2BO9717PROSmartphone

Federal Communication Commission Interference Statement FCC ID: 2BO9717PRO This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Radiation Exposure Statement: This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. Tests for SAR are conducted using standard operating positions (10mm) accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. The use of holsters and similar accessories should not contain metallic components in its assembly, the use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.

Rev 1/26/2023 NOVISOLUTIONS CIA LTDA Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2026-08-28 FCC ID: 2BO9717PRO Ref. #1: Attestation Statements Part 2.911(d)(5)(i) Filing NOVISOLUTIONS CIA LTDA certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. NOVISOLUTIONS CIA LTDA certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Ref. #2: Attestation Statements Part 2.911(d)(5)(ii) Filing NOVISOLUTIONS CIA LTDA certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Applicant: NOVISOLUTIONS CIA LTDA Address: Ponceano N73 y Mariano Paredes QUITO ECUADOR Contact Person: MARIA CRUZ Tel.: 593968584819 Email: [email protected] Sincerely, Signature:

Attestation Statements Date: 2026-08-28 TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA RE: Attestation Statements Part 2.911(d)(7) request for(FCC ID: 2BO9717PRO) NOVISOLUTIONS CIA LTDA, the undersigned, hereby authorize HOPEK CORPORATION INC to act as our designated agent for service of process, NOVISOLUTIONS CIA LTDA accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. HOPEK CORPORATION INC accepts the responsibility to act as designated agent for service of process. Applicant Information： Company name: NOVISOLUTIONS CIA LTDA Contact Name: MARIA CRUZ Address: Ponceano N73 y Mariano Paredes QUITO ECUADOR Telephone No: 593968584819 Email: [email protected] FRN: 0037016730 Signature: MARIA CRUZ Agent Information: Company Name: HOPEK CORPORATION INC Address: 16755 Coyote Bush Dr Unit 84, San Diego, CA 92127 United States FRN: 0034562900 Contact Name: Yangyang Xu Telephone No: 561-875-9826 Email: [email protected] Signature: Yangyang Xu

NOVISOLUTIONS CIA LTDA Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: August 28, 2026 Subject; Request for Confidentiality FCC ID: 2BO9717PRO To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: MARIA CRUZ Title: PURCHASE MANAGER

Effective Date: April 2, 2020 QSF 7.6.4-8 – Agent Authorization Letter Template Page 1 of 1 Revision Date: Revision: 0 NOVISOLUTIONS CIA LTDA Date：2026-08-28 Product Model Number: 17 PRO FCC ID：2BO9717PRO To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following: • Testing • Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. Signature: By: MARIA CRUZ Contact Listed on FCC Wesbite Title: PURCHASE MANAGER Email: [email protected] On behalf of: NOVISOLUTIONS CIA LTDA

Page 1 of 5 Report No.: LGT26G035 Appendix - External Photographs of EUT Constructional Details Photo 1 Photo 2 Page 2 of 5 Report No.: LGT26G035 Appendix - External Photographs of EUT Constructional Details Photo 3 Photo 4 Page 3 of 5 Report No.: LGT26G035 Appendix - External Photographs of EUT Constructional Details Photo 5 Photo 6 Page 4 of 5 Report No.: LGT26G035 Appendix - External Photographs of EUT Constructional Details Photo 7 Photo 8 Page 5 of 5 Report No.: LGT26G035 Appendix - External Photographs of EUT Constructional Details Photo 9 Photo 10

Label This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Page 1 of 8 Report No.: LGT26G035 Appendix - Internal Photographs of EUT Constructional Details Photo 1 Photo 2 MAIN ANT DIV ANT GPS/Wi-Fi/BT ANT Page 2 of 8 Report No.: LGT26G035 Appendix - Internal Photographs of EUT Constructional Details Photo 3 Photo 4 Page 3 of 8 Report No.: LGT26G035 Appendix - Internal Photographs of EUT Constructional Details Photo 5 Photo 6 Page 4 of 8 Report No.: LGT26G035 Appendix - Internal Photographs of EUT Constructional Details Photo 7 Photo 8 Page 5 of 8 Report No.: LGT26G035 Appendix - Internal Photographs of EUT Constructional Details Photo 9 Photo 10 Page 6 of 8 Report No.: LGT26G035 Appendix - Internal Photographs of EUT Constructional Details Photo 11 Photo 12 Page 7 of 8 Report No.: LGT26G035 Appendix - Internal Photographs of EUT Constructional Details Photo 13 Photo 14 Page 8 of 8 Report No.: LGT26G035 Appendix - Internal Photographs of EUT Constructional Details Photo 15 Photo 16

