2BTNK-DP-1220258x6 Dual Pump

8x6 Dual Pump User Manual This guide will walk you through setting up and using your 86 Dual Pump for automated control of vacuum, pressure, and heat. 1. Getting Started: Device Setup Before you begin, let's get your device powered up correctly. Identifying the Power Ports Your device has two DC power ports that serve different functions. It is critical to use the correct one for power. Power Input: Located on the side of the case that has only one port. The main power button is next to it. Heat Pad Output: Located on the other side, alongside the tube connectors and control buttons. Do NOT plug the main power cable in here. This port is exclusively for powering an optional heat pad. Understanding the Device Buttons Your device has physical buttons for direct control without the app. Note: Throughout this manual, "long press" refers to pressing and holding a button for 1 second. Power Button Location: On the top of the case, near the Power Input port. Functions: Short press (during operation): Pause current operation Short press (while paused): Resume operation Long press: Power off device Note: The device automatically powers on when connected to a power source. 86 Dual Pump User Manual1 Control Buttons (Top of Case) These three buttons are located near the tube connectors. Button 1  Release Negative Pressure Abo ve left tube connector) Short press: Releases the vacuum and stops any running sequence Long press: Calibrates the pressure sensor (indicator light flashes during calibration and stops when complete) Button 2  Release Positive Pressure Abo ve middle tube connector) Short press: Releases positive pressure and stops any running sequence Long press: Calibrates the pressure sensor (indicator light flashes during calibration and stops when complete) Button 3  Heat Pad Control Abo ve DC output port) Short press (when off): Activates 12V output (indicator light flashes slowly) Long press (when off): Activates 24V output (indicator light flashes quickly) Short press (when on): Turns off the heat pad Mechanical Release Valves Each pressure circuit has a manual release valve that can be pressed down to immediately release pressure. These provide a fail-safe mechanism independent of electronic control. Powering On the Device  Plug the included DC power cable into the Power Input port.  Plug the adapter into a wall outlet.  The device will automatically power on and enter standby mode.  Proceed to connect the device to the mobile app. Factory Reset To restore factory default settings:  Disconnect the device from power. 86 Dual Pump User Manual2  Press and hold the power button.  While continuing to hold the power button, connect the device to power.  Continue holding the power button for 15 seconds. During the process the LED will blink, once the reset is done the LED will stop blinking.  Release the power button. The device will reset all settings to factory defaults. 2. Connecting via the "8x6" App Your pump is controlled wirelessly with our dedicated mobile app.  Download the App: Search for and install the "86" app from the Google Play Store or Apple App Store.  Open the App: Launch the app.  Enable Wireless: Make sure wireless connectivity is enabled on your smartphone.  Scan for Devices: In the app, tap on "Scan for devices".  Connect: Select the device from the list to establish a connection.  Confirmation: A new light will appear on your device, confirming a successful connection. 3. How to Use the App The app is organized into tabs for easy navigation. Direct Control Tab This tab allows you to manually control the device's functions in real-time. Vacuum Pressure:  Adjust the "Vacuum Control" slider to your desired pressure level.  Tap the "Set Vacuum Pressure" button to apply the setting. Inflation / Positive Pressure: 86 Dual Pump User Manual3  Adjust the "Pressure Control" slider.  Tap the "Set Inflation Pressure" button to apply the setting. Heat Pad Control:  To turn the heat pad on, toggle the "Heat Pad Power Status" switch to ON and tap "Set Status".  To turn it off, toggle the switch to OFF and tap "Set Status".  If your heat pad requires 24V, select 24V under "Power Level" and tap "Set Power". Emergency Stop: To immediately release all pressure (both vacuum and inflation), stop any running sequence, and turn off the heat pad, press the floating "Stop | Release" button at any time. Routines Tab Create custom, automated sequences of actions for your device. Routines are transmitted to the device and execute autonomously, so your phone does not need to remain connected during execution. To Create a New Routine:  Navigate to the "Routines" tab.  Tap the "Create New Routine" button (usually in the bottom right corner).  Enter a descriptive name for your routine.  Add steps by tapping buttons for the following actions: Vacuum Pressure  Set negative pressure to a specified value Inflation Pressure  Set positive pressure to a specified value Wait  Pause for a specified duration Heat Pad On  Enable the heat pad output Heat Pad Off  Disable the heat pad output Heat Pad 12V  Set heat pad voltage to 12V 86 Dual Pump User Manual4 Heat Pad 24V  Set heat pad voltage to 24V Sub-Routine  Insert a previously created routine as a nested sequence  Configure the settings for each step you add.  Under "Sequence Settings," choose how the routine will end: Duration: The routine repeats continuously until the specified total duration elapses. Cycles: The routine executes a specified number of times.  Tap "Save Routine". Nested Routines Sub-Routines): You can incorporate previously created routines as sub-routines within a parent routine. This allows you to build complex sequences from simpler building blocks. Each sub-routine can have its own independent duration or cycle settings. To Run a Routine:  Go to the "Main" tab.  Select your desired routine from the list.  Optional) You can override the saved cycle coun…

