2BPZX-FO01SBAGFind My & Find Hub Luggage Locator

Before you start access via Wi-Fi or cellular service. • Locate the button on the front side of the Luggage Locator as shown below. • Before you begin, ensure Bluetooth is enabled on your Android or iOS device, and that the device has internet TM FONVOI Luggage Locator supports Apple Find My and Google’s Find Hub, allowing you to track your luggage and check its status during travel. It securely attaches to suitcases and helps you quickly locate your bag at airport baggage claim. The tag also includes a slot for a name and contact card, making identification and recovery easier if your luggage is misplaced. During initial setup, you can select your preferred network. However, the finder cannot operate on both networks simultaneously. Once a network is selected, the other is automatically disabled. To switch networks, you must perform a factory reset on the finder. Instructions 1.Enable the finder: Press the button once. A confirmation beep will sound. Get started with an iOS device • Place your finder next to your iOS device and press the button once to activate it. If activation is successful, you will hear a beep. • On your iOS device, open the Find My app. Tap the Items tab, then tap Add Item. Select Other Supported Item. (If you’ve previously added items, tap the “+” button first, then choose Add Other Item.) • Once the Find My app detects your finder, follow the on-screen instructions to add it to the Find My app. Get started with an Android device • Place your finder near your Android device (Make sure your Android device is awake and unlocked) and press the button once to activate it. If activation is successful, you will hear a beep. • Wait for a half-screen notification to appear, then follow the on-screen instructions on your Android device to add the finder to Find Hub app. Locate your finder and valuables • After adding the finder to Apple’s Find My or Find Hub app, attach it to your valuables. You can then use the corresponding app to locate both the finder and the item it’s attached to. 2.Disable the finder 1) Quickly press the button twice. A confirmation beep will sound. 2) Press and hold the button for five seconds. A beep will sound. 3) Release the button. Two confirmation beeps will sound. 3.Factory reset 1) Quickly press the button twice. A confirmation beep will sound. 2) Immediately after you hear the confirmation sound, press and hold the button. After holding it for 5 seconds, the device will begin emitting a single beep sound once per second, for a total of five beep sounds. 3) Continue holding the button, and release it immediately after you hear a double beep sound. If the operation is successful, the device will beep four times. After resetting, you can link the Carbon Finder to a different Google or Apple account. However, if you want to link it to a new Apple account, you must also remove it from its previous Apple account on your iOS device. Locate your finder when it’s nearby 1) Open the Apple Find My app or Find Hub app, then tap your Luggage Locator from the item/device list. 2) Tap “Play Sound” to make your finder beep. 3) Once you've located it, stop the beeping by either using the app or pressing the button once on the finder. Locate your finder when it’s faraway 1) Open the Apple Find My app or Find Hub app, then tap your Luggage Locator from the item/device list. 2) The current location of your finder will appear on the map, along with a timestamp showing when it was last located. Caution The button on the Luggage Locator is a physical mechanical button, not touch-sensitive. A light tap will not trigger any action, please press it firmly with your fingertip. When pressed correctly, the finder will emit confirmation sounds (as described in the subsequent sections) and you will see the LED flash. If you don’t hear the sound or see the LED flash, the button may not have been pressed properly. It is intentionally designed to prevent accidental activation or unintended operation, so it may feel unfamiliar at first. Don’t hesitate to apply a bit of force when pressing it. Compatibility, Legal and Credit Line Enabling “Notify when left Behind”(only available on Apple Find My) 1) Open the Apple Find My app and select your Luggage Locator from the list. 2) Under Notifications, enable the Notify When Left Behind option. 3) You’ll receive a notification if you leave your finder behind and it goes out of the Bluetooth range of your iOS device. Enabling “Notify when Found”(only available on Apple Find My) 1) Open the Apple Find My app and select your Luggage Locator from the list. 2) Under Notifications, turn on the Notify When Found toggle. 3) You’ll receive a notification with the location when your Luggage Locator is detected by another device on the Apple Find My network. Note: “Notify When Found” can only be activated when your finder is out of the Bluetooth range of your iOS device. Enabling “Mark as lost”if your Luggage Locator is lost(only available on Find Hub) 1) Open the Find Hub app and select your Luggage Locator from the list. 2) Tap Mark as lost and follow the on-screen instructions to fill the contact information. 3) You will be notified if the Find Hub network locates your lost Luggage Locator. Specification Model FO01SBAGBK Bluetooth version 5.4 Dimensions 102*68*5.2mm (4.02*2.68*0.21inches) Weight48g (1.69oz) Charging type Wireless charging iOS 14.5, macOS 10.15 or above Android 9 or above Bary Type FONVOI Luggage Locator Model: FO01SBAGBK User Manual SAFETY WARNING WARNING FRAGILE Do not charge the battery out of recommended temperature range of 10 C and 45 C. Waste lithium batteries shall not be discarded at will. Please dispose of them according to local laws and regulations. Luggage Locator supports wireless charging. To charge the device, simply place it on a compatible wireless charger. A small circular indicator light on the device will show the charging status: Red light — Charging in progress Green light — Fully charged The charging a…

