2BSBD-ININUM01ININUM Personal Fragrance Device

PERSONAL FRAGRANCE DEVICE User Manual Scan to View User Guide Welcome to the world of ININUM TM , where technology meets fragrance. Thank you for choosing ININUM TM Personal Fragrance Device, the world’s first personal smart fragrance system. To ensure the best experience, please read this manual carefully and follow the setup instructions provided in the ININUM App before using your device for the first time. For additional guidance, inspiration, and updates, please visit: www.ininum.com Enjoy your journey with ININUM™. 1 1. PACKAGE INCLUDES: • ININUM Personal Fragrance Device x1 • USB-C Charging Cable x1 • User Manual x1 2. GETTING TO KNOW ININUM TM PERSONAL FRAGRANCE DEVICE: Nozzle Locking Ring LED Status Indicator ININUM 2 3. GETTING STARTED: 1. Carefully remove the ININUM TM Personal Fragrance Device and all included accessories from the box. 2. Retain the packaging and user manual for future storage or transport if needed. 3. Read the entire user manual carefully before use. 4. Before first use, activate the device by connecting it to power using the supplied USB-C cable and charging it for at least 1.5 hours. POD Cap POD Base Unit Upper Module PODS Compartment Spray Button Charging Port MODE button 4. The orange light will start flashing, indicating the system is preparing (this may take up to 1 minute). 5. When the green light starts flashing, the device is ready for POD insertion. Note: Do not twist the Upper Module itself, only twist the locking ring. 3 1. Make sure the device is powered ON (Hold Mode button). 2. Hold the Base Unit securely and rotate the locking ring to the right to unlock the Upper Module. 4. USING YOUR ININUM™ DEVICE: 4.1 Unlocking the Upper Module: 3. Lift the upper module to access the POD compartment. 4 1. After lifting the upper module, you’ll access the POD compartment. 2. Insert all three PODs into the empty POD compartments in any order. Ensure each POD fits securely in place. 4.2 Installing the PODs: Note: Hold the device horizontally during POD insertion to prevent air from entering the system. 4. Close the upper module and lock it by rotating the locking ring until it clicks into position. 3. Once the PODs are inserted, remove the protective cap from each fragrance POD. 1. Make sure the line on the ring is aligned with the “unlocked” symbol before starting. 4.3 Locking the Upper Module: 5 3. Align the line on the ring with the dot on the device base unit. 6. The device flashes orange during system setup. When complete, the green light flashes three times to confirm readiness. The selected preset fragrance color (Magenta, Yellow, Cyan or White) will appear. 5. Then, hold the Upper Module securely and rotate the locking ring to the left toward the “locked” symbol until it is fully locked onto the Base unit. 4. Once aligned, press the Upper Module down firmly onto the base unit. Note: If the marks are not aligned, the device may not close properly, and POD detection will not start. 2. Insert the Upper Module straight down onto the Base Unit. 6 5. PRIMING: Each time new PODs are inserted into the ININUM device, the system needs to perform a priming flow. This process ensures even distribution of the fragrance through the tubing and nozzle, providing precise and consistent spraying. Priming can be done in two ways: • Automatically via the ININUM App– simply follow the on-screen instructions. Note: • If the device has been used before, there might still be a small amount of the previous fragrance remaining in the tubing. • To maintain scent accuracy, always perform the priming process (3–5 sprays) after inserting new PODs. • Manually– press the “Spray” button 3–5 times until fragrance starts dispensing evenly. 7 Switching the Presets: Your ININUM device stores up to four preset fragrances that can be selected directly, without using the app. • To change the fragrance composition, use the ININUM smartphone app. • Press and hold the “Mode” button to turn the device ON. When the device is on, press the Mode button once to switch between your saved fragrance presets. 6. OPERATING THE DEVICE: Spraying: To dispense the fragrance, press the Spray button once while the device is powered ON. The device will release a fine mist of fragrance through the nozzle. Power On / O ̃: •To turn ON: Press and hold the “Mode” button until the LED ring lights up. •To turn OFF: Press and hold the “Mode” button again until the lights fade out. 8 • Each press changes the LED ring color Magenta, Yellow, Cyan, or White — indicating the active preset. The colors cycle in sequence with each press. Standby Mode: • If the device remains inactive for several minutes, it automatically enters Sleep Mode to save power. •To wake the device: Press the Spray or Mode button once. Tip: When the device wakes from sleep mode, it automatically restores the last selected fragrance preset. 2. Sign in with your existing account or create a new one. 3. Add your device: • To initiate pairing press and hold the “Mode” button for 7 seconds. • Add your device in the app by selecting “Pair Device” or following the on-screen pairing prompt. 4. Follow the on-screen instructions to complete setup. Note: The Smartphone has to meet with the following minimum technical requirements: • iPhone / iOS: minimum iOS 13 or latter. •Android: Android 8+ with Bluetooth 5.0 or higher. 7. APP SETUP INSTRUCTIONS: 1. Download the ININUM Fragrance App on your mobile phone. For downloading, visit: www.ininum.com/app or scan the given QR code: 9 8. CHARGING INSTRUCTIONS: Caution: Do not charge the device in high temperatures or humid environments. 1. Connect the supplied USB-C cable to the charging port on the device. PODS replacement Opening the Upper Module – inserting PODs Orange light flashing while the system prepares. Green light flashing indicates the device is ready to accept the PODs. Inserting the PODs Presets change Press the “Mode” button once Fragrance colour (Magenta, Yellow, Cyan, White) Changing of preset selecte…

