2BSYY-EMHW130627Contactless in-home health monitoring system

User Manual 1 Emerald Innovations Inc. Confidential and Proprietary. 1 HW13 User Manual FCC ID: 2BSYY-EMHW130627 Table of Contents I Introduction & RF Exposure Compliance Statements 2 II Product Overview 3 III Device Installation 3 III.1 Choosing the Deployment Location 3 III.2 Mount the wall Mount on the Chosen Location 3 Figure III-1: Back of Wall Mount with Wall Strips Attached 4 Figure III-2: Front view of Wall Mount 4 III.3 Mounting the Device on the Wall 5 Figure III-3: Device Placement in Wall Mount 5 III.4 Powering on the Device 5 Fig III-4: Device plugged into power 6 IV Connecting Device to Wi-Fi 6 V Uninstallation 6 Fig V-1: Removing wall strip by pulling away from the mount and parallel to the wall 7 VI Certifications and Approvals 7 VII Safety and Maintenance 7 VIII Support and Contact Information 8 User Manual 2 Emerald Innovations Inc. Confidential and Proprietary. 2 I Introduction & RF Exposure Compliance Statements This manual provides an overview of the installation of the Emerald Device. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, this equipment should be installed and operated with a minimum distance of 20 cm (7.9 inches) between the antenna and your body during normal operation. Users must follow the specific operating instructions for satisfying RF exposure compliance. This equipment may only be operated indoors. Operation outdoors is in violation of 47 U.S.C. 301 and could subject the operator to serious legal penalties. User Manual 3 Emerald Innovations Inc. Confidential and Proprietary. 3 II Product Overview The Emerald Device described in this document, model number HW13, is a contactless, in-home health monitoring system that uses low power radio waves to passively measure health metrics without the need for wearables. The HW13 device is designed to be deployed on the wall where it will passively collect health data without any intervention needed by the user. It securely encrypts and uploads data to the cloud via the home’s Wi-Fi network, where Emerald’s powerful AI algorithms extrapolate useful health metrics from the measured signals. Device installation involves physically mounting the device to the wall, connecting it to power, and using the Emerald Mobile App to connect the device to the user’s home Wi-Fi network. III Device Installation III.1 Choosing the Deployment Location The HW13 device location should be chosen to maximize the coverage area and capture activities of interest. The specific room and mounting location within the room to install the device should be chosen to maximize data quality and quantity. III.2 Mount the wall Mount on the Chosen Location III.3.1 Attach Wall Strips to Wall Mount The wall strips have a double-sided adhesive. The blue side has the word “Command”, which should be attached to the wall mount. The black side has the words “WALL side”, which should be attached to the wall. Take the Wall Strips and peel away the blue sided cover in the configuration shown in Figure III-1. Make sure the wall strip tabs hang over the edge so they can be pulled off when the mount is removed. User Manual 4 Emerald Innovations Inc. Confidential and Proprietary. 4 Figure III-1: Back of Wall Mount with Wall Strips Attached III.3.2 Attach Wall Mount to the Wall Peel away the black “This Side Wall” covers of the wall strips and firmly press the wall mount to the wall (Figure III-2). For best contact, pressure should be placed on the wall mount with both hands at the places of the wall strips for 30 seconds. Figure III-2: Front view of Wall Mount The wall mount should be level and placed at the height of the user’s abdomen. User Manual 5 Emerald Innovations Inc. Confidential and Proprietary. 5 III.3 Mounting the Device on the Wall After the wall mount was mounted, place the device on the wall mount. The device is hung by lifting the back of the device above the wall mount and sliding it down such that the slots on the back of the device hang on the hooks of the wall mount. (Figure III-3). Figure III-3: Device Placement in Wall Mount III.4 Powering on the Device Once the device is configured by the remote technician, connect it to power using the provided AC/12VDC power cable. One side of the provided power cable connects to the outlet, and the other to the power jack on the bottom of the case User Manual 6 Emerald Innovations Inc. Confidential and Proprietary. 6 Fig III-4: Device plugged into power The device should stay powered on as the remaining operations are performed. IV Connecting Device to Wi-Fi The device will be connected to the user’s home Wi-Fi network through the Emerald Setup application found in the iOS and Android app stores. Note that the app is used only for Wi-Fi configuration, and does not provide access to any firmware…

Text truncated - open the document above for the full version.

