2BP9F-W8HOME USE VISUAL EAR PICK

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Covered Equipment Attestation Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(5)(i)-(ii) of the Commission’s Rules (47 C.F.R.) we attest as follows for the product listed below: FCC ID Model name 2BP9F-W8 W8, W9, W10, W11, W12, W15, W16, W18, W20 We, Applicant Company Name: Shenzhen Boerx Electronics Co.，Ltd. Address: 401， building 10, High-Tech Park, Fuyuanyi Road 156, HePing Community, FuHai Street , BaoAn-Zone, ShenZhen ,GuangDong,China Phone: 13823787280 certify that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. This includes the cybersecurity and anti-virus software produced or provided by Kaspersky Lab, Inc. or any of ist successors and assignees. We certify that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. If you have any questions, please feel free to contact us at the address shown below. Sincerely, Jun.12,2025 Signature Date Printed Name of Signee: Shi bojiang Company: Shenzhen Boerx Electronics Co.，Ltd. Address: 401， building 10, High-Tech Park, Fuyuanyi Road 156, HePing Community, FuHai Street , BaoAn-Zone, ShenZhen ,GuangDong,China Phone: 13823787280 Fax: Email:[email protected]

Local Representative Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(7), of the Commission’s Rules (47 C.F.R.) we attest as follows for the product listed below: FCC ID Model name 2BP9F-W8 W8, W9, W10, W11, W12, W15, W16, W18, W20 We hereby acknowledge as follows: i. both signees confirm that the point of contact accepts responsibility to act as a US- American Representative on behalf of the applicant ii. the point of contact provides the physical U.S. address and email as listed below iii. both parties maintain the requirements of this agreement for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. US-American Point of ContactApplicant/Approval Holder Company Name: FCC US Agent, LLC Shenzhen Boerx Electronics Co., Ltd. FRN: 0033402884 0037165594 Contact Name: Tim Payne Shi bojiang Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA 401， building 10, High-Tech Park, Fuyuanyi Road 156, HePing Community, FuHai Street , BaoAn-Zone, ShenZhen ,GuangDong,China Phone: 708-571-3148 13823787280 Email: [email protected] [email protected]

Confidentiality Request Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section ß552(b)(4) of the Freedom of Information Act, we request confidentiality for the documentation of the following products: FCC ID Model name 2BP9F-W8 W8, W9, W10, W11, W12, W15, W16, W18, W20 For the products listed above, we request permanent confidentiality for all applicable exhibits as there are: • the Operational Description • the Block Diagram • the Schematics • the Parts Lists • the Tune Up Information The above listed exhibits contain trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact us at the address shown below. Sincerely, Jun.12,2025 Signature Date Printed Name of Signee: Shi bojiang Company: Shenzhen Boerx Electronics Co.，Ltd. Address: 401， building 10, High-Tech Park, Fuyuanyi Road 156, HePing Community, FuHai Street , BaoAn-Zone, ShenZhen ,GuangDong,China Phone: 13823787280 Fax: Email: [email protected]

Finnovate Group,LLC 124 E Cliff St Suite C1 Solana Beach, CA 92075 USA Declaration Letter Date: Jun.17,2025 To: Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: For our business issue and marketing requirement, we would like to list differe nt model number on the FCC certificates and reports , as following: FCC ID: 2BP9F-W8 Model Number:W8, W9, W10, W11, W12, W15, W16, W18, W20 Model Difference: The only difference between the models is the color of appearance. Sincerely, Name / Title Shi bojiang/Manager Company Name Shenzhen Boerx Electronics Co.，Ltd. Company Address 401， building 10, High-Tech Park, Fuyuanyi Road 156, HePing Community, FuHai Street , BaoAn-Zone, ShenZhen ,GuangDong,China Tel: 13823787280 Fax: Email: Shen [email protected]

