huang Title: / Applicant Company: Shenzhen Yuben Technology CO, LTD

Shenzhen Yuben Technology CO, LTD Model Difference Statement Dear Sir/Madam, Added models YB-W4L01, WB-2512, YB-W10031-3, YB-W1004-1, YB-W300W4-2, YB-V300W2-3 basis of the original product YB-W4L The color of appearance and model name of series models listed are different from the main model, but the circuit and the electronic construction are the same, declared by the manufacturer. Sincerely, Name: Jiangyong Huang Company name: Shenzhen Yuben Technology CO, LTD Address: E1, Floor 7, Building 13, Lehui Science and Technology Innovation Center, 489 Jihua Road, Bantian Street, Longgang District, Shenzhen, China

Report No: SSP25100082-1&2&3E FCC ID: 2BKCP-YB-W4L Annex of Test Report Annex A. EUT External Photos Model: YB-W4L EUT View 1 EUT View 2 Report No: SSP25100082-1&2&3E FCC ID: 2BKCP-YB-W4L Annex of Test Report EUT View 3 EUT View 4 Report No: SSP25100082-1&2&3E FCC ID: 2BKCP-YB-W4L Annex of Test Report EUT View 5 EUT View 6 Report No: SSP25100082-1&2&3E FCC ID: 2BKCP-YB-W4L Annex of Test Report EUT View 7 EUT View 8 Report No: SSP25100082-1&2&3E FCC ID: 2BKCP-YB-W4L Annex of Test Report EUT View 9

Report No: SSP25100082-1&2&3E FCC ID: 2BKCP-YB-W4L Annex of Test Report Annex D. Label and Information FCC Label Sample FCC Label Specifications Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Where the EUT is constructed in two or more sections connected by wires and marketed together, the above statement is required to be affixed only to the main control unit. When the EUT is so small or for such use that it is not practicable to place the statement on it, the above information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. FCC Label Location

Report No: SSP25100082-1&2&3E FCC ID: 2BKCP-YB-W4L Annex of Test Report Annex B. EUT Internal Photos Model: YB-W4L EUT Internal View 1 EUT Internal View 2 FPCB Antenna Report No: SSP25100082-1&2&3E FCC ID: 2BKCP-YB-W4L Annex of Test Report EUT Internal View 3 EUT Internal View 4 Report No: SSP25100082-1&2&3E FCC ID: 2BKCP-YB-W4L Annex of Test Report EUT Internal View 5 EUT Internal View 6 Report No: SSP25100082-1&2&3E FCC ID: 2BKCP-YB-W4L Annex of Test Report EUT Internal View 7 EUT Internal View 8

FCC ID: 2BKCP-YB-W4L RF Exposure Evaluation Limits The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm2) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3–3.0 614 1.63 *(100) 6 3.0–30 1842/f 4.89/f *(900/f2) 6 30–300 61.4 0.163 1.0 6 300–1500 f/300 6 1500–100,000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f2) 30 30–300 27.5 0.073 0.2 30 300–1500 f/1500 30 1500–100,000 1.0 30 f = frequency in MHz Friis transmission formula: Pd = (Pout*G)/(4*pi*r2) Where Pd = power density in mW/cm2, Pout = output power to antenna in mW; G = gain of antenna in linear scale, Pi = 3.1416; R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm2. If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. Test Result of RF Exposure Evaluation BLE Mode Output power to antenna (dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result GFSK 0.13 1.03 0.0004 1.0 PASS 2.4G Wi-Fi Mode Output power to antenna (dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result 802.11ax(HE40) 14.73 29.72 0.0118 1.0 PASS 5.8G Wi-Fi Mode Output power to antenna (dBm) Output power to antenna (mW) Power Density at R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result 802.11ac(VHT20) 12.13 16.33 0.0065 1.0 PASS Remark: BT antenna gain=3dBi, 2.4G antenna gain=3dBi, 5G antenna gain=3dBi The device cannot transmit with 2.4G WI-FI and 5.8G WI-FI simultaneously, can transmit with 2.4G WI-FI, 5.8G WI-FI and BT simultaneously. Calculations for simultaneously transmit Mode Ratios Result Limit Result BLE 0.0004 0.0122 1 PASS 2.4G Wi-Fi 0.0118 Mode Ratios Result Limit Result BLE 0.0004 0.0069 1 PASS 5.8G Wi-Fi 0.0065 Ratios = Power Density / Power density Limit So a SAR test is not required

Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Test Data Appendix of Test Report 1. Duty Cycle Condition Mode Frequency (MHz) Antenna Duty Cycle (%) Correction Factor (dB) 1/T (kHz) NVNT a 5745 Ant1 64.38 1.91 4.1 NVNT a 5785 Ant1 75.08 1.24 4.1 NVNT a 5825 Ant1 77.22 1.12 4.1 NVNT n20 5745 Ant1 62.67 2.03 4.44 NVNT n20 5785 Ant1 48.7 3.12 4.44 NVNT n20 5825 Ant1 58.03 2.36 4.46 NVNT n40 5755 Ant1 43.69 3.6 7.81 NVNT n40 5795 Ant1 29.95 5.24 7.69 NVNT ac20 5745 Ant1 48.31 3.16 6.99 NVNT ac20 5785 Ant1 38.44 4.15 6.99 NVNT ac20 5825 Ant1 51.26 2.9 7.04 NVNT ac40 5755 Ant1 49.55 3.05 9.17 NVNT ac40 5795 Ant1 55.56 2.55 9.09 NVNT ax20 5745 Ant1 44.41 3.53 6.99 NVNT ax20 5785 Ant1 42.56 3.71 6.99 NVNT ax20 5825 Ant1 39.5 4.03 6.99 NVNT ax40 5755 Ant1 56.04 2.52 9.8 NVNT ax40 5795 Ant1 36.59 4.37 9.9 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Duty Cycle NVNT a 5745MHz Ant1 Duty Cycle NVNT a 5785MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Duty Cycle NVNT a 5825MHz Ant1 Duty Cycle NVNT n20 5745MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Duty Cycle NVNT n20 5785MHz Ant1 Duty Cycle NVNT n20 5825MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Duty Cycle NVNT n40 5755MHz Ant1 Duty Cycle NVNT n40 5795MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Duty Cycle NVNT ac20 5745MHz Ant1 Duty Cycle NVNT ac20 5785MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Duty Cycle NVNT ac20 5825MHz Ant1 Duty Cycle NVNT ac40 5755MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Duty Cycle NVNT ac40 5795MHz Ant1 Duty Cycle NVNT ax20 5745MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Duty Cycle NVNT ax20 5785MHz Ant1 Duty Cycle NVNT ax20 5825MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Duty Cycle NVNT ax40 5755MHz Ant1 Duty Cycle NVNT ax40 5795MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L 2. Maximum Conducted Output Power Condition Mode Frequency (MHz) Antenna Conducted Power (dBm) Duty Factor (dB) Total Power (dBm) Limit (dBm) Verdict NVNT a 5745 Ant1 7.4 1.91 9.31 30 Pass NVNT a 5785 Ant1 6.26 1.24 7.5 30 Pass NVNT a 5825 Ant1 5.6 1.12 6.72 30 Pass NVNT n20 5745 Ant1 6.52 2.03 8.55 30 Pass NVNT n20 5785 Ant1 6.25 3.12 9.37 30 Pass NVNT n20 5825 Ant1 5.43 2.36 7.79 30 Pass NVNT n40 5755 Ant1 5.88 3.6 9.48 30 Pass NVNT n40 5795 Ant1 4.43 5.24 9.67 30 Pass NVNT ac20 5745 Ant1 8.97 3.16 12.13 30 Pass NVNT ac20 5785 Ant1 7.75 4.15 11.9 30 Pass NVNT ac20 5825 Ant1 7.49 2.9 10.39 30 Pass NVNT ac40 5755 Ant1 8.07 3.05 11.12 30 Pass NVNT ac40 5795 Ant1 7.19 2.55 9.74 30 Pass NVNT ax20 5745 Ant1 5.34 3.53 8.87 30 Pass NVNT ax20 5785 Ant1 3.98 3.71 7.69 30 Pass NVNT ax20 5825 Ant1 2.98 4.03 7.01 30 Pass NVNT ax40 5755 Ant1 4.12 2.52 6.64 30 Pass NVNT ax40 5795 Ant1 3.1 4.37 7.47 30 Pass Note: Total power=Conducted power + Duty factor Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Power NVNT a 5745MHz Ant1 Power NVNT a 5785MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Power NVNT a 5825MHz