2BQXTT300Two Way Radio

GMRS FCC Warning Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Compliance with RF Exposure Standards WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. FCC Regulatory Conformance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference including received interference that may cause undesired operation. The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. Replacement of any transmitter component (crystal, semiconductor, etc) not authorized by the FCC equipment authorization for this radio could violate FCC rules. This radio complies with IEEE and ICNIRP exposure limits for general population/uncontrolled RF exposure environment at operating duty cycle of up to 50% and is authorized by the FCC for general population/uncontrolled use only. An appropriate warning label is affixed to all units. In order to comply with RF exposure requirements, a minimum distance of 25mm must be maintained when held-to-face, and Back Touch operations are restricted to the approved original accessories (belt clip),a minimum distance of 0 cm. Do not use this device when antenna shows obvious damages.

2.911 (d)(7)USA Agent v1.2 Section 2.911(d)(7) USA Agent for Service of Process Company name: Quanzhou UNIKOO Electronic Technology Co., Ltd. Address: B1604, Building2, Xiamei Jiayuan Xiamei Town, Nan'an City, Quanzhou, Fujian CHINA FCC ID: 2BQXTT300 Date: Feb. 28, 2026 2.911(d)(7) USA Designated Agent for Service of Process We, [Quanzhou UNIKOO Electronic Technology Co., Ltd.] (“the applicant”) designate [Wedo Group] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We Acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We Acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Company name: Wedo Group Address: 710 Arabian Ln Walnut, CA 91789, United States FRN：0037730611 Contact Name: Jeffrey Chen Telephone No: (323) 528-1888 Email: [email protected] Applicant Company name: Quanzhou UNIKOO Electronic Technology Co., Ltd. Address: B1604, Building2, Xiamei Jiayuan Xiamei Town, Nan'an City, Quanzhou, Fujian CHINA FRN: 0037297124 Contact Name: WANG JINXING Telephone No: +86-15905012190 Email: [email protected] Signature: Signature:

Quanzhou UNIKOO Electronic Technology Co., Ltd. B1604, Building2, Xiamei Jiayuan Xiamei Town, Nan'an City, Quanzhou, Fujian CHINA Attestation Statements Not Covered Entity Applicant & Not Covered Equipment To: Federal Communications Commission Date: Feb. 28, 2026 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(i) & (ii) FCC ID: 2BQXTT300 FRN: 0037297124 Quanzhou UNIKOO Electronic Technology Co., Ltd. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List, established pursuant to § 1.50002 of reference chapter, as an entity producing “covered” communication equipment. The equipment for which authorization is sought is not “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List that prohibited from receiving an equipment authorization pursuant to section § 2.903 of the FCC rules. Sincerely yours, Applicant Signature: Printed Name: WANG JINXING Title: CEO