Text truncated - open the document above for the full version.

CoveredEquipmentAttestationLetter ForCertificationServiceintheUSA FederalCommunicationsCommission EquipmentAuthorizationDivision,ApplicationProcessingBranch 7435OaklandMillsRoad Columbia,MD21048 Towhomitmayconcern PursuanttoSection2.911(d)(5)(i)-(ii)oftheCommission’sRules(47C.F.R.)weattestas followsfortheproductlistedbelow: FCCIDModelname 2BTNK-DP-122025DP-122025 We, Applicant CompanyName:MountainMoleculesLimited Address:Unit2A,17/F,GlenealyTower,No.1 GlenealyCentral,HongKongS.A.R Phone:85230016135 certifythattheequipmentforwhichauthorizationissoughtisnot“covered”equipment prohibitedfromreceivinganequipmentauthorizationpursuanttosection2.903oftheFCC rules.Thisincludesthecybersecurityandanti-virussoftwareproducedorprovidedby KasperskyLab,Inc.oranyofistsuccessorsandassignees. Wecertifythat,asofthedateofthefilingoftheapplication,theapplicantisnotidentified ontheCoveredListasanentityproducing“covered”equipment. Ifyouhaveanyquestions,pleasefeelfreetocontactusattheaddressshownbelow. Sincerely, 2026-01-07 SignatureDate PrintedNameofSignee:Abdourahmane Seck Company:MountainMoleculesLimited Phone:85230016135 Email:[email protected] Address:Unit2A,17/F,GlenealyTower, No.1Glenealy,Central,HongKongS.A.R Fax:N/A

ConfidentialityRequestLetter ForCertificationServiceintheUSA FederalCommunicationCommission EquipmentAuthorizationDivision,ApplicationProcessingBranch 7435OaklandMillsRoad Columbia,MD21048 Towhomitmayconcern PursuanttoParagraphs§0.457and0.459oftheCommission’sRules(47C.F.R.)andSection §552(b)(4)oftheFreedomofInformationAct,werequestconfidentialityforthe documentationofthefollowingproducts: FCCIDModelname 2BTNK-DP-122025DP-122025 Fortheproductslistedabove,werequestpermanentconfidentialityforallapplicable exhibitsasthereare:  theOperationalDescription  theBlockDiagram theSchematics Theabovelistedexhibitscontaintradesecretsandproprietaryinformationthatcouldbeof benefittoourcompetitors. Ifyouhaveanyquestions,pleasefeelfreetocontactusattheaddressshownbelow. Sincerely, 2026-01-07 SignatureDate PrintedNameofSignee/Title:AbdourahmaneSeck/Director Company:MountainMoleculesLimited Address:Unit2A,17/F,GlenealyTower,No.1Glenealy Central,HongKongS.A.R Phone:85230016135 Fax:-- Email:[email protected]

ReportNo.:CISRR25121530301 Page 58 of 61 9.EXTERNALANDINTERNALPHOTOS 9.1.ExternalPhotos ReportNo.:CISRR25121530301 Page 59 of 61

Label Label Location

ReportNo.:CISRR25121530301 Page 60 of 61 9.2.InternalPhotos ReportNo.:CISRR25121530301 Page 61 of 61 ------Endofthereport----- ANT

