2BOZA-N0358Chicco Flippable Milk Warmer USA

PORTABLE Bottle Warmer + Sterilizer IS0257ES_02 06/26 ©2026 Artsana USA, Inc. ChiccoUSA.com Owner’s Manual Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE. 2 3 WARNING WHEN USING THIS ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING: Take Time to Read This Owner’s Manual BURN HAZARD To avoid risk of burns: • Bottle warmer components and water temperature can be very hot. Avoid direct contact with hot water and steam. Handle with care. • DO NOT touch surfaces that may be hot. Wait until all parts of the unit have cooled before touching them or cleaning. • Bottles will be hot; remove with care. • Before serving, be sure the contents of the bottle is at a safe temperature. • DO NOT move the bottle warmer while warming or sterilizing. • DO NOT obstruct the steam outlets on the top of the sterilizing lid. • NEVER use without liquid. WARNINGSWARNINGS WARNING • This appliance must not be used by children. This is NOT a toy. Keep out of reach of children. • Close supervision is necessary when any appliance is used near children. • For household and portable use in a dry location only. • Only use this appliance for its intended use. DO NOT modify or alter the bottle warmer. • DO NOT use accessories, spare parts, or any components not supplied or approved by Chicco as they may cause injuries or damage. • DO NOT use with any bottle that is not intended to be heated. • DO NOT place on or near a hot gas or electric burner, or in a heated oven. • NOT for space heating purposes. • Inspect carefully before each use. DO NOT operate any appliance after the appliance malfunctions or is dropped or damaged in any manner. If the bottle warmer is faulty and/or not working correctly, switch it off immediately. 4 5 WARNINGSWARNINGS WARNING • To protect against electrical shock DO NOT immerse the bottle warmer in water. • DO NOT use if the bottle warmer accidentally falls into water or becomes submerged. • This product has a built-in lithium battery that cannot be replaced. • Use only with Listed/Certified Information Technology Equipment Power Supply. • Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. • DO NOT use an appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury. • DO NOT expose an appliance to fire or excessive temperature. Exposure to fire or temperature above 265°F (130°C) may cause explosions. WARNING • Follow all charging instructions and do not charge the appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire. • Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained. • DO NOT modify or attempt to repair the appliance except as indicated in the instructions for use and care. 6 7 ADAPTER LIST Below is a list of included adapters and their compatible bottles. You can find the adapter letter printed on the side of the adapter. • Adapter A - Dr. Brown’s Narrow / Medela • Adapter C - Chicco / Avent • Adapter D - MAM • Adapter F - Tommee Tippee • Adapter H - Comotomo Gen 1 / Haakaa / Boon Nursh • Adapter I - Lansinoh / Pigeon / Evenflo Wide • Adapter J - Dr. Brown’s Wide • Adapter K - Comotomo Gen 2 PARTS LIST A C B Bottle WarmerSterilizing Lid Charging Cord Compatible with most popular brands, including: AVENT®, DR. BROWN’S®, MAM®, TOMMEE TIPPEE® and COMOTOMO®. AVENT®, DR. BROWN’S®, MAM®, TOMMEE TIPPEE® and COMOTOMO® are all registered trademarks of their respective owners. This product is not licensed by, affiliated with, or endorsed by Avent Limited, Dr. Brown’s Company, MAM Babyartikel Gesellschaft MBH, Mayborn (UK) Limited or Comotomo. 8 9 CHARGING THE BAT TERY 1 2 3 CHARGING THE BAT TERY Before charging the battery make sure the bottle warmer is turned off. The bottle warmer cannot be used while charging. Charge the battery fully before using. 1 Lift up on the charging port protector on the back of the bottle warmer. 2 Connect the included USB-C end of the charging cord to bottle warmer. 3 Plug the USB-A end of the charging cord into a compatible fast-charging power supply (5-20V main adapter) that is plugged into an outlet to charge. • For faster charging, a fast-charging power supply (5-20V main adapter) can be used with a compatible cable (USBC-USBC). 10 11 CHARGING THE BAT TERY 5 4 CHARGING THE BAT TERY 4 The charging icon will light up. When the bottle warmer is fully charged the charging icon will turn off. 5 Unplug the cord from the back of the bottle warmer and push the charging port protector back into place. 12 13 USING THE BOT TLE WARMER 4B 4A 1 USING THE BOT TLE WARMER 1 Make sure the seal inside the bottle warmer is fully pushed down with the ‘P’ tab facing up. 2 Find the correct adapter for the bottle that is being warmed. Refer to page 7. 3 Pour the amount of liquid (water or milk) you want to heat into the bottle. • NEVER use with less than 30ml of liquid inside the bottle when warming. • NEVER use frozen liquid with this bottle warmer. 4 To prevent leaking, make sure the seal is pushed down firmly into the adapter with the letter tab facing up (4A). Firmly screw the adapter on to the bottle (4B). 14 15 USING THE BOT TLE WARMER 6 5 7 USING THE BOT TLE WARMER 5 Turn the bottle warmer upside down and screw it firmly onto the bottle. 6 Flip the bottle warmer over and place on a flat stable surface. Press and hold the power button for 2 seconds to turn on the interface. • The battery charge status will flash on the display for a few seconds before being replaced by t…

Text truncated - open the document above for the full version.