Quanzhou UNIKOO Electronic Technology Co., Ltd. B1604, Building2, Xiamei Jiayuan Xiamei Town, Nan'an City, Quanzhou, Fujian CHINA 1 | P a g e Attestation Statements To: Federal Communications Commission Date: Feb. 28, 2026 7435 Oakland Mills Road, Columbia, MD 21046, USA Subject: Attestation of Compliance with FCC Covered List Software Requirements FCC ID: 2BQXTT300 Product Name: Two Way Radio This letter serves as an attestation that the equipment identified above ☐ is / ☒ is not (select one) "covered" software as defined under the Federal Communications Commission (FCC) Covered List requirements, as outlined in FCC 22-84 and KDB 986446. Specifically, the undersigned certifies that the equipment for which authorization is sought: 1. Does not contain cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors, assignees, parents, subsidiaries, affiliates, or any entity that has rebranded or relabeled software produced by the aforementioned entities. 2. Does not have the capability to store, run, or deliver any software identified on the FCC Covered List, including but not limited to cybersecurity and anti-virus software. To support this attestation, the appendix evaluation documentation has been prepared and is included in the certification filing. This attestation is based on a thorough evaluation of the device's design, functionality, and software environment. The undersigned affirms that the information provided is accurate and complete to the best of their knowledge. Sincerely yours, Applicant Signature: Printed Name: WANG JINXING Title: CEO Quanzhou UNIKOO Electronic Technology Co., Ltd. B1604, Building2, Xiamei Jiayuan Xiamei Town, Nan'an City, Quanzhou, Fujian CHINA 2 | P a g e Evaluation regarding to the Covered List Software: Compliance Methodology Evaluation Process Results Device is Inherent compliance ☒ The Chipset(s) used is limited to run the Cybersecurity or anti-virus software. Compliance ☐ The Memory used is limited to run the Cybersecurity or anti-virus software. Compliance ☐ There is storage capacity limitation for store or install the Cybersecurity or anti-virus software. Compliance ☐ Operating system used is limited to run, install or deliver the Cybersecurity or anti-virus software. Compliance Device is not Inherent compliance ☐ Evaluation Based on Software Bill of Materials (SBoM) See attached “SBoM“ Note:The SBoM content is limited to the scope of covered list software (e.g. antivirus and cybersecurity software). ☐ Evaluation Based on Scan for Software on the device ☐ Evaluation Based on Filesystem scan ☐ Evaluation Based on Running software check SBOM (Software Bill of Materials) [For Device is not Inherent compliance] Section Component Name Version Supplier 1 / / / 2 / / / 3 / / /

Quanzhou UNIKOO Electronic Technology Co., Ltd. B1604, Building2, Xiamei Jiayuan Xiamei Town, Nan'an City, Quanzhou, Fujian CHINA Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Feb. 28, 2026 Subject; Request for Confidentiality FCC ID: 2BQXTT300 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Parts List Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: WANG JINXING Title: CEO

Quanzhou UNIKOO Electronic Technology Co., Ltd. B1604, Building2, Xiamei Jiayuan Xiamei Town, Nan'an City, Quanzhou, Fujian CHINA Feb. 28, 2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization for FCC ID: 2BQXTT300 I, the undersigned, hereby authorize (Attestation of Global Compliance (Shenzhen) Co., Ltd) to act on our behalf in all matters relating to this application for equipment certification. Any act carried out by (Attestation of Global Compliance (Shenzhen) Co., Ltd) shall have the same effect as our own and I acknowledge that all responsibility for complying with the terms and conditions of certification, as specified by DERYCOM CERTIFICATION SERVICES, INC., still resides with Quanzhou UNIKOO Electronic Technology Co., Ltd.. We certify that we are not subject to a denial of federal benefits that includes FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862, and that no party to the application, as defined in 47 CFR §1.2002(b), is subject to a denial of federal benefits that includes FCC benefits pursuant to that section. Sincerely, Full name of contact person listed on FCC’s website: WANG JINXING Title: CEO Tel: +8615905012190 Email: [email protected]