Page: 1/10 Ref : ACR.37.13.26.PAR.B Cancel and replace the report ACR.37.13.26.PAR.A SHENZHEN LGT TEST SERVICE CO., LTD. ROOM 205, BUILDING 13,ZONE B, ZHENXIONGINDUSTRIAL PARK, NO.177, RENMIN WEST ROAD,JINSHA, KENGZI STREET, PINGSHAN DISTRICT,SHENZHEN, GUANGDONG, CHINA MVG COMOSAR DOSIMETRIC E-FIELD PROBE SERIAL NO.: 0326-EPGO-431 Calibrated at MVG 13 Rue du Zephyr 91140 Villejust - FRANCE Calibration date: 2026/01/22 Scope available on :https://a2la.org/ Summary: This document presents the method and results from an accredited COMOSAR Dosimetric E-Field Probe calibration performed at MVG, using the CALIPROBE test bench, for use with a MVG COMOSAR system only. The test results covered by accreditation are traceable to the International System of Units (SI). COMOSAR E-Field Probe Calibration Report Docusign Envelope ID: 441A23A1-88DE-4D98-BD64-561319DF94DB COMOSAR E-FIELD PROBE CALIBRATION REPORT Ref: ACR.37.13.26.PAR.B Page: 2/10 Template_ACR.DDD.N.YY.MVGB.ISSUE_COMOSAR Probe vN This document shall not be reproduced, except in full or in part, without the written approval of MVG. The information contained herein is to be used only for the purpose for which it is submitted and is not to be released in whole or part without written approval of MVG. Name Function Date Signature Prepared by : Pedro Ruiz Technical Manager 2/6/2026 Checked & approved by: Pedro Ruiz Technical Manager 2/6/2026 Authorized by: Christophe Barrot Quality Manager Customer Name Distribution : SHENZHEN LGT TEST SERVICE CO., LTD Issue Name Date Modifications A Pedro Ruiz 2/6/2026 Initial release B Pedro Ruiz 04/10/2026 Update customer address Docusign Envelope ID: 441A23A1-88DE-4D98-BD64-561319DF94DB 2026 April 13 COMOSAR E-FIELD PROBE CALIBRATION REPORT Ref: ACR.37.13.26.PAR.B Page: 3/10 Template_ACR.DDD.N.YY.MVGB.ISSUE_COMOSAR Probe vN This document shall not be reproduced, except in full or in part, without the written approval of MVG. The information contained herein is to be used only for the purpose for which it is submitted and is not to be released in whole or part without written approval of MVG. TABLE OF CONTENTS 1 Device Under Test ..................................................................................................... 4 2 Product Description ................................................................................................... 4 2.1 General Information _______________________________________________________ 4 3 Measurement Method ................................................................................................ 4 3.1 Sensitivity _______________________________________________________________ 4 3.2 Linearity ________________________________________________________________ 4 3.3 Isotropy _________________________________________________________________ 5 3.4 Boundary Effect __________________________________________________________ 5 3.5 Probe Modulation Response _________________________________________________ 5 4 Measurement Uncertainty .......................................................................................... 6 5 Calibration Results ..................................................................................................... 6 5.1 Calibration in air __________________________________________________________ 6 5.2 Calibration in liquid _______________________________________________________ 7 6 Verification Results ................................................................................................... 8 7 List of Equipment ...................................................................................................... 9 Docusign Envelope ID: 441A23A1-88DE-4D98-BD64-561319DF94DB COMOSAR E-FIELD PROBE CALIBRATION REPORT Ref: ACR.37.13.26.PAR.B Page: 4/10 Template_ACR.DDD.N.YY.MVGB.ISSUE_COMOSAR Probe vN This document shall not be reproduced, except in full or in part, without the written approval of MVG. The information contained herein is to be used only for the purpose for which it is submitted and is not to be released in whole or part without written approval of MVG. 1 DEVICE UNDER TEST Device Under Test Device Type COMOSAR DOSIMETRIC E FIELD PROBE Manufacturer MVG Model SSE2 Serial Number 0326-EPGO-431 Product Condition (new / used) New Frequency Range of Probe 0.15 GHz-7.5GHz Resistance of Three Dipoles at Connector Dipole 1: R1=0.234 M Dipole 2: R2=0.234 M Dipole 3: R3=0.214 M 2 PRODUCT DESCRIPTION 2.1 GENERAL INFORMATION MVG’s COMOSAR E field Probes are built in accordance to the IEC/IEEE 62209-1528 and FCC KDB865664 D01 standards. Figure 1 – MVG COMOSAR Dosimetric E field Probe Probe Length 330 mm Length of Individual Dipoles 2 mm Maximum external diameter 8 mm Probe Tip External Diameter 2.5 mm Distance between dipoles / probe extremity 1 mm 3 MEASUREMENT METHOD The IEC/IEEE 62209-1528 and FCC KDB865664 D01 standards provide recommended practices for the probe calibrations, including the performance characteristics of interest and methods by which to assess their effect. All calibrations / measurements performed meet the fore-mentioned standards. 3.1 SENSITIVITY The sensitivity factors of the three dipoles were determined using a two step calibration method (air and tissue simulating liquid) using waveguides as outlined in the standards for frequency range 600- 7500MHz and using the calorimeter cell method (transfer method) as outlined in the standards for frequency 150-450 MHz. 3.2 LINEARITY The evaluation of the linearity was done in free space using the waveguide, performing a power sweep to cover the SAR range 0.01W/kg to 100W/kg. Docusign Envelope ID: 441A23A1-88DE-4D98-BD64-561319DF94DB COMOSAR E-FIELD PROBE CALIBRATION REPORT Ref: ACR.37.13.26.PAR.B Page: 5/10 Template_ACR.DDD.N.YY.MVGB.ISSUE_COMOSAR Probe vN This document shall not be reproduced, except in full or in part, without the written approval of MVG. The information contained herein is to be used only for the purpose for which it is submitted and is…

