2BROM-HC0100Halo connect

HomeAware Sensor Product Information HomeAware Sensor Product Description The HomeAware Sensor captures layer 2 data from WIFI and Bluetooth devices (BLE) and transmits filtered data to the cloud for classification and presence detection. The cloud notifies a user of changes via mobile app notifications and makes current and historical state information available via secure APIs to both users and third-party monitoring services. The HomeAware Sensor consists of two system-on-chips (SoCs), each containing a single 2.4GHz multi-protocol radio. SoC-1 supports 2.4GHz 802.11 b/g/n Wi-Fi and Bluetooth Low Energy 5 (BLE). SoC-2 supports Bluetooth Low Energy v4.2. The HomeAware Sensor operates in one of three modes: onboarding, device pairing, and normal sensing. In onboarding mode, only SoC #1 is active. Using BLE, the sensor connects to the user’s mobile device for the secure transmission of the home WIFI network SSID and password. While remaining connected to BLE, the radio attempts to connect to the home WIFI network. Upon successful WIFI connection, and communication with the cloud, the BLE link is dropped. In device pairing mode, SoC #2 uses BLE 4.2 to advertise so that a mobile phone can pair with it. SoC #1 uses WIFI to communicate pairing status to the cloud. In normal sensing mode, SoC #1 uses WIFI for sensing WIFI devices as well as communicating with the cloud. SoC #2 uses BLE for sensing Bluetooth devices and send to SOC #1. There are two LEDs on the front of the unit • Single color BLUE LED – on in onboard mode only • Bi-color GREEN / RED LED - indicates cloud connection over WIFI status o Blinking green - attempting to connect o Solid green - connected o Solid red - error, unable to connect There is one button on the right side of the unit • Short press puts sensor into onboard mode • Long press after power-on causes factory reset Specification Entity Name - HomeAware Model Name – Halo Connect Model Number – HC0100 Power Source – 100-120VAC 60Hz Max 6W Connectivity – WIFI 2.4GHz 802.11b/g/n & BLE 5 (SOC #1) + BLE 4.2 (SOC #2) Operation Temperature – 0 to 50 ºC Wall-mount Installation Height – 15 to 48 inches Dimensions (approximate) - 62mm W x 62mm H x 26mm D (not including AC blades) User Manual FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This devic e may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Thes e limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used i n accordance with the instructions, may caus e harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outl et on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. IC Caution:： This device complies with Innovation, Science, and Economic Development Canad licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d' Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. FCC/IC Radiation Exposure Statement: This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. L'appareil est conforme aux limites d'exposition aux rayonnements spécifiées par la FCC/ISED pour les environnements non contrôlés. La distance entre le radiateur et le corps doit être d'au moins 20 cm lors de l'installation et du fonctionnement de l'appareil.

Ubiety Technologies, Inc 213 W Institute Pl, Chicago, IL 60610 US Tel: +1 (212) 300 7693 Email: [email protected] Date: 2026-02-02 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir/Madam, Our product Halo connect, Model: HC0100; FCC ID 2BROM-HC0100. For use in USA, this product only support BLE 1M, 2.4G WiFi: 2412-2462MHz (802.11b/g/n20 mode). The other functions has been shielded by the manufacturer using the software, the end user has no capability to activate it. Sincerely Yours, Signature: Contact person: Jing Chen Title: Chief of Staff

Ubiety Technologies, Inc 213 W Institute Pl, Chicago, IL 60610 US Tel: +1 (212) 300 7693 Email: [email protected] Date: 2026-02-02 Attestation Letter FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 § 2.911(d)(5)(i) Filing FCC ID: 2BROM-HC0100 Ubiety Technologies, Inc certifies that the equipment for which authorization is sought, is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely Yours, Signature: Print Name: Jing Chen Title: Chief of Staff CFR 47 §2.911(d)(5)(i) Attestation Letter

