2BKWR-T500ADIBO intelligent tennis ball machine

FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ·Reorient or relocate the receiving antenna. ·Increase the separation between the equipment and receiver. ·Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ·Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Covered Equipment Attestation Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(5)(i)-(ii) of the Commission’s Rules (47 C.F.R.) we attest as follows for the product listed below: FCC ID Model name 2BKWR-T500 T500 We, Applicant Company Name: Aidibao Sporting Goods (Shenzhen) Co., LTD Address: Room 305, Floor 3, Building 2, Huisengda Factory Building, No. 29, Qingcui Road.nity, Longhua Street, Longhua District, Shenzhen, China Phone: +86-18927496396 certify that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. This includes the cybersecurity and anti-virus software produced or provided by Kaspersky Lab, Inc. We certify that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. If you have any questions, please feel free to contact us at the address shown below. Sincerely, 2024-09-25 Signature Date Name / Title: Yehua Qin / Quality Manager Company: Aidibao Sporting Goods (Shenzhen) Co., LTD Address: Room 305, Floor 3, Building 2, Huisengda Factory Building, No. 29, Qingcui Road.nity, Longhua Street, Longhua District, Shenzhen, China Phone: +86-18927496396 Fax: N/A E-Mail: [email protected]

Confidentiality Request Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we request confidentiality for the documentation of the following products: FCC ID Model name 2BKWR-T500 T500 For the products listed above, we request permanent confidentiality for all applicable exhibits as there are: • the Operational Description • the Block Diagram • the Schematics • the Part List • the Tune up Information The above listed exhibits contain trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact us at the address shown below. Sincerely, 2024-09-25 Signature Date Name / Title: Yehua Qin / Quality Manager Company: Aidibao Sporting Goods (Shenzhen) Co., LTD Address: Room 305, Floor 3, Building 2, Huisengda Factory Building, No. 29, Qingcui Road.nity, Longhua Street, Longhua District, Shenzhen, China Phone: +86-18927496396 Fax: N/A E-Mail: [email protected]

FCC ID: 2BKWR-T500 Fig. 1 Fig. 2 FCC ID: 2BKWR-T500 Fig. 3 Fig. 4 FCC ID: 2BKWR-T500 Fig. 5 Fig. 6 FCC ID: 2BKWR-T500 Fig. 7 Fig. 8

_____________________________________________________________________________________________________ LABEL AND LOCATION (Size: L6.0cm x 4.0cm) Label Location

FCC ID: 2BKWR-T500 Fig. 1 Fig. 2 BLE Antenna FCC ID: 2BKWR-T500 Fig. 3 Fig. 4 FCC ID: 2BKWR-T500 Fig. 5 Fig. 6 BLE Antenna (Disables) FCC ID: 2BKWR-T500 Fig. 7 Fig. 8 BLE Antenna (Disables)

Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao‟an District, Shenzhen, China RF Exposure evaluation Report Reference No. .................... : FCC ID. ............................................ : CTA24082101002 2BKWR-T500 Compiled by ( position+printed name+signature) .. : File administrators Jinghua Xiao Supervised by ( position+printed name+signature) .. : Test Engineer Lushan Kong Approved by ( position+printed name+signature) .. : Manager Eric Wang Date of issue ..................................... : Aug.23, 2024 Representative Laboratory Name : Shenzhen CTA Testing Technology Co., Ltd. Address ............................................. : Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao„an District, Shenzhen, China Applicant’s name ............................ : Aidibao Sporting Goods (Shenzhen) Co., LTD Address ............................................. : Room 305, Floor 3, Building 2, Huisengda Factory Building, No. 29, Qingcui Road.nity, Longhua Street, Longhua District, Shenzhen, China Test specification .......................... : Standard ........................................... : 47CFR §1.1310 47CFR §2.1093 KDB447498 D01 General RF Exposure Guidance v06 TRF Originator .................................. : Shenzhen Global Test Service Co.,Ltd. Master TRF ....................................... : Dated 2014-12 Shenzhen CTA Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTA Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTA Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .................... : ADIBO intelligent tennis ball machine Trade Mark ....................................... : N/A Manufacturer ..................................... : Aidibao Sporting Goods (Shenzhen) Co., LTD Model/Type reference ....................... : T500 Listed Models ................................... : N/A Exposure category ............................ : General population/uncontrolled environment EUT Type .......................................... : ADIBO intelligent tennis ball machine Hardware Version ............................ : N/A Software Version .............................. : N/A Rating ............................................... : DC 29.4V /5.0 A by Adapter Result ................................................ : PASS Report No.: CTA24052001102 Page 2 of 10 T E S T R E P O R T Test Report No. : CTA24082101002 Aug.23, 2024 ______________________________________________________________________________________________ Date of issue Equipment under Test : ADIBO intelligent tennis ball machine Model /Type : T500 Listed model : N/A Applicant : Aidibao Sporting Goods (Shenzhen) Co., LTD Address : Room 305, Floor 3, Building 2, Huisengda Factory Building, No. 29, Qingcui Road.nity, Longhua Street, Longhua District, Shenzhen, China Manufacturer : Aidibao Sporting Goods (Shenzhen) Co., LTD Address : Room 305, Floor 3, Building 2, Huisengda Factory Building, No. 29, Qingcui Road.nity, Longhua Street, Longhua District, Shenzhen, China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: CTA24052001102 Page 3 of 10 Contents 1. S U M M A R Y .................................................................................. 4 1.1. EUT configuration ....................................................................................................................................... 4 1.2. Product Description .................................................................................................................................... 4 2. T E S T E N V I R O N M E N T ................................................................... 5 2.1. Address of the test laboratory ................................................................................................................... 5 2.2. Test Facility .................................................................................................................................................. 5 2.3. Environmental conditions .......................................................................................................................... 5 2.4. Statement of the measurement uncertainty ............................................................................................. 5 3 . M E T H O D O F M E A S U R EM E N T ......................................................... 6 3.1. Applicable Standard .................................................................................................................................... 6 3.2. Evaluation Method and Limit...................................................................................................................... 6 4. C O N D U C T E D P O W E R R E S U L T S ...................................................... 7 5. M A N U F A C T U R I N G T O L E R ANCE ...................................................... 8 6 . E V A L U A T I O N R E S U L TS ................................................................ 9 6.1. Standalone Evaluation ................................................................................................................................ 9 7. C O N C L U S I O N ............................................................................ 10 Report No.: CTA24052001102 Page 4 of 10 1. S U M M A R Y 1.1. EUT configuration The following peripheral devices and interface cables were connected during the measurement: ● - supplied …

Text truncated - open the document above for the full version.