Text truncated - open the document above for the full version.

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Page 1 of 74 SAR TEST REPORT Product Name: Smartphone Model Number: 17 PRO FCC ID: 2BO9717PRO Issued For : NOVISOLUTIONS CIA LTDA Ponceano N73 y Mariano Paredes QUITO ECUADOR Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT26G035HA01 Sample Received Date: Jul. 24, 2026 Date of Test Jul. 24, 2026 ~ Aug. 11, 2026 Date of Issue Aug. 11, 2026 Max. SAR (1g) Head: 0.556 W/kg Body: 1.048 W/kg Reprot No.: LGT26G035HA01 Page 2 of 74 Table of Contents 1. General Information 5 1.1 EUT Description 5 1.2 Test Environment 7 1.3 Test Factory 7 2. Test Standards and Limits 8 3. SAR Measurement System 9 3.1 Definition of Specific Absorption Rate (SAR) 9 3.2 SAR System 9 4. Tissue Simulating Liquids 12 4.1 Simulating Liquids Parameter Check 12 5. SAR System Validation 14 5.1 Validation System 14 5.2 Validation Result 15 6. SAR Evaluation Procedures 16 7. EUT Antenna Location Sketch 17 7.1 SAR test exclusion consider table 18 8. EUT Test Position 21 8.1 Define Two Imaginary Lines on the Handset 21 8.2 Hotspot mode exposure position condition 22 9. Uncertainty 23 9.1 Measurement Uncertainty 23 9.2 System validation Uncertainty 24 10. Conducted Power Measurement 25 10.1 Test Result 25 11. EUT and Test Setup Photo 35 11.1 EUT Photos 35 11.2 Setup Photos 38 12. SAR Result Summary 44 12.1 Head SAR 44 12.2 Body-worn and Hotspot SAR 46 12.3 Repeated SAR 48 12.4 Repeated SAR measurement 48 12.5 Simultaneous Multi-band Transmission Evaluation 49 13. Equipment List 51 Appendix A. System Validation Plots 52 Reprot No.: LGT26G035HA01 Page 3 of 74 Appendix B. SAR Test Plots 60 Appendix C. Probe Calibration and Dipole Calibration Report 74 Revision History Rev. Issue Date Contents 00 Aug. 11, 2026 Initial Issue Reprot No.: LGT26G035HA01 Page 4 of 74 TEST REPORT CERTIFICATION Applicant NOVISOLUTIONS CIA LTDA Address Ponceano N73 y Mariano Paredes QUITO ECUADOR Manufacture NOVISOLUTIONS CIA LTDA Address Ponceano N73 y Mariano Paredes QUITO ECUADOR Product Name Smartphone Trademark ENV Model Number 17 PRO Sample number LGT2607098-5 APPLICABLE STANDARDS STANDARD TEST RESULTS ANSI/IEEE Std. C95.1-2019 FCC 47 CFR Part 2 (2.1093) IEEE 1528: 2013 PASS Prepared by: Approved by: Deng Deng Engineer Vita Li Manager Reprot No.: LGT26G035HA01 Page 5 of 74 1. General Information Environmental evaluation measurements of specific absorption rate (SAR) distributions in emulated human head and body tissues exposed to radio frequency (RF) radiation from wireless portable devices for compliance with the rules and regulations of the U.S. Federal Communications Commission (FCC). 