Artsana USA, Inc. Date: 6/8/2026 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 §2.911 (d)(5) Attestation FCC ID: 2BOZA-N0358 FCC FRN: 0036959542 1.Artsana USA, Inc. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2.Artsana USA, Inc. (“the applicant”) certifies that the device does not have cybersecurity and / or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, identified on the Covered List installed on the device, nor will it be installed by the applicant anytime after certification. 3.Artsana USA, Inc. (“the applicant”) certifies that the RF device is not a router “produced in a foreign country”. 4.Artsana USA, Inc. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment and is not an affiliate or subsidiary of an entity identified on the Covered List. Sincerely yours, Name: Joel Peterson Job Title: Compliance and Quality Manager Company Name: Artsana USA, Inc.

Artsana USA, Inc. Date: 6/8/2026 UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to: a) fulfill the requirements for the scope of certification requested, including implementing any appropriate changes requested by UL Verification Services Telecommunications Certification Body (TCB) and / or the FCC; b) supply any and all information needed for the evaluation of the products for which certification is sought; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) not use our product certification in such a manner as to bring the TCB or FCC into disrepute and to not make any statement regarding product certification which the TCB or FCC may consider misleading or unauthorized; e) discontinue use of all advertising matter that contains any reference thereto and complies with any and all actions required by the FCC upon suspension or cancellation of certification; f) use certification only to indicate that products are certified in conformity with specified standards; g) endeavor to ensure that no certificate or report or any part thereof is used in a misleading manner, and any copies of the grants/certificates shall be reproduced in their entirety; h) comply with the requirements of the TCB and FCC, including the use of marks and label information prescribed for the scope of certification, when making reference to product certification in communication media such as documents, brochure or advertisements; i) comply with the requirements for certification, supply any information needed for evaluation of products to be certified and, where applicable, make provision for the participation of observers; j) ensure that products marketed under the scope of the requested certification continue to comply with the certification requirements; k)provide a sample of a production unit for testing within 30 days of the request should this product be selected as part of either the TCB’s or the FCC’s market surveillance requirements; l)keep a record of all complaints relating to product’s compliance with requirements of relevant standard; make records available to UL or FCC when requested; take appropriate action with respect to such complaints and any deficiencies found in the product that affect compliance with requirements for certification; document the actions taken with respect to complaints and/or deficiencies; m)inform the TCB immediately of any changes that may affect its ability to comply with the certification requirements. This authorization is valid until further written notice from the applicant. Sincerely Yours, Company Name: Artsana USA, Inc. Contact Name: Joel Peterson Title of Person: Compliance and Quality Manager Address: 1826 William Penn Way, Lancaster, Pennsylvania, 17601 United States Date: 0608/2026

Artsana USA, Inc. Date: 6/8/2026 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 §2.911 (d)(7) Agent Designation Attestation Grantee Code: 2BOZA Applicant (Grantee) FRN: 0036959542 To whom it may concern: Artsana USA, Inc. (“the applicant”) as required by section §2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC Grantee Code. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility under CFR 47 §2.929(c) to inform the FCC whenever the agent information changes. U.S. Agent Information: Contact Person: Joel Peterson Company Name: Artsana USA, Inc. FCC FRN: 0036959542 Company US Address: 1826 William Penn Way, Lancaster, Pennsylvania, 17601 United States Email: [email protected] Sincerely yours, Contact Person: Joel Peterson Company Name: Artsana USA, Inc. Company Address: 1826 William Penn Way, Lancaster, Pennsylvania, 17601 United States

Artsana USA, Inc. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2BOZA-N0358 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: Artsana USA, Inc. Contact Name: Joel Peterson Title of Person: Compliance and Quality Manager Address: 1826 William Penn Way, Lancaster, Pennsylvania, 17601 United States Date: 0608/2026

External Photographs Page 2 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. External Page 3 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Page 4 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch.

Note: 1. This label will be Laser carved label and cannot be removed. 2. The FCC label statement will be included in the user manual which will be printed on a paper insert and sold with the device. 3. Label information is location on the bottom of the device.