2.4 GHz RF Antenna with SMA Connector Product Number: AN2400-0101RS Page 1 1. Feature and Application . dipole antenna design . small size / high gain / omni-directional radiation pattern . IEEE 802.11 b / g WLAN AP (Access Point) application . Bluetooth / HomeRF / ISM Band and other 2.4 GHz wireless communication application 2. Specification 1. Frequency Range 2400 ~ 2500 MHz 2. V.S.W.R. < 2.0 3. Antenna Gain 2.0 dBi 4. Antenna Radiation Pattern Omni-directional 5. Impedance 50 ohm 6. Color of Outer Cover Black 7. Material of Outer Cover TPE 8. Material of Hinge PC 9. Operation Temperature -40 ̊C ~ + 90 ̊C 10. Storage Temperature -30 ̊C ~ + 75 ̊C Manufacturer Aidibao Sporting Goods (Shenzhen) Co., LTD Address Room 305, Floor 3, Building 2, Huisengda Factory Building, No. 29, Qingcui Road.nity, Longhua Street, Longhua District, Shenzhen, China 2.4 GHz RF Antenna with SMA Connector Product Number: AN2400-0101RS Page 2 3. S11 Return Loss Testing Data 4. V.S.W.R Testing Data 2.4 GHz RF Antenna with SMA Connector Product Number: AN2400-0101RS Page 3 5. Smith Chart and Impedance Testing Data 2.4 GHz RF Antenna with SMA Connector Product Number: AN2400-0101RS Page 4 6. Antenna Radiation Pattern --- Horizontal Plane --- Vertical Plane 2.4 GHz RF Antenna with SMA Connector Product Number: AN2400-0101RS Page 5 7. Mechanical Dimension Drawing 2.4 GHz RF Antenna with SMA Connector Product Number: AN2400-0101RS Page 6 8. Outer Cover Material Specification of TPE/TFE 2.4 GHz RF Antenna with SMA Connector Product Number: AN2400-0101RS Page 7 9. Hinge Material Specification of PC 2.4 GHz RF Antenna with SMA Connector Product Number: AN2400-0101RS Page 8 2.4 GHz RF Antenna with SMA Connector Product Number: AN2400-0101RS Page 9 10. Coaxial Cable RG-178 Data Sheet RG-178 Coaxial Cable Specification 1. Cable Type MIL – C – 17 / RG-178 2. Impedance 50 ± 3 ohm 3. Inner Conductor Material silver-coated cooper Conductor Numbers 7 Conductor Size 0.102 mm Outer Diameter 0.3 mm 4. Dielectric Layer Material FEP Color Clear Average Thickness 0.28 mm Diameter 0.86 mm 5. Braid (Shielding) Material silver-coated cooper Construction 16-3-0.1 mm Coverage 95 % 6. Outer Cover Material FEP Color Brown Average Thickness 0.25 mm Diameter 1.80 ± 0.05 mm 7. V.S.W.R Testing (DC ~ 6GHz) < 1.3 8. Attenuation (dB / 100 meter ) 100 MHz 46 900 MHz 155 1800 MHz 295 2400 MHz 340 5200 MHz 505 6000 MHz 550 9. Capacitance 97 ± 3 ( pF / meter) 10. Maximum Power 30 dBm 11. Spark Test 2.0 KV 12. Rating Temp. and Voltage 200 ̊C / 30V 13. Conductor Resistance 335 ohm / KM / 20 ̊C max. 14. Dielectric Resistance 3 G ohm / KM / 20 ̊C min. 2.4 GHz RF Antenna with SMA Connector Product Number: AN2400-0101RS Page 10 11. Reliability Testing on Antenna Body Test Item Procedure Requirement 1. Visual inspection and dimension check Applicable methods using x5 magnification follow Specification 2. Rapid changing of temperature -40 ̊C (30minutes) to 90 ̊C (30minutes); 120 cycles After 2 hours recovery: 1. no visible damage 2. bandwidth tolerance < ±5% 3. Damp Heat 500 hours at 60 ̊C; 90 ~ 95% RH After 2 hours recovery: 1. no visible damage 2. bandwidth tolerance < ±5% 4. Endurance 500 hours at 90 ̊C After 2 hours recovery: 1. no visible damage 2. bandwidth tolerance < ±5% 12. Ordering Information Part Number: AN 2400 – 01 01 RS Product Type AN= Antenna Frequency Code 2400= 2400 ~ 2500 MHz Dimension Code 01= see the mechanical drawing page Cable Code 01= RG-178 Connector Code RS= SMA male reverse 0S= SMA male

