2BP4BW9Super Mini Walkie-Talkie

CAUTION: This Super Mini Walkie-Talkie is the product with excellent design and advanced technology. The following suggestions will help you fulfill your obligations under warranty terms and understand the safety knowledge of using Super Mini Walkie-Talkie. 1.Don't try to disassemble the Super Mini Walkie-Talkie. Unauthorized disassemble may cause damage to the Super Mini Walkie-Talkie. 2.This machine can use universal qualified mobile phone charger(5V). 3.Don't expose the machine to sun for a long time or put it on a overheated place. 4.Don't p lace it in a dusty or damp place 5.Don't use strong chemicals, cleaning agents or strong lotions to clean Super Mini Walkie-Talkie 6.If it is found to emit peculiar smell or smoke, place it on the open ground to avoid Injury and contact the distributer in time. 7.Don't use the machine inflammable, explosive or other place where Super Mini Walkie-Talkie is prohibited 8.In order to obtain the best communication performance, it is recommended that le ast distance between Super Mini Walkie-Talkie is 2 meters. 9.Pl ease abide the local wireless management regulations, Contact with the distributor if you have any questions. 10.If the machine has not been used for a long time, the battery will automaticallyactivate the protection function. When using it again, please plug the charger intothe machine and keep it charging for more than 30 minutes to ensure normal use. Checklist: Op en the package carefully, check the product and accessoriesaccording to the following list:Please conduct your distributor immediately if any damaged ormissing happened! NO.ItemQTY 1Walkie-talkie1 2Charger Line1 3Earphone2 4User manual1 Antenna Describe The EUT has one integral spring antenna and the maximum antenna gain is 2.15dBi (Peak gain), Frequency Range is 462-468MHz. Function& Description: FunctionDescriptionRemark Channel30 Channelscustomerized VolumeReceiving volume1-8 Battery savingExtending standby time Battery lnformation: When the Super Mini walkie-talkie's battery is low, there will be a voice prompt. Please charge it When the device is being charged, the indicator light turns red. When the device is fully charged, the indicator light turns green. Pull out the silicone plug before charging, as shown in the figure below. Channel and Frequency(MHz) FRS 30CH ChannelFrequencyChannelFrequency 1462.550016467.5500 2462.575017467.5750 3462.600018467.6000 4462.625019467.6250 5462.650020467.6500 6462.675021467.6750 7462.700022467.7000 8462.725023467.7250 9462.562524467.5625 10462.587525467.5875 11462.612526467.6125 12462.637527467.6375 13462.662528467.6625 14462.687529467.6875 15462.712530467.7125 Specification Overall Channel：30 Working tempeature: -20°C~+60°C Standard Voltage: DC 3.7V Capacity of Battery：450mAh Channel Spacing：12.5kHz Outline Size：84mmX19mmX18mm Weight：24g Antenna lmpedance：50Ω Transmitting Part:Receiving Part: Freq Stability: ≤2.5ppm RF power: <0.5W Modulation: F3E Residual: ≤-35dB Audio distortion: ≤3% Sensitivity: ≤-120dBm Adjacent selection: ≥60dB Modulaion Rejection: ≥60dB SNR: ≥48dB Audio Distortion: ≤3% Note: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Note: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: SAR tests are conducted using standard operating positions accepted by the FCC/ISEDC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model is a available for sale, it must be tested and certified to the FCC/ISEDC that it does not exceed the exposure limit established by the FCC/ISEDC. Tests for each product are performed in positions and locations as required by the FCC/ISEDC. For body worn operation, this device has been tested and meets the FCC/ISEDC RF exposure guidelines when used with an accessory designated for this product or when used with and accessory that contains no metal. Your wireless transceiver contains a low power transmitter. This product sends out radio frequency (RF) signals when the Push-to-Talk (PTT) Button is pressed. The device is authorized to operate at a duty factor not to exceed 50%. Operators under the age of 18 will not be held personally responsible, pursuant to § 95.343, for improper operation of a GMRS repeater or base station. The holder of the individual license under which the minor operates is solely responsible for any improper operation that occurs while an individual under the age of 18 is operating the st…

Text truncated - open the document above for the full version.