Quanzhou UNIKOO Electronic Technology Co., Ltd. B1604, Building2, Xiamei Jiayuan Xiamei Town, Nan'an City, Quanzhou, Fujian CHINA Feb. 28, 2026 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Explanation of differences between product types FCC ID: 2BQXTT300 Models: UK300, UK310, UK320, UK330, UK340, UK350, UK360, UK370, UK380, UK390, UK388, S490, S480, S470, S460, S450, S440, S430, S420, S410, S400, S408, TK260, TK270, TK280, TK290, TK200, TK210, TK220, TK230, TK240, TK250, TK258, FT-41, FT-42, FT-43, FT-44, FT-45, FT-46, FT-47, FT-48, FT-49, FT-50, FT-51, MX200, MX210, MX220, MX230, MX240, MX250, MX260, MX270, MX280, MX290, MX300, BC390, BC380, BC370, BC360, BC350, BC340, BC330, BC320, BC310, BC300, BC388, SK30, SK31, SK32, SK33, SK34, SK35, SK36, SK37, SK38, SK39, SK40, RC3100, RC3200, RC3300, RC3400, RC3500, RC3600, RC3700, RC3800, RC3900, RC4000, RC4100, C2100, C2200, C2300, C2400, C2500, C2600, C2700, C2800, C2900, C2960, C2980, VC405, VC415, VC425, VC435, VC445, VC465, VC475, VC485, VC495, VC488, VC466 To Whom It May Concern: We, The Quanzhou UNIKOO Electronic Technology Co., Ltd. hereby declare that the model : UK300 is identical with the model : UK310, UK320, UK330, UK340, UK350, UK360, UK370, UK380, UK390, UK388, S490, S480, S470, S460, S450, S440, S430, S420, S410, S400, S408, TK260, TK270, TK280, TK290, TK200, TK210, TK220, TK230, TK240, TK250, TK258, FT-41, FT-42, FT-43, FT-44, FT-45, FT-46, FT-47, FT-48, FT-49, FT-50, FT-51, MX200, MX210, Quanzhou UNIKOO Electronic Technology Co., Ltd. B1604, Building2, Xiamei Jiayuan Xiamei Town, Nan'an City, Quanzhou, Fujian CHINA MX220, MX230, MX240, MX250, MX260, MX270, MX280, MX290, MX300, BC390, BC380, BC370, BC360, BC350, BC340, BC330, BC320, BC310, BC300, BC388, SK30, SK31, SK32, SK33, SK34, SK35, SK36, SK37, SK38, SK39, SK40, RC3100, RC3200, RC3300, RC3400, RC3500, RC3600, RC3700, RC3800, RC3900, RC4000, RC4100, C2100, C2200, C2300, C2400, C2500, C2600, C2700, C2800, C2900, C2960, C2980, VC405, VC415, VC425, VC435, VC445, VC465, VC475, VC485, VC495, VC488, VC466, except for the case design and model name. Sincerely, Quanzhou UNIKOO Electronic Technology Co., Ltd. Signature: [WANG JINXING, CEO]

Report No.: AGC17061251204AP02 Page 1 of 5 EXTERNAL PHOTOS All View of EUT Top View of EUT UHF Antenna Report No.: AGC17061251204AP02 Page 2 of 5 Bottom View of EUT Front View of EUT Report No.: AGC17061251204AP02 Page 3 of 5 Back View of EUT Left View of EUT Report No.: AGC17061251204AP02 Page 4 of 5 Right View of EUT Port View-1 of EUT Report No.: AGC17061251204AP02 Page 5 of 5 Port View-2 of EUT Port View-3 of EUT ****************************************End of Report*************************************

FCC ID Label Location 20mm*30mm FCC ID: 2BQXTT300

Report No.: AGC17061251204AP02 Page 1 of 6 INTERNAL PHOTOS Open View-1 of EUT Open View-2 of EUT Report No.: AGC17061251204AP02 Page 2 of 6 Internal View-1 of EUT Internal View-2 of EUT BT Antenna Report No.: AGC17061251204AP02 Page 3 of 6 Internal View-3 of EUT Internal View-4 of EUT Report No.: AGC17061251204AP02 Page 4 of 6 Internal View-5 of EUT Internal View-6 of EUT Report No.: AGC17061251204AP02 Page 5 of 6 Internal View-7 of EUT Internal View-8 of EUT Report No.: AGC17061251204AP02 Page 6 of 6 Internal View-9 of EUT Battery of EUT ****************************************End of Report*************************************