FCC ID: 2BKWR-T500 1 Case No. : CTA24082101001 Ambient Condition: 22 °C, 53 %RH According Standard: ■Part15C Test Date: 2024.8.15 Test Engineer: Lushan Kong Appendix A.1: DTS Bandwidth Test Result BT LE: TestMode Antenna Freq(MHz) DTS BW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict BLE Ant1 2402 0.684 2401.664 2402.348 0.5 PASS 2440 0.680 2439.668 2440.348 0.5 PASS 2480 0.648 2479.680 2480.328 0.5 PASS BT 2LE: TestMode Antenna Freq(MHz) DTS BW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict BLE Ant1 2402 1.344 2401.332 2402.676 0.5 PASS 2440 1.476 2439.204 2440.680 0.5 PASS 2480 1.580 2479.184 2480.764 0.5 PASS FCC ID: 2BKWR-T500 2 Test Graphs BT LE: BLE_Ant1_2402 BLE_Ant1_2440 BLE_Ant1_2480 FCC ID: 2BKWR-T500 3 FCC ID: 2BKWR-T500 4 BT 2LE: BLE_Ant1_2402 BLE_Ant1_2440 BLE_Ant1_2480 FCC ID: 2BKWR-T500 5 FCC ID: 2BKWR-T500 6 Appendix A.2: Occupied Channel Bandwidth Test Result BT LE: TestMode Antenna Freq(MHz) OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict BLE Ant1 2402 1.0901 2401.4557 2402.5458 --- --- 2440 1.0977 2439.4541 2440.5518 --- --- 2480 1.1017 2479.4485 2480.5502 --- --- BT 2LE: TestMode Antenna Freq(MHz) OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict BLE Ant1 2402 2.5898 2400.7215 2403.3113 --- --- 2440 2.6909 2438.7086 2441.3995 --- --- 2480 2.7381 2478.6796 2481.4177 --- --- FCC ID: 2BKWR-T500 7 Test Graphs BT LE: BLE_Ant1_2402 BLE_Ant1_2440 BLE_Ant1_2480 FCC ID: 2BKWR-T500 8 FCC ID: 2BKWR-T500 9 BT 2LE: BLE_Ant1_2402 BLE_Ant1_2440 BLE_Ant1_2480 FCC ID: 2BKWR-T500 10 FCC ID: 2BKWR-T500 11 Appendix A.3: Maximum conducted output power Test Result Peak BT LE: TestMode Antenna Freq(MHz) Conducted Peak Powert[dBm] Conducted Limit[dBm] Verdict BLE Ant1 2402 -3.69 ≤30 PASS 2440 -3.42 ≤30 PASS 2480 -1.85 ≤30 PASS BT 2LE: TestMode Antenna Freq(MHz) Conducted Peak Powert[dBm] Conducted Limit[dBm] Verdict BLE Ant1 2402 -3.77 ≤30 PASS 2440 -3.38 ≤30 PASS 2480 -1.88 ≤30 PASS FCC ID: 2BKWR-T500 12 Appendix A.4: Maximum power spectral density Test Result BT LE: TestMode Antenna Freq(MHz) Result[dBm/3kHz] Limit[dBm/3kHz] Verdict BLE Ant1 2402 -17.73 ≤8.00 PASS 2440 -17.54 ≤8.00 PASS 2480 -15.84 ≤8.00 PASS BT 2LE: TestMode Antenna Freq(MHz) Result[dBm/3kHz] Limit[dBm/3kHz] Verdict BLE Ant1 2402 -21.35 ≤8.00 PASS 2440 -21.30 ≤8.00 PASS 2480 -19.69 ≤8.00 PASS FCC ID: 2BKWR-T500 13 Test Graphs BT LE: BLE_Ant1_2402 BLE_Ant1_2440 BLE_Ant1_2480 FCC ID: 2BKWR-T500 14 FCC ID: 2BKWR-T500 15 BT 2LE: BLE_Ant1_2402 BLE_Ant1_2440 BLE_Ant1_2480 FCC ID: 2BKWR-T500 16 FCC ID: 2BKWR-T500 17 Appendix A.5: Band edge measurements Test Result BT LE: TestMode Antenna ChName Freq(MHz) RefLevel[dBm] Result[dBm] Limit[dBm] Verdict BLE Ant1 Low 2402 -4.83 -45.78 ≤-24.83 PASS High 2480 -2.91 -44.49 ≤-22.91 PASS BT 2LE: TestMode Antenna ChName Freq(MHz) RefLevel[dBm] Result[dBm] Limit[dBm] Verdict BLE Ant1 Low 2402 -6.28 -31.16 ≤-26.28 PASS High 2480 -4.64 -33.8 ≤-24.64 PASS FCC ID: 2BKWR-T500 18 Test Graphs BT LE: BLE_Ant1_Low_2402 BLE_Ant1_High_2480 FCC ID: 2BKWR-T500 