2BORL-BNP-SCREENSBNP Screens

Muizelstraat 2 B-8560 Wevelgem TWIST User Guide 1 User manual t t Twist_User_Guide - 20251223 Purpose of this guide : This guide will explain how the BNP_Screen device can be controlled for testing purposes. This device usually controls AC motors but we have chusen to replace these by an equivalent load of light bulbs because of shipping weight. Setup: The setup contains the following items: (See images below) 1. BNP Screen device 2. Twist Gateway with USB C cable 3. 3 pin AC power cable with plug 4. 4 pin connector cable with lightbulbs Please connect the 4 pin connector cable to 1 of the 3 matching connectors on the BNP Screen device. Please connect the 3 pin connector cable to the matching connector on the BNP Screen device. Plugin a ethernet cable into the Twist Gateway and connect to the internet. Plug USB C cable into Twist Gateway. Connect USB cable to USB power supply (5V). Power both the Twist Gateway and BNP Screen Device by connecting them to the grid power. 1 Muizelstraat 2 B-8560 Wevelgem 2 User manual t t Twist_User_Guide - 20251223 USB 5V 2A Connect to ethernet Connect 3pins connector Connect 4pins connector to 1 of the 3 channels 1x BNP_Screen 1x Gateway Explenation: The BNP Screen Device can be controlled over the internet. The Twist Gateway is connected to the internet and receives the control signals from the GUI in the web browser. The Twist Gateway sends these signals over the Twist network (2.4GHz) to con- trol one or more outputs of the BNP Screen device. We already setup a pre-made network between the BNP Screen device and the Twist Gateway for this test. In this case the lightbulbs will be controlled instead of an AC motor. 1. Go to the website: https://portal-staging.twist-innovation.com 2. Log in with the following credentials: Email: [email protected] PW: TWCert1f1cat1on!! 3. navigate to Installations 4. Find the correct Isntallation by pressing “view details” next to Certification Muizelstraat 2 B-8560 Wevelgem 3 User manual t t Twist_User_Guide - 20251223 Instructions: You can control the SCREEN outputs by pressing the buttons or adjusting the slider Muizelstraat 2 B-8560 Wevelgem 4 User manual t t Twist_User_Guide - 20251223 FCC Statement N OTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help C hanges or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. T his device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Exposure Statement: This equipment complies with FCC radiation exposure limits set f orth for an uncontrolled environment. This equipment shall be installed and oper ated with minimum distance 20cm between the radiator & body.

Twist Innovation BV Muizelstraat 2, 8560 Wevelgem, Belgium Attestation Statements Not Covered Entity Applicant & Not Covered Equipment To: Federal Communications Commission Date: March 27, 2026 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(i) & (ii) FCC ID: 2BORL-BNP-SCREENS Twist Innovation BV (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List, established pursuant to § 1.50002 of reference chapter, as an entity producing “covered” communication equipment. The equipment for which authorization is sought is not “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List that prohibited from receiving an equipment authorization pursuant to section § 2.903 of the FCC rules. Sincerely yours, Applicant Signature Printed Name: Nico Volckaert Title: Manager Address: Muizelstraat 2, 8560 Wevelgem, Belgium FRN: 0036918811 Tel.: +32480661440 Email: [email protected]

