2BSIR-701292Lunogrip Charge

LUNOGRIP CHARGE WHAT’S INCLUDED: 1. USB-C to USB-C RTPE Charging Cable 2. Adhesive Metal Ring 3. Sticky Smooth Surface Pad 4. Hex Wrench Product Overview: 1. Wireless Charging Area 2. Suction Cup 3. Loosen & Tighten Knob 4. Height Adjustment Ring 5. USB-C Input Product Specs: Input: 9V-2.22A Output: 15W Instructions: 1. Clean the suction cup thoroughly before use, as dirt may reduce suction strength. 2. Apply to a clean, smooth, flat surface (e.g., glass). Hold the base and twist the knob left to secure until firmly attached. 3. For wooden desks, apply the auxiliary sticker first, then attach the suction cup to ensure adhesion. 4. Adjust the height ring as desired. Place your phone on the charging area. If your phone is not magnetic, attach the metal ring before placing it on the charger. 5. Connect the provided USB-C cable to the input port and plug the other end into a wall charger to begin charging. 6. To remove, hold the base and twist the knob right, then lift the suction tab to release. 7. If the height adjustment ring becomes loose, tighten the screw using the provided hex wrench. Instruction Manual 1 2 3 5 4 FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF Exposure Statement To maintain compliance with FCC'S RF Exposure guidelines, This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

Rev 1/26/2023 BEST Promo USA Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 05-13-2026 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2BSIR-701292 [BEST Promo USA] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [BEST Promo USA] certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, (Applicant signature) (Applicant printed name) Kathy Rasmussen Rev 1/26/2023 BEST Promo USA Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 05-13-2026 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2BSIR-701292 [BEST Promo USA] ce8rtifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Kathy Rasmussen

BEST Promo USA U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: May 13, 2026 Ref: Attestation Statement – Part 2.911(d)(7) filing FCC ID: 2BSIR-701292 BEST Promo USA(“the applicant”) certifies that, as of the date of the filing of the application, BEST Promo USA (“the agent”) is our designated U.S. agent for service of process for the above reference FCC ID. The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission- related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges it is our responsibility to inform the FCC whenever the agent information changes. BEST Promo USA ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name: BEST Promo USA FRN: 0037550241 Address: 201 Clay Road Suite 200 Sunnyvale, Texas 75182 USA Signature: Contact Person: Kathy Rasmussen Tel: 8015929973 Email: [email protected] Applicant Company Name: BEST Promo USA FRN: 0037550241 Address: 201 Clay Road Suite 200 Sunnyvale, Texas 75182 USA Signature: Contact Person: Kathy Rasmussen Tel: 8015929973 Email: [email protected]

BEST Promo USA Date: May 13, 2026 Product Model Number: 701292 FCC ID: 2BSIR-701292 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following: • Testing • Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. Signature: By: Kathy Rasmussen Title: Sr. Product Manager Tel.: 8015929973 Email: [email protected] On behalf of: BEST Promo USA

BEST Promo USA Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: May 14, 2026 Subject; Request for Confidentiality FCC ID: 2BSIR-701292 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: By: Kathy Rasmussen Title: Sr. Product Manager

Report No: DSP26041418-1E FCC ID: 2BSIR-701292 Annex A. EUT External Photos EUT View 1 Model: 701292 EUT View 2 Report No: DSP26041418-1E FCC ID: 2BSIR-701292 EUT View 3 EUT View 4 Report No: DSP26041418-1E FCC ID: 2BSIR-701292 EUT View 5 EUT View 6 Report No: DSP26041418-1E FCC ID: 2BSIR-701292 EUT View 7 EUT View 8

Report No: DSP26041418-1E FCC ID: 2BSIR-701292 Annex D. Label FCC Label Sample Label Size : 20mm*15mm FCC Label Specifications Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Where the EUT is constructed in two or more sections connected by wires and marketed together, the above statement is required to be affixed only to the main control unit. When the EUT is so small or for such use that it is not practicable to place the statement on it, the above information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. FCC Label Location

Report No: DSP26041418-1E FCC ID: 2BSIR-701292 Annex B. EUT Internal Photos EUT View 1 EUT View 2 Coil ANT Report No: DSP26041418-1E FCC ID: 2BSIR-701292 EUT View 3