Ant1 Power NVNT n20 5745MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Power NVNT n20 5785MHz Ant1 Power NVNT n20 5825MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Power NVNT n40 5755MHz Ant1 Power NVNT n40 5795MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Power NVNT ac20 5745MHz Ant1 Power NVNT ac20 5785MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Power NVNT ac20 5825MHz Ant1 Power NVNT ac40 5755MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Power NVNT ac40 5795MHz Ant1 Power NVNT ax20 5745MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Power NVNT ax20 5785MHz Ant1 Power NVNT ax20 5825MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Power NVNT ax40 5755MHz Ant1 Power NVNT ax40 5795MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L 3. -6dB Bandwidth Condition Mode Frequency (MHz) Antenna -6 dB Bandwidth (MHz) Limit -6 dB Bandwidth (MHz) Verdict NVNT a 5745 Ant1 16.47 0.5 Pass NVNT a 5785 Ant1 16.46 0.5 Pass NVNT a 5825 Ant1 16.45 0.5 Pass NVNT n20 5745 Ant1 17.65 0.5 Pass NVNT n20 5785 Ant1 17.62 0.5 Pass NVNT n20 5825 Ant1 17.72 0.5 Pass NVNT n40 5755 Ant1 36.35 0.5 Pass NVNT n40 5795 Ant1 36.41 0.5 Pass NVNT ac20 5745 Ant1 18.97 0.5 Pass NVNT ac20 5785 Ant1 19.06 0.5 Pass NVNT ac20 5825 Ant1 19.04 0.5 Pass NVNT ac40 5755 Ant1 36.41 0.5 Pass NVNT ac40 5795 Ant1 36.40 0.5 Pass NVNT ax20 5745 Ant1 18.97 0.5 Pass NVNT ax20 5785 Ant1 19.03 0.5 Pass NVNT ax20 5825 Ant1 19.00 0.5 Pass NVNT ax40 5755 Ant1 37.81 0.5 Pass NVNT ax40 5795 Ant1 37.97 0.5 Pass Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L -6dB Bandwidth NVNT a 5745MHz Ant1 -6dB Bandwidth NVNT a 5785MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L -6dB Bandwidth NVNT a 5825MHz Ant1 -6dB Bandwidth NVNT n20 5745MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L -6dB Bandwidth NVNT n20 5785MHz Ant1 -6dB Bandwidth NVNT n20 5825MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L -6dB Bandwidth NVNT n40 5755MHz Ant1 -6dB Bandwidth NVNT n40 5795MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L -6dB Bandwidth NVNT ac20 5745MHz Ant1 -6dB Bandwidth NVNT ac20 5785MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L -6dB Bandwidth NVNT ac20 5825MHz Ant1 -6dB Bandwidth NVNT ac40 5755MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L -6dB Bandwidth NVNT ac40 5795MHz Ant1 -6dB Bandwidth NVNT ax20 5745MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L -6dB Bandwidth NVNT ax20 5785MHz Ant1 -6dB Bandwidth NVNT ax20 5825MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L -6dB Bandwidth NVNT ax40 5755MHz Ant1 -6dB Bandwidth NVNT ax40 5795MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L 4. Occupied Channel Bandwidth Condition Mode Frequency (MHz) Antenna 99% OBW (MHz) NVNT a 5745 Ant1 16.599 NVNT a 5785 Ant1 16.636 NVNT a 5825 Ant1 16.637 NVNT n20 5745 Ant1 17.819 NVNT n20 5785 Ant1 17.785 NVNT n20 5825 Ant1 17.852 NVNT n40 5755 Ant1 36.384 NVNT n40 5795 Ant1 36.455 NVNT ac20 5745 Ant1 19.053 NVNT ac20…

