2BKZ6-REBADGE2Rebadge

Rebadge2 QuickStart Guide CONNECT READ WRITE PUSH BUTTON TO TURN ON PROBLEM: NO POWER LED SOLUTION: CHARGE DEVICE PUSH BUTTON TO TURN ON ON TELEPHONE 1. ENABLE BLUETOOTH 2. OPEN REBADGE APP 3. CONNECT REBADGE2 PROBLEM: CANNOT CONNECT SOLUTION: - CHECK POWER IS ON - CHECK BLUE LED IS FLASHING - ENABLE BLUETOOTH ON PHONE - ENABLE LOCATION SERVICES IN APPLICATION IN REBADGE APP PRESS READ BUTTON IN REBADGE APP PRESS WRITE BUTTON BADGE COPY COMPLETE GREEN LED: POWER ON FLASHING BLUE LED: WAITING CONNECTION PROBLEM: RED LED SOLUTION: CHARGE DEVICE PINK LED FLASHING: READING BADGE PINK LED FLASHING: WRITING BADGE Rebadge2 App Rebadge2 App Rebadge2 App Rebadge2 App Rebadge2 App FINISHED CIRCLE-CHECK Connect Device Troubleshoot Copy Badge circle-question FCC Warning 15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement: 1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2.This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 5mm between the radiator and your body.

JMA ALEJANDRO ALTUNA, S.L.U. 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – Equipment Type Company name: JMA ALEJANDRO ALTUNA, S.L.U. Address: Bidekurtzeta 6, 20500 Arrasate Gipuzkoa Spain Product Name: Rebadge FCC ID: 2BKZ6-REBADGE2 Model(s): Rebadge 2 2.911(d)(5)(i) Equipment Type We, [JMA ALEJANDRO ALTUNA, S.L.U.] (“the applicant”) certify that the equipment for which authorization is sought through certification is not:  Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules.  Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Ivy Wang Date: 2024-09-25 Title and Company name: sales NOTE 1 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

JMA ALEJANDRO ALTUNA, S.L.U. 2.911 (d)(5)(ii) Applicant Attestation v1.2 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: JMA ALEJANDRO ALTUNA, S.L.U. Address: Bidekurtzeta 6, 20500 Arrasate Gipuzkoa Spain Product Name: Rebadge FCC ID: 2BKZ6-REBADGE2 Model(s): Rebadge 2 2.911(d)(5)(ii) Applicant filing We, [JMA ALEJANDRO ALTUNA, S.L.U. ] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 , established pursuant to § 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name: Ivy Wang Date: 2024-09-25 Title and Company name: sales NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

JMA ALEJANDRO ALTUNA, S.L.U. 2.911 (d)(7)USA Agent v1.2 Section 2.911(d)(7) USA Agent for Service of Process Company name: JMA ALEJANDRO ALTUNA, S.L.U. Address: Bidekurtzeta 6, 20500 Arrasate Gipuzkoa Spain Product Name: Rebadge FCC ID: 2BKZ6-REBADGE2 Model(s): Rebadge 2 2.911(d)(7) USA Designated Agent for Service of Process We, [JMA ALEJANDRO ALTUNA, S.L.U. ] (“the applicant”) designate [THREE STONES MEDIA LLC] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We Acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We Acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Company name: THREE STONES MEDIA LLC Address: 1200 Broadway St. APT 329, Los Angeles, CA90015 FRN: 0033401761 Contact Name: Sijie Zhang Telephone No: +1 267 909 3692 Email: [email protected] Applicant Company name: JMA ALEJANDRO ALTUNA, S.L.U. Address: Bidekurtzeta 6, 20500 Arrasate Gipuzkoa Spain FRN: 0035934710 FCC Grantee Code: 2BKZ6 Contact Name: Ivy Wang Telephone No: +34 943793000 Email: [email protected] Signature: Title: Signature: Title: Sales Date: 2024-09-25 Date: 2024-09-25 S俨沪� JMA ALEJANDRO ALTUNA, S.L.U. 2.911 (d)(7)USA Agent v1.2 NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threat s-to-the-communications-supply-chain-through-the

JMA ALEJANDRO ALTUNA, S.L.U. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2024-09-25 Subject; Request for Long Term Confidentiality FCC ID: 2BKZ6-REBADGE2 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Ivy Wang Title: sales