Text truncated - open the document above for the full version.

Form: RFT-AMER-TCB-OP-19o Revision: 1 Page 1 of 1 Date: 1/25/2023 M33 d.o.o. Ulica Jozeta Jame 12 1000 Ljubljana Slovenia Attention: Application Examiner Re: Certification designating a U.S. agent for service of process pursuant to section 2.911(d)(7) of the FCC rules To whom it may concern, This letter is to confirm both M33 d.o.o. (“Applicant”) acknowledge consent to obligations of each party pursuant to 47 CFR part §2.911(d)(7) of the FCC rules in regard to the agent for service of process. I Marko Matijevic HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant. I further acknowledge the requirement to maintain an agent extends for no less than one year after the termination of all marketing and importation or the conclusion of and commission-related proceeding involving the equipment and agree to immediately notify the FCC and Intertek if there is any change in the status identified above. Applicant Company Name : M33 d.o.o. Contact Name : Marko Matijevic Address : Ulica Jozeta Jame 12, 1000 Ljubljana, Slovenia Telephone No : +386 31 828 101 Email : [email protected] FCC ID : 2BSBD-ININUM01 Applicant FRN : 0037522653 Signature: ____________________________________ Date: 19.09.2025 I, Tim Payne at FCC US Agent, LLC, HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Agent. I consent to the obligation to accept service of process on behalf of the applicant in regard to the FCC ID designated above. Agent Company Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708-571-3148 Email: [email protected] Signature: ____________________________________ Date: __________10/03/2025____________________

Form: RFT-AMER-TCB-OP-19n Revision: 1 Page 1 of 1 Date: 1/25/2023 M33 d.o.o. Ulica Jozeta Jame 12 1000 Ljubljana Slovenia Attention: Application Examiner Re: Covered List, located at https://www.fcc.gov/supplychain/coveredlist and 47 CFR parts §2.903 and §2.911(d)(5)(ii) of the FCC rules Applicant: M33 d.o.o. FCC ID: [2BSBD- ININUM01] To whom it may concern, M33 d.o.o. (“Applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to 47 CFR part §2.903 of the FCC rules and does not originate directly or indirectly from any company named on the covered list located in the link above or any subsidiary or affiliate thereof. Applicant further certifies that, as of the date of the filing of the application, the Applicant is not identified on the Covered List as an entity producing “covered” equipment and is not a subsidiary or affiliate of any such entity pursuant to 47 CFR part §1.50002 and required by 47 CFR part §2.911(d)(5)(ii) of the FCC rules. Applicant further certifies that no Cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software is installed in the equipment being certified. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the Applicant and agree to immediately notify Intertek if there is any change in the status identified above. Marko Matijevic CEO 19.09.2025 M33 d.o.o.