(Company Name) (Company Address) Declaration Date: Jun.12,2025 FCC ID: 2BP9F-W8 Model Number: W8, W9, W10, W11, W12, W15, W16, W18, W20 To: Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, Shenzhen Boerx Electronics Co.，Ltd. declare that this EUT (FCC ID: 2BP9F-W8) doesn’t have Ad Hoc mode function on “non-US/Canada frequencies”. In addition. The frequency selection feature is disabled by firmware for devices marked to the US/Canada. For DTS part of this device, only channels 1-11 will be used in North America, Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Name / Title Shi bojiang Company Name Shenzhen Boerx Electronics Co.，Ltd. Company Address 401， building 10, High-Tech Park, Fuyuanyi Road 156, HePing Community, FuHai Street , BaoAn-Zone, ShenZhen ,GuangDong,China Tel: 13823787280 Fax: Email: [email protected]

External Photographs FCC ID: 2BP9F-W8

Label Sample for FCC ID: 2BP9F-W8 FCC ID: 2BP9F-W8 Size for the label: 3mm X 6mm Product Name : HOME USE VISUAL EAR PICK Model : W8 FCC ID :2BP9F-W8

Internal photographs FCC ID: 2BP9F-W8 Antenna

MAXLAB Testing Co., Ltd. Report No.: MAX250550504501MPE Report No.: MAX250550504501MPE Page 1 of 6 MPE FCC Part 15C Measurement and Test Report For Shenzhen Boerx Electronics Co.，Ltd. FCC ID: 2BP9F-W8 FCC Rule(s): FCC Part 15.247 Product Description: HOME USE VISUAL EAR PICK Tested Model: W8 Report No.: MAX250550504501MPE Tested Date: May. 10~Jun.10, 2025 Issued Date: Jun. 10, 2025 Tested By: Lris Yao / Engineer Reviewed By: Levi Xiao / EMC Manager Approved & Authorized By: Salon Ouyang / PSQ Manager Prepared By: MAXLAB Testing Co., Ltd. 1/F, Building B, Xinshidai GR Park, Shiyan Street, Bao'an District, Shenzhen, ShiyanStreet, Bao'an District, Shenzhen,Guangdong,518052,People’s Republic of China Tel: 400-882-9628 Fax: 86- 755-26508703 MAXLAB Testing Co., Ltd. Report No.: MAX250550504501MPE Report No.: MAX250550504501MPE Page 2 of 6 MPE 1. GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) Client Information Applicant: Shenzhen Boerx Electronics Co.，Ltd. Address of applicant: 401， building 10, High-Tech Park, Fuyuanyi Road 156, HePing Community, FuHai Street , BaoAn-Zone, ShenZhen ,GuangDon g,China Manufacturer: Shenzhen Boerx Electronics Co.，Ltd. Address of manufacturer: 401， building 10, High-Tech Park, Fuyuanyi Road 156, HePing Community, FuHai Street , BaoAn-Zone, ShenZhen ,GuangDon g,China General Description of EUT Product Name: HOME USE VISUAL EAR PICK Brand Name: N/A Models No.: W8, W9, W10, W11, W12, W15, W16, W18, W20（The only difference between the models is the color of appearance） Rated Voltage: DC 3.7V by battery Note: The test data is gathered from a productio.0n sample provided by the manufacturer. Technical Characteristics of EUT Support Standards: 802.11b, 802.11g, 802.11n Frequency Range: 2412-2462MHz Modulation: CCK, OFDM, QPSK, BPSK, 16QAM, 64QAM Quantity of Channels: 11 for 802.11b/g/n Channel Separation: 5MHz Type of Antenna: PCB Antenna Antenna Gain: 0.5dBi MAXLAB Testing Co., Ltd. Report No.: MAX250550504501MPE Report No.: MAX250550504501MPE Page 3 of 6 MPE 1.2 Test Standards The tests were performed according to following standards: ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB 447498 D01 General RF Exposure Guidance v06: Mobile and Portable Device, RF Exposure, Equipment Authorization Procedures. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1091: Radiofrequency radiation exposure evaluation: mobile devices 1.3 Test Facility MAXLAB Testing Co., Ltd. 1/F, Building B, Xinshidai GR Park, Shiyan Street, Bao'an District, Shenzhen, ShiyanStreet, Bao'an District, Shenzhen,Guangdong,518052,People’s Republic of China FCC Test Firm Registration Number: 562200 Designation Number: CN1338 Tel: 400-882-9628 Fax: 86-755-26508703 1.4 Measurement Uncertainty Measurement uncertainty Parameter Conditions Uncertainty RF Output Power Conducted ±0.42dB MAXLAB Testing Co., Ltd. Report No.: MAX250550504501MPE Report No.: MAX250550504501MPE Page 4 of 6 MPE 2. TEST LIMIT 2.1 Requirement According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions. The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1) To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion.When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.” [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. When one of the following test exclusion conditions is satisfied for all combinations of simultaneous transmission configurations, further equipment approval is not required to incorporate transmitter modules in host devices that operate in the mixed mobile and portable host platform exposure conditions. The grantee is re…