Twist Innovation BV Muizelstraat 2, 8560 Wevelgem, Belgium 1 | P a g e Attestation Statements To: Federal Communications Commission Date: March 27, 2026 7435 Oakland Mills Road, Columbia, MD 21046, USA Subject: Attestation of Compliance with FCC Covered List Software Requirements FCC ID: 2BORL-BNP-SCREENS Product Name: BNP Screens This letter serves as an attestation that the equipment identified above ☐ is / ☒ is not (select one) "covered" software as defined under the Federal Communications Commission (FCC) Covered List requirements, as outlined in FCC 22-84 and KDB 986446. Specifically, the undersigned certifies that the equipment for which authorization is sought: 1. Does not contain cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors, assignees, parents, subsidiaries, affiliates, or any entity that has rebranded or relabeled software produced by the aforementioned entities. 2. Does not have the capability to store, run, or deliver any software identified on the FCC Covered List, including but not limited to cybersecurity and anti-virus software. To support this attestation, the appendix evaluation documentation has been prepared and is included in the certification filing. This attestation is based on a thorough evaluation of the device's design, functionality, and software environment. The undersigned affirms that the information provided is accurate and complete to the best of their knowledge. Sincerely yours, Applicant Signature Printed Name: Nico Volckaert Title: Manager Address: Muizelstraat 2, 8560 Wevelgem, Belgium FRN: 0036918811 Tel.: +32480661440 Email: [email protected] Twist Innovation BV Muizelstraat 2, 8560 Wevelgem, Belgium 2 | P a g e Evaluation regarding to the Covered List Software: Compliance Methodology Evaluation Process Results Device is Inherent compliance ☒ The Chipset(s) used is limited to run the Cybersecurity or anti-virus software. Compliance ☒ The Memory used is limited to run the Cybersecurity or anti-virus software. Compliance ☒ There is storage capacity limitation for store or install the Cybersecurity or anti-virus software. Compliance ☒ Operating system used is limited to run, install or deliver the Cybersecurity or anti-virus software. Compliance Device is not Inherent compliance ☐ Evaluation Based on Software Bill of Materials (SBoM) See attached “SBoM“ Note:The SBoM content is limited to the scope of covered list software (e.g. antivirus and cybersecurity software). ☐ Evaluation Based on Scan for Software on the device ☐ Evaluation Based on Filesystem scan ☐ Evaluation Based on Running software check SBOM (Software Bill of Materials) [For Device is not Inherent compliance] Section Component Name Version Supplier 1 2 3

2.911 (d)(7)USA Agent v1.2 Section 2.911(d)(7) USA Agent for Service of Process Company name: Twist Innovation BV Address: Muizelstraat 2, 8560 Wevelgem, Belgium FCC ID: 2BORL-BNP-SCREENS Date: Mar. 12, 2026 2.911(d)(7) USA Designated Agent for Service of Process We, [Twist Innovation BV] (“the applicant”) designate [Wedo Group] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We Acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We Acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Company name: Wedo Group Address: 710 Arabian Ln Walnut, CA 91789, United States FRN：0037730611 Contact Name: Jeffrey Chen Telephone No: (323) 528-1888 Email: [email protected] Applicant Company name: Twist Innovation BV Address: Muizelstraat 2, 8560 Wevelgem, Belgium FRN: 0036918811 Contact Name: Nico Volckaert Telephone No: +32480661440 Email: [email protected] Signature: Signature:

Twist Innovation BV Muizelstraat 2, 8560 Wevelgem, Belgium Mar. 12, 2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization for FCC ID: 2BORL-BNP-SCREENS I, the undersigned, hereby authorize (Attestation of Global Compliance (Shenzhen) Co., Ltd) to act on our behalf in all matters relating to this application for equipment certification. Any act carried out by (Attestation of Global Compliance (Shenzhen) Co., Ltd) shall have the same effect as our own and I acknowledge that all responsibility for complying with the terms and conditions of certification, as specified by DERYCOM CERTIFICATION SERVICES, INC., still resides with Twist Innovation BV We certify that we are not subject to a denial of federal benefits that includes FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862, and that no party to the application, as defined in 47 CFR §1.2002(b), is subject to a denial of federal benefits that includes FCC benefits pursuant to that section. Sincerely, Full name of contact person listed on FCC’s website: Nico Volckaert Title: Manager Tel: +32480661440 Email: [email protected]

Report No.: AGC02762260105AP03 Page 1 of 4 EXTERNAL PHOTOS TOP VIEW OF EUT BOTTOM VIEW OF EUT Report No.: AGC02762260105AP03 Page 2 of 4 FRONT VIEW OF EUT BACK VIEW OF EUT Report No.: AGC02762260105AP03 Page 3 of 4 LEFT VIEW OF EUT RIGHT VIEW OF EUT Report No.: AGC02762260105AP03 Page 4 of 4 PORT VIEW OF EUT ****************************************End of Report*************************************

FCC ID Label Location 40mm*50mm FCC ID: 2BORL-BNP-SCREENS

Report No.: AGC02762260105AP03 Page 1 of 2 INTERNAL PHOTOS OPEN VIEW OF EUT INTERNAL VIEW OF EUT (FIGURE 1) BT Antenna Report No.: AGC02762260105AP03 Page 2 of 2 INTERNAL VIEW OF EUT (FIGURE 2) INTERNAL VIEW OF EUT (FIGURE 3) ****************************************End of Report*************************************