M33 d.o.o. Ulica Jozeta Jame 12 1000 Ljubljana Slovenia 19.09.2025 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement M33 d.o.o. FCC ID: (2BSBD- ININUM01) To Whom It May Concern: We, M33 d.o.o., hereby authorized Intertek Testing Services Shenzhen Ltd. Guangzhou Branch to act as our Agent for the purpose of preparing application for FCC ID number (2BSBD- ININUM01) under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is (2025-10-8). The Limited Agency Agreement expires on (2026-5-7), unless sooner terminated or extended by written notice to Intertek Testing Services Shenzhen Ltd. Guangzhou Branch and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Marko Matijevic CEO

1(1) M33 d.o.o. Ulica Jozeta Jame 12 1000 Ljubljana Slovenia 19.09.2025 Attention: Application Examiner RE: Request for Confidentiality Applicant:M33 d.o.o. FCC ID: [2BSBD- ININUM01] To Whom It May Concern: Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request is hereby submitted byM33 d.o.o.to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: [Select one or more of items below, as appropriate] • Schematics • Detailed Block Diagrams • Detailed Operational/Functional Description Rationale for request for confidentiality: M33 d.o.o.has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us.] If you have questions or need further information, please contact the undersigned. Sincerely, Marko Matijevic CEO

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room101/301/401/102/202/302/402/502/602/702/802, No. 7-2, Caipin Road, Huangpu District, Guangzhou, Guangdong, China Job No.: 250912123GZU FCC ID: 2BSBD-ININUM01 Version: 08 July 2020 Page 1 of 3 FCC simultaneously transmitter-Portable (SAR exclusion) SAR test exclusion evaluation compliance requirement Model no.: ININUM01 1. KDB 447498 D01 v06 requirement Standalone SAR test exclusion considerations: E (V/m)=(30*P*G) 0.5 /d E=Electric Field (V/m) Remark: E(V/m)=10X (dBUV/m) /20 *10 -6 P=Peak RF output Power (W) G=EUT Antenna numeric gain (numeric) d= Separation distance between radiator and human body (m) in the formula above: d=30m, 1.3 dBuV/m (max described by client) so P= 0.0000041mW The transmission frequencies of the device are below 100 MHz. In KDB 447498 D01 v06: 4.3.1 Standalone SAR test exclusion considerations: Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room101/301/401/102/202/302/402/502/602/702/802, No. 7-2, Caipin Road, Huangpu District, Guangzhou, Guangdong, China Job No.: 250912123GZU FCC ID: 2BSBD-ININUM01 Version: 08 July 2020 Page 2 of 3 FCC simultaneously transmitter-Portable (SAR exclusion) Formulas as below: P ≤ (3 x m)/√f (GHz) a) P is the max. power of channel, including tune-up tolerance, mW m is min.test separation distance, mm f (GHZ) is the RF channel transmit frequency in GHz P≤ (3 x 50)/√ f (GHZ) + (m-50)x f (MHZ) /150 b)1) P≤ [(3x50)/√0.1 + (m-50)x100/150] x [1+lg(100/ f (MHZ) )] c)1) P≤ {[(3x50)/√0.1 + (50-50)x100/150] x (1+lg100/100)} x 1/2 c)2) P ≤ 442.7mW= ½ X 474 x [1+ log (100/13.56)] NFC: The Max Conducted Output Power and SAR Test Exclusion Threshold (mW) are listed below: Transmit frequency (MHz) Max Output Power (mW) SAR Test Exclusion Threshold (mW) 13.56 0.000004 442.7 According to SAR Exclusion Threshold in KDB 447498 (D01) General RF Exposure Guidance v06, the SAR report is not required. The transmission frequencies of the device are between 100 MHz and 6 GHz. The worst case test separation distance is 5mm. The Max Conducted Output Power and SAR Test Exclusion Threshold (mW) are listed below: BLE: Transmit frequency (MHz) Max Conducted Output Power (mW) SAR Test Exclusion Threshold (mW) 2402-2480 0.84 9.5 According to SAR Exclusion Threshold in KDB 447498 (D01) General RF Exposure Guidance v06, the SAR report is not required. Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room101/301/401/102/202/302/402/502/602/702/802, No. 7-2, Caipin Road, Huangpu District, Guangzhou, Guangdong, China Job No.: 250912123GZU FCC ID: 2BSBD-ININUM01 Version: 08 July 2020 Page 3 of 3 FCC simultaneously transmitter-Portable (SAR exclusion) Simultaneous transmission SAR test exclusion considerations: KDB 447498 (D01): When an antenna qualifies for the standalone SAR test exclusion and also transmits simultaneously with other antennas, the standalone SAR value should be estimated according to the following to determine the simultaneous transmission SAR test exclusion: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)]·[√f(GHz)/x] W/kg, for test separation distances ≤ 50 mm; where x = 7.5 for 1-g SAR and x = 18.75 for 10-g SAR. The max. power of NFC is 0.000004 mW, The max. power of Bluetooth is 0.84 mW, min. test separation is 5 mm, x=7.5 for 1-g SAR: The estimated 1-g SAR1 value of NFC is: 0.000000012W/kg The estimated 1-g SAR2 value of Bluetooth is: 0.034716387W/kg The simultaneously transmitting antennas in each operating mode and exposure condition combination must be considered one pair at a time to determine the SAR to peak location separation ratio to qualify for test exclusion. The ratio is determined by (SAR1 + SAR2) 1.5 /Ri, rounded to two decimal digits, and must be ≤ 0.04 for all antenna pairs in the configuration to qualify for 1-g SAR test exclusion. When 10-g SAR applies, the ratio must be ≤ 0.10. SAR1 and SAR2 are the highest reported or estimated SAR values for each antenna in the pair, and Ri is the separation distance in mm between the peak SAR locations for the antenna pair. (SAR1 + SAR2) 1.5 /Ri = (0.000000012+0.034716387) 1.5 /5 = 0.001293695 < 0.04 (Ri = 5mm) According to SAR Exclusion Threshold in KDB 447498 (D01) General RF Exposure Guidance v06, the SAR report is not required. Test Location: Intertek Testing Services Shenzhen Ltd. Guangzhou Branch All tests were performed at: Room102/104, No 203, KeZhu Road, Science City, GETDD Guangzhou, China.