One Broadway St, 14 th Floor Cambridge, MA 02142 Nemko North America, Inc. 303 River Road Ottawa ON K1V 1H2 Canada ATTN.: Reviewing Engineer Subject: Covered Equipment Certification Attestation Letter Applicant: Emerald Innovations, Inc. FCC ID: 2BSYY-EMHW130627 The applicant certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section §2.903 of the FCC rules. This includes certifying that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24- 886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current FCC Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. The applicant certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Signed: Printed name: Rumen Hristov Title: Director of Engineering Company Name: Emerald Innovations, Inc. Date: November 26, 2025

One Broadway St, 14 th Floor Cambridge, MA 02142 Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Appointment of Agent for FCC and ISED Certification Application Dear Director of Certification, This letter formally appoints Spencer Zhong of Nemko Canada, Inc. located at 303 River Road, Ottawa, Ontario, Canada K1V 1H2, as our authorized agent to represent us in the application process for equipment certification. We confirm that the submitted documents accurately depict the device or system seeking certification. Additionally, we guarantee that all units produced, imported, or marketed, as defined by FCC and ISED Canada regulations, will possess a label identical to the one submitted with this application. By signing below, we certify that neither our company nor any party involved in the application is subject to denial of federal benefits, including FCC benefits, as outlined in Section 5301 of the Anti-Drug Abuse Act of 1988 (21 U.S.C. §862) due to a conviction for possession or distribution of a controlled substance. Furthermore, no party involved in the application, as defined in 47 CFR 1.2002 (b), is subject to denial of federal benefits, including FCC benefits. We attest to the truth and accuracy of the information provided to the FCC to the best of our knowledge (47 CFR 2.911 (d)) and acknowledge our responsibilities as a grantee regarding certified equipment (47 CFR 2.909). In instances where our authorized agent signs the application for certification on our behalf, we understand that Nemko North America, Inc. remains solely responsible for adhering to the terms and conditions for certification as specified by Nemko Canada Inc. Sincerely, Dated: November 26, 2025 Agency agreement expiration date: May 1, 2026 *Up to 12 months Signed by: Rumen Hristov Signature Print name Director of Engineering Title 617- 943- 9690 Phone On behalf of: Emerald Innovations, Inc. Company name