Page 1 of 46 SAR Test Report Report No.: AGC17061251204FH01 FCC ID : 2BQXTT300 PRODUCT DESIGNATION : Two Way Radio BRAND NAME : N/A MODEL NAME : See page 7 APPLICANT : Quanzhou UNIKOO Electronic Technology Co., Ltd. DATE OF ISSUE : Mar. 09, 2026 STANDARD(S) : IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2019 REPORT VERSION : V1.0 Attestation of Global Compliance(Shenzhen) Co., Ltd. Report No.: AGC17061251204FH01 Page 2 of 46 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Mar. 09, 2026 Valid Initial Release Report No.: AGC17061251204FH01 Page 3 of 46 Test Report Applicant Name Quanzhou UNIKOO Electronic Technology Co., Ltd. Applicant Address B1604, Building2, Xiamei Jiayuan Xiamei Town, Nan'an City, Quanzhou, Fujian CHINA Manufacturer Name Quanzhou UNIKOO Electronic Technology Co., Ltd. Manufacturer Address B1604, Building2, Xiamei Jiayuan Xiamei Town, Nan'an City, Quanzhou, Fujian CHINA Factory Name Quanzhou UNIKOO Electronic Technology Co., Ltd. Factory Address B1604, Building2, Xiamei Jiayuan Xiamei Town, Nan'an City, Quanzhou, Fujian CHINA Product Designation Two Way Radio Brand Name N/A Test Model See page 7 Series Model See page 7 Declaration of Difference See page 7 EUT Voltage DC 3.7V Applicable Standard IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2019 Date of receipt of test item Dec. 19, 2025 Test Date Jan. 20, 2026 Report Template AGCRT- US -PTT/SAR (2021-04-20) Note: The results of testing in this report apply to the product/system which was tested only. Prepared By Bibo Zhang (Project Engineer) Mar. 09, 2026 Reviewed By Jack Gui (Reviewer) Mar. 09, 2026 Approved By Angela Li (Authorized Officer) Mar. 09, 2026 Report No.: AGC17061251204FH01 Page 4 of 46 TABLE OF CONTENTS 1. SUMMARY OF MAXIMUM SAR VALUE ......................................................................................................... 5 2. GENERAL INFORMATION ............................................................................................................................... 6 2.1. EUT DESCRIPTION......................................................................................................................................... 6 3. SAR MEASUREMENT SYSTEM ........................................................................................................................ 8 3.1. THE DASY5 SYSTEM USED FOR PERFORMING COMPLIANCE TESTS CONSISTS OF FOLLOWING ITEMS .................... 8 3.2. DASY5 E-FIELD PROBE ................................................................................................................................. 9 3.3. DATA ACQUISITION ELECTRONICS DESCRIPTION ............................................................................................... 9 3.4. ROBOT ........................................................................................................................................................ 10 3.5. LIGHT BEAM UNIT ........................................................................................................................................ 10 3.6. DEVICE HOLDER .......................................................................................................................................... 11 3.7. MEASUREMENT SERVER ............................................................................................................................... 11 3.8. PHANTOM ................................................................................................................................................. 12 4. SAR MEASUREMENT PROCEDURE ............................................................................................................ 13 4.1. SPECIFIC ABSORPTION RATE (SAR) .............................................................................................................. 13 4.2. SAR MEASUREMENT PROCEDURE ................................................................................................................ 14 5. TISSUE SIMULATING LIQUID ....................................................................................................................... 16 5.1. THE COMPOSITION OF THE TISSUE SIMULATING LIQUID..................................................................................... 16 5.2. TISSUE DIELECTRIC PARAMETERS FOR HEAD AND BODY PHANTOMS ............................................................... 16 5.3. TISSUE CALIBRATION RESULT ....................................................................................................................... 17 6. SAR SYSTEM CHECK PROCEDURE ........................................................................................................... 18 6.1. SAR SYSTEM CHECK PROCEDURES ............................................................................................................. 18 6.2. SAR SYSTEM CHECK ................................................................................................................................... 19 7. EUT TEST POSITION ...................................................................................................................................... 20 7.1. BODY WORN POSITION ................................................................................................................................ 20 8. SAR EXPOSURE LIMITS ............................................................................................................................... 21 9. TEST FACILITY .............................................................................................................................................. 22 10. TEST EQUIPMENT LIST .............................................................................................................................. 23 11. MEASUREMENT UNCERTAINTY ................................................................................................................ 24 12. POWER…

Text truncated - open the document above for the full version.