MORLAB ShenzhenMorlabCommunicationsTechnologyCo.,Ltd.,FL.1-3,BuildingA, FeiYangSciencePark,No.8LongChangRoad,Block67,BaoAnDistrict, ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page1of 3 REPORTNo.：SZ25100181E01 AnnexDEUTPhotos 1.Testenvironment MORLAB ShenzhenMorlabCommunicationsTechnologyCo.,Ltd.FL.1-3,BuildingA, FeiYangSciencePark,No.8LongChangRoad,Block67,BaoAnDistrict, ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page2of3 REPORTNo.：SZ25100181E01 2.EUT MORLAB ShenzhenMorlabCommunicationsTechnologyCo.,Ltd.FL.1-3,BuildingA, FeiYangSciencePark,No.8LongChangRoad,Block67,BaoAnDistrict, ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page3of3 REPORTNo.：SZ25100181E01

NOTE:ThisdocumentisissuedbyShenzhenMorlabCommunicationsTechnologyCo.,Ltd.,thetestreportshallnotbereproducedexceptin fullwithoutpriorwrittenpermissionofthecompany.Thetestresultsapplyonlytotheparticularsample(s)testedandtothespecifictestscarried outwhichisavailableonrequestforvalidationandinformationconfirmedatourwebsite. MORLAB ShenzhenMorlabCommunicationsTechnologyCo.,Ltd.,FL.1-3,BuildingA, FeiYangSciencePark,No.8LongChangRoad,Block67,BaoAnDistrict, ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page1of 10 REPORTNo.：SZ25100181E01 TESTREPORT APPLICANT:TeamHonour(HK)LTD. PRODUCTNAME:RTX86022.4GHz&BLEDualModeModule MODELNAME:RTX8608 TRADENAME:N/A BRANDNAME:N/A STANDARD(S):IEEEStd149-2021 RECEIPTDATE:2025-10-17 TESTDATE:2025-10-21 ISSUEDATE:2025-10-23 Editedby: MaoRujie(Rapporteur) Approvedby: ChiShide(Supervisor) MORLAB ShenzhenMorlabCommunicationsTechnologyCo.,Ltd.FL.1-3,BuildingA, FeiYangSciencePark,No.8LongChangRoad,Block67,BaoAnDistrict, ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page2of10 REPORTNo.：SZ25100181E01 DIRECTORY 1.TechnicalInformation ........................................................................................................3 1.1.ApplicantandManufacturerInformation ....................................................................3 1.2.EquipmentUnderTest(EUT)Description ...................................................................3 2.TestResults ........................................................................................................................4 2.1.AppliedReferenceDocuments .....................................................................................4 2.2.TestConditions...............................................................................................................4 2.3.MeasurementUncertainty.............................................................................................4 2.4.TestResultslists.............................................................................................................5 AnnexATestSetupPhotos..................................................................................................6 AnnexBFigures.....................................................................................................................7 1.2DRadiationPattern.........................................................................................................7 