Ubiety Technologies, Inc 213 W Institute Pl, Chicago, IL 60610 US Tel: +1 (212) 300 7693 Email: [email protected] Attestation Letter Date:2026-02-02 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 § 2.911(d)(5)(ii) Filing FCC ID: 2BROM-HC0100 Ubiety Technologies, Inc certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. We also certify that, as of the date of the filing of the application, the equipment does not utilize cyber- security or anti-virus software from Kaspersky Lab, Inc, or any of its successors and assignees, which is also on the “covered list”. Sincerely Yours, Signature: Print Name: Jing Chen Title: Chief of Staff CFR 47 §2.911 (d)(5)(ii) Attestation Letter

U.S. AGENT LETTER OF ATTESTATION Date: 2026-02-02 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2BROM-HC0100 Ubiety Technologies, Inc certifies that, as of the date of the filing of the application, Ubiety Technologies, Inc is our designated U.S. agent for service of process for the above referenced FCC ID. Ubiety Technologies, Inc accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Ubiety Technologies, Inc accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent and Applicant Information: Name: Ubiety Technologies, Inc Address: 213 W Institute Pl, Chicago, IL 60610 US FRN: 0037396553 Tel.: +1 (212) 300 7693 Email: [email protected] Signed by (printed name): Jing Chen Signature:

Ubiety Technologies, Inc 213 W Institute Pl, Chicago, IL 60610 US Tel: +1 (212) 300 7693 Email: [email protected] Date: 2026-02-02 FCC Authorization FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We Ubiety Technologies, Inc the undersigned, hereby authorizes Shenzhen Accurate Technology Co., Ltd. to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Shenzhen Accurate Technology Co., Ltd. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Printed Name: Jing Chen Title: Chief of Staff

Ubiety Technologies, Inc 213 W Institute Pl, Chicago, IL 60610 US Tel: +1 (212) 300 7693 Email: [email protected] Date: 2026-02-02 FCC Authorization FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2BROM-HC0100 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Ubiety Technologies, Inc hereby requests long-term confidential treatment of information accompanying this application as outlined below: • Block Diagram • Schematics • Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature: Printed Name: Jing Chen Title: Chief of Staff

Shenzhen Accurate Technology Co., Ltd. No.: 2504X07651E-RF EUT External Photos External Photos Page 1 / 3 External Photos Shenzhen Accurate Technology Co., Ltd. No.: 2504X07651E-RF EUT External Photos External Photos Page 2 / 3 Shenzhen Accurate Technology Co., Ltd. No.: 2504X07651E-RF EUT External Photos External Photos Page 3 / 3 ***** END *****

Label Location The label is located on the bottom of the product (on the same side as the plug).

Shenzhen Accurate Technology Co., Ltd. No.: 2504X07651E-RF EUT Internal Photos Internal Photos Page 1 / 4 Internal Photos Shenzhen Accurate Technology Co., Ltd. No.: 2504X07651E-RF EUT Internal Photos Internal Photos Page 2 / 4 Shenzhen Accurate Technology Co., Ltd. No.: 2504X07651E-RF EUT Internal Photos Internal Photos Page 3 / 4 ANT1 BLE Shenzhen Accurate Technology Co., Ltd. No.: 2504X07651E-RF EUT Internal Photos Internal Photos Page 4 / 4 ANT0 BLE & 2.4G WiFi ***** END *****