Page 1 of 10 RF Exposure Report Report No.: AGC02762260105FH01 FCC ID : 2BORL-BNP-SCREENS APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : BNP Screens BRAND NAME : TWIST MODEL NAME : BNP Screens APPLICANT : Twist Innovation BV DATE OF ISSUE : Mar. 12, 2026 STANDARD(S) : FCC Part 2 Subpart J §2.1091 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC02762260105FH01 Page 2 of 10 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Mar. 12, 2026 Valid Initial Release Report No.: AGC02762260105FH01 Page 3 of 10 Table of Contents 1. General Information ........................................................................................................................................ 4 2. Product Information ........................................................................................................................................ 5 2.1 Product Technical Description ................................................................................................................... 5 3. Test Environment ............................................................................................................................................ 6 3.1 Address Of The Test Laboratory ............................................................................................................... 6 3.2 Test Facility ................................................................................................................................................ 6 3.3 Environmental Conditions ......................................................................................................................... 7 4. Mobile Device Evaluation Method and Limit ................................................................................................ 8 5. Measurement Results ..................................................................................................................................... 9 6. Measurement Evaluation ................................................................................................................................ 9 Report No.: AGC02762260105FH01 Page 4 of 10 1. General Information Applicant Twist Innovation BV Address Muizelstraat 2, 8560 Wevelgem, Belgium Manufacturer Twist Innovation BV Address Muizelstraat 2, 8560 Wevelgem, Belgium Factory Twist Innovation BV Address Muizelstraat 2, 8560 Wevelgem, Belgium Product Designation BNP Screens Brand Name TWIST Test Model BNP Screens Series Model(s) N/A Difference Description N/A Date of receipt of test item Jan. 16, 2026 Date of Test Jan. 16, 2026 to Mar. 12, 2026 Deviation from Standard No any deviation from the test method Condition of Test Sample Normal Test Result Pass Test Report Form No AGCER-FCC-RF Exposure-V1 Note: The test results of this report relate only to the tested sample identified in this report. Prepared By Jack Gui (Project Engineer) Mar. 12, 2026 Reviewed By Bibo Zhang (Reviewer) Mar. 12, 2026 Approved By Angela Li (Authorized Officer) Mar. 12, 2026 Report No.: AGC02762260105FH01 Page 5 of 10 2. Product Information 2.1 Product Technical Description Frequency Band (Operating) WLAN: 2.412GHz ~ 2.462GHz WLAN: 5.18GHz ~ 5.32GHz / 5.50GHz ~ 5.70GHz WLAN: 5.745GHz ~ 5.825GHz Bluetooth: 2.402GHz ~ 2.480GHz SRD_2.4G: 2.402GHz ~ 2.480GHz Other: 462.5500-462.7250MHz, 462.5625-462.7125MHz 467.5500-467.7250MHz Hardware Version 01.02 Software Version 0.1.0-rc.12 Modulation Type GFSK Device Category Portable (<20cm separation) Mobile (>20cm separation) Others: Antenna Diversity Single antenna Multiple antennas Tx diversity Rx diversity Tx/Rx diversity Antenna Designation Wire antenna Antenna Gain 3.648dBi Minimum Assessment Distance 20cm Evaluation Applied MPE Evaluation SAR Evaluation Report No.: AGC02762260105FH01 Page 6 of 10 3. Test Environment 3.1 Address Of The Test Laboratory Laboratory: Attestation of Global Compliance (Shenzhen) Co., Ltd. Address: 1-2/F, Building 19, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China 3.2 Test Facility The test facility is recognized, certified, or accredited by the following organizations: CNAS-Lab Code: L5488 Attestation of Global Compliance (Shenzhen) Co., Ltd. has been assessed and proved to follow CNAS-CL01 Accreditation Criteria for Testing and Calibration Laboratories (identical to ISO/IEC17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories.) A2LA-Lab Cert. No.: 5054.02 Attestation of Global Compliance (Shenzhen) Co., Ltd. EMC Laboratory has been accredited by A2LA for technical competence in the field of electrical testing, and proved to follow ISO/IEC 17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirements in the identified field of testing. FCC-Registration No.: 975832 Attestation of Global Compliance (Shenzhen) Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the FCC (Federal Communications Commission). The acceptance letter from the FCC is maintained in our files with Registration 975832. IC-Registration No.: 24842(CAB identifier: CN0063) Attestation of Global Compliance (Shenzhen) Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the Certification and Engineering Bureau of Industry Canada. The acceptance letter from the IC is maintained in our files with Registration 24842. Report No.: AGC02762260105FH01 Page 7 of 10 3.3 Environmental Conditions Normal Conditions Temperature range (°C) 15 - 35 Relative humidity range 20 % - 75 % Pressure range (kPa) 86 - 106 Power supply AC230V 50Hz Report No.: AGC02762260105FH01 Page 8 of 10 4. Mobile Device Evaluation Method and Limit Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE limits adopted by the FCC fo…