Letter of Authorization Company: JMA ALEJANDRO ALTUNA, S.L.U. Address: Bidekurtzeta 6, 20500 Arrasate Gipuzkoa Spain Product Name: Rebadge Model Number: Rebadge 2 FCC Identifier: 2BKZ6-REBADGE2 We authorize MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the above named equipment. Any individual within MiCOM Labs is authorized to act on our behalf and take action on the application. We declare that MiCOM Labs Inc, 575 Boulder Court, Pleasanton, California 94566, USA, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Name: Ivy Wang Date: 2024-09-25 Title: sales

Model:Rebadge2 External Model:Rebadge2

Label&Location Rebadge Model: Rebadge 2 FCC ID: 2BKZ6-REBADGE2

Model:Rebadge2 Internal Model:Rebadge2 Model:Rebadge2 Thisantennaisdisconnectedfromthe RFchipanddoesnottransmitsignal Model:Rebadge2

TotalorpartialreproductionofthisdocumentwithoutpermissionoftheLaboratoryisnotallowed.Page 1 of 7 BTFTestingLab(Shenzhen)Co.,Ltd. F101,201and301,Building1,Block2,TantouIndustrialPark,TantouCommunity,SonggangStreet,Bao'anDistrict,Shenzhen,China RFExposureReport For ApplicantName:JMAALEJANDROALTUNA,S.L.U. Address:Bidekurtzeta6,20500ArrasateGipuzkoaSpain EUTName:Rebadge BrandName: "REBADGE" EU:014426274 UK:014426274 AU:1928791 NZ:1093580 ModelNumber:Rebadge2 IssuedBy CompanyName:BTFTestingLab(Shenzhen)Co.,Ltd. Address: F101,201and301,Building1,Block2,TantouIndustrialPark, TantouCommunity,SonggangStreet,Bao'anDistrict,Shenzhen, China ReportNumber:BTF240903R00302 TestStandards:47CFRPart2SubpartJSection2.1093 FCCID:2BKZ6-REBADGE2 TestConclusion:Pass TestDate:2024-09-03to2024-09-18 DateofIssue:2024-09-18 Testby: Ssxx.guo/Tester PreparedBy: AriaZhang/ProjectEngineer Date:2024-09-18 ApprovedBy: Ryan.CJ/EMCManager Date:2024-09-18 Note:Allthetestresultsinthisreportonlyrelatedtothetestingsamples.Whichcanbeduplicatedcompletelyforthelegalusewithapprovalof applicant;itshallnotbereproducedexceptinfullwithoutthewrittenapprovalofBTFTestingLab(Shenzhen)Co.,Ltd.,Alltheobjectionsshouldbe raisedwithinthirtydaysfromthedateofissue.Tovalidatethereport,youcancontactus. TestReportNumber:BTF240903R00302 TotalorpartialreproductionofthisdocumentwithoutpermissionoftheLaboratoryisnotallowed.Page 2 of 7 BTFTestingLab(Shenzhen)Co.,Ltd. F101,201and301,Building1,Block2,TantouIndustrialPark,TantouCommunity,SonggangStreet,Bao'anDistrict,Shenzhen,China RevisionHistory VersionIssueDateRevisionsContent R_V02024-09-18Original Note:Oncetherevisionhasbeenmade,thenpreviousversionsreportsareinvalid. TestReportNumber:BTF240903R00302 TotalorpartialreproductionofthisdocumentwithoutpermissionoftheLaboratoryisnotallowed.Page 3 of 7 BTFTestingLab(Shenzhen)Co.,Ltd. F101,201and301,Building1,Block2,TantouIndustrialPark,TantouCommunity,SonggangStreet,Bao'anDistrict,Shenzhen,China TableofContents 1.Introduction.............................................................................................................................................................................................4 1.1IdentificationofTestingLaboratory..................................................................................................................................4 1.2IdentificationoftheResponsibleTestingLocation......................................................................................................4 1.3LaboratoryCondition............................................................................................................................................................4 