1.2. “EMERALD Sensor” shall mean EMERALD’s proprietary devices including hardware, software and firmware, and communication with the rest of the EMERALD Platform. 1.3. “EMERALD Technology” shall mean all of EMERALD Sensor, EMERALD Platform, and EMERALD’s know-how, algorithms, processes, machine learning models, metrics, biomarkers, and Intellectual Property Rights and any supporting proprietary information and materials (whether in physical, hard copy or digital form) containing or comprising the same. 1.4. “EMERALD Information” shall mean any and all information and data, including without limitation the EMERALD Technology, EMERALD DATA, and ancillary data collected by EMERALD to provide the Emerald services in the performance of an SOW under this Agreement, in whatever format, whether electronically, in writing, or orally. 1.9. “Confidential Information” shall mean any and all non-public information regardless of form, including, without limitation, technical, developmental, marketing, sales, operating, performance, cost, know-how, business plans, business methods, process information, database information, software, algorithms, software licenses, applications, written code, logs, and graphical art disclosed to the other Party. 5. CONFIDENTIAL INFORMATION AND PUBLICATION 5.1 COMPANY Information is considered COMPANY’s Confidential Information, and EMERALD Information is considered EMERALD’s Confidential Information, with the exclusion of EMERALD DATA and SUPPORTING DATA, which are subject to section 3.4 above. 5.2. Nondisclosure of Confidential Information. All Confidential Information disclosed by one Party to the other Party or that is observed hereunder shall be maintained in confidence by the receiving Party and shall not be (a) disclosed to any Third Party except to those of its directors, officers, employees, contractors, agents, potential investors, and consultants (including accountants and attorneys) (“Representatives”), whose duties require them to have access to such Confidential Information and are bound by confidentiality and non-use obligations that are at least as stringent as those herein or (b) used for any purpose except as set forth herein, without the prior written consent of the disclosing Party, except to the extent that such Information: (i) is publicly available by public use and/or publication before its receipt from the disclosing Party, or thereafter become publicly available through no fault of the receiving Party; (ii) was already in the receiving Party’s possession prior to receipt from the disclosing Party, as evidenced by records kept by receiving Party in the ordinary course of business; (iii) is properly obtained by receiving Party from a Third Party which has a valid right to disclose such information to receiving Party, is not under a confidentiality obligation to the disclosing Party, and is not disclosing such information to receiving Party on behalf of the disclosing Party; or (iv) is developed by the receiving Party independently of Information received from the disclosing Party, as documented by the receiving Party’s business records. 5.3. Legal Exception. If a Party is required by judicial or administrative process to disclose Information that is subject to the non-disclosure provisions of this Section, such Party shall promptly inform the other Party of the disclosure that is being sought, unless such Party is legally barred from doing do, in order to provide the other Party an opportunity to challenge or limit the disclosure obligations. Information that is disclosed by judicial or administrative process shall remain otherwise subject to the confidentiality and non-use provisions of this Paragraph 5, and the Party disclosing Information pursuant to Applicable Laws or court order shall use its reasonable efforts, including reasonably assisting the non-disclosing Party in attempting to obtain an order of confidentiality, to ensure the continued confidential treatment of such Information. Information that is disclosed by judicial or administrative process shall remain otherwise subject to the confidentiality and non-use provisions set forth herein. 5.4. Confidentiality Obligation. The receiving Party shall keep confidential any Confidential Information of the disclosing Party using at least the same degree of care that it uses to protect its own Confidential Information of a similar nature, which shall be no less than a reasonable degree of care. These obligations of confidentiality and non-use shall be in effect during the Term and continue for five (5) years after the Term ends, provided, however, with respect to any Confidential Information that constitutes a trade secret (as determined under application law), such restrictions on disclosure and/or use shall survive after the Term ends for as long as such Confidential Information remains a trade secret but, in no event, shall such restrictions on disclosure and/or use cease prior to the expiration of five (5) years after the Term ends. 5.5. Disclosure Implications. Each Party understands and agrees that the material breach of this Section by a receiving Party may cause irreparable injury to the disclosing Party and that monetary damages may not provide an adequate remedy for such material breach, and both Parties hereby agree that, in the event of such a material breach by the receiving Party, the disclosing Party will be entitled to seek injunctive relief and/or specific performance, without prejudice to any other rights and remedies available for such material breach of this Agreement. 5.6. Publicity. Either Party may disclose on its website and/or other written or electronic materials the presence but not the details of this Agreement between COMPANY and EMERALD and may use the name and logo of the other Party in connection with such disclosure.

One Broadway St, 14 th Floor Cambridge, MA 02142 November 26, 2025 Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Request for Confidentiality – FCC FCC ID: 2BSYY-EMHW130627 Pursuant to FCC 47 CFR 0.457(d)(1)(ii) and 0.459 and FCC guidance published in KDB 726920, we hereby request confidential treatment of information accompanying this application as outlined below. We request the exhibits selected below as long term confidential (LTC) be withheld from public view permanently: Selection of exhibits for LTC - general Exhibit name ☒ Permanent (Long Term) Block Diagrams ☒ Permanent (Long Term) Operation Description / Theory of Operation ☒ Permanent (Long Term) Parts List & Placement / BOM ☒ Permanent (Long Term) Schematics We also request the exhibits selected below as short term confidential (STC) be withheld from public view for a period of 60 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public: Selection of exhibits for STC 1 Exhibit name ☒ Short Term External Photos 1 - Any exhibits that may have already been requested to have “Permanent” confidentiality need not be repeated under Short-Term confidentiality request. One Broadway St, 14 th Floor Cambridge, MA 02142 Our company has spent a substantial effort in developing this product and it is one of the first of its kind in the industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. When the device is marketed before the requested number of days listed above, the grantee will inform the TCB to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. The above information contains trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Sincerely, Signed by: Rumen Hristov Signature Print name Dire ctor of Engineering Title 617- 943- 9690 Phone Emerald Innovations, Inc. Company 1 Broadway, 14Fl, Cambridge, MA, USA , 02142 Address

