2BKKQ-77-62ATOYS

the power button to turn on. There is an audio prompt when turning on or off, Electromagnetic Radiation Protection: This device is designed with a safe voltage of 4.5V, and its electromagnetic radiation meets children's safety standards. It is recommended to keep the device at an appropriate distance from the head when in use, avoid prolonged close contact with the ear, to reduce potential radiation exposure risk. Hearing Protection: The volume setting should be moderate to avoid hearing damage caused by excessively high volume. Children's ear canals are more delicate, and prolonged use may affect hearing health. It is recommended that single-use time does not exceed 30 minutes, and children's usage habits should be supervised. Parental Supervision: When 3-6 year old young children use the device, parents need to supervise throughout the process to prevent misoperation or unexpected situations. Although the device is designed to be safe, children may attempt dangerous behaviors out of curiosity, such as disassembling or swallowing small parts.

Shantou Chenghai District Enda Toy Factory Covered Equipment Certification Attestation Letter 1/22/2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2BKKQ-77-62A Shantou Chenghai District Enda Toy Factory (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Shantou Chenghai District Enda Toy Factory (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Shantou Chenghai District Enda Toy Factory (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Signed: Printed name: wang xi Title: Manager Company Name: Shantou Chenghai District Enda Toy Factory Date: 1/22/2026

Shantou Chenghai District Enda Toy Factory U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: January 22, 2026 Ref: Attestation Statement – Part 2.911(d)(7) filing FCC ID: 2BKKQ-77-62A Shantou Chenghai District Enda Toy Factory (“the applicant”) certifies that, as of the date of the filing of the application, CLF Import and Export Limited (“the agent”) is our designated U.S. agent for service of process for the above reference FCC ID. The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges it is our responsibility to inform the FCC whenever the agent information changes. CLF Import and Export Limited ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name: CLF Import and Export Limited FRN: 0033489683 Address: 1312 17th Street #692, Denver, CO 80202, United States Signature: Contact Person: David Chen Tel: +1 949 254 2565 Email: [email protected] Applicant Company Name: Shantou Chenghai District Enda Toy Factory FRN: 0035867241 Address: Dongxingyuan Industrial Zone,Huaidong Village, Lianxia Town, Chenghai District, Shantou City China 515800 Signature: Contact Person: wang xi Tel: 13750461699 Email: [email protected]

DATE: January 22, 2026 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen CCUT Quality Technology Co., Ltd. (1F, Building 35, Changxing Technology Indstrl Park Changzhen Community, Yutang Street,Shenzhen,China) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Shantou Chenghai District Enda Toy Factory (Dongxingyuan Industrial Zone,Huaidong Village, Lianxia Town, Chenghai District, Shantou City China 515800). <Signature> Name: wang xi Title: Sales Manager Company: Shantou Chenghai District Enda Toy Factory

Date: January 22, 2026 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, <Signature> Name: wang xi Title: Sales Manager Company: Shantou Chenghai District Enda Toy Factory

DATE: January 22, 2026 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BKKQ-77-62A Product Name: TOYS Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...) • Schematics • Block diagram • Operation description • BOM • tune up These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name: wang xi Title: Sales Manager Company: Shantou Chenghai District Enda Toy Factory

Shantou Chenghai District Enda Toy Factory Model Difference Statement FCC ID: 2BKKQ-77-62A DATE: January 22, 2026 Dear Sir/Madam, Added models 77-63A, 77-64A, 77-65A, 77-66A basis of the original product 77-62A.The color of appearance and model name of series models listed are different from the main model, but the circuit and the electronic construction are the same, declared by the manufacturer. Sincerely, <Signature> Name: wang xi Title: Sales Manager Company: Shantou Chenghai District Enda Toy Factory

Report No.: AB26010320FW01 Page 1 of 4 Appendix E EUT External Photos Report No.: AB26010320FW01 Page 2 of 4 Report No.: AB26010320FW01 Page 3 of 4 Report No.: AB26010320FW01 Page 4 of 4

Label and Information FCC Label Sample FCC Labe Size: 0.5cm x 0.5cm FCC Label Specifications Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Where the EUT is constructed in two or more sections connected by wires and marketed together, the above statement is required to be affixed only to the main control unit. When the EUT is so small or for such use that it is not practicable to place the statement on it, the above information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. FCC Label Location Label Location

Report No.: AB26010320FW01 Page 1 of 3 Appendix F Internal Photos Integral ANT Report No.: AB26010320FW01 Page 2 of 3 Report No.: AB26010320FW01 Page 3 of 3