Text truncated - open the document above for the full version.

Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L 5. Maximum Power Spectral Density Level Condition Mode Frequency (MHz) Antenna Conducted PSD (dBm/510kHz) Duty Factor (dB) 10log (510/500) Total PSD dBm/500kHz) Limit (dBm/500KHz) Verdict NVNT a 5745 Ant1 -5.82 1.91 0.086 -3.824 30 Pass NVNT a 5785 Ant1 -6.78 1.24 0.086 -5.454 30 Pass NVNT a 5825 Ant1 -7.44 1.12 0.086 -6.234 30 Pass NVNT n20 5745 Ant1 -6.05 2.03 0.086 -3.934 30 Pass NVNT n20 5785 Ant1 -7.2 3.12 0.086 -3.994 30 Pass NVNT n20 5825 Ant1 -7.76 2.36 0.086 -5.314 30 Pass NVNT n40 5755 Ant1 -9.57 3.6 0.086 -5.884 30 Pass NVNT n40 5795 Ant1 -11.13 5.24 0.086 -5.804 30 Pass NVNT ac20 5745 Ant1 -4.41 3.16 0.086 -1.164 30 Pass NVNT ac20 5785 Ant1 -5.44 4.15 0.086 -1.204 30 Pass NVNT ac20 5825 Ant1 -5.82 2.9 0.086 -2.834 30 Pass NVNT ac40 5755 Ant1 -7.39 3.05 0.086 -4.254 30 Pass NVNT ac40 5795 Ant1 -8.5 2.55 0.086 -5.864 30 Pass NVNT ax20 5745 Ant1 -4.08 3.53 0.086 -0.464 30 Pass NVNT ax20 5785 Ant1 -5.15 3.71 0.086 -1.354 30 Pass NVNT ax20 5825 Ant1 -6.11 4.03 0.086 -1.994 30 Pass NVNT ax40 5755 Ant1 -7.34 2.52 0.086 -4.734 30 Pass NVNT ax40 5795 Ant1 -8.21 4.37 0.086 -3.754 30 Pass Note: Total PSD=Conducted PSD + Duty factor+(10log(Test RBW/ Limit RBW) Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L PSD NVNT a 5745MHz Ant1 PSD NVNT a 5785MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L PSD NVNT a 5825MHz Ant1 PSD NVNT n20 5745MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L PSD NVNT n20 5785MHz Ant1 PSD NVNT n20 5825MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L PSD NVNT n40 5755MHz Ant1 PSD NVNT n40 5795MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L PSD NVNT ac20 5745MHz Ant1 PSD NVNT ac20 5785MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L PSD NVNT ac20 5825MHz Ant1 PSD NVNT ac40 5755MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L PSD NVNT ac40 5795MHz Ant1 PSD NVNT ax20 5745MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L PSD NVNT ax20 5785MHz Ant1 PSD NVNT ax20 5825MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L PSD NVNT ax40 5755MHz Ant1 PSD NVNT ax40 5795MHz Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L 6. Band Edge Condition Mode Frequency (MHz) Antenna Max Value (dBm) Verdict NVNT a 5745 Ant1 -30.88 Pass NVNT a 5825 Ant1 -40.79 Pass NVNT n20 5745 Ant1 -30.37 Pass NVNT n20 5825 Ant1 -40.53 Pass NVNT n40 5755 Ant1 -30.13 Pass NVNT n40 5795 Ant1 -38.51 Pass NVNT ac20 5745 Ant1 -17.62 Pass NVNT ac20 5825 Ant1 -27.89 Pass NVNT ac40 5755 Ant1 -20.85 Pass NVNT ac40 5795 Ant1 -28.45 Pass NVNT ax20 5745 Ant1 -17.64 Pass NVNT ax20 5825 Ant1 -30.09 Pass NVNT ax40 5755 Ant1 -17.62 Pass NVNT ax40 5795 Ant1 -29.65 Pass Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Band Edge NVNT a 5745MHz Low Ant1 Band Edge NVNT a 5825MHz High Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Band Edge NVNT n20 5745MHz Low Ant1 Band Edge NVNT n20 5825MHz High Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Band Edge NVNT n40 5755MHz Low Ant1 Band Edge NVNT n40 5795MHz High Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Band Edge NVNT ac20 5745MHz Low Ant1 Band Edge NVNT ac20 5825MHz High Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Band Edge NVNT ac40 5755MHz Low Ant1 Band Edge NVNT ac40 5795MHz High Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Band Edge NVNT ax20 