Note: This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA, or any agency of the Federal Government. The information marked “#” is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included but no need marked. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. Shenzhen Accurate Technology Co., Ltd. Floor 1, KuMaKe Building, Dongzhou Community, Guangming Street, Guangming District, Shenzhen, Guangdong, China. Tel: +86 755-26503290 Web: www.atc-lab.com Rev:A/4.0(2024/11/01) Page 1 of 6 TR-4-E-R052 TEST REPORT Applicant Name: Ubiety Technologies, Inc Address: 213 W Institute Pl, Chicago, IL 60610 US Report Number: 2504X07651E-RF-00C FCC ID: 2BROM-HC0100 Test Standard (s) FCC PART 2.1091 Sample Description Product Name: Halo connect Model No.: HC0100 Trade Mark: N/A Date Received: 2025-09-12 Report Date: 2026-02-28 Test Result: The EUT complied with the standards above. Prepared and Checked By: Approved By: Amanda Wei Bob Liao EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: 2504X07651E-RF-00C Rev:A/4.0(2024/11/01) Page 2 of 6 TR-4-E-R052 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ................................................................................................................ 3 GENERAL INFORMATION ............................................................................................................................ 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ........................................................................ 4 OBJECTIVE ................................................................................................................................................... 4 TEST FACILITY .............................................................................................................................................. 4 RF EXPOSURE .............................................................................................................................................. 5 APPLICABLE STANDARD ................................................................................................................................. 5 RESULT ........................................................................................................................................................ 5 EXHIBIT A-EUT PHOTOGRAPHS ................................................................................................................ 6 Shenzhen Accurate Technology Co., Ltd. Report No.: 2504X07651E-RF-00C Rev:A/4.0(2024/11/01) Page 3 of 6 TR-4-E-R052 DOCUMENT REVISION HISTORY Revision Number Report Number Description of Revision Date of Revision Rev.00 2504X07651E-RF-00C Original Report 2026-02-28 Shenzhen Accurate Technology Co., Ltd. Report No.: 2504X07651E-RF-00C Rev:A/4.0(2024/11/01) Page 4 of 6 TR-4-E-R052 GENERAL INFORMATION Product Description for Equipment under Test (EUT) Product Name Halo connect Tested Model HC0100 Voltage Range # AC 120V/60Hz Max 6W Frequency Range BLE 1M: 2402-2480MHz 2.4G Wi-Fi: 2412-2462MHz Maximum Conducted Output Power(Peak) (actual test result) BLE ANT0: 7.51dBm, BLE ANT1:5.76dBm 2.4G WiFi: 22.7dBm Antenna Specification # PCB Antenna BLE: ANT0: 2.72 dBi, ANT1:2.6dBi 2.4G WiFi: ANT0: 2.72 dBi (It is provided by the applicant.) Sample Serial Number 39XJ-2 (Assigned by ATC, Shenzhen) Sample/EUT Status Good condition Objective This test report is in accordance with Part 2-Subpart J, Part 15-Subparts C and Part 2-Subpart J, Radiofrequency Radiation Exposure of the Federal Communication Commission rules. The tests were performed in order to determine compliance with FCC §2.1091 rules. Test Facility The test site used by Shenzhen Accurate Technology Co., Ltd. to collect test data is located on the Floor 1, KuMaKe Building, Dongzhou Community, Guangming Street, Guangming District, Shenzhen, Guangdong, China. Accredited by American Association for Laboratory Accreditation (A2LA).The Certificate Number is 4297.01. Shenzhen Accurate Technology Co., Ltd. Report No.: 2504X07651E-RF-00C Rev:A/4.0(2024/11/01) Page 5 of 6 TR-4-E-R052 RF EXPOSURE Applicable Standard According to subpart 2.1091 systems operating under the provisions of this section shall be operated in a manner that ensures the public is not exposed to RF energy level in excess of the communication guidelines. Limits for General Population/Uncontrolled Exposure Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (Minutes) 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f 2 ) 30 30-300 27.5 0.073 0.2 30 300-1500 / / f/1500 30 1500-100,000 / / 1.0 30 f = frequency in MHz * = Plane-wave equivalent power density Result Calculated Formulary: Predication of MPE limit at a given distance S = 2 4R PG  S = power density (in appropriate units, e.g. mW/cm 2 ) P = power input to the antenna (in appropriate units, e.g., mW). G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain. R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) Calculated Result: Radio Frequency (MHz) Antenna Gain # Tune up conducted power # Evaluation Distance (cm) Power Density (mW/cm 2 ) MPE Limit (mW/cm 2 ) (dBi) (numeric) (dBm) (mW) BLE ANT0 2402-2480 2.72 1.87 8 6.31 20 0.002 1 BLE ANT1 2402-2480 2.60 1.82 6 3.98 20 0.001 1 2.4G…

Text truncated - open the document above for the full version.