Report No: DSP26041418-2H FCC Test Report Page 1 of 10 RF Exposure Report FCC ID: 2BSIR-701292 Report No. : DSP26041418-2H Applicant : BEST Promo USA Product Name : Lunogrip Charge Model Name : 701292 Test Standard : FCC CFR 47 PART 1, 1.1310 Date of Issue : 2026-05-06 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.ccuttest.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: DSP26041418-2H FCC Test Report Page 2 of 10 Test Report Basic Information Applicant..................................: BEST Promo USA Address of Applicant...............: 201 Clay Road Suite 200 Sunnyvale, Texas 75182 USA Manufacturer..........................: BEST Promo USA Address of Manufacturer........: 201 Clay Road Suite 200 Sunnyvale, Texas 75182 USA Product Name.........................: Lunogrip Charge Brand Name.............................: - Main Model..............................: 701292 Test Standard..........................: FCC CFR 47 PART 1, 1.1310 KDB 680106 D01 Wireless Power Transfer v04 Date of Test .............................: 2026-04-25 to 2026-05-06 Test Result...............................: PASS Tested By ................................: (Colin Chen) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: DSP26041418-2H FCC Test Report Page 3 of 10 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Test Facilities ........................................................................................................................................................6 1.4 List of Measurement Instruments ..........................................................................................................................7 1.5 Measurement Uncertainty .....................................................................................................................................7 2. RF Exposure .................................................................................................................................................................8 2.1 Standard and Limit................................................................................................................................................8 2.2 Test Procedures ....................................................................................................................................................8 2.3 Test Data and Results ............................................................................................................................................9 Annex A. Test Photos ..................................................................................................................................................... 10 Report No: DSP26041418-2H FCC Test Report Page 4 of 10 Revision History Revision Issue Date Description Revised By V1.0 2026-05-06 Initial Release Lahm Peng Report No: DSP26041418-2H FCC Test Report Page 5 of 10 1. General Information 1.1 Product Information Product Name: Lunogrip Charge Trade Name: - Model Name: 701292 Rated Voltage: USB-C Input: 9V⎓2.22A Wireless Output: 15W Max Test Sample No: DSP26041418-1 Hardware Version: V1.0 Software Version: V1.0 Note 1: The test data is gathered from a production sample, provided by the manufacturer. Wireless Specification Wireless Standard: WPC (QI) Operating Frequency: 110.5-205kHz Modulation: ASK Antenna Gain: 0dBi Type of Antenna: Coil Antenna Type of Device: Portable Device Mobile Device Report No: DSP26041418-2H FCC Test Report Page 6 of 10 1.2 Test Setup Information List of Test Modes Test Mode Description Remark TM1 Wireless charging 15W - TM2 Wireless charging 10W - TM3 Wireless charging 7.5W - TM4 Wireless charging 5W - Note: All modes have been tested and only the worst mode TM1 data is represented in the report. List and Details of Auxiliary Cable Description Length (cm) Shielded/Unshielded With/Without Ferrite - - - - List and Details of Auxiliary Equipment Description Manufacturer Model Serial Number Adapter UGREEN CD289 90324 Phone iPhone iPhone 12pro - 1.3 Test Facilities Laboratory Name: Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China CNAS Laboratory No.: L18863 A2LA Certificate No.: 6983.01 FCC Registration No: 583813 ISED Registration No.: CN0164 Report No: DSP26041418-2H FCC Test Report Page 7 of 10 1.4 List of Measurement Instruments Description Manufacturer Model Serial Number Cal. Date Due. Date Electromagnet-ic radiation tester WAVECONTROL SMP3 23SL0158 2025-07-16 2026-07-15 Electromagnet -ic field probe WAVECONTROL WP400-3 24WP120170 2025-07-16 2026-07-15 Test Software WAVECONTROL SMP N/A N/A N/A 1.5 Measurement Uncertainty Test Item Uncertainty E-field 0.6 dB H-field 0.6 dB Report No: DSP26041418-2H FCC Test Report Page 8 of 10 2. RF Exposure 2.1 Standard and Limit The criteria listed in the following table shall be u…

Text truncated - open the document above for the full version.