1.4Announcement........................................................................................................................................................................4 2.ProductInformation...............................................................................................................................................................................5 2.1ApplicationInformation........................................................................................................................................................5 2.2ManufacturerInformation.....................................................................................................................................................5 2.3FactoryInformation...............................................................................................................................................................5 2.4GeneralDescriptionofEquipmentunderTest(EUT)...................................................................................................5 3.TestRequirement..................................................................................................................................................................................6 3.1AssessmentResult................................................................................................................................................................6 TestReportNumber:BTF240903R00302 TotalorpartialreproductionofthisdocumentwithoutpermissionoftheLaboratoryisnotallowed.Page 4 of 7 BTFTestingLab(Shenzhen)Co.,Ltd. F101,201and301,Building1,Block2,TantouIndustrialPark,TantouCommunity,SonggangStreet,Bao'anDistrict,Shenzhen,China 1.Introduction 1.1IdentificationofTestingLaboratory CompanyName:BTFTestingLab(Shenzhen)Co.,Ltd. Address: F101,201and301,Building1,Block2,TantouIndustrialPark,Tantou Community,SonggangStreet,Bao'anDistrict,Shenzhen,China PhoneNumber:+86-0755-23146130 FaxNumber:+86-0755-23146130 1.2IdentificationoftheResponsibleTestingLocation TestLocation:BTFTestingLab(Shenzhen)Co.,Ltd. Address: F101,201and301,Building1,Block2,TantouIndustrialPark,Tantou Community,SonggangStreet,Bao'anDistrict,Shenzhen,China Description: Allmeasurementfacilitiesusedtocollectthemeasurementdataarelocated atF101,201and301,Building1,Block2,TantouIndustrialPark,Tantou Community,SonggangStreet,Bao'anDistrict,Shenzhen,China FCCRegistrationNumber:518915 DesignationNumber:CN1330 1.3LaboratoryCondition AmbientTemperature:20°Cto25°C AmbientRelativeHumidity:45%to55% AmbientPressure:100kPato102kPa 1.4Announcement (1)Thetestreportreferencetothereporttemplateversionv0. (2)Thetestreportisinvalidifnotmarkedwiththesignaturesofthepersonsresponsibleforpreparing, reviewingandapprovingthetestreport. (3)Thetestreportisinvalidifthereisanyevidenceand/orfalsification. (4)ThisdocumentmaynotbealteredorrevisedinanywayunlessdonesobyBTFandallrevisionsareduly notedintherevisionssection. (5)Contentofthetestreport,inpartorinfull,cannotbeusedforpublicityand/orpromotionalpurposeswithout priorwrittenapprovalfromthelaboratory. (6)Thelaboratoryisonlyresponsibleforthedatareleasedbythelaboratory,exceptforthepartprovidedbythe applicant. TestReportNumber:BTF240903R00302 TotalorpartialreproductionofthisdocumentwithoutpermissionoftheLaboratoryisnotallo…