ṩ䙊䙊ؑᢰᵟᴹ䲀ޜਨ *HQWRQJ&RPPXQLFDWLRQ7HFKQRORJ\&R/WG ൠ൰⋹ᐎᐲইᆹഭᇦབྷᆖ、ᆖഝ鬯ᔪ࠶ഝгਧᾬӄቲˈ⭥䈍˖ ཙ㓯㿴ṬҖ 亩ⴞ਽〠%7 ཙ㓯㊫ර˖ᶯ䖭ཙ㓯 ⡸ᵜ˖5$ Պㆮḿ ⹄ਁ 㔃ᶴ˖ ᢩ߶˖ ሴ仁˖ ᇒᡧഎㆮ Antenna Specifications Model: BT2.4 Type: PCBA Version :R:A ADD:National University Science and Technology Park, Daxiamei Town, Quanzhou, Fujian Province 5F, Building 7, Fujian Branch Park Product specification Quick Reference Date Antenna module on the system board Frequenc Range 2400 ~ 2500MHz Ant. Port Input Pwr. (dBm) 0 (Typ. BT class 2 output power) Tot. Rad. Pwr. (dBm) -1.2 (Input pwr – loss pwr) Peak EIRP(dBm) 1.2 Directivity (dBi) 1 (all direction antenna) Efficiency (dB) 6 0.2 % Gain (dBi) 1.68 (Avg Gain XZ-plane) Maximum Power (dBm) 1.7 (XY-plane) Minimum Power (dBm) -4(XY-plane) Avg. Power (dBm) -0.5(XY-plane) Input Impendence(ohm) 50 Polarization Type V ertical & Horizontal V . S .W . R < 1.4 All the technical data and information contained herein are subject to change without prior notice Antenna Layout & module on the system board Antenna Gain Gain Table Unit in dBi @2.44GHz XY-plane XZ-plane YZ-plane Efficiency Peak Avg. Peak Avg. Peak Avg. Module Board 1.35 -0.5 1.68 -3.8 3 1.11 -2.99 6 0.2 % Retum Loss The Environment of Antenna Radiation Pattem 3D radiation pattern diagram XY-plane XZ-plane YZ-plane

Page 1 of 71 FCCTestReport ReportNo.:AGC17061251204FR01 FCCID: 2BQXTT300 APPLICATIONPURPOSE: OriginalEquipment PRODUCTDESIGNATION:TwoWayRadio BRANDNAME:N/A MODELNAME:Seepage6. APPLICANT:QuanzhouUNIKOOElectronicTechnologyCo.,Ltd. DATEOFISSUE:Feb.28,2026 STANDARD(S):FCCPart15SubpartC§15.247 REPORTVERSION:V1.0 AttestationOfGlobalCompliance(Shenzhen)Co.,Ltd ReportNo.:AGC17061251204FR01 Page2of71 ReportReviseRecord ReportVersionReviseTimeIssuedDateValidVersionNotes V1.0/Feb.28,2026ValidInitialRelease ReportNo.:AGC17061251204FR01 Page3of71 TableofContents 1.GeneralInformation..........................................................................................................................................5 2.ProductInformation..........................................................................................................................................6 2.1ProductTechnicalDescription....................................................................................................................6 2.2TestFrequencyList.....................................................................................................................................7 2.3RelatedSubmittal(S)/Grant(S).................................................................................................................8 2.4TestMethodology........................................................................................................................................8 2.5SpecialAccessories....................................................................................................................................8 2.6EquipmentModifications.............................................................................................................................8 2.7AntennaRequirement.................................................................................................................................8 3.TestEnvironment..............................................................................................................................................9 3.1AddressoftheTestLaboratory...................................................................................................................9 3.2TestFacility..................................................................................................................................................9 3.3EnvironmentalConditions.........................................................................................................................10 3.4MeasurementUncertainty........................................................................................................................10 3.5ListofEquipmentUse...............................................................................................................................11 4.SystemTestConfiguration.............................................................................................................................13 4.1EUTConfiguration....................................................................................................................................13 4.2EUTExercise............................................................................................................................................13 4.3ConfigurationofTestedSystem................................................................................................................13 4.4EquipmentUsedInTestedSystem..........................................................................................................14 4.5SummaryofTestResults..........................................................................................................................15 5.DescriptionofTestModes.............................................................................................................................16 6.DutyCycleMeasurement...............................................................................................................................18 7.RFOutputPowerMeasurement....................................................................................................................19 7.1ProvisionsApplicable................................................................................................................................19 7.2MeasurementProcedure..........................................................................................................................19 7.3MeasurementSetup(BlockDiagramofConfiguration)...........................................................................19 7.4MeasurementResult.................................................................................................................................20 8.6dBBandwidthMeasurement.......................................................................................................................24 8.1ProvisionsApplicable................................................................................................................................24 8.2MeasurementProcedure..........................................................................................................................24 8.3MeasurementSetup(BlockDiagramofConfiguration)...........................................................................24 8.4MeasurementResults...............................................................................................................................25 9.PowerSpectralDensityMeasurement.........................................................................................................32 9.1ProvisionsApplicable................................................................................................................................32 9.2MeasurementProcedure..........................................................................................................................32 9.3MeasurementSetup(BlockDiagramofConfiguration…