FinePage1 of 3 SPECIFICATION FORAPPROVAL 客戶： CUSTOMER: Digiview Technology Limited 客 戶 料 號： CUST P/N: 音泽 料 號： FINE P/N: G43.5*0.8-13.8-0.08*48-12T-7.1UH-L30MM+BJ 産 品 型 號： DESC: Φ 43.5MMX0.8MM 日期： DATE: 2024/09/25 版本： Version: A.0 擬制 PREPARED BY 審核 CHECKED BY 批准 APPROVED BY 客戶承認 CUSTOMERAPPROVE 何立成马莉但可清 东莞市音泽电子科技有限公司 Dongguan Yinzhe Electronic Technology Co., Ltd. 工廠地址：东莞市茶山镇兴韩路（创富中心城）2 栋901 号 Factory Address: Room 901, Building 2, Chuangfu Center City, Xinghan Road, Chashan Town, Dongguan City TEL：18617251159 FinePage2 of 3 VersionChangeHistory 版本 Rev. 變更前 BeforeChange 變更後 After Change 更 改 日 期 ChangeDate 批准 ApprovedBy A.0 new issue ----2024.09.25 But Keqing FinePage3 of 3 SPECIFICATION 産 品 型 號： DESC 】】 G43.5*0.8-13.8-0.08*48-12T-7 .1UH-L30MM+BJ 版本 Rev：A.0 客戶CUST: Precision crafting 客户料号CUST P/N: 一、尺寸DIMENSION:(mm) 二、原理图SCHEMATIC DIAGRAM: A 43.5±0.5 B 38±0.5 C 13.8±0.5 D 30±2 E 3±2 F 5.3±0.2 K 1.65±0.1 J 0.8±0.05 I 三、绕线参数Winding Specification: 序号 NO. 端子 TERMINAL 线径 WIRE 圈数 Turns 绕线方向 Winding Direction 1 S F Hot air line 0.08*48 12TsCCW 四、电气特性ELECTRICAL CHARACTERISTICS: 温度TEMPERATURE:25±10°C,湿度RELATIVE HUMIDITY:65±20% 序号 NO. 项目 ITEM 端子 TERMINAL 标准 SPECIFICATION 测试条件 TEST FREQUENCY 测试仪器 TEST EQUIPMENTS 1IND.S-F 3.9u H ±10%Single coil 100KHz/1.0VLCZ METER 1062B 2IND.S-F7.1uH ±10%Add magnetic chips100KHz/1.0VLCZ METER 1062B 3DCRS-F≤125mΩLCZ METER 502B 擬制 / 日期 PREPARED BY/DATE 審核 / 日期 CHECKED BY/DATE 何立成2024.09.25

Report No: DSP26041418-1E FCC Test Report Page 1 of 23 FCC TEST REPORT FCC ID: 2BSIR-701292 Report No. : DSP26041418-1E Applicant : BEST Promo USA Product Name : Lunogrip Charge Model Name : 701292 Test Standard : FCC Part 15 Subpart C Date of Issue : 2026-05-06 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.ccuttest.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: DSP26041418-1E FCC Test Report Page 2 of 23 Test Report Basic Information Applicant..................................: BEST Promo USA Address of Applicant...............: 201 Clay Road Suite 200 Sunnyvale, Texas 75182 USA Manufacturer..........................: BEST Promo USA Address of Manufacturer........: 201 Clay Road Suite 200 Sunnyvale, Texas 75182 USA Product Name.........................: Lunogrip Charge Brand Name.............................: - Model Name...........................: 701292 Test Standard..........................: FCC Part 15 Subpart C ANSI C63.4-2014 ANSI C63.10-2020 Date of Test .............................: 2026-04-25 to 2026-05-06 Test Result...............................: PASS Tested By ................................: (Colin Chen) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: DSP26041418-1E FCC Test Report Page 3 of 23 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Compliance Standards ...........................................................................................................................................7 1.4 Test Facilities ........................................................................................................................................................7 1.5 List of Measurement Instruments ..........................................................................................................................8 1.6 Measurement Uncertainty .....................................................................................................................................8 2. Summary of Test Results .............................................................................................................................................9 3. Antenna Requirement ............................................................................................................................................... 10 3.1 Standard and Limit.............................................................................................................................................. 10 3.2 Test Result .......................................................................................................................................................... 10 4. Conducted Emissions ................................................................................................................................................ 11 4.1 Standard and Limit.............................................................................................................................................. 11 4.2 Test Procedure.................................................................................................................................................... 11 4.3 Test Data and Results .......................................................................................................................................... 12 5. Radiated Emissions ................................................................................................................................................... 15 5.1 Standard and Limit.............................................................................................................................................. 15 5.2 Test Procedure.................................................................................................................................................... 15 5.3 Test Data and Results .......................................................................................................................................... 17 6. Occupied Bandwidth ................................................................................................................................................. 22 6.1 Standard and Limit.............................................................................................................................................. 22 6.2 Test Procedure.................................................................................................................................................... 22 6.3 Test Data and Results .......................................................................................................................................... 22 Report No: DSP26041418-1E FCC Test Report Page 4 of 23 Revision History Revision Issue Date Description Revised By V1.0 2026-05-06 Initial Release Lahm Peng Report No: DSP26041418-1E FCC Test Report Page 5 of 23 1. General Information 1…

Text truncated - open the document above for the full version.

Report No: DSP26041418-1E FCC ID: 2BSIR-701292 Annex C. Test Photos Conducted Emission Test View 1 Radiated Emission Test View 2 Report No: DSP26041418-1E FCC ID: 2BSIR-701292 Radiated Emission Test View 3