Model Antenna Type Antenna ANT0 BLE & 2.4G WIFI ANT1 BLE Ubiety Technologies, Inc 213 W Institute PI, Chicago, IL 60610 USA 1、Free Space 1、Free Space HC0100-ANT Passive Antenna PCB Antenna Product placement method 2D field pattern diagram S11 X Z Y Efficiency performance Product placement method 2D field pattern diagram S11 X Z Y Efficiency performance ANT1 BLE ANT0 BLE&2.4G WiFI

Note: This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA, or any agency of the Federal Government. The information marked ―#‖ is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included but no need marked. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with ▲.This report must not be used by the client to claim product certification, approval, or endorsement by A2LA, or any agency of the U.S. Government. Each test item follows the test standard(s) without deviation. Shenzhen Accurate Technology Co., Ltd. Floor 1, KuMaKe Building, Dongzhou Community, Guangming Street, Guangming District, Shenzhen, Guangdong, China. Tel: +86 755-26503290 Web: www.atc-lab.com Rev:A/4.1(2025/12/12) Page 1 of 101 TR-4-E-R137 TEST REPORT Applicant Name: Ubiety Technologies, Inc Address: 213 W Institute Pl, Chicago, IL 60610 US Report Number: 2504X07651E-RFB FCC ID: 2BROM-HC0100 IC: 34659-HC0100 Test Standard (s) FCC PART 15.247 RSS-247 ISSUE 4, JULY 24, 2025 RSS-GEN ISSUE 5, FEBRUARY 2021 AMENDMENT 2 Sample Description Product Name: Halo connect Model No.: HC0100 Trade Mark: N/A Date Received: 2025-09-12 Report Date: 2026-02-10 Test Result: The EUT complied with the standards above. Prepared and Checked By: Approved By: Amanda Wei Bob Liao EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: 2504X07651E-RFB Rev:A/4.1(2025/12/12) Page 2 of 101 TR-4-E-R137 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ................................................................................................................ 4 GENERAL INFORMATION ............................................................................................................................ 5 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ........................................................................ 5 OBJECTIVE ................................................................................................................................................... 5 TEST METHODOLOGY .................................................................................................................................... 5 TEST FACILITY .............................................................................................................................................. 6 MEASUREMENT UNCERTAINTY ....................................................................................................................... 6 SYSTEM TEST CONFIGURATION ............................................................................................................... 7 DESCRIPTION OF TEST CONFIGURATION......................................................................................................... 7 EUT EXERCISE SOFTWARE AND POWER LEVEL # ............................................................................................ 7 SPECIAL ACCESSORIES AND EQUIPMENT MODIFICATIONS ............................................................................... 7 SUPPORT EQUIPMENT LIST AND DETAILS ....................................................................................................... 7 EXTERNAL I/O CABLE .................................................................................................................................... 7 BLOCK DIAGRAM OF TEST SETUP .................................................................................................................. 8 SUMMARY OF TEST RESULTS ................................................................................................................. 10 TEST EQUIPMENT LIST ............................................................................................................................. 11 ANTENNA REQUIREMENT......................................................................................................................... 12 APPLICABLE STANDARD ............................................................................................................................... 12 ANTENNA CONNECTOR CONSTRUCTION ....................................................................................................... 12 AC LINE CONDUCTED EMISSIONS .......................................................................................................... 13 APPLICABLE STANDARD ............................................................................................................................... 13 EUT SETUP ................................................................................................................................................ 13 EMI TEST RECEIVER SETUP ........................................................................................................................ 13 TEST PROCEDURE ...................................................................................................................................... 13 CALCULATION ............................................................................................................................................. 14 TEST DATA ................................................................................................................................................. 14 RADIATED SPURIOUS EMISSION ............................................................................................................. 17 APPLICABLE STANDARD ....................…

Text truncated - open the document above for the full version.