5745MHz Low Ant1 Band Edge NVNT ax20 5825MHz High Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Band Edge NVNT ax40 5755MHz Low Ant1 Band Edge NVNT ax40 5795MHz High Ant1 Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L 7. Conducted RF Spurious Emission Condition Mode Frequency (MHz) Antenna Max Value (dBc) Limit (dBc) Verdict NVNT a 5745 Ant1 -31.84 -27 Pass NVNT a 5785 Ant1 -31.96 -27 Pass NVNT a 5825 Ant1 -31.34 -27 Pass NVNT n20 5745 Ant1 -31.67 -27 Pass NVNT n20 5785 Ant1 -31.79 -27 Pass NVNT n20 5825 Ant1 -31.79 -27 Pass NVNT n40 5755 Ant1 -31.57 -27 Pass NVNT n40 5795 Ant1 -31.99 -27 Pass NVNT ac20 5745 Ant1 -31.48 -27 Pass NVNT ac20 5785 Ant1 -31.79 -27 Pass NVNT ac20 5825 Ant1 -31.86 -27 Pass NVNT ac40 5755 Ant1 -31.71 -27 Pass NVNT ac40 5795 Ant1 -32.18 -27 Pass NVNT ax20 5745 Ant1 -31.05 -27 Pass NVNT ax20 5785 Ant1 -31.47 -27 Pass NVNT ax20 5825 Ant1 -32.23 -27 Pass NVNT ax40 5755 Ant1 -31.57 -27 Pass NVNT ax40 5795 Ant1 -32.19 -27 Pass Note: Testing is carried out with frequency rang 30MHz to the 40GHz, above 27GHz not recorded for no spurious point have a margin of less than 20dB with respect to the limits. Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Tx. Spurious NVNT a 5745MHz Ant1 Emission Tx. Spurious NVNT a 5785MHz Ant1 Emission Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Tx. Spurious NVNT a 5825MHz Ant1 Emission Tx. Spurious NVNT n20 5745MHz Ant1 Emission Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Tx. Spurious NVNT n20 5785MHz Ant1 Emission Tx. Spurious NVNT n20 5825MHz Ant1 Emission Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Tx. Spurious NVNT n40 5755MHz Ant1 Emission Tx. Spurious NVNT n40 5795MHz Ant1 Emission Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Tx. Spurious NVNT ac20 5745MHz Ant1 Emission Tx. Spurious NVNT ac20 5785MHz Ant1 Emission Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Tx. Spurious NVNT ac20 5825MHz Ant1 Emission Tx. Spurious NVNT ac40 5755MHz Ant1 Emission Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Tx. Spurious NVNT ac40 5795MHz Ant1 Emission Tx. Spurious NVNT ax20 5745MHz Ant1 Emission Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Tx. Spurious NVNT ax20 5785MHz Ant1 Emission Tx. Spurious NVNT ax20 5825MHz Ant1 Emission Report No: SSP25100082-3E FCC ID: 2BKCP-YB-W4L Tx. Spurious NVNT ax40 5755MHz Ant1 Emission Tx. Spurious NVNT ax40 5795MHz Ant1 Emission

Report No: SSP25100082-3E FCC Test Report Page 1 of 30 FCC TEST REPORT FCC ID: 2BKCP-YB-W4L Report No. : SSP25100082-3E Applicant : Shenzhen Yuben Technology CO, LTD Product Name : Smart Pet Feeder (with camera) Model Name : YB-W4L Test Standard : FCC Part 15 Subpart E Date of Issue : 2025-12-12 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.ccuttest.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: SSP25100082-3E FCC Test Report Page 2 of 30 Test Report Basic Information Applicant..................................: Shenzhen Yuben Technology CO, LTD Address of Applicant...............: E1, Floor 7, Building 13, Lehui Science and Technology Innovation Center, 489 Jihua Road, Bantian Street, Longgang District, Shenzhen, China Manufacturer..........................: Shenzhen Yuben Technology CO, LTD Address of Manufacturer........: E1, Floor 7, Building 13, Lehui Science and Technology Innovation Center, 489 Jihua Road, Bantian Street, Longgang…

Text truncated - open the document above for the full version.