Text truncated - open the document above for the full version.

Page 1 of 63 FCCTestReport ReportNo.:AGC02762260105FR01 FCCID: 2BORL-BNP-SCREENS APPLICATIONPURPOSE: OriginalEquipment PRODUCTDESIGNATION:BNPScreens BRANDNAME:TWIST MODELNAME:BNPScreens APPLICANT:TwistInnovationBV DATEOFISSUE:Mar.12,2026 STANDARD(S):FCCPart15SubpartC§15.247 REPORTVERSION:V1.0 AttestationOfGlobalCompliance(Shenzhen)Co.,Ltd ReportNo.:AGC02762260105FR01 Page2of63 ReportReviseRecord ReportVersionReviseTimeIssuedDateValidVersionNotes V1.0/Mar.12,2026ValidInitialRelease ReportNo.:AGC02762260105FR01 Page3of63 TableofContents 1.GeneralInformation..........................................................................................................................................5 2.ProductInformation..........................................................................................................................................6 2.1ProductTechnicalDescription....................................................................................................................6 2.2TestFrequencyList.....................................................................................................................................6 2.3RelatedSubmittal(S)/Grant(S).................................................................................................................7 2.4TestMethodology........................................................................................................................................7 2.5SpecialAccessories....................................................................................................................................7 2.6EquipmentModifications.............................................................................................................................7 2.7AntennaRequirement.................................................................................................................................7 3.TestEnvironment..............................................................................................................................................8 3.1AddressoftheTestLaboratory...................................................................................................................8 3.2TestFacility..................................................................................................................................................8 3.3EnvironmentalConditions...........................................................................................................................9 3.4MeasurementUncertainty...........................................................................................................................9 3.5ListofEquipmentUse...............................................................................................................................10 4.SystemTestConfiguration.............................................................................................................................12 4.1EUTConfiguration....................................................................................................................................12 4.2EUTExercise............................................................................................................................................12 4.3ConfigurationofTestedSystem................................................................................................................12 4.4EquipmentUsedInTestedSystem..........................................................................................................13 4.5SummaryofTestResults..........................................................................................................................14 5.DescriptionofTestModes.............................................................................................................................15 6.DutyCycleMeasurement...............................................................................................................................17 7.RFOutputPowerMeasurement....................................................................................................................18 7.1ProvisionsApplicable................................................................................................................................18 7.2MeasurementProcedure..........................................................................................................................18 7.3MeasurementSetup(BlockDiagramofConfiguration)...........................................................................18 7.4MeasurementResult.................................................................................................................................19 8.6dBBandwidthMeasurement.......................................................................................................................23 8.1ProvisionsApplicable................................................................................................................................23 8.2MeasurementProcedure..........................................................................................................................23 8.3MeasurementSetup(BlockDiagramofConfiguration)...........................................................................23 8.4MeasurementResults...............................................................................................................................24 9.PowerSpectralDensityMeasurement.........................................................................................................31 9.1ProvisionsApplicable................................................................................................................................31 9.2MeasurementProcedure..........................................................................................................................31 9.3MeasurementSetup(BlockDiagramofConfiguration)...........…

Text truncated - open the document above for the full version.