19 BT 2LE: BLE_Ant1_Low_2402 BLE_Ant1_High_2480 FCC ID: 2BKWR-T500 20 Appendix A.6: Conducted Spurious Emission Test Result BT LE: TestMode Antenna Freq(MHz) FreqRange [MHz] RefLevel [dBm] Result[dBm] Limit[dBm] Verdict BLE Ant1 2402 Reference -5.60 -5.60 --- PASS 30~1000 -5.60 -60.31 ≤-25.6 PASS 1000~26500 -5.60 -47.98 ≤-25.6 PASS 2440 Reference -5.44 -5.44 --- PASS 30~1000 -5.44 -59.3 ≤-25.44 PASS 1000~26500 -5.44 -48.16 ≤-25.44 PASS 2480 Reference -3.02 -3.02 --- PASS 30~1000 -3.02 -60.13 ≤-23.02 PASS 1000~26500 -3.02 -47.34 ≤-23.02 PASS BT 2LE: TestMode Antenna Freq(MHz) FreqRange [MHz] RefLevel [dBm] Result[dBm] Limit[dBm] Verdict BLE Ant1 2402 Reference -6.94 -6.94 --- PASS 30~1000 -6.94 -37.01 ≤-26.94 PASS 1000~26500 -6.94 -47.37 ≤-26.94 PASS 2440 Reference -6.84 -6.84 --- PASS 30~1000 -6.84 -59.96 ≤-26.84 PASS 1000~26500 -6.84 -47.35 ≤-26.84 PASS 2480 Reference -5.32 -5.32 --- PASS 30~1000 -5.32 -33.06 ≤-25.32 PASS 1000~26500 -5.32 -48.08 ≤-25.32 PASS FCC ID: 2BKWR-T500 21 Test Graphs BT LE: BLE_Ant1_2402_0~Reference BLE_Ant1_2402_30~1000 BLE_Ant1_2402_1000~26500 FCC ID: 2BKWR-T500 22 BLE_Ant1_2440_0~Reference BLE_Ant1_2440_30~1000 FCC ID: 2BKWR-T500 23 BLE_Ant1_2440_1000~26500 BLE_Ant1_2480_0~Reference BLE_Ant1_2480_30~1000 FCC ID: 2BKWR-T500 24 BLE_Ant1_2480_1000~26500 FCC ID: 2BKWR-T500 25 BT 2LE: BLE_Ant1_2402_0~Reference BLE_Ant1_2402_30~1000 BLE_Ant1_2402_1000~26500 FCC ID: 2BKWR-T500 26 BLE_Ant1_2440_0~Reference BLE_Ant1_2440_30~1000 FCC ID: 2BKWR-T500 27 BLE_Ant1_2440_1000~26500 BLE_Ant1_2480_0~Reference BLE_Ant1_2480_30~1000 FCC ID: 2BKWR-T500 28 BLE_Ant1_2480_1000~26500 FCC ID: 2BKWR-T500 29 Appendix A.7: Emissions in Restricted Bands Test Result BT LE: TestMode Antenna ChName Freq(MHz ) Detector Freq [MHz] Result [dBm] Limit [dBm] Result [dBuV/m] Limit [dBuV/m] Verdict BLE Ant1 Low 2402 AV 2310.000 -49.6 ≤-41.20 45.60 ≤54 PASS AV 2378.015 -47.77 ≤-41.20 47.43 ≤54 PASS AV 2390.000 -48.73 ≤-41.20 46.47 ≤54 PASS Peak 2310.000 -43.82 ≤-21.20 51.38 ≤74 PASS Peak 2377.700 -40.02 ≤-21.20 55.18 ≤74 PASS Peak 2390.000 -40.49 ≤-21.20 54.71 ≤74 PASS High 2480 AV 2483.500 -42.14 ≤-41.20 53.06 ≤54 PASS AV 2483.520 -42.14 ≤-41.20 53.06 ≤54 PASS AV 2500.000 -48.64 ≤-41.20 46.56 ≤54 PASS Peak 2483.500 -35.49 ≤-21.20 59.71 ≤74 PASS Peak 2483.760 -34.83 ≤-21.20 60.37 ≤74 PASS Peak 2500.000 -44.9 ≤-21.20 50.30 ≤74 PASS BT 2LE: TestMode Antenna ChName Freq(MHz ) Detector Freq [MHz] Result [dBm] Limit [dBm] Result [dBuV/m] Limit [dBuV/m] Verdict BLE Ant1 Low 2402 AV 2310.000 -49.48 ≤-41.20 45.72 ≤54 PASS AV 2378.225 -48.03 ≤-41.20 47.17 ≤54 PASS AV 2390.000 -48.41 ≤-41.20 46.79 ≤54 PASS Peak 2310.000 -45.76 ≤-21.20 49.44 ≤74 PASS Peak 2352.605 -39.45 ≤-21.20 55.75 ≤74 PASS Peak 2390.000 -43.71 ≤-21.20 51.49 ≤74 PASS High 2480 AV 2483.500 -29.19 ≤-41.20 66.01 ≤54 PASS AV 2483.520 -29.19 ≤-41.20 66.01 ≤54 PASS AV 2500.000 -48.66 ≤-41.20 46.54 ≤54 PASS Peak 2483.500 -23.38 ≤-21.20 71.82 ≤74 PASS Peak 2483.760 -22.96 ≤-21.20 72.24 ≤74 PASS Peak 2500.000 -44.1 ≤-21.20 51.10 …