Text truncated - open the document above for the full version.

ReportNo.:AGC17061251204FR01 Page43of71 Test_Graph_LE2M_ANT1_2402_2Mbps_LowerBandEmissions Test_Graph_LE2M_ANT1_2402_2Mbps_HigherBandEmissions ReportNo.:AGC17061251204FR01 Page44of71 Test_Graph_LE2M_ANT1_2440_2Mbps_ReferenceLevel Test_Graph_LE2M_ANT1_2440_2Mbps_LowerBandEmissions ReportNo.:AGC17061251204FR01 Page45of71 Test_Graph_LE2M_ANT1_2440_2Mbps_HigherBandEmissions Test_Graph_LE2M_ANT1_2480_2Mbps_ReferenceLevel ReportNo.:AGC17061251204FR01 Page46of71 Test_Graph_LE2M_ANT1_2480_2Mbps_LowerBandEmissions Test_Graph_LE2M_ANT1_2480_2Mbps_HigherBandEmissions ReportNo.:AGC17061251204FR01 Page47of71 TestGraphsofBandEdgeEmissionsinNon-RestrictedFrequencyBands Test_Graph_LE1M_ANT1_2402_1Mbps_LowerBandEdgeEmissions Test_Graph_LE1M_ANT1_2480_1Mbps_HigherBandEdgeEmissions ReportNo.:AGC17061251204FR01 Page48of71 Test_Graph_LE2M_ANT1_2402_2Mbps_LowerBandEdgeEmissions Test_Graph_LE2M_ANT1_2480_2Mbps_HigherBandEdgeEmissions ReportNo.:AGC17061251204FR01 Page49of71 11.RadiatedSpuriousEmission 11.1MeasurementLimit  FCCPart15.209Limitinthebelowtabletobefollowed Frequencies (MHz) FieldStrength (microvolts/meter) MeasurementDistance (meters) 0.009~0.4902400/F(kHz)300 0.490~1.70524000/F(kHz)30 1.705~30.03030 30~881003 88~2161503 216~9602003 Above9605003 Note:Allmodesweretestedforrestrictedbandradiatedemission,thetestrecordsreportedbelowaretheworst resultcomparedtoothermodes. 11.2MeasurementProcedure 1.TheEUTwasplacedonthetopoftheturntable0.8or1.5meteraboveground.Thephasecenterofthe receivingantennamountedonthetopofaheight-variableantennatowerwasplaced3metersfaraway fromtheturntable. 2.PowerontheEUTandallthesupportingunits.Theturntablewasrotatedby360degreestodeterminethe positi…

Text truncated - open the document above for the full version.