1.1 EUT Description Product Name Smartphone Test Model Number 17 PRO Series Number N/A Model Difference here are two memory options for one model: the main test model has 4GB RAM and 128GB storage, while the other model is the same but has 4GB RAM and 64GB storage. Device Category Portable Product stage Production unit RF Exposure Environment General Population / Uncontrolled Hardware Version N/A Software Version N/A Frequency Range GSM GSM 850 824~849 MHz PCS 1900 1850~1910 MHz WCDMA Band II 1850~1910 MHz Band V 824~849 MHz LTE Band 2 1850~1910MHz Band 4 1710~1755MHz WLAN 2412~2462 MHz Bluetooth 2402~2480 MHz Max. Reported SAR(1g): (Limit:1.6W/kg) Head:0mm Body:10mm Mode Head (W/ kg) Body Worn and Hotspot (W/ kg) GSM 850 0.556 0.75 PCS 1900 0.231 0.55 WCDMA Band II 0.154 0.709 WCDMA Band V 0.437 0.715 LTE Band 2 0.468 0.521 LTE Band 4 0.531 1.048 2.4G WLAN 0.493 0.159 Bluetooth Note 0.166 0.166 1-g Sum SAR 1.049 1.214 Test distance 0mm 10mm Battery Capacity: 5000mAh/19.25Wh Rated Voltage: 3.85V Operating Mode GSM: GSM Voice; GPRS/EGPRS Class 12 WCDMA: RMC, HSDPA, HSUPA Release 6 LTE: QPSK, 16QAM 2.4G WLAN: 802.11b(DSSS): CCK, DQPSK, DBPSK 802.11g(OFDM): BPSK, QPSK,16-QAM,64-QAM 802.11n(OFDM): BPSK, QPSK,16-QAM,64-QAM Reprot No.: LGT26G035HA01 Page 6 of 74 Bluetooth: GFSK +π/4DQPSK+8DPSK BLE: GFSK Antenna Specification GSM/WCDMA/LTE: PIFA Antenna Bluetooth: PIFA Antenna WLAN: PIFA Antenna Operating Mode Maximum continuous output SIM Card SIM 1 and SIM 2 is a chipset unit and tested as single chipset, SIM 1 is used to tested. Hotspot Mode Support DTM Mode Not Support Note: 1. The BT value was Estimated. 2. The EUT battery must be fully charged and checked periodically during the test to ascertain uniform power. 3. After pre-scan two SIM cards power, we found test result of the SIM1 was the worse, so we chose SIM1 card to perform all tests. Reprot No.: LGT26G035HA01 Page 7 of 74 1.2 Test Environment Ambient conditions in the SAR laboratory: Items Required Temperature (°C) 18-25 Humidity (%RH) 30-70 1.3 Test Factory Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate FCC Registration No.: 746540 CAB ID: CN0136 Reprot No.: LGT26G035HA01 Page 8 of 74 2. Test Standards and Limits No. Identity Document Title 1 47 CFR Part 2 Frequency Allocations and Radio Treaty Matters; General Rules and Regulations 2 ANSI/IEEE Std. C95.1-2019 IEEE Standard for Safety Levels with Respect to Human Exposure to Electric, Magnetic, and Electromagnetic Fields, 0 Hz to 300 GHz 3 IEEE Std. 1528-2013 Recommended Practice for Determining the Peak Spatial- Average Speci…