ReportNo.: CISRR25121530302 Reporttemplateversion:CISE-TR-001-A0Page:1of6 TESTREPORT RFExposureEvaluation ReportNo.: CISRR25121530302 ProjectNo.: CISR251215303 FCCID:2BTNK-DP-122025 Applicant:MountainMoleculesLimited Address: Unit2A,17/F,GlenealyTower,No.1Glenealy Central,HongKongS.A.R Manufacturer: MountainMoleculesLimited Address: Unit2A,17/F,GlenealyTower,No.1Glenealy Central,HongKongS.A.R ProductName: 8x6DualPump TradeMark:- Model/Typereference:DP-122025 ListedModel(s):- Standard:47CFRPart2.1091 Issuedate:December22,2025 Testresult:Complied Reviewedby:MorganTan Approvedby:HansHu Thetestresultsrelateonlytothetestedsamples. ThetestreportshouldnotbereproducedexceptinfullwithoutthewrittenapprovalofShenzhenBangceTesting TechnologyCo.,Ltd. ReportNo.: CISRR25121530302 Reporttemplateversion:CISE-TR-001-A0Page:2of6 1.APPLICABLESTANDARD 47CFRPart2.1091:Radiofrequencyradiationexposureevaluation:mobiledevices ANSIC95.1–3999:IEEEStandardforSafetyLevelswithRespecttoHumanExposuretoRadioFrequency ElectromagneticFields,3kHzto300GHz. FCCKDBpublication447498D01GeneralRFExposureGuidancev06:MobileandPortableDevicesRF ExposureProceduresandEquipmentAuthorizationPolicies. 47CFRPart1.1307:Actionsthatmayhaveasignificantenvironmentaleffect,forwhichEnvironmental Assessments(EAs)mustbeprepared. 47CFRPart1.1310:Radiofrequencyradiationexposurelimits. 2.REPORTVERSION VersionNo.IssuedateDescription 00December22,2025Original ReportNo.: CISRR25121530302 Reporttemplateversion:CISE-TR-001-A0Page:3of6 3.RADIOSPECIFICATIONDESCRIPTION Bluetooth Supportedtype:BREDRLE-1Mbps LE-2Mbps Note:PleaserefertoRFreportfordetailedtechnicalspecifications 4.SIMULTANEOUSTRANSMISSIONANALYSIS ThesedevicesuseasingletransmittermoduleandantennaforbothBT,BTcannottransmitsimultaneously. ReportNo.: CISRR25121530302 Reporttemplateversion:CISE-TR-001-A0Page:4of6 5.TESTRESULT 5.1.SARtestexclusionEvaluation ExclusionLimit: KDB447498D01v06,Clause4.3.1b) 100MHzto1500MHz {[Powerallowedatnumericthresholdfor50mminstepa)]+[(testseparation distance–50mm)·(f(MHz)/150)]}mW 1500MHzand≤6GHz {[Powerallowedatnumericthresholdfor50mminstepa)]+[(testseparation distance–50mm)·10]}mW Result: Passed TestData Radiotype Frequency (GHz) Maximum output power #1 (dBm) Antenna gain #2 (dBi) Maximum EIRP #3 (dBm) Maximum tune-upEIRP #4 (dBm) Minimum distance #5 (mm) Exclusion Limit (dBm) Result Bluetooth2.4802.302.3384.638520032.03PASS Note #1:ThisvaluecomesfromtheRFtestreport. #2:Thisvalueisdeclaredbytheapplicant. #3:EIRP=Maximumoutputpower+Antennagain. #4:Thisvalueisdeclaredbytheapplicant. #5:Thisvalueisdeclaredbytheapplicant. ReportNo.: CISRR25121530302 Reporttemplateversion:CISE-TR-001-A0Page:5of6 5.2.Standalonetransmission Limit: Thecriterialistedinthefollowingtableshallbeusedtoevaluatetheenvironment impactofhumanexposuretoradiofrequency(RF)radiationasspecifiedin1.1307(b) LimitsforMaximumPermissibleExposure(MPE) Frequency range(MHz) Electricfield strength(V/m) Magneticfield strength (A/m) Powerdensity (mW/cm 2 ) Averaging time(minutes) (A)LimitsforOccupational/ControlledExposures 0.3–3.06141.63*(100)6 3.0–301842/f4.89/f *(900/f 2 ) 6 30–30061.40.1631.06 300–1500--f/3006 1500–100,000--56 (B)LimitsforGeneralPopulation/UncontrolledExposure 0.3–1.346141.63*(100)30 1.34–30824/f2.19/f *(180/f 2 ) 30 30–30027.50.0730.230 300–1500--f/150030 1500–100,000--1.030 Evaluationmethod: Pd=(Pout*G)/(4*pi*r 2 ) Where Pd=powerdensityinmW/cm 2 ,Pout=outputpowertoantennainmW, G=gainofantennainlinearscale,Pi=3.1416, R=distancebetweenobservationpointandcenteroftheradiatorincm Result:Passed TestData Radiotype Maximum outputpower (dBm) #1 Maximum tune-uppower (dBm) Antenna gain(dBi) #2 Minimun distance(cm) #3 Pd (mW/cm 2 ) Limit (mW/cm 2 ) Result Bluetooth2.303.002.33820.000.00071.00PASS Note #1:ThisvaluecomesfromtheRFtestreport. #2:Thisvalueisdeclaredbytheapplicant. ReportNo.: CISRR25121530302 Reporttemplateversion:CISE-TR-001-A0Page:6of6 5.3.Simultaneoustransmission Limit: KDB447498D01v06,Clause4.3.2,47CFRPart1.1307 InthecaseofxedRFsourcesoperatinginthesametime-averagingperiod,orof multiplemobileorportableRFsourceswithinadeviceoperatinginthesametime averagingperiod,ifthesumofthefractionalcontributionstotheapplicablethresholds islessthanorequalto1asindicatedinthefollowingequation. Where a=numberoffxed,mobile,orportableRFsourcesclaimingexemptionusingparagraph (b)(3)(i)(B)ofthissectionforP,includingexistingexempttransmittersandthosebeing added. b=numberoffxed,mobile,orportableRFsourcesclaimingexemptionusingparagraph (b)(3)(i)(C)ofthissectionforThresholdERP,includingexistingexempttransmittersand thosebeingadded. c=numberofexistingfixed,mobile,orportableRFsourceswithknownevaluationforthespeci edminimumdistanceincludingexistingevaluatedtransmitters. P j =theavailablemaximumtime-averagedpowerortheERP,whicheverisgreater,forxed, mobile,orportableRFsourceiatadistancebetween0.5cmand40cm(inclusive). P th,j =theexemptionthresholdpower(P)accordingtoparagraph(b)(3)(i)(B)ofthissectionfor xed,mobile,orportableRFsourcei. ERP j =theERPoffixed,mobile,orportableRFsourcej. ERP th,j =exemptionthresholdERPforfixed,mobile,orportableRFsourcej,atadistanceofat leastλ/2πaccordingtotheapplicableformulaofparagraph(b)(3)(i)(C)ofthissection. Evaluated k =themaximumreportedSARorMPEoffixed,mobile,orportableRFsourcekeither inthedeviceoratthetransmittersitefromanexistingevaluationatthelocationofexposure. ExposureLimit k =eitherthegeneralpopulation/uncontrolledmaximumpermissibleexposure (MPE)orspecicabsorptionrate(SAR)limitforeachxed,mobile,orportableRFsourcek, asapplicablefrom§1.1310ofthischapter. Result:NotApplicable --------EndofReport--------

