2BTU5-WE-22-984WRMelody WE-22-984WR

Quality Surpassing standards from Europe and America. Material Safety All Honey Play Box products are manufactured using enviromental friendly materials including Silicone and ABS plastics. They are harmless to human body. International Certification Honey Play Box products have passed EU ROHS certification and meet EU CE Directive and WEEE Directive.Honey Play Box products are “Green” meeting the official safety and environmental protection standard issued by agencies in Europe and North America. Additional Information: The EU CE Directive and the WEEE Directive are referred to as the “Twin Directives for Environmental Protection” or “Double Green Directives” and are used to restrict hazardous substances in electronic products including lead, cadmium, and mercury. ROHS stands for “Restriction of the Use of Certain Hazardous Substances”; and WEEE stands for “Waste Electrical and Electronic Equipment”. Products that meet the standards set pout in these two directives can be advertised as“Green Products”. EU CE Directive: Is the collective name of a series of product standards issued by the European Union; enterprises complying with the standard may apply for CE certification mark on their products and labelling. Honey Play Box products surpass the standards set out by these directives and are authorized to use the mark identifying that the products comply with all EU requirements. 01 WARNING! Proper maintenance and care will extend the product’s lifespan. Please read the following safety instructions carefully. Before Use: Clean product thoroughly and scrub with antibacterial soap. Rinse with clean, hot water. Gently wipe dry with a towel or soft cloth. During Use: Do NOT use massage oil or hand cream as a lubricant. Do NOT use silicone-based lubricants, as they can damage the organosilicon surface. Reminder: Avoid using cleaning agents that contain alcohol, gasoline, or acetone to wipe the product. Keep the product away from direct sunlight and prolonged exposure to high. Maintenance of the Built-in Battery: This product uses rechargeable batteries, which reach full effectiveness after two or three charging and discharging cycles. The battery can be charged and discharged over 100 times and will mature over time. Once fully charged, it should be disconnected from the charger to prevent overcharging, which may reduce battery life. When the product is idle, the battery will gradually lose charge. Exposure to extreme hot or cold temperatures can decrease battery capacity and shorten its lifespan. Even if fully charged, a battery exposed to extreme temperatures will have a reduced lifespan. Battery Warning: If the battery is damaged or tampered with, it may cause fire or chemical burns. There is also a risk of explosion. Dispose of the battery in accordance with local laws and regulations. If possible, recycle it. Users should not attempt to remove or replace the battery themselves, as improper handling may damage the product. 02 02 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. EN EN EN Light Indicator Maintenance Wash thoroughly with soapy water or toy cleaner. Air dry or dry with a clean towel. Store in a cool, dry, and dust-free place, away from direct sunlight. Charging: Light flashes Fully charged: Light stays on permanently While in use: Light remains on Attention This product is for adult use only—keep out of reach of children. It is recommended to use water-based lubricants. If you feel any discomfort during use, stop immediately. EN APP Control This product is APP-enabled. Search for "HoneyPlayBox" on the Apple Store or Google Play to download the app. Sign Up & Login: After installing the "HoneyPlayBox" app, complete the registration process and log in to your account. Activation: Turn on your product and enable Bluetooth on your phone. Connect: Click on "Bluetooth Connect" in the app. It will detect nearby devices. Select your toy, then tap "Connect." Once paired, the app will automatically direct you to the "Presets" page. Our app gets updated constantly. Scan the QR code below to explore our latest detailed App Guide or visit this link: https://www.honeyplaybox.com/collections/app. ES ES ES Indicadores de luz Mantenimiento Lave a fondo con agua jabonosa o limpiador de juguetes. Séquelo al aire o con una toalla limpia. Guárdelo en un lugar fresco, seco y libre de polvo, alejado de la luz solar directa. …

Text truncated - open the document above for the full version.

UC GLOBAL TRADE INC U.S. Agent Designation for Service of Process (Applicant and U.S. Agent are Separate Parties) TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: UC GLOBAL TRADE INC Address: 14225 Telephone Ave, Unit# D (Dock# 10-14), Chino CA 91710, USA FRN: 0037776267 Contact Name: Susan ZH Tel.: 909 685 5987 Email: [email protected] This letter is to confirm that we (“the Designated U.S. Agent”) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Susan ZH Date: 2026/01/26 Signed by (Printed Name/Title): Susan ZH/ Manager The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: UC GLOBAL TRADE INC Grantee Code: 2BTU5 FCC ID: 2BTU5-WE-22-984WR Contact Name: Susan ZH Street Address: 14225 Telephone Ave, Unit# D (Dock# 10-14), Chino CA 91710, USA Telephone No: 909 685 5987 Email: [email protected] FRN: 0037776267 Applicant Signature: Susan ZH Date: 2026/01/26 Signed by (Printed Name/Title): Susan ZH/ Manager

UC GLOBAL TRADE INC 2026/01/26 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for 2BTU5-WE-22-984WR [UC GLOBAL TRADE INC] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, the equipment does not utilize cyber-security or anti-virus software from Kaspersky Lab, Inc, or any of its successors and assignees, which is also on the “covered list”. Sincerely, Name: Susan ZH/ Manager Susan ZH UC GLOBAL TRADE INC 2026/01/26 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for FCC ID: 2BTU5-WE-22- 984WR [UC GLOBAL TRADE INC] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Name: Susan ZH/ Manager Susan ZH