Text truncated - open the document above for the full version.

Antenna Specification Laboratory test environment and equipment Test ItemTest Equipment S11、S12 、VSWR 、LOSS E5071B、E5062A Efficiency、Gain 3D Radiation Pattern Satimo SG16、GP7*4*3、E5071B TRP、TIS Satimo SG16、GP7*4*3、8960 、 CMW500、MT8820C、E4438C、 Project Commissioning Introduction Complete machine type 4G intelligent machine Frequency band information Antenna form Antenna type and frequency band information Main antenna GSM850/900/1800/1900 WCDMA；B1/2/4/5/8 FDD: B1/2/3/4/5/7/12/17/28/66/38 PIFA Secondary antenna WIFI+BT+GPSPIFA diversity antenna 700M-2710MHZPIFA Antenna type PIFA Antenna antenna switch matching circuit and logic Upper Antenna TRXDRX 2G:// 3G:/WCDMA-B1，5，8 4G:/LTE-B1,3,5,8 Lower Antenna (Tuning switch) TRXDRX RF1 GSM900,DCS1800,PCS1900+WCDMA-B1/2/4/8+LTE- B1,2/3/4/7/66/38 / RF2GSM850+WCDMA-B5+LTE-B5/ RF3LTE12/17/28/ RF4NA/ Lower antenna matching R121 0R R122 3.6NH R124 9.1NH C900 0R Three-in-one antenna matching WIFI antenna size length: 19mm width:5.5mm S11 figure Main antenna Diversity antenna Three-in-one antenna Apple Chart/Efficiency Freqency (MHz) Gain(dBi) Efficiency (dB) Efficiency (%) 700-3.14-7.0319.84 710-2.94-6.9820.04 720-3.26-6.8920.47 730-3.59-6.9820.03 740-3.21-6.4822.47 750-4.1-7.2518.83 760-2.94-6.9820.04 770-4.64-7.7816.67 780-3.91-7.0819.61 790-3.77-7.1219.4 Apple Chart/Efficiency Freqency(MHz)Gain(dBi)Efficiency(dB)Efficiency(%) 880-3.18-6.9320.26 890-3.11-6.7821 900-2.91-6.8120.84 910-2.84-6.8720.55 920-2.95-7.2618.8 930-3.26-7.5817.47 940-3.18-7.8616.36 950-3.18-8.2315.03 960-3.58-8.8113.17 Freqency(MHz)Gain(dBi)Efficiency(dB)Efficiency(%) 800-3.18-7.3218.55 810-2.95-7.0419.79 820-3.02-6.8920.47 830-3.1-6.8720.54 840-2.96-6.6621.56 850-3.02-6.920.39 860-3.22-7.1719.18 870-3.46-7.3518.39 880-3.71-7.5717.49 890-4.16-815.84 900-4.83-8.4714.22 Apple Chart/Efficiency Freqency(MHz)Gain(dBi)Efficiency(dB)Efficiency(%) 1700-4.09-9.5511.08 1720-3.61-9.0812.36 1740-3.44-8.7513.34 1760-3.33-8.514.13 1780-3.2-8.3214.72 1800-2.44-815.86 1820-1.8-7.5317.67 1840-1.57-7.2218.97 1860-1.54-7.0519.72 1880-1.77-6.9320.26 1900-1.94-6.8820.53 1920-2.24-6.8720.58 1940-2.63-6.9520.17 1960-3.14-7.0619.66 1980-3.64-6.920.39 2000-3.69-6.9120.36 2020-3.61-6.9320.29 2040-3.57-6.8720.54 2060-3.53-7.0119.89 2080-3.4-719.97 2100-3.23-6.9520.2 2120-2.88-719.96 2140-2.77-6.9220.3 