Text truncated - open the document above for the full version.

Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao‟an District, Shenzhen, China FCC PART 15 SUBPART C TEST REPORT FCC PART 15.247 Report Reference No. ..................... : FCC ID............................................. : CTA24082101001 2BKWR-T500 Compiled by ( position+printed name+signature) . : File administrators Jinghua Xiao Supervised by ( position+printed name+signature) . : Test Engineer Lushan Kong Approved by ( position+printed name+signature) . : Manager Eric Wang Date of issue .................................... : Aug.23, 2024 Representative Laboratory Name . : Shenzhen CTA Testing Technology Co., Ltd. Address ............................................ : Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao„an District, Shenzhen, China Applicant’s name ............................ : Aidibao Sporting Goods (Shenzhen) Co., LTD Address ............................................ : Room 305, Floor 3, Building 2, Huisengda Factory Building, No. 29, Qingcui Road.nity, Longhua Street, Longhua District, Shenzhen, China Test specification ........................... : Standard ........................................... : FCC Part 15.247 TRF Originator .................................. : Shenzhen Global Test Service Co.,Ltd. Master TRF ...................................... : Dated 2014-12 Shenzhen CTA Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTA Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTA Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description ..................... : ADIBO intelligent tennis ball machine Trade Mark ....................................... : N/A Manufacturer .................................... : Aidibao Sporting Goods (Shenzhen) Co., LTD Model/Type reference ...................... : T500 Listed Models .................................. : N/A Modulation Type ............................... : GFSK Operation Frequency ........................ : From 2402MHz to 2480MHz Hardware Version ............................ : N/A Software Version .............................. : N/A Rating ............................................... : DC 29.4V /5.0 A by Adapter Result ............................................... : PASS Report No.: CTA24082101001 Page 2 of 35 T E S T R E P O R T Test Report No. : CTA24082101001 Aug.23, 2024 ______________________________________________________________________________________________ Date of issue Equipment under Test : ADIBO intelligent tennis ball machine Model /Type : T500 Listed model : N/A Applicant : Aidibao Sporting Goods (Shenzhen) Co., LTD Address : Room 305, Floor 3, Building 2, Huisengda Factory Building, No. 29, Qingcui Road.nity, Longhua Street, Longhua District, Shenzhen, China Manufacturer : Aidibao Sporting Goods (Shenzhen) Co., LTD Address : Room 305, Floor 3, Building 2, Huisengda Factory Building, No. 29, Qingcui Road.nity, Longhua Street, Longhua District, Shenzhen, China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: CTA24082101001 Page 3 of 35 Contents 1. TEST STANDARDS ......................................................................................................................................... 4 2. SUMMARY ....................................................................................................................................................... 5 2.1. General Remarks ................................................................................................................................... 5 2.2. Product Description ................................................................................................................................ 5 2.3. Equipment Under Test ........................................................................................................................... 6 2.4. Short description of the Equipment under Test (EUT) ........................................................................... 6 2.5. EUT operation mode .............................................................................................................................. 6 2.6. Block Diagram of Test Setup ................................................................................................................. 7 2.7. EUT Exercise Software .......................................................................................................................... 7 2.8. Special Accessories ............................................................................................................................... 7 2.9. External I/O Cable .................................................................................................................................. 7 2.10. Related Submittal(s) / Grant (s) ........................................................................................................... 7 2.11. Modifications ........................................................................................................................................ 7 3. TEST ENVIRONMENT ..................................................................................................................................... 8 3.1. Address of the test laboratory ................................................................................................................ 8 3.2. Test Facility ..........................................................................................…

Text truncated - open the document above for the full version.

FCC ID: 2BKWR-T500 _______________________________________________________________________________________________ Page 1 of 2 1. TEST SETUP PHOTOGRAPHS 1.1. Photo of Radiated Emissions Measurement Fig. 1 Fig. 2 FCC ID: 2BKWR-T500 _______________________________________________________________________________________________ Page 2 of 2 Photo of Conducted Emission Measurement Fig. 3