ReportNo.:AGC02762260105FR01 Page41of63 Test_Graph_SRD_2.4G_ANT1_2480_1Mbps_HigherBandEmissions Test_Graph_SRD_2.4G_ANT1_2402_2Mbps_ReferenceLevel ReportNo.:AGC02762260105FR01 Page42of63 Test_Graph_SRD_2.4G_ANT1_2402_2Mbps_LowerBandEmissions Test_Graph_SRD_2.4G_ANT1_2402_2Mbps_HigherBandEmissions ReportNo.:AGC02762260105FR01 Page43of63 Test_Graph_SRD_2.4G_ANT1_2440_2Mbps_ReferenceLevel Test_Graph_SRD_2.4G_ANT1_2440_2Mbps_LowerBandEmissions ReportNo.:AGC02762260105FR01 Page44of63 Test_Graph_SRD_2.4G_ANT1_2440_2Mbps_HigherBandEmissions Test_Graph_SRD_2.4G_ANT1_2480_2Mbps_ReferenceLevel ReportNo.:AGC02762260105FR01 Page45of63 Test_Graph_SRD_2.4G_ANT1_2480_2Mbps_LowerBandEmissions Test_Graph_SRD_2.4G_ANT1_2480_2Mbps_HigherBandEmissions ReportNo.:AGC02762260105FR01 Page46of63 TestGraphsofBandEdgeEmissionsinNon-RestrictedFrequencyBands Test_Graph_SRD_2.4G_ANT1_2402_1Mbps_LowerBandEdgeEmissions Test_Graph_SRD_2.4G_ANT1_2480_1Mbps_HigherBandEdgeEmissions ReportNo.:AGC02762260105FR01 Page47of63 Test_Graph_SRD_2.4G_ANT1_2402_2Mbps_LowerBandEdgeEmissions Test_Graph_SRD_2.4G_ANT1_2480_2Mbps_HigherBandEdgeEmissions ReportNo.:AGC02762260105FR01 Page48of63 11.RadiatedSpuriousEmission 11.1MeasurementLimit  FCCPart15.209Limitinthebelowtabletobefollowed Frequencies (MHz) FieldStrength (microvolts/meter) MeasurementDistance (meters) 0.009~0.4902400/F(kHz)300 0.490~1.70524000/F(kHz)30 1.705~30.03030 30~881003 88~2161503 216~9602003 Above9605003 Note:Allmodesweretestedforrestrictedbandradiatedemission,thetestrecordsreportedbelowaretheworst resultcomparedtoothermodes. 11.2MeasurementProcedure 1.TheEUTwasplacedonthetopoftheturntable0.8or1.5meteraboveground.Thephasecenterofthe receivingantennamountedonthetopofaheight-variableantennatowerwasplaced3metersfaraway fromtheturntable. 2.PowerontheEUTandallthesupportingunits.Theturntablewasrotatedby360degreestodeterminethe positionofthehighestradiation. 3.Theheightofthebroadbandreceivingantennawasvariedbetweenonemeterandfourmetersabove groundtofindthemaximumemissionsfieldstrengthofbothhorizontalandverticalpolarization. 4.Foreachsuspectedemission,theantennatowerwasscan(from1Mto4M)andthentheturntablewas rotated(from0degreeto360degrees)tofindthemaximumreading. 5.Setthetest-receiversystemtoPeakorCISPRquasi-peakDetectFunctionwithspecifiedbandwidthunder MaximumHoldMode. 6.Foremissionsabove1GHz,insertthe2.4GfilterbetweenthereceivingantennaandthePre-amplifier(only forRadiatedSpuriousEmission).Use1MHzRBWand3MHzVBWforpeakreading.Placethe measurementantennaawayfromeachareaoftheEUTdeterminedtobeasourceofemissionsatthe specifiedmeasurementdistance,whilekeepingthemeasurementantennaaimedatthesourceof emissionsateachfrequencyofsignificantemissions,withpolarizationorientedformaximumresponse. ThemeasurementantennamayhavetobehigherorlowerthantheEUT,dependingontheradiation patternoftheemissionandstayingaimedattheemissionsourceforreceivingthemaximumsignal.The finalmeasurementantennaelevationshallbethatwhichmaximizestheemissions.Themeasurement antennaelevationformaximumemissionsshallberestrictedtoarangeofheightsoffrom1mto4m abovethegroundorreferencegroundplane. 