Text truncated - open the document above for the full version.

add ：东莞市凤岗镇塘村沥红石桥新华工业区2栋3楼 电话： 0769-87840035 传真： 0769-87840035 规 格 承 认 书 SPECIFICATION FOR APPROVAL 编 号： 17050301 File No. 版 本： 1.0 Revision 客 戶 CUSTOMER: ______________________________________ 客 戶 料 号 CUSTOMER NO: ______________________________________ 品 名 2.4GHz 板载 PCB Antenna PART NAME: ______________________________________ 供 方 料 号 SUPPLIER NO: _____________________________________ 送样日期 Date: 送样数量 Q’TY: PCS 客户确认 CUSTOMER APPROVED BY APPROVAL CHIEF SUPERVISOR 供方确认 SUPPLIER SIGNATURE APPROVAL CHECK DESIGN SH-RD-F04-A Shenzhen Boerx Electronics Co.，Ltd. Manufacturer: Shenzhen Boerx Electronics Co.，Ltd. Address of manufacturer: 401， building 10, High-Tech Park, Fuyuanyi Road 156, HePing Community, FuHai Street , BaoAn-Zone, ShenZhen ,GuangDong,China add ：东莞市凤岗镇塘村沥红石桥新华工业区2栋3楼 电话： 0769-87840035 传真： 0769-87840035 承认书项目表 NO. 内 容 （ Contents ） 页 数 （ Number of Page ） 页 码 （ Page Code ） 1 承认书封面 （ Spec Cover ） 11 2 承认书项目表（ Spec Item ） 12 3 工程成品图 （ Drawing ） 13 4 电性测试报告（ Test Reports ） 14 5 S 参数测试 （ S Parameter ） 15 6 增益测试 （ Gain Test ） 16 7 8 9 10--- 11--- 12 --- add ：东莞市凤岗镇塘村沥红石桥新华工业区2栋3楼 电话： 0769-87840035 传真： 0769-87840035 add ：东莞市凤岗镇塘村沥红石桥新华工业区2栋3楼 电话： 0769-87840035 传真： 0769-87840035 Electrical Properties Frequency 2.4GHz Impedance 50 0hm Nominal V.S.W.R1.92 : 1 Max Return Loss -10 dB Max Radiation Omni-directional Gain (Peak) 0.5dBi Cable Loss 3.2 dB / m Max @ 2450 MHz Polarization Linear, Vertical Admitted Power 0.5 W ConnectorNone Physical Properties Antenna MaterialPCB Cable Type Operating Temp.-10 ~ +60 ̊C Storage Temp.-10 ~ +70 ̊C Cable Color 电 性 测 试 报 告 Test Reports add ：东莞市凤岗镇塘村沥红石桥新华工业区2栋3楼 电话： 0769-87840035 传真： 0769-87840035 S 参 数 测 试 S Parameter Test AgilentE5071C add ：东莞市凤岗镇塘村沥红石桥新华工业区2栋3楼 电话： 0769-87840035 传真： 0769-87840035 增 益 测 试 Gain Test Antenna Radiation Pattern VS Gain 0 45 90 135 180 225 270 315 -5 -5 -15 -15 -25 -25 -35 -35-45