ATTESTATION STATEMENT Applicant: Quanzhou WeiLuoSai Electronics Co., Ltd. Add: Room 1903, Unit 1, Building 1, Linghaiyuan, No. 50, Quannan Road,Fengze District, Quanzhou City,Fujian Province, China Tel: 13622328970 Email: [email protected] Date: 2025-08-21 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d)(5)(i), (ii) Filing FCC ID: 2BP4BW9 Quanzhou WeiLuoSai Electronics Co., Ltd. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Quanzhou WeiLuoSai Electronics Co., Ltd. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. And our product does not use Kaspersky software information. Sincerely, Signed by (printed name): Zheng shao min Signature:

U.S. AGENT LETTER OF ATTESTATION Date: 2025- 08-21 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2BP4BW9 Quanzhou WeiLuoSai Electronics Co., Ltd. (“the Applicant”) certifies that, as of the date of the filing of the application, ANTEK SERVICE INC is our designated U.S. agent for service of process for the above referenced FCC ID. Quanzhou WeiLuoSai Electronics Co., Ltd. (“the Applicant”) accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. ANTEK SERVICE INC accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: ANTEK SERVICE INC Address: 901 N PENNSYL VANIA ST STE 0 DENVER,CO 80203,United States FRN: 0033437609 Contact Name: Shirley Kwok Tel.: (303) 800-6308 Email: [email protected] Signed by (printed name): Shirley Kwok/ Manager Signature: Applicant: Quanzhou WeiLuoSai Electronics Co., Ltd. Add: Room 1903, Unit 1, Building 1, Linghaiyuan, No. 50, Quannan Road,Fengze District, Quanzhou City,Fujian Province, China FRN: 0037133527 Tel: 13622328970 Email: [email protected] Signed by (printed name): Zheng shao min Signature:

Applicant: Quanzhou WeiLuoSai Electronics Co., Ltd. Add: Room 1903, Unit 1, Building 1, Linghaiyuan, No. 50, Quannan Road,Fengze District, Quanzhou City,Fujian Province, China Tel: 13622328970 Email: [email protected] QA-FR-170-B FCC Authorization Current Date:2025-08-21 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We Quanzhou WeiLuoSai Electronics Co., Ltd., the undersigned, Hereby authorizes Bay Area Compliance Laboratories Corp. (Xiamen) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp. (Xiamen) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Client’s Signature: Client’s Name/Title: Zheng shao min /Manager

Applicant: Quanzhou WeiLuoSai Electronics Co., Ltd. Add: Room 1903, Unit 1, Building 1, Linghaiyuan, No. 50, Quannan Road,Fengze District, Quanzhou City,Fujian Province, China Tel: 13622328970 Email: [email protected] QA-FR-171-A FCC ConfidentialAuthorization Current Date:2025-08-21 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Confidentiality Request regarding application for certification of FCC ID: 2BP4BW9 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, Quanzhou WeiLuoSai Electronics Co., Ltd. hereby request confidential treatment of information accompanying this application as outlined below:  Circuit Description --- (Long term)  Schematic --- (Long term)  Block Diagram --- (Long term)  Tune up procedure--- (Long term)  BOM--- (Long term) The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Client’s Signature: Client’s Name/Title: Zheng shao min /Manager

Bay Area Compliance Laboratories Corp. (Xiamen) Report No.: 2506U30712E-RF-EXP Page 1 / 5 EUT EXTERNAL PHOTOS Bay Area Compliance Laboratories Corp. (Xiamen) Report No.: 2506U30712E-RF-EXP Page 2 / 5 Bay Area Compliance Laboratories Corp. (Xiamen) Report No.: 2506U30712E-RF-EXP Page 3 / 5 Bay Area Compliance Laboratories Corp. (Xiamen) Report No.: 2506U30712E-RF-EXP Page 4 / 5 Bay Area Compliance Laboratories Corp. (Xiamen) Report No.: 2506U30712E-RF-EXP Page 5 / 5

Bay Area Compliance Laboratories Corp. (Xiamen) Report No.: 2506U30712E-RF-INP Page 1 / 4 EUT INTERNAL PHOTOS Bay Area Compliance Laboratories Corp. (Xiamen) Report No.: 2506U30712E-RF-INP Page 2 / 4 Bay Area Compliance Laboratories Corp. (Xiamen) Report No.: 2506U30712E-RF-INP Page 3 / 4 Bay Area Compliance Laboratories Corp. (Xiamen) Report No.: 2506U30712E-RF-INP Page 4 / 4