One Broadway St, 14 th Floor Cambridge, MA 02142 Dated: November 26, 2025 Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Request for Special Confidentiality – FCC FCC ID: 2BSYY-EMHW130627 Pursuant to FCC 47 CFR 0.457(d)(1)(ii) and 0.459 and FCC guidance published in KDB 726920, we hereby request confidential treatment of information accompanying this application as outlined below. We request the exhibits selected below as long term confidential (LTC) be withheld from public view permanently: Selection 1 Exhibit name ☒ Internal Photos Furthermore, the device’s internal circuitry and components are not accessible to end users and are designed to be serviced solely by authorized technicians under NDA. All product distributions must be governed by an NDA that protects proprietary information, including internal photographs. A sample NDA is included with this application. Our company has made substantial investments in the development of this innovative product, which represents a first-of-its-kind solution in the industry. Public disclosure of the technical details would compromise our competitive edge and could result in significant financial harm. Safeguarding the confidentiality of our design is critical to protecting our intellectual property. The information provided includes trade secrets and proprietary data not customarily disclosed to the public. Unauthorized disclosure could adversely impact our business and provide competitors with an unfair advantage. Sincerely, Signature: Name: Rumen Hristov Title: Director of Engineering Company: Emerald Innovations, Inc. Address: 1 Broadway, 14Fl, Cambridge, MA 02142 Phone: 617-943-9690 Email: [email protected] 1 - These items require further information to be provided to TCB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and review section II, 3) regarding specific information (NDA) that must accompany these requests. One Broadway St, 14 th Floor Cambridge, MA 02142

One Broadway St, 14 th Floor Cambridge, MA 02142 Emerald Innovations Inc. Confidential and Proprietary. Do Not Distribute. Label and Label Location Exhibit Model Number: HW13 FCC ID: 2BSYY-EMHW130627 Applicant: Emerald Innovations, Inc. Date: 11/25/2025 1. Label Information The product will bear a permanent nameplate or etched label showing the required regulatory identifiers. The label includes: • FCC ID: 2BSYY-EMHW130627 • Contains: PD9AX210NG, NDD9576112101, 2AWAF-GT25G Sample Label Format FCC ID: 2BSYY-EMHW130627 Model: HW13 Designed By Emerald Innovations, Inc. Contains FCC ID: PD9AX210NG, NDD9576112101, 2AWAF-GT25G Text height and contrast shall comply with FCC §2.925 One Broadway St, 14 th Floor Cambridge, MA 02142 Emerald Innovations Inc. Confidential and Proprietary. Do Not Distribute. 2. Label Location The label is located on the rear of the device. Label Location Photo One Broadway St, 14 th Floor Cambridge, MA 02142 Emerald Innovations Inc. Confidential and Proprietary. Do Not Distribute. 3. Permanence of Label The label is: • Permanently affixed to the product housing using one of the following: o Silkscreen printing o Laser engraving o Adhesive label (durable under normal use, per UL 969 or equivalent) • Visible to the user under normal operating conditions (unless e-labeling is used – see below).