MAXLAB TESTING CO., LTD. Report No.: MAX250550504501RF Report No.: MAX250550504501RF Page 1 of 47 FCC Part 15.247 FCC Part 15C Measurement and Test Report For Shenzhen Boerx Electronics Co.，Ltd. FCC ID:2BP9F-W8 FCC Rule(s): FCC Part 15C Product Description: HOME USE VISUAL EAR PICK Tested Model: W8 Report No.: MAX250550504501RF Tested Date: May. 10~Jun.10, 2025 Issued Date: Jun. 10, 2025 Tested By: Lris Yao/ Engineer Reviewed By: Levi Xiao / EMC Manager Approved & Authorized By: Salon Ouyang / PSQ Manager Prepared By: MAXLAB TESTING CO., LTD. 1/F, Building B, Xinshidai GR Park, Shiyan Street, Bao'an District, Shenzhen,Guangdong,518052,People’s Republic of China Tel: 400-882-9628 Fax: 86- 755-26508703 MAXLAB TESTING CO., LTD. Report No.: MAX250550504501RF Report No.: MAX250550504501RF Page 2 of 47 FCC Part 15.247 TABLE OF CONTENTS 1. GENERAL INFORMATION ...................................................................................................................................... 3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .................................................................................. 3 1.2 TEST STANDARDS ...................................................................................................................................................... 4 1.3 TEST METHODOLOGY ................................................................................................................................................ 4 1.4 TEST FACILITY .......................................................................................................................................................... 4 1.5 EUT SETUP AND TEST MODE .................................................................................................................................... 5 1.6 MEASUREMENT UNCERTAINTY ................................................................................................................................. 5 1.7 TEST EQUIPMENT LIST AND DETAILS ........................................................................................................................ 6 2. SUMMARY OF TEST RESULTS .............................................................................................................................. 7 3. RF EXPOSURE ............................................................................................................................................................ 8 3.1 STANDARD APPLICABLE ............................................................................................................................................ 8 3.2 TEST RESULT............................................................................................................................................................. 8 4. ANTENNA REQUIREMENT ..................................................................................................................................... 9 4.1 STANDARD APPLICABLE ............................................................................................................................................ 9 4.2 EVALUATION INFORMATION ..................................................................................................................................... 9 5. POWER SPECTRAL DENSITY .............................................................................................................................. 10 5.1 STANDARD APPLICABLE .......................................................................................................................................... 10 5.2 TEST PROCEDURE .................................................................................................................................................... 10 5.3 ENVIRONMENTAL CONDITIONS ............................................................................................................................... 10 5.4 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................... 11 6. 6DB BANDWIDTH .................................................................................................................................................... 18 6.1 STANDARD APPLICABLE .......................................................................................................................................... 18 6.2 TEST PROCEDURE .................................................................................................................................................... 18 6.3 ENVIRONMENTAL CONDITIONS ............................................................................................................................... 18 6.4 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................... 18 7. RF OUTPUT POWER ............................................................................................................................................... 25 7.1 STANDARD APPLICABLE .......................................................................................................................................... 25 7.2 TEST PROCEDURE .................................................................................................................................................... 25 7.3 ENVIRONMENTAL CONDITIONS ............................................................................................................................... 25 7.4 SUMMARY OF TEST RESULTS/PLOTS ....................................................................................................................... 26 8. FIELD STRENGTH OF SPURIOUS EMISSIONS ................................................................................................ 26 8.1 STANDARD APPLICABLE ...................................................................................…

Text truncated - open the document above for the full version.

Test Setup Photos FCC ID: 2BP9F-W8