Text truncated - open the document above for the full version.

1/1 USAgentforServiceofProcessLETTEROFATTESTATION TO: OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USAgentforServiceofProcess: CompanyName:HOPEKCORPORATIONINC Address:16755CoyoteBushDrUnit84,SanDiego,CA92127UnitedStates FRN:0034562900 ContactName:YangyangXu TelephoneNo:561-875-9826 E-mail:[email protected] ThisletteristoconfirmthattheUSAgentforServiceofProcessacceptsresponsibilitytoactas alocalrepresentativeonbehalfofShenzhenJintongtaiPlasticElectronicsCo.,Ltd. TheUSAgentforServiceofProcessisawareofandagreestocomplywiththerequirements outlinedintheFCCEquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause §2.911. Applicant: CompanyName:ShenzhenJintongtaiPlasticElectronicsCo.,Ltd. ProductDescription:FindMy&FindHubLuggageLocator FRN:0037128543 GranteeCode:2BPZX FCCID:2BPZX-FO01SBAG ContactName:GuijinCai Address:2ndFloor,Building5,TongfuyuXufaScienceandTechnologyPark,Shangcun, GongmingStreet,GuangmingDistrict,Shenzhen TelephoneNo:13713956636 E-mail:[email protected] TheApplicantisawareofandagreestocomplywiththerequirementsoutlinedintheFCC EquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause§2.911. ThisAgreementisvaliduntil(Permanentlyvalid). Date:2026/2/26 Applicant’sName: ShenzhenJintongtaiPlasticElectronicsCo., Ltd. USAgentforServiceofProcess’sName: HOPEKCORPORATIONINC Title:GeneralmanagerTitle:Manager SignatureSignature

Rev 1/26/2023 Shenzhen Jintongtai Plastic Electronics Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Feb. 03, 2026 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2BPZX-FO01SBAG [Shenzhen Jintongtai Plastic Electronics Co., Ltd.] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [Shenzhen Jintongtai Plastic Electronics Co., Ltd.] certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, (Applicant signature) (Applicant printed name) Guijin Cai Rev 1/26/2023 Shenzhen Jintongtai Plastic Electronics Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Feb. 03, 2026 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2BPZX-FO01SBAG [Shenzhen Jintongtai Plastic Electronics Co., Ltd.] certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Guijin Cai

DX=25.869mm,DY=6.209mm, D=26.604mm customer name： Jintongtai project name： FONVOILuggageLocator MCU： IN610-Q32-R-G4C0I Debugging Date: 20260106 NO.: Material specification and size Match parameter values name of material Material brand 1 0402 22NH chip inductor 2 0402 3PF chip resistor Murata 3 0402NC chip capacitor ANT PCB Antenna PCB Debugging Result Picture Fre.(MHz)240224402480 S11(dB)-17.46-32.37-18.14 Frequency Gain(dBi) Overall machine picture Shenzhen Xiteng Technology Co., Ltd. No. 3A, 18, Min Tai Building, 241 Min Zhi Avenue, Min Xin Community, Min Zhi Street, Long Hua District, Shenzhen City