7.Whentheradiatedemissionslimitsareexpressedintermsoftheaveragevalueoftheemissions,and pulsedoperationisemployed,themeasurementfieldstrengthshallbedeterminedbyaveragingoverone completepulsetrain,includingblankingintervals,aslongasthepulsetraindoesnotexceed0.1seconds. ReportNo.:AGC02762260105FR01 Page49of63 8.Asanalternative(providedthetransmitteroperatesforlongerthan0.1seconds)orincaseswherethe pulsetrainexceeds0.1seconds,themeasuredfieldstrengthshallbedeterminedfromtheaverage absolutevoltageduringa0.1secondintervalduringwhichthefieldstrengthisatitsmaximumvalues. 9.IftheemissionsleveloftheEUTinpeakmodewas3dBlowerthantheaveragelimitspecified,then testingwillbestoppedandpeakvaluesofEUTwillbereported,otherwise,theemissionswhichdonot have3dBmarginwillberepeatedonebyoneusingthequasi-peakmethodforbelow1GHz. 10.Fortestingabove1GHz,theemissionsleveloftheEUTinpeakmodewaslowerthanaveragelimit(that meanstheemissionslevelinpeakmodealsocomplieswiththelimitinaveragemode),thentestingwillbe stoppedandpeakvaluesofEUTwillbereported,otherwise,theemissionswillbemeasuredinaverage modeagainandreported. 11.Incasetheemissionislowerthan30MHz,loopantennahastobeusedformeasurementandtherecorded datashouldbeQPmeasuredbyreceiver.High-Lowscanisnotrequiredinthiscase. Thefollowingtableisthesettingofspectrumanalyzerandreceiver. SpectrumParameterSetting Start~StopFrequency9kHz~150kHz/RB200HzforQP Start~StopFrequency150kHz~30MHz/RB9kHzforQP Start~StopFrequency30MHz~1000MHz/RB120kHzforQP Start~StopFrequency 1GHz~26.5GHz 1MHz/3MHzforPeak,1MHz/3MHzforAverage ReceiverParameterSetting Start~StopFrequency9kHz~150kHz/RB200HzforQP Start~StopFrequency150kHz~30MHz/RB9kHzforQP Start~StopFrequency30MHz~1000MHz/RB120kHzforQP ReportNo.:AGC02762260105FR01 Page50of63 Quasi-PeakMeasurementsbelow1GHz 1.Analyzercenterfrequencywassettothefrequencyoftheradiatedspuriousemissionofinterest 2.Spanwassetgreaterthan1MHz 3.RBW=asshowninthetableabove 4.Detector=CISPRquasi-peak 5.Sweeptime=autocouple 6.Tracewasallowedtostabilize PeakMeasurementsabove1GHz 1.Analyzercenterfrequencywassettothefrequencyoftheradiatedspuriousemissionofinterest 2.RBW=1MHz 3.VBW=3MHz 4.Detector=peak 5.Sweeptime=autocouple 6.Tracemode=maxhold 7.Tracewasallowedtostabilize AverageMeasurementsabove1GHz 1.Analyzercenterfrequencywassettothefrequencyoftheradiatedspuriousemissionofinterest 2.RBW=1MHz 3.VBW≥[3×RBW] 4.Detector=Poweraveraging(rms) 5.Averagingtype=power(i.e.,rms) 6.Sweeptime=auto 7.Performatraceaverageofatleast100traces. 8.Theapplicablecorrectionfactoris[10*log(1/D)],whereDisthedutycycle.Thefactorhadbeeneditedin the“InputCorrection”oftheSpectrumAnalyzer. ReportNo.:AGC02762260105FR01 Page51of63 11.3MeasurementSetup(BlockDiagramofConfiguration) RadiatedEmissionTestSetup9kHz-30MHz RadiatedEmissionTestSetup30MHz-1000MHz RadiatedEmissionTestSetupAbove1000MHz ReportNo.:AGC02762260105FR01 Page52of63 11.4MeasurementResult…

Text truncated - open the document above for the full version.

Page 1 of 13 Antenna Test Report Report No.: AGC16962250402PA01 PRODUCT DESIGNATION : TWIST Indoor Gateway BRAND NAME : TWIST MODEL NAME : FU.01.03 APPLICANT : Twist Innovation BV DATE OF ISSUE : May 15, 2025 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No…

Text truncated - open the document above for the full version.