Text truncated - open the document above for the full version.

$QWH QQDGHVFULEH $QWHQQDGHVFULEH $QWHQQDSODWH0RQRSORHDQWHQQD 0DNH QDPHPRGHOQDPH) $QWHQ QDJDLQG%L )UHTX HQF\UDQJH*+=*+= &RQQH FWRUW\SHGLUHFW ([W HUQDOYLHZGUDZLQJ 3LFWXUHRIDQWHQQD $QWHQQD5DGLDWLRQ3DWWHUQ 5DGLDWLRQSDWWHUQ#*+= 7RWDO$YHUDJH*DLQGEL         3KL *DLQ         5DGLDWLRQSDWWHUQ#*+= 7RWDO$YHUDJH*DLQGEL  3KL *DLQ  5DGLDWLRQSDWWHUQ#*+= 7RWDO$YHUDJH*DLQGEL  3KL *DLQ 

TotalorpartialreproductionofthisdocumentwithoutpermissionoftheLaboratoryisnotallowed. Page1of59 BTFTestingLab(Shenzhen)Co.,Ltd. F101,201and301,Building1,Block2,TantouIndustrialPark,TantouCommunity,SonggangStreet,Bao'anDistrict,Shenzhen,China RFTestReport For ApplicantName:JMAALEJANDROALTUNA,S.L.U. Address:Bidekurtzeta6,20500ArrasateGipuzkoaSpain EUTName:Rebadge BrandName: "REBADGE" EU:014426274 UK:014426274 AU:1928791 NZ:1093580 ModelNumber:Rebadge2 IssuedBy CompanyName:BTFTestingLab(Shenzhen)Co.,Ltd. Address: F101,201and301,Building1,Block2,TantouIndustrialPark, TantouCommunity,SonggangStreet,Bao'anDistrict,Shenzhen, China ReportNumber:BTF240903R00301 TestStandards:47CFRPart15.247 TestConclusion:Pass FCCID:2BKZ6-REBADGE2 TestDate:2024-09-03to2024-09-18 DateofIssue:2024-09-18 Testby: Ssxx.guo/Tester PreparedBy: AriaZhang/ProjectEngineer Date:2024-09-18 ApprovedBy: Ryan.CJ/EMCManager Date:2024-09-18 Note:Allthetestresultsinthisreportonlyrelatedtothetestingsamples.Whichcanbeduplicatedcompletelyforthelegalusewithapprovalof applicant;itshallnotbereproducedexceptinfullwithoutthewrittenapprovalofBTFTestingLab(Shenzhen)Co.,Ltd.,Alltheobjectionsshouldbe raisedwithinthirtydaysfromthedateofissue.Tovalidatethereport,youcancontactus. TestReportNumber:BTF240903R00301 TotalorpartialreproductionofthisdocumentwithoutpermissionoftheLaboratoryisnotallowed. Page2of59 BTFTestingLab(Shenzhen)Co.,Ltd. F101,201and301,Building1,Block2,TantouIndustrialPark,TantouCommunity,SonggangStreet,Bao'anDistrict,Shenzhen,China RevisionHistory VersionIssueDateRevisionsContent R_V02024-09-18Original Note:Oncetherevisionhasbeenmade,thenpreviousversionsreportsareinvalid. TestReportNumber:BTF240903R00301 TotalorpartialreproductionofthisdocumentwithoutpermissionoftheLaboratoryisnotallowed. Page3of59 BTFTestingLab(Shenzhen)Co.,Ltd. F101,201and301,Building1,Block2,TantouIndustrialPark,TantouCommunity,SonggangStreet,Bao'anDistrict,Shenzhen,China TableofContents 1INTRODUCTION.................................................................................................................................................5 1.1IdentificationofTestingLaboratory...................................................................................................5 1.2IdentificationoftheResponsibleTestingLocation..........................................................................5 1.3Announcement......................................................................................................................................5 2PRODUCTINFORMATION.................................................................................................................................6 2.1ApplicationInformation.......................................................................................................................6 2.2ManufacturerInformation....................................................................................................................6 2.3FactoryInformation..............................................................................................................................6 2.4GeneralDescriptionofEquipmentunderTest(EUT).......................................................................6 2.5TechnicalInformation..........................................................................................................................6 3SUMMARYOFTESTRESULTS.........................................................................................................................7 3.1TestStandards......................................................................................................................................7 3.2UncertaintyofTest...............................................................................................................................7 3.3SummaryofTestResult.......................................................................................................................7 4TESTCONFIGURATION.....................................................................................................................................8 4.1TestEquipmentList.............................................................................................................................8 4.2TestAuxiliaryEquipment...................................................................................................................10 4.3TestModes..........................................................................................................................................10 5EVALUATIONRESULTS(EVALUATION)........................................................................................................11 5.1Antennarequirement..........................................................................................................................11 5.1.1Conclusion:..............................................................................................................................11 6RADIOSPECTRUMMATTERTESTRESULTS(RF)......................................................................................12 6.1ConductedEmissionatACpowerline............................................................................................12 6.1.1E.U.T.Operation:.....................................................................................................................12 6.1.2TestSetupDiagram:................................................................................................................12 6.1.3TestData:................................................................................................................................13 6.2OccupiedBandwidth..........................................................................................................................15 6.2.1E.U.T.Operation:.....................................................................................................................15 6.2.2TestSetupDiagram:...........................…

Text truncated - open the document above for the full version.

Model: Rebadge 2 Conducted Emission at AC power line Emissions in frequency bands (below 1GHz) Model: Rebadge 2 Band edge emissions (Radiated) Emissions in frequency bands (above 1GHz)