2.4G-2.48GANT-2.4GAntennaData Sheet SPECIFICATIONS Frequency（MHz）2400-2480 PeakGain（dBi）2.338 AverageGain（dBi）＞-5.5 VSWR＜3.2 Impedance（Ω）50Ω AntennaTypePlannarInverted2.4GAntennaonboard PolarizationLinear ManufactureShenzhenHuihuaElectronicsCo.,Ltd Address:1701-6,Building4A,HuaqiangCreativeIndustryPark,Intersectionof SightseeingRoadandKetaiRoad,BlueEyeCommunity,GuangmingStreet, GuangmingDistrict,ShenzhenCity,GuangdongProvince TestequipmentShenzhenHongxinTechnologyElectronicsCo.,Ltd 天线无源S参数： AntennapassiveS-parameters: 驻波比（VSWR）、回波损耗（ReturnLoss）及史密斯圆图（Smith） 天线效率及增益： Antennaefficiencyandgain： Frequency（MHz）Gain（dBi）Effciency（%）AverageGain（dBi）Efficiency（dB） 24002.33859.39%-2.915-2.263 24101.60349.11%-3.883-3.088 24201.29546.04%-4.014-3.369 24300.38836.89%-4.91-4.331 24400.18734.00%-5.276-4.685 24500.0231.71%-5.431-4.988 24600.50734.88%-5.02-4.575 24700.29131.89%-5.323-4.963 24800.42932.89%-5.195-4.83 Average0.7839.64%-4.66-4.12 Peak2.33859.39%-2.915-2.263 天线2400MHz2D-ThetaPattern 天线2400MHz2D-PhiPattern 2400MHz3D-TotalPattern