2160-2.79-6.9320.26 2180-2.78-6.7920.93 Apple Chart/Efficiency 2200-1.85-5.5427.91 2220-1.97-5.4728.35 2240-2.04-5.3729.06 2260-2.13-5.4428.55 2280-2.5-5.6327.34 2300-2.98-5.9825.26 2320-3.07-6.3423.22 2340-2.75-6.7920.95 2360-2.41-7.119.48 2380-2.08-7.1419.32 2400-1.66-719.96 2420-1.48-6.6921.45 2440-1.01-6.223.99 2460-0.66-5.7126.84 2480-0.42-5.1130.82 2500-0.13-4.6334.45 2520-0.22-4.3237.01 2540-0.17-4.2537.57 2560-0.03-4.2737.41 25800.07-4.3336.93 2600-0.08-4.5435.15 2620-0.1-4.7733.34 2640-0.13-4.9432.07 2660-0.35-5.1830.31 2680-0.57-5.4828.29 2700-0.63-5.6727.08 Apple Chart/Efficiency WIFI/BT-2.4G Freqency(MHz)Gain(dBi)Efficiency(dB)Efficiency(%) 24001.79-5.2230.08 24101.76-5.0831.06 24201.86-4.9132.29 24301.92-4.8432.81 24401.96-4.7833.26 24501.93-4.7933.2 24601.92-4.8332.92 24702.01-4.833.11 24802.04-4.7933.22 24902.11-4.7833.25 25002.19-4.7933.17 Freqency(MHz)Gain(dBi)Efficiency(dB)Efficiency(%) 15001.3-4.2937.2 15101.57-3.9740.1 15201.34-3.9440.36 15301.24-3.8541.23 15401.52-3.5244.43 15501.76-3.3346.5 15601.88-3.2447.42 15702.14-3.0849.24 15802.22-3.0249.85 15902.07-3.1748.18 16002.04-3.2347.58 Apple Chart/Efficiency Freqency(MHz)Gain(dBi)Efficiency(dB)Efficiency(%) 51001.31-6.0924.61 51201.33-6.0624.78 51401.27-6.323.46 51601.4-6.1424.34 51801.49-6.0824.68 52001.29-6.1924.03 52201.65-6.0524.84 52401.78-5.8925.73 52601.56-6.1424.35 52801.69-5.9525.38 53001.66-5.925.69 53201.77-5.7726.48 53401.27-5.9325.55 53601.46-5.9125.66 53801.45-6.0524.85 54001.95-5.925.73 54202.23-5.8625.95 54402.32-5.7926.39 54602.36-5.8326.13 54802.53-5.9925.18 55202.4-6.1824.08 55402.55-6.2523.72 55602.58-6.4222.78 55802.19-6.6321.74 56001.95-6.820.91 56202.41-6.7721.02 56402.29-6.9120.35 56602.16-7.0519.73 56802.13-7.1319.38 57001.83-7.2518.83 57201.82-7.4717.9 57402-7.3818.3 57601.85-7.3918.23 57801.54-7.816.59 58001.41-7.9216.15 58201.44-7.9216.14 58401.45-8.2714.9 Apple Chart/Efficiency Apple Chart/Efficiency Apple Chart/Efficiency Apple Chart/Efficiency Apple Chart/Efficiency Apple Chart/Efficiency Environmental treatment Original environmental treatment of other trial production machines Contact Information： RF ： Jiangong Tel ：15014104367 Email ：[email protected] Address ： 2nd Floor, Yulong Office Building, Longcheng Industrial Zone, 440 Longguan Avenue, Longhua District Contact Information THE END Thank you for your valuable comments!