Note: This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA, or any agency of the Federal Government. The information marked ―#‖ is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included but no need marked. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with ▲.This report must not be used by the client to claim product certification, approval, or endorsement by A2LA, or any agency of the U.S. Government. Each test item follows the test standard(s) without deviation. Shenzhen Accurate Technology Co., Ltd. Floor 1, KuMaKe Building, Dongzhou Community, Guangming Street, Guangming District, Shenzhen, Guangdong, China. Tel: +86 755-26503290 Web: www.atc-lab.com Rev:A/4.1(2025/12/12) Page 1 of 89 TR-4-E-R136 TEST REPORT Applicant Name: Ubiety Technologies, Inc Address: 213 W Institute Pl, Chicago, IL 60610 US Report Number: 2504X07651E-RFA FCC ID: 2BROM-HC0100 IC: 34659-HC0100 Test Standard (s) FCC PART 15.247 RSS-247 ISSUE 4, JULY 24, 2025 RSS-GEN ISSUE 5, FEBRUARY 2021 AMENDMENT 2 Sample Description Product Name: Halo connect Model No.: HC0100 Trade Mark: N/A Date Received: 2025-09-12 Report Date: 2026-02-28 Test Result: The EUT complied with the standards above. Prepared and Checked By: Approved By: Amanda Wei Bob Liao EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: 2504X07651E-RFA Rev:A/4.1(2025/12/12) Page 2 of 89 TR-4-E-R136 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ................................................................................................................ 4 GENERAL INFORMATION ............................................................................................................................ 5 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ........................................................................ 5 OBJECTIVE ................................................................................................................................................... 5 TEST METHODOLOGY .................................................................................................................................... 5 TEST FACILITY .............................................................................................................................................. 6 MEASUREMENT UNCERTAINTY ....................................................................................................................... 6 SYSTEM TEST CONFIGURATION ............................................................................................................... 7 DESCRIPTION OF TEST CONFIGURATION......................................................................................................... 7 EUT EXERCISE SOFTWARE AND POWER LEVEL # ............................................................................................ 7 SPECIAL ACCESSORIES AND EQUIPMENT MODIFICATIONS ............................................................................... 7 SUPPORT EQUIPMENT LIST AND DETAILS ....................................................................................................... 7 EXTERNAL I/O CABLE .................................................................................................................................... 7 BLOCK DIAGRAM OF TEST SETUP .................................................................................................................. 8 SUMMARY OF TEST RESULTS ................................................................................................................. 10 TEST EQUIPMENT LIST ............................................................................................................................. 11 ANTENNA REQUIREMENT......................................................................................................................... 12 APPLICABLE STANDARD ............................................................................................................................... 12 ANTENNA CONNECTOR CONSTRUCTION ....................................................................................................... 12 AC LINE CONDUCTED EMISSIONS .......................................................................................................... 13 APPLICABLE STANDARD ............................................................................................................................... 13 EUT SETUP ................................................................................................................................................ 13 EMI TEST RECEIVER SETUP ........................................................................................................................ 13 TEST PROCEDURE ...................................................................................................................................... 13 CALCULATION ............................................................................................................................................. 14 TEST DATA ................................................................................................................................................. 14 RADIATED SPURIOUS EMISSIONS .......................................................................................................... 20 APPLICABLE STANDARD ........................…

Text truncated - open the document above for the full version.

Shenzhen Accurate Technology Co., Ltd. No.: 2504X07651E-RF Test Photos Test Photos Page 1 / 4 Photo of Power Line Conducted Emission Measurement Shenzhen Accurate Technology Co., Ltd. No.: 2504X07651E-RF Test Photos Test Photos Page 2 / 4 Radiated Spurious Emissions Test View (9kHz-30MHz) Radiated Spurious Emissions Test View (30MHz- 1GHz) Shenzhen Accurate Technology Co., Ltd. No.: 2504X07…

Text truncated - open the document above for the full version.