Effective Date: April 2, 2020 QSF 7.6.4-8 – Agent Authorization Letter Template Page 1 of 1 Revision Date: Revision: 0 Shenzhen Jintongtai Plastic Electronics Co., Ltd. Date: Feb. 03, 2026 Product Model Number: FONVOI Luggage Locator, FO01SBAGBK, FO01SBAGBL, FO01SBAGBR, FO01SBAGOR, FO01ABAGBK, FO01ABAGBL, FO01ABAGBR, FO01ABAGOR, FO01GBAGBK, FO01GBAGBL, FO01GBAGBR, FO01GBAGOR FCC ID: 2BPZX-FO01SBAG To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:  Testing  Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. By: Contact Listed on FCC Wesbite Title: General manager Email: [email protected] Telephone: 13713956636 On behalf of: Shenzhen Jintongtai Plastic Electronics Co., Ltd.

Shenzhen Jintongtai Plastic Electronics Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February 3, 2026 Subject; Request for Confidentiality FCC ID: 2BPZX-FO01SBAG To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Guijin Cai Title: General manager

Shenzhen Jintongtai Plastic Electronics Co., Ltd. Family models declaration letter Feb. 03, 2026 We Shenzhen Jintongtai Plastic Electronics Co., Ltd. Of 2nd Floor, Building 5, Tongfuyu Xufa Science and Technology Park, Shangcun, Gongming Street, Guangming District, Shenzhen Declare under our sole responsibility that the product FCC ID: 2BPZX-FO01SBAG Product: Find My & Find Hub Luggage Locator Model Number: FONVOI Luggage Locator, FO01SBAGBK, FO01SBAGBL, FO01SBAGBR, FO01SBAGOR, FO01ABAGBK, FO01ABAGBL, FO01ABAGBR, FO01ABAGOR, FO01GBAGBK, FO01GBAGBL, FO01GBAGBR, FO01GBAGOR All the models are the same circuit and module, except the colour and model No.. Guijin Cai/ General manager E-mail : [email protected] Phone : 13713956636 Fax : 13713956636 Address : 2nd Floor, Building 5, Tongfuyu Xufa Science and Technology Park, Shangcun, Gongming Street, Guangming District, Shenzhen

Ext Photos Model: FONVOI Luggage Locator Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6

Int Photos Model: FONVOI Luggage Locator Photo 1 Photo 2 Photo 3 Photo 4 WPT ANT Photo 5 Photo 6 Photo 7 Photo 8 BLE ANT Photo 9