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Page 1 of 52 RF TEST REPORT Product Name: Smartphone Model Number: 17 PRO FCC ID: 2BO9717PRO Issued For : NOVISOLUTIONS CIA LTDA Ponceano N73 y Mariano Paredes QUITO ECUADOR Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT26G035RF02 Sample Received Date: Jul. 11, 2026 Date of Test: Jul. 11, 2026 ~ Jul. 29, 2026 Date of Issue: Jul. 29, 2026 Report No.: LGT26G035RF02 Page 2 of 52 TEST REPORT CERTIFICATION Applicant: NOVISOLUTIONS CIA LTDA Address: Ponceano N73 y Mariano Paredes QUITO ECUADOR Manufacturer: NOVISOLUTIONS CIA LTDA Address: Ponceano N73 y Mariano Paredes QUITO ECUADOR Product Name: Smartphone Trademark: ENV Model Number: 17 PRO Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC Part 15.247, Subpart C ANSI C63.10-2020 + Cor. 1-2023+C63.10a-2024 + Errata to C63.10a-2024 PASS Prepared by: Approved by: Chris Chen Vita Li Engineer Technical Director Report No.: LGT26G035RF02 Page 3 of 52 Table of Contents Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST LABORATORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 9 2.3 TEST SOFTWARE AND POWER LEVEL 9 2.4 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 10 2.5 EQUIPMENTS LIST 11 3. EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.2 TEST PROCEDURE 14 3.3 TEST SETUP 14 3.4 EUT OPERATING CONDITIONS 14 3.5 TEST RESULTS 15 4. RADIATED EMISSION MEASUREMENT 17 4.1 RADIATED EMISSION LIMITS 17 4.2 TEST PROCEDURE 19 4.3 TEST SETUP 19 4.4 EUT OPERATING CONDITIONS 20 4.5 FIELD STRENGTH CALCULATION 20 4.6 TEST RESULTS (BAND EDGE REQUIREMENTS) 25 5. CONDUCTED SPURIOUS & BAND EDGE EMISSION 26 5.1 LIMIT 26 5.2 TEST PROCEDURE 26 5.3 TEST SETUP 26 5.4 EUT OPERATION CONDITIONS 26 5.5 TEST RESULTS 26 6. POWER SPECTRAL DENSITY TEST 27 6.1 LIMIT 27 6.2 TEST PROCEDURE 27 6.3 TEST SETUP 27 6.4 EUT OPERATION CONDITIONS 27 Report No.: LGT26G035RF02 Page 4 of 52 6.5 TEST RESULTS 27 7. BANDWIDTH TEST 28 7.1 LIMIT 28 7.2 TEST PROCEDURE 28 7.3 TEST SETUP 28 7.4 EUT OPERATION CONDITIONS 28 7.5 TEST RESULTS 28 8. PEAK OUTPUT POWER TEST 29 8.1 LIMIT 29 8.2 TEST PROCEDURE 29 8.3 TEST SETUP 29 8.4 EUT OPERATION CONDITIONS 29 8.5 TEST RESULTS 29 9. ANTENNA REQUIREMENT 30 9.1 STANDARD REQUIREMENT 30 9.2 EUT ANTENNA 30 APPENDIX I - TEST RESULTS 31 1. DUTY CYCLE 31 2. BANDWIDTH 34 3. MAXIMUM CONDUCTED OUTPUT POWER 39 4. MAXIMUM POWER SPECTRAL DENSITY 42 5. UNWANTED EMISSIONS IN NON-RESTRICTED FREQUENCY BANDS 45 APPENDIX II - MEASUREMENT PHOTOS 52 Report No.: LGT26G035RF02 Page 5 of 52 Revision History Rev. Issue Date Revisions 00 Jul. 29, 2026 Initial Issue Report No.: LGT26G035RF02 Page 6 of 52 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 Part 15.247 Meas Guidance v05r02. FCC P…

Text truncated - open the document above for the full version.