Note: The information marked # is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP or any agency of the U.S. Government. This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “▼”. Bay Area Compliance Laboratories Corp. (Shenzhen) 5F(B-West) , 6F, 7F, the 3rd Phase of Wan Li Industrial Building D, Shihua Rd, FuTian Free Trade Zone, Shenzhen, China Tel: +86-755-33320018Fax: +86-755-33320008www.baclcorp.com.cn TR-EM-SA005 Page 1 of 47 Version 3.0 TEST REPORT Applicant Name: Quanzhou WeiLuoSai Electronics Co., Ltd. Address: Room 1903, Unit 1, Building 1, Linghaiyuan, No. 50, Quannan Road,Fengze District, Quanzhou City,Fujian Province, China Report Number: 2501U30712E-SA FCC ID: 2BP4BW9 Test Standard (s) FCC 47 CFR part 2.1093 Sample Description Product Name: Super Mini Walkie-Talkie Model No.: W9 Multiple Model(s) No.: N/A Trade Mark: N/A Serial Number: 34X3-1 Date Received: 2025/07/25 Date of Test: 2025/08/06 Issue Date: 2025/08/21 Test Result: Pass ▲ ▲In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: Bob Lu Luke Jiang SAR Engineer SAR Engineer Bay Area Compliance Laboratories Corp.(Shenzhen) Report No.: 2501U30712E-SA TR-EM-SA005 Page 2 of 47 Version 3.0 Attestation of Test Results Frequency Band Max. SAR Level(s) Reported(W/kg) Limit(W/Kg) PTT (462.5500-467.7250MHz) 1g Body SAR 0.22 1.6 Applicable Standards FCC 47 CFR part 2.1093 Radiation exposure evaluation: portable devices RF Exposure Procedures: TCB Workshop April 2019 IEEE 1528:2013 IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques KDB procedures KDB 447498 D01 General RF Exposure Guidance v06 KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04 KDB 865664 D02 RF Exposure Reporting v01r02 KDB 643646 D01 SAR Test for PTT Radios v01r03 Note: This wireless device has been shown to be capable of compliance for localized specific absorption rate (SAR) for General Population/Uncontrolled Exposure limits specified in FCC 47 CFR part 2.1093 and has been tested in accordance with the measurement procedures specified in IEEE 1528-2013 and RF exposure KDB procedures. The results and statements contained in this report pertain only to the device(s) evaluated. Bay Area Compliance Laboratories Corp.(Shenzhen) Report No.: 2501U30712E-SA TR-EM-SA005 Page 3 of 47 Version 3.0 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 4 EUT DESCRIPTION ................................................................................................................................................... 5 TECHNICAL SPECIFICATION ......................................................................................................................................... 5 REFERENCE, STANDARDS, AND GUILDELINES .............................................................................................. 6 SAR LIMITS ................................................................................................................................................................ 6 FACILITIES ................................................................................................................................................................. 7 DESCRIPTION OF TEST SYSTEM .......................................................................................................................... 8 EQUIPMENT LIST AND CALIBRATION ............................................................................................................. 15 EQUIPMENT’S LIST & CALIBRATION INFORMATION ............................................................................................... 15 SAR MEASUREMENT SYSTEM VERIFICATION ............................................................................................. 16 LIQUID VERIFICATION ............................................................................................................................................... 16 SYSTEM ACCURACY VERIFICATION .......................................................................................................................... 17 SAR SYSTEM VALIDATION DATA .................................................................................................................... 18 EUT TEST STRATEGY AND METHODOLOGY ................................................................................................. 19 TEST POSITIONS FOR BODY-WORN AND OTHER CONFIGURATIONS ............................................................................. 19 TEST DISTANCE FOR SAR EVALUATION ................................................................................................................... 19 SAR EVALUATION PROCEDURE ................................................................................................................................ 20 CONDUCTED OUTPUT POWER MEASUREMENT .......................................................................................... 21 TEST PROCEDURE ..............................................................................................................................…

Text truncated - open the document above for the full version.