FCC ID: 2BKKQ-77-62A RF Exposure Evaluation According to KDB 447498 D01 General RF Exposure Guidance v06 and part 2.1093，Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison Here, The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. For 462.5625MHz Max Conducted Power(dBm) Tune-up Power(dBm) Max Tune-up Power(dBm) Max Power(mW) Frequency(MHz) Min. distance(mm) Calc. thresholds limit 7.5 7(±1) 8 6.31 462.5625 5 0.858310 3.0 So a SAR test is not required

Report No.: AB26010320FW01 Aibo Standard Technology (Shenzhen) Co., Ltd. 101, Building B, Tuori New Energy Industrial Park, High-tech Park, Tianliao Community, Yutang Street, Guangming District, Shenzhen City, Guangdong Province, China Tel.: +86 755 85250797 E-mail: [email protected] Website: www.aibonorm.com FCC TEST REPORT Report No. ........................................ : AB26010320FW01 FCC ID.............................................. : 2BKKQ-77-62A Applicant ........................................... : Shantou Chenghai District Enda Toy Factory Address ............................................ : Dongxingyuan Industrial Zone,Huaidong Village, Lianxia Town, Chenghai District, Shantou City China 515800 Manufacturer......................................: Shantou Chenghai District Enda Toy Factory Address..............................................: Dongxingyuan Industrial Zone,Huaidong Village, Lianxia Town, Chenghai District, Shantou City China 515800 Product Name .................................. : TOYS Trade Mark ....................................... : N/A Test Model ........................................ : 77-62A Additional Model(s) ........................... : 77-63A, 77-64A, 77-65A, 77-66A Standard ........................................... : FCC Part 95 Subpart B ANSI C63.26-2015 ANSI/TIA-603-D 2010 Date of Receipt ................................. : 2025-12-07 Date of Test Date .............................. : 2025-12-07-2026-01-08 Date of Issue .................................... : 2026-01-08 Test Result ........................................ : Pass Compiled by: (Printed Name + Signature) Huaijie Li Supervised by: (Printed Name + Signature) David Huang Approved by: (Printed Name + Signature) Jay Liu Testing Laboratory Name ................. : Aibo Standard Technology (Shenzhen) Co., Ltd. Address ............................................ : 101, Building B, Tuori New Energy Industrial Park, High-tech Park, Tianliao Community, Yutang Street, Guangming District, Shenzhen City, Guangdong Province, China This test report may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by Aibo. The test results in the report only apply to the tested sample. The test report shall be invalid without all the signatures of testing engineers, reviewer and approver. Any objections must be raised to Aibo within 15 days since the date when the report is received. It will not be taken into consideration beyond this limit. The test report merely correspond to the test sample. Report No.: AB26010320FW01 Page 2 of 24 Aibo Standard Technology (Shenzhen) Co., Ltd. FCC TEST REPORT Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. REPORT VERSION Version No. Issue Date Description 01 2026-01-08 Initial Issue EUT......................................... : TOYS Test Model.............................. : 77-62A Applicant............................... : Shantou Chenghai District Enda Toy Factory Address................................... : Dongxingyuan Industrial Zone,Huaidong Village, Lianxia Town, Chenghai District, Shantou City China 515800 Manufacturer......................... : Shantou Chenghai District Enda Toy Factory Address................................... : Dongxingyuan Industrial Zone,Huaidong Village, Lianxia Town, Chenghai District, Shantou City China 515800 Report No.: AB26010320FW01 Page 3 of 24 Aibo Standard Technology (Shenzhen) Co., Ltd. CONTENTS 1. GENERAL INFORMATION ....................................................................................................................................... 4 1.1. GENERAL DESCRIPTION OF EUT ..................................................................................................................................... 4 1.2. DESCRIPTION OF SUPPORT EQUIPMENT ....................................................................................................................... 5 1.3. DESCRIPTION OF EXTERNAL I/O ..................................................................................................................................... 5 1.4. GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................................................................... 6 1.5. DESCRIPTION OF TEST FACILITY ..................................................................................................................................... 6 1.6. MEASUREMENT UNCERTAINTY ..................................................................................................................................... 7 1.7. ENVIRONMENTAL CONDITIONS..................................................................................................................................... 7 1.8. DESCRIPTION OF TEST MODES ....................................................................................................................................... 8 1.9. SUMMARY OF TEST RESULT ........................................................................................................................................... 9 1.10. MEASUREMENT INSTRUMENTS LIST .............................................................................................................. 9 4. ANTENNA REQUIREMENT ................................................................................................................................... 10 4.1 STANDARD AND LIMIT ................................................................................................................................................... 10 4.2 TEST RESULTS ...............................................................................................................…

Text truncated - open the document above for the full version.

Report No.: AB26010320FW01 Page 1 of 2 Appendix D Test Photos Radiated Emission Test View Below 1GHz Report No.: AB26010320FW01 Page 2 of 2 Radiated Emission Test View Above 1GHz