2.3DRadiationPattern.........................................................................................................8 AnnexCGeneralInformation .............................................................................................10 1.1IdentificationoftheResponsibleTestingLaboratory ..............................................10 1.2IdentificationoftheResponsibleTestingLocation ..................................................10 1.3TestEquipmentsUtilized ..............................................................................................10 1.4TestSoftwareUtilized ....................................................................................................10 AnnexDEUTPhotos ChangeHistory VersionDateReasonforchange 1.02025-10-23Firstedition MORLAB ShenzhenMorlabCommunicationsTechnologyCo.,Ltd.FL.1-3,BuildingA, FeiYangSciencePark,No.8LongChangRoad,Block67,BaoAnDistrict, ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page3of10 REPORTNo.：SZ25100181E01 1.TechnicalInformation Note:Providebyapplicant. 1.1.ApplicantandManufacturerInformation Applicant: TeamHonour(HK)LTD. ApplicantAddress: Rm1403,Blk4,JinDiKaiXuanPlaza,No.31Longcheng Avenue,NanLianCommunity,LongGangStreet,LonggangDistrict, Shenzhen,Guangdong.China Manufacturer: TeamHonour(HK)LTD. ManufacturerAddress:Rm1403,Blk4,JinDiKaiXuanPlaza,No.31Longcheng Avenue,NanLianCommunity,LongGangStreet,LonggangDistrict, Shenzhen,Guangdong.China 1.2.EquipmentUnderTest(EUT)Description WirelessTypeBluetooth Frequency2400MHz-2500MHz AntennaTypeN/A ProductHWVersionN/A ProductSWVersionN/A IMEIN/A SampleNo.1# MORLAB ShenzhenMorlabCommunicationsTechnologyCo.,Ltd.FL.1-3,BuildingA, FeiYangSciencePark,No.8LongChangRoad,Block67,BaoAnDistrict, ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page4of10 REPORTNo.：SZ25100181E01 2.TestResults 2.1.AppliedReferenceDocuments Leadingreferencedocumentsfortesting: No.IdentityDocumentTitle 1IEEEStd149-2021 IEEERecommendedPracticeforAntenna Measurements Notes:Anyadditions,deviation,orexclusionsfromthemethodshallbenotedinthe"Remark". 2.2.TestConditions TestEnvironmentConditions ： RelativeHumidity(%):25-75 Temperature(°C):10-30 2.3.MeasurementUncertainty Theuncertaintyiscalculatedusingthemethodssuggestedinthe“GuidetotheExpressionof UncertaintyinMeasurement”(GUM)publishedbyISO. MORLAB ShenzhenMorlabCommunicationsTechnologyCo.,Ltd.FL.1-3,BuildingA, FeiYangSciencePark,No.8LongChangRoad,Block67,BaoAnDistrict, ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page5of10 REPORTNo.：SZ25100181E01 2.4.TestResultslists 2.4.1.Gain Frequency (MHz) Gain(dBi) 2400-5.15 2410-5.15 2420-5.31 2430-5.48 2440-5.53 2450-5.58 2460-5.76 2470-5.96 2480-6.11 2490-6.15 2500-6.18 MORLAB ShenzhenMorlabCommunicationsTechnologyCo.,Ltd.FL.1-3,BuildingA, FeiYangSciencePark,No.8LongChangRoad,Block67,BaoAnDistrict, ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page6of10 REPORTNo.：SZ25100181E01 AnnexATestSetupPhotos MORLAB ShenzhenMorlabCommunicationsTechnologyCo.,Ltd.FL.1-3,BuildingA, FeiYangSciencePark,No.8LongChangRoad,Block67,BaoAnDistrict, ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.c…

Text truncated - open the document above for the full version.