- Page 1 of 9 - Report No.: HB20260129007E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com RF EXPOSURE Test Report Product: Find My & Find Hub Luggage Locator Trade Mark: FONVOI Model Number: FONVOI Luggage Locator FCC ID: 2BPZX-FO01SBAG Prepared for Shenzhen Jintongtai Plastic Electronics Co., Ltd. 2nd Floor, Building 5, Tongfuyu Xufa Science and Technology Park, Shangcun, Gongming Street, Guangming District, Shenzhen Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 9 - Report No.: HB20260129007E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ..................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 5 1.4 ANCILLARY EQUIPMENT .............................................................................................................................................. 5 2 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 6 2.1 TEST LABORATORY ..................................................................................................................................................... 6 2.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 6 2.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 6 2.4 TEST SOFTWARE ........................................................................................................................................................ 6 3 LIST OF TEST EQUIPMENT .................................................................................................................................. 7 4 RF EXPOSURE..................................................................................................................................................... 8 4.1 STANDALONE SAR TEST EXCLUSION CONSIDERATIONS........................................................................................................ 8 4.1.1. Limit ............................................................................................................................................................ 8 4.1.2. Test Procedures ........................................................................................................................................... 8 4.1.3. Test Result ................................................................................................................................................... 9 - Page 3 of 9 - Report No.: HB20260129007E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : Shenzhen Jintongtai Plastic Electronics Co., Ltd. Address ................................. : 2nd Floor, Building 5, Tongfuyu Xufa Science and Technology Park, Shangcun, Gongming Street, Guangming District, Shenzhen Manufacturer's Name .......... : Shenzhen Jintongtai Plastic Electronics Co., Ltd. Address ................................. : 2nd Floor, Building 5, Tongfuyu Xufa Science and Technology Park, Shangcun, Gongming Street, Guangming District, Shenzhen Product description Product name ........................ : Find My & Find Hub Luggage Locator Model Number ....................... : FONVOI Luggage Locator Standards ............................. : FCC CFR 47 PART 1 , 1.1310 Test procedure ....................... : KDB 447498 D01 General RF Exposure Guidance v06 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co., Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ........................................... : Date (s) of performance of tests ............. : Jan. 29, 2026~Feb. 02, 2026 Test Result .............................................. : Pass Testing Engineer : ( Z o e Su) Technical Manager : ( G a r y Lu) Authorized Signatory : (L e o S u) - Page 4 of 9 - Report No.: HB20260129007E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Revision History Revised No. Date of Issue Description 01 Feb. 02, 2026 Original - Page 5 of 9 - Report No.: HB20260129007E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Commun…

Text truncated - open the document above for the full version.

- Page 1 of 53 - Report No.: HB20260129007E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Test Report Product: Find My & Find Hub Luggage Locator Trade Mark: FONVOI Model Number: FONVOI Luggage Locator FCC ID: 2BPZX-FO01SBAG Prepared for Shenzhen Jintongtai Plastic Electronics Co., Ltd. 2nd Floor, Building 5, Tongfuyu Xufa Science and Technology Park, Shangcun, Gongming Street, Guangming District, Shenzhen Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 53 - Report No.: HB20260129007E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ..................................................................................................................................... 6 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 6 1.2 TEST MODE .............................................................................................................................................................. 6 1.3 OPERATION CHANNEL LIST ........................................................................................................................................... 7 1.4 TEST SETUP .............................................................................................................................................................. 7 1.5 POWER SETTING CONFIGURATION PARAMETERS ............................................................................................................... 7 1.6 ANCILLARY EQUIPMENT .............................................................................................................................................. 7 2 SUMMARY OF TEST RESULT ............................................................................................................................... 8 3 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 9 3.1 TEST LABORATORY ..................................................................................................................................................... 9 3.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 9 3.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 9 3.4 TEST SOFTWARE ...................................................................................................................................................... 10 4 LIST OF TEST EQUIPMENT .................................................................................................................................11 5 TEST ITEM AND RESULTS ...................................................................................................................................13 5.1 ANTENNA REQUIREMENT .......................................................................................................................................... 13 5.1.1 Standard Requirement ............................................................................................................................. 13 5.1.2 Test Result ................................................................................................................................................. 13 5.2 CONDUCTED EMISSION ............................................................................................................................................. 14 5.2.1 Limits ................................ ........................................................................................................................ 14 5.2.2 Test Procedures ......................................................................................................................................... 14 5.2.3 Test Setup .................................................................................................................................................. 15 5.2.4 Test Result ................................................................................................................................................. 15 5.3 RADIATED EMISSION ................................................................................................................................................ 18 5.3.1 Limits ........................................................................................................................................................ 18 5.3.2 Test Procedures ......................................................................................................................................... 18 5.3.3 Test Setup .................................................................................................................................................. 18 5.3.4 Test Result ................................................................................................................................................. 19 5.3.5 Band Edge - Radiated ............................................................................................................................... 23 5.3.6 Spurious emission in band 1000MHz-25000MHz ....…

Text truncated - open the document above for the full version.

Photographs of the Test Setup Model: FONVOI Luggage Locator Radiated Emission Below 1GHz Radiated Emission Above 1GHz Conducted Emission