FCC PART 95 TEST REPORT For Quanzhou WeiLuoSai Electronics Co., Ltd. Room 1903, Unit 1, Building 1, Linghaiyuan, No. 50, Quannan Road,Fengze District, Quanzhou City,Fujian Province, China Report Type: Original Report Product Name: Super Mini Walkie-Talkie Re port Number: 2506U30712E-RF-01 Re port Date: 2025-08-04 Reviewed By: Ash Lin Approved By: Miles Chen Prepared By: Ba y Area Compliance Laboratories Corp. (Xiamen) Unit 102, No. 902 Meifeng South Road, Binhai West Avenue, Science and Technology Innovation Park, Torch High tech Zone XiaMen Tel: +86-592-3200111 www.baclcorp.com.cn FCC ID: 2BP4BW9 Bay Area Compliance Laboratories Corp. (Xiamen) Report No.: 2506U30712E-RF-01 FCC Part 95 Page 2 of 57 TABLE OF CONTENTS REPORT REVISION HISTORY ................................................................................................................................ 4 GENERAL INFORMATION ....................................................................................................................................... 5 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 5 ANTENNA INFORMATION ............................................................................................................................................. 5 OBJECTIVE ................................................................................................................................................................... 5 TEST METHODOLOGY .................................................................................................................................................. 5 MEASUREMENT UNCERTAINTY .................................................................................................................................... 6 TEST FACILITY ............................................................................................................................................................. 6 SYSTEM TEST CONFIGURATION .......................................................................................................................... 7 TEST MODE AND VOLTAGE .......................................................................................................................................... 7 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 7 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 7 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 8 EXTERNAL I/O CABLE .................................................................................................................................................. 8 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 8 SUMMARY OF TEST RESULTS ............................................................................................................................. 10 TEST EQUIPMENT LIST ......................................................................................................................................... 11 FCC §2.1055(D), §95.1765 –GMRS FREQUENCY ACCURACY .......................................................................... 12 APPLICABLE STANDARD ............................................................................................................................................ 12 EUT SETUP BLOCK DIAGRAM ................................................................................................................................... 12 TEST PROCEDURE ...................................................................................................................................................... 12 TEST DATA ................................................................................................................................................................ 13 FCC §2.1046, §95.1767 –RF OUTPUT POWER ...................................................................................................... 16 APPLICABLE STANDARD ............................................................................................................................................ 16 TEST SETUP BLOCK DIAGRAM ................................................................................................................................... 16 TEST PROCEDURE ...................................................................................................................................................... 16 TEST DATA ................................................................................................................................................................ 17 FCC §95.1771-GMRS EMISSION TYPE ................................................................................................................. 20 APPLICABLE STANDARD ............................................................................................................................................ 20 FCC §2.1049, §95.1773, §95.1779 GMRS AUTHORIZED BANDWIDTH AND EMISSION MASK ................ 21 APPLICABLE STANDARD ............................................................................................................................................ 21 EUT SETUP BLOCK DIAGRAM ................................................................................................................................... 22 TEST PROCEDURE ...................................................................................................................................................... 22 TEST DATA ........................................…

Text truncated - open the document above for the full version.

Antenna specification 1.Antenna Describe Antenna plate Integral antenna Model Name A58 Antenna Gain 2.15dBi(Peak gain) Frequency Rang 462-468MHz Company Name Shenzhen Cient Communication Technology Co.,ltd. Address: 501A&B-A Blockk,Donglian Building,Chuangye 2 road,Baoan District,Shenzhen,Guangdong,P.R china 2.Test-up Diagram 3. Antenna Gain 4. Antenna GainRadiation Pattern 462MHz: 465MHz: 468MHz:

Bay Area Compliance Laboratories Corp. (Xiamen) Report No.: 2506U30712E-RF-TSP Page 1 / 2 EUT SETUP PHOTOS RSE-Front View(Below 1GHz) RSE-Back View(Below 1GHz) Bay Area Compliance Laboratories Corp. (Xiamen) Report No.: 2506U30712E-RF-TSP Page 2 / 2 RSE-Front View(Above 1GHz) RSE-Back View(Above 1GHz)