Internal Photographs Page 2 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Page 3 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Page 4 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Page 5 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Page 6 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch.

The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. FCC 47 CFR Part 15 Subpart B TEST REPORT For Chicco Flippable Milk Warmer USA MODEL NUMBER: N0358 REPORT NUMBER: 4792188332.2.1-EMC-1 FCC ID: 2BOZA-N0358 ISSUE DATE: July 3, 2026 Prepared for Artsana USA, Inc. 1826 William Penn Way, Lancaster, Pennsylvania, 17601 United States Prepared by UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch Room 101, Building 2, No.4, Information Road, Songshan Lake, Dongguan, Guangdong, China Tel: +86 769 22038881 Fax: +86 769 33244054 Website: www.ul.com REPORT NO.: 4792188332.2.1-EMC-1 Page 2 of 17 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Revision History Rev. Issue Date Revisions Revised By V0 July 3, 2026 Initial Issue REPORT NO.: 4792188332.2.1-EMC-1 Page 3 of 17 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Summary of Test Results Emission Standard Test Item Limit Result FCC 47 CFR Part 15 Subpart B Conducted emissions FCC Part 15.107 Pass Radiated emissions below 1GHz FCC Part 15.109 Pass Radiated emissions above 1GHz FCC Part 15.109 N/A (NOTE 1, 2) Note: 1. N/A: In this whole report not applicable. 2. If the highest frequency of the internal sources of the EUT is less than 108 MHz, the measurement shall only be made up to 1 GHz; If the highest frequency of the internal sources of the EUT is between 108 MHz and 500 MHz, the measurement shall only be made up to 2 GHz; If the highest frequency of the internal sources of the EUT is between 500 MHz and 1 GHz, measurement shall only be made up to 5 GHz; If the highest frequency of the internal sources of the EUT is above 1 GHz, the measurement shall be made up to 5 times the highest frequency or 40 GHz, whichever is less. *This test report is only published to and used by the applicant, and it is not for evidence purpose in China. *The measurement result for the sample received is <Pass> according to <FCC 47 CFR Part 15 Subpart B> when <Simple Acceptance> decision rule is applied. Decision rule for statement of conformity: The measurement uncertainty is not taken into account for statement of conformity. REPORT NO.: 4792188332.2.1-EMC-1 Page 4 of 17 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. CONTENTS 1. ATTESTATION OF TEST RESULTS ..................................................................................... 5 2. TEST METHODOLOGY ......................................................................................................... 6 3. FACILITIES AND ACCREDITATION ..................................................................................... 6 4. CALIBRATION AND UNCERTAINTY ................................................................................... 7 4.1. MEASURING INSTRUMENT CALIBRATION ........................................................... 7 4.2. MEASUREMENT UNCERTAINTY ............................................................................ 7 5. EQUIPMENT UNDER TEST .................................................................................................. 8 5.1. DESCRIPTION OF EUT ........................................................................................... 8 5.2. TEST MODE ............................................................................................................. 8 5.3. EUT ACCESSORY ................................................................................................... 8 5.4. SUPPORT UNITS FOR SYSTEM TEST ................................................................... 8 6. MEASURING EQUIPMENT AND SOFTWARE USED........................................................... 9 7. EMISSION TEST ................................................................................................................. 10 7.1. CONDUCTED EMISSIONS .................................................................................... 10 7.2. RADIATED EMISSIONS BELOW 1GHZ ................................................................. 14 REPORT NO.: 4792188332.2.1-EMC-1 Page 5 of 17 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. 1. ATTESTATION OF TEST RESULTS Applicant Information Company Name: Artsana USA, Inc. Address: 1826 William Penn Way, Lancaster, Pennsylvania, 17601 United States Manufacturer Information Company Name: Artsana USA, Inc. Address: 1826 William Penn Way, Lancaster, Pennsylvania, 17601 United States EUT Information EUT Name: Chicco Flippable Milk Warmer USA Model: N0358 Brand: Chicco Sample Received Date: April 24, 2026 Sample Status: Normal Sample ID: 9676476 Date of Tested: April 30, 2026 to May 8, 2026 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC 47 CFR Part 15 Subpart B Pass Prepared By: Checked By: Karl Wu Kebo Zhang Engineer Project Associate Operations Leader Approved By: Stephen Guo Operations Manager REPORT NO.: 4792188332.2.1-EMC-1 Page 6 of 17 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FOR…

Text truncated - open the document above for the full version.

Appendix II Setup Photographs RADIATED RF MEASUREMENT SETUP (30MHz~1GHz) AC CONDUCTED POWER LINE SETUP