www.nemko.com Nemko Canada Inc., a testing laboratory, is accredited by ANSI National Accreditation Board (ANAB). The test results included in this report are within the scope of this accreditation. The ANAB symbol is an official symbol of the ANSI National Accreditation Board, used under licence. FCC and ISED RSS-102– MPE Calculation; Date: June 2025 RF Exposure Compliance – MPE Calculation Report C h o o s e S c a n d i n a v i a n t r u s t Applicant information: Emerald Innovations, Inc. Product information: Description: Contactless in-home health monitoring system Model: HW13 Product type: Mobile or Fixed Device Device category Consumer Device for General Population/Uncontrolled Exposure FCC Identification: FCC ID: 2BSYY-EMHW130627 Date of issue: December 4, 2025 Compliance Specifications: FCC 47 CFR Part 1 Subpart I, §§1.1307, 1.1310 FCC 47 CFR Part 2 Subpart J, §§2.1091, 2.1093 FCC KDB 447498 D01 General RF Exposure Guidance v06 FCC KDB 865664 D01 RF Exposure Procedures and Equipment Authorization Policies MPE calculation report Product info: FCC ID: 2BSYY-EMHW130627 Model: HW13 Page 2 of 6 Test locations of Nemko Canada Inc. Ottawa site Montréal site GTA Cambridge site Facility address 303 River Road Ottawa, Ontario Canada K1V 1H2 Tel: +1 613 737 9680 Fax: +1 613 737 9691 292 Labrosse Avenue Pointe-Claire, Québec Canada H9R 5L8 Tel: +1 514 694 2684 Fax: +1 514 694 3528 1-130 Saltsman Drive Cambridge, Ontario Canada N3E 0B2 Tel: +1 519 650 4811 Test site identifier - FCC CA2040 CA2041 CA0101 ANAB File Number AT-3195 AT-3193 AT-3194 Andrey Adelberg Senior EMC/Wireless Specialist Prepared by Signature Limits of responsibility The results presented in this report apply solely to the specific device model tested and are valid only for the operating conditions and installation requirements specified herein. Testing was conducted in accordance with ISO/IEC 17025:2017 requirements, and all results fall within the scope of Nemko Canada's accreditation. This MPE evaluation is based on the maximum power levels and operating conditions specified. Any modifications to the device hardware, software, or installation that could affect RF output power or antenna characteristics may invalidate this compliance demonstration. Copyright notification This report may be reproduced by the applicant in its entirety for regulatory submission and internal use. Any use of this report by third parties, including reliance on its contents or decisions made based on it, is solely at the risk of those third parties. Nemko Canada Inc. assumes no responsibility for any damages incurred by third parties as a result of actions taken based on this report. © Nemko Canada Inc. All rights reserved. MPE calculation report Product info: FCC ID: 2BSYY-EMHW130627 Model: HW13 Page 3 of 6 1. Executive Summary This report presents the Maximum Permissible Exposure (MPE) analysis for [Product Name] to demonstrate compliance with FCC and ISED RF exposure requirements. The evaluation considers both single transmitter operation and simultaneous multi-transmitter scenarios where applicable. 2. Key Findings Compliance status Complies Critical separation distances 20 cm Special conditions or limitations N/A MPE calculation report Product info: FCC ID: 2BSYY-EMHW130627 Model: HW13 Page 4 of 6 MPE calculations for stand-alone transmission Device Classification Requirements Portable Device Definition (§2.1093) Devices designed for use by a person where the radiating structure is within 20 cm of the user's body require SAR evaluation rather than MPE calculation. Mobile Device Definition Devices installed in vehicles or with permanently installed antennas may use MPE calculations if minimum separation distances can be established. Fixed/Base Station Definition Stationary transmitters with controlled access to antenna locations may use MPE calculations for both occupational and general population exposure scenarios. 3. References, definitions and limits for FCC FCC §2.1091(d) (2) For operations within the frequency range of 300 kHz and 6 GHz (inclusive), the limits for maximum permissible exposure (MPE), derived from whole-body SAR limits and listed in Table 1 in paragraph (e)(1) of this section, may be used instead of whole-body SAR limits as set forth in paragraphs (a) through (c) of this section to evaluate the environmental impact of human exposure to RF radiation as specified in §1.1307(b) of this part, except for portable devices as defined in §2.1093 of this chapter as these evaluations shall be performed according to the SAR provisions in §2.1093. Table 1: §1.1310(e)(1)—Power Density Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Power density (mW/cm 2 ) Averaging time (minutes) (i) Limits for Occupational/Controlled Exposure 0.3–3.0 *(100) ≤6 3.0–30 *(900 / f 2 ) <6 30–300 1.0 <6 300–1500 f / 300 <6 1500–100000 5 <6 (ii) Limits for General Population/Uncontrolled Exposure 0.3–1.34 *(100) <30 1.34–30 *(180 / f 2 ) <30 30–300 0.2 <30 300–1500 f / 1500 <30 1500–100000 1.0 <30 Notes: f = frequency in MHz. * = Plane-wave equivalent power density. MPE calculation report Product info: FCC ID: 2BSYY-EMHW130627 Model: HW13 Page 5 of 6 4. Power density calculation formula The fundamental equation (from page 18 of OET Bulletin 65, Edition 97-01) for calculating power density at a specified distance from an RF source is derived from the far-field assumption: 푆= 푃퐺 4휋푅 2 where: • S = Power density (mW/cm² or W/m²) • P = Power input to antenna (mW or W) • G = Antenna gain (linear ratio, not dB) • R = Distance from radiation center (cm or m) This equation assumes: • Far-field conditions (R > 2D²/λ, where D is largest antenna dimension) are assumed at the evaluation distance of 20 cm • Isotropic power distribution (conservative approach) • Free-space propagation conditions • Worst-case antenna orientation Multiple Transmitter Analysis (if applicable) Total Exposure Ratio (TER) Calculation: TER = Σ(Si/Li) ≤ 1.0 Where: • Si = Po…