ReportNo.:CISRR25121530301 Thetestresultsrelateonlytothetestedsamples. ThetestreportshouldnotbereproducedexceptinfullwithoutthewrittenapprovalofShenzhenBangce TestingTechnologyCo.,Ltd. Page1of54 TESTREPORT ReportNo.CISRR25121530301 ProjectNo.CISR251215303 FCCID2BTNK-DP-122025 ApplicantMountainMoleculesLimited Address Unit2A,17/F,GlenealyTower,No.1Glenealy Central,HongKongS.A.R ManufacturerMountainMoleculesLimited Address Unit2A,17/F,GlenealyTower,No.1Glenealy Central,HongKongS.A.R ProductName8x6DualPump Trademark- Model/TypereferenceDP-122025 ListedModel(s)- Standard 47CFRPart15.247 DateofsamplereceiptDecember16,2025 TestdateDecember16,2025toDecember19,2025 IssuedateDecember22,2025 TestresultComplied Reviewedby:MorganTan Approvedby:HansHu ReportNo.:CISRR25121530301 Page 2 of 54 Contents 1.STANDARDANDAPPLICABLETESTMETHODS........................................................................................3 2.REPORTVERSION..........................................................................................................................................3 3.TESTDESCRIPTION.......................................................................................................................................4 4.SUMMARY........................................................................................................................................................5 4.1.ProductDescription*..................................................................................................................................5 4.2.RadioSpecificationDescription*..............................................................................................................5 4.3.ModificationofEUT.....................................................................................................................................6 4.4.Deviationfromstandards...........................................................................................................................6 4.5.TestingSite...................................................................................................................................................6 5.TESTCONFIGURATION.................................................................................................................................7 5.1.Testfrequencylist.......................................................................................................................................7 5.2.Descriptionsoftestmode...........................................................................................................................7 5.3.Supportunitusedintestconfiguration....................................................................................................7 5.4.Testsampleinformation.............................................................................................................................7 5.5.Environmentalconditions...........................................................................................................................7 5.6.Statementofthemeasurementuncertainty.............................................................................................8 5.7.EquipmentUsedduringtheTest................................................................................................................9 6.TESTRESULTS.............................................................................................................................................11 6.1.EvaluationResults(Evaluation)...............................................................................................................11 6.1.1.AntennaRequirement.............................................................................................................................11 6.2.RadioSpectrumMatterTestResults(RF)...............................................................................................12 6.2.1.ConductedEmissionatACpowerline.................................................................................................12 6.2.2.MaximumConductedOutputPower.....................................................................................................15 6.2.3.ChannelSeparation................................................................................................................................16 6.2.4.NumberofHoppingFrequencies..........................................................................................................17 6.2.5.DwellTime...............................................................................................................................................18 6.2.6.Conductedbandedgeandspuriousemission...................................................................................20 6.2.7.Radiatedbandedgeemission...............................................................................................................22 6.2.8.RadiatedSpuriousEmission(below1GHz).........................................................................................28 6.2.9.RadiatedSpuriousEmission(Above1GHz)........................................................................................32 7.APPENDIXREPORT......................................................................................................................................40 7.1.ConductedOutputPower.........................................................................................................................40 7.2.20dBBandwidth.........................................................................................................................................42 7.3.DutyCycle..................................................................................................................................................44 7.4.NumberOfHoppingChannel...................................................................................................................46 7.5.CarrierFrequenciesSeparati…

Text truncated - open the document above for the full version.

ReportNo.:CISRR25121530301 Page 56 of 61 8.TESTSETUPPHOTOS ConductedEmissionatACpowerline Radiatedbandedgeemission RadiatedSpuriousEmission(Above1GHz) ReportNo.:CISRR25121530301 Page 57 of 61 RadiatedSpuriousEmission(below1GHz)