M33 d.o.o. TEST REPORT SCOPE OF WORK EMC TESTING–ININUM01 REPORT NUMBER 250912123GZU-001 ISSUE DATE [REVISED DATE] 01-December-2025 [--------------------] PAGES 37 DOCUMENT CONTROL NUMBER FCC BT 4.0 © 2017 INTERTEK TEST REPORT Room101/301/401/102/202/302/ 402/502/602/702/802, No. 7-2, Caipin Road, Huangpu District, Guangzhou, Guangdong, China Telephone: +86 20 8213 9688 Facsimile: +86 20 3205 7538 www.intertek.com.cn This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room101/301/401/102/202/302/402/502/602/702/802, No. 7-2, Caipin Road, Huangpu District, Guangzhou, Guangdong, China Version: 17 August 2025 Page 2 of 37 FCC BT 4.0 Applicant Name & Address : M33 d.o.o. Ulica Jozeta Jame 12, 1000 Ljubljana, Slovenia Manufacturing Site : Kin Yat (Guangdong) AI Co., Ltd. Huang Hua Yuan Industrial District,ShixingCounty,Shaoguan City, Guangdong Province,China Intertek Report No: FCC ID: 250912123GZU-001 2BSBD-ININUM01 Test standards 47 CFR PART 15 Subpart C: 2023 section 15.247 Sample Description Product : ININUM Personal Fragrance Device Model No. : ININUM01 Electrical Rating : DC 5 V ⎓ 1 A, battery 7.4V/500mAH Serial No. : Not Labeled Date Received : 09 September 2025 Date Test Conducted : 01 November 2025-04 November 2025 Prepared and Checked By Elena Lei Project Engineer Approved By: Dean Liu Sr. Project Engineer TEST REPORT Intertek Report No.: 250912123GZU-001 Version: 17 August 2025 Page 3 of 37 FCC BT 4.0 CONTENT TEST REPORT ........................................................................................................................... 1 CONTENT ............................................................................................................................. 3 1.0 TEST RESULT SUMMARY ............................................................................................ 4 2.0 GENERAL DESCRIPTION ............................................................................................. 5 2.1 PRODUCT DESCRIPTION ........................................................................................................ 5 2.2 RELATED SUBMITTAL(S) GRANTS ........................................................................................... 5 2.3 TEST METHODOLOGY .......................................................................................................... 6 2.4 TEST FACILITY ..................................................................................................................... 6 3.0 SYSTEM TEST CONFIGURATION ................................................................................. 6 3.1 JUSTIFICATION .................................................................................................................... 6 3.2 EUT EXERCISING SOFTWARE ................................................................................................. 7 3.3 SPECIAL ACCESSORIES .......................................................................................................... 7 3.4 MEASUREMENT UNCERTAINTY .............................................................................................. 8 3.5 EQUIPMENT MODIFICATION ................................................................................................. 8 3.6 SUPPORT EQUIPMENT LIST AND DESCRIPTION .......................................................................... 8 4.0 MEASUREMENT RESULTS .......................................................................................... 9 4.1 ANTENNA REQUIREMENT ..................................................................................................... 9 4.2 6 DB BANDWIDTH (DTS BANDWIDTH).................................................................................. 10 4.3 MAXIMUM PEAK CONDUCTED OUTPUT POWER ..................................................................... 13 4.4 PEAK POWER SPECTRAL DENSITY ......................................................................................... 16 4.5 OUT OF BAND CONDUCTED EMISSIONS ................................................................................ 19 4.6 RADIATED EMISSIONS ........................................................................................................ 22 4.7 BAND EDGES REQUIREMENT ............................................................................................... 34 4.8 CONDUCTED EMISSION TEST ............................................................................................... 36 5.0 TEST EQUIPMENT LIST ............................................................................................. 37 TEST REPORT Intertek Report No.: 250912123GZU-001 Version: 17 August 2025 Page 4 of 37 FCC BT 4.0 1.0 TEST RESULT SUMMARY Test Item Test Requirement Test Method Result Antenna Requirement FCC PART 15 C section 15.247 (c) and Section 15.203 FCC PART 15 C section 15.247 (c) and Section 15.203 PASS 6 dB Bandwidth (DTS bandwidth) FCC PART 15 C section 15.247 (a)(2) ANSI C63.10: Clause 11.8 PASS Maximum Peak Conducted Output Power FCC PART 15 C section 15.247(b)(3) ANSI C63.10: Clause 11.9.1.1 PAS…

Text truncated - open the document above for the full version.

Radiated Emission (Below 30MHz) Radiated Emission (30MHz-1GHz) Radiated Emission (Above 1GHz) Remark: The EUT is center on the turntable, due to the edge of desk placed on the diameter of the turntable.