Text truncated - open the document above for the full version.

One Broadway St, 14 th Floor Cambridge, MA 02142 Emerald Innovations Inc. Confidential and Proprietary. Do Not Distribute. Dated: December 2, 2025 Subject: Antenna Justification Letter for FCC Part 15 Compliance FCC ID: 2BSYY-EMHW130627 Model Number: HW13 To Whom It May Concern, This letter provides justification for the antenna configuration used in the above-referenced device, submitted for certification under FCC Part 15. Radiated Measurement Justification All compliance testing, including fundamental and spurious emissions, was performed using radiated measurement methods. As such, antenna gain and performance characteristics were inherently captured in the test results. Therefore, no separate antenna gain documentation is required to demonstrate compliance with FCC limits. This approach aligns with the guidance provided in the FCC TCB Workshop (October 2022) and KDB 353028 D01, which allows for a justification statement in lieu of antenna gain documentation when radiated measurements are used exclusively. Antenna Description • Antenna Type: Air-gapped PCB patch antenna • Location: Integrated on the main PCB, as shown in the internal photographs • Dimensions: 25.5 mm × 18.5 mm × 6.6 mm • Estimated Peak Gain: 8.5 dBi • Polarization: Linear • Orientation: Vertical • Frequency Bands Supported: 6-8.5 GHz One Broadway St, 14 th Floor Cambridge, MA 02142 Emerald Innovations Inc. Confidential and Proprietary. Do Not Distribute. Supporting details and materials 1. Electrical Characteristics Fig 15. Antenna Return Loss versus Frequency based on Engineering Simulations 2. Estimated Gain Information • Derived from reference design or engineering simulations • No passive reflectors or lenses are used Fig. 16 Estimated Gain based on Engineering Simulations One Broadway St, 14 th Floor Cambridge, MA 02142 Emerald Innovations Inc. Confidential and Proprietary. Do Not Distribute. Compliance Statement The antenna configuration has not been altered in a way that would affect radiated performance. No external gain-enhancing accessories (e.g., reflectors, lenses) are used. The antenna is permanently affixed and not user-accessible or replaceable. Should you require any additional information or clarification, please do not hesitate to contact us. Sincerely, Rumen Hristov Director of Engineering Emerald Innovations, Inc. [email protected]

https://www.ezurio.com/ 1 © Copyright 2024 Ezurio All Rights Reserved FlexMIMO 6E Wi-Fi 6E Internal Antenna 2400-2500 MHz / 490-5925 MHz / 5925-7125 MHz In 2020 the FCC announced the allocation of a new frequency spectrum for Wi-Fi applications, extending the frequencies up to 7125 MHz. The FlexMIMO 6E two-port MIMO antenna supports this extended Wi-Fi of 2400- 2500, 4900-5925, and 5925-71…

Text truncated - open the document above for the full version.