Declaration on model difference We The main model and subsequent models tested in this test differ only in naming and color. All other aspects, including materials, other manufacturing processes, circuit design, and manufacturers, are exactly the same FCC ID: 2BTU5-WE-22-984WR Production name Trade name Model no. 2BTU5-WE-22-984WR Honey Play Box Melody WE-22-984WR,Melody WE-22-984BLU Signature: Susan ZH Date: 2026/01/26 Name: Susan ZH Title: Manager Company: UC GLOBAL TRADE INC

UC GLOBAL TRADE INC 2026/01/26 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: CONFIDENTIALITY REQUEST FOR Product Name: Melody WE-22-984WR FCC ID: 2BTU5-WE-22-984WR Model(s): Melody WE-22-984WR,Melody WE-22-984BLU To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the - Block Diagram - Schematics - Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Client’s signature: Susan ZH Client’s name / title : Susan ZH/ Manager Contact information / address: UC GLOBAL TRADE INC/ 14225 Telephone Ave, Unit# D (Dock# 10-14), Chino CA 91710, USA

UC GLOBAL TRADE INC 2026/01/26 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: LETTER OF AGENT AUTHORIZATION Product Name: Melody WE-22-984WR FCC ID: 2BTU5-WE-22-984WR Model(s): Melody WE-22-984WR,Melody WE-22-984BLU To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen STS Test Services Co., Ltd. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Client’s signature: Susan ZH Client’s name / title : Susan ZH/ Manager Contact information / address: UC GLOBAL TRADE INC/ 14225 Telephone Ave, Unit# D (Dock# 10-14), Chino CA 91710, USA

External Photos

.

Internal Photos ANT

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the ShenZhen STS Test Services Co., Ltd. MPE Report Report No.: STS2512484H01 Issued for UC GLOBAL TRADE INC 14225 Telephone Ave, Unit# D (Dock# 10-14), Chino CA 91710, USA. Product Name: Melody WE-22-984WR Brand Name: Honey Play Box Model Name: Melody WE-22-984WR Series Model(s): Melody WE-22-984BLU FCC ID: 2BTU5-WE-22-984WR Test Standards: FCC 47CFR §2.1093 Page 2 of 8 Report No.: STS2512484H01 TEST REPORT Applicant’s Name ................. : UC GLOBAL TRADE INC Address ................................. : 14225 Telephone Ave, Unit# D (Dock# 10-14), Chino CA 91710, USA. Manufacturer's Name ........... : UC GLOBAL TRADE INC Address ................................. : 14225 Telephone Ave, Unit# D (Dock# 10-14), Chino CA 91710, USA. Product Description Product Name ........................ : Melody WE-22-984WR Brand Name .......................... : Honey Play Box Model Name .......................... : Melody WE-22-984WR Series Model(s) ...................... : Melody WE-22-984BLU Test Standards ..................... : FCC 47CFR §2.1093 447498 D01 Interim General RF Exposure Guidance v06 The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the ShenZhen STS Test Services Co., Ltd. Date of Test ........................................... : Date of receipt of test item ...................... : 2025-12-10 Date (s) of performance of tests ............. : 2025-12-10 to 2025-12-17 Date of Issue .......................................... : 2025-12-26 Test Result .............................................. : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Skylar Li) Authorized Signatory : (Bovey Yang) Page 3 of 8 Report No.: STS2512484H01 TABLE OF CONTENTS 1. GENERAL INFORMATION 5 1.1 GENERAL DESCRIPTION OF THE EUT 5 1.2 TEST FACTORY 5 2. FCC 47CFR §2.1093 REQUIREMENT 6 2.1 TEST STANDARDS 6 2.2 LIMIT 6 2.3 TEST RESULT 8 Page 4 of 8 Report No.: STS2512484H01 Revision History Rev. Issue Date Report No. Effect Page Contents 00 2025-12-26 STS2512484H01 ALL Initial Issue Page 5 of 8 Report No.: STS2512484H01 1. GENERAL INFORMATION 1.1 GENERAL DESCRIPTION OF THE EUT Product Name Melody WE-22-984WR Brand Name Honey Play Box Model Name Melody WE-22-984WR Series Model(s) Melody WE-22-984BLU Model Difference All the model are the same circuit and RF module, except model names and the shell appearance of color. Product Description The EUT is a Melody WE-22-984WR Operation Frequency: 2402–2480 MHz Modulation Type: GFSK(1Mbps) Antenna gain: 3.85dBi Antenna Designation: Internal antenna Power Rating DC 3.7V Adapter N/A Battery DC 3.7V 350mAh Hardware Version N/A Software Version N/A 1.2 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 Page 6 of 8 Report No.: STS2512484H01 2. FCC 47CFR §2.1093 REQUIREMENT 2.1 TEST STANDARDS The limit for Maximum Permissible Exposure (MPE) specified in KDB 447498 D01 General RF Exposure Guidance v06 is followed. The gain of the antennas used in the product is extracted from the Antenna data sheets provided and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis Transmission formula is far field assumption, the calculated result of that is an over-prediction for near field power density. It is taken as worst case to specify the safety range. 2.2 LIMIT Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. Page 7 of 8 Report No.: STS2512484H01 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] • [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,where f(GHz) is the RF channel transmit frequency in GHz. Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Page 8 of 8 Report No.: STS2512484H01 2.3 TEST RESULT Maximum measured transmitter power. Worst Case Mode frequency Maximum Output Power Tune up tolerance Max Tune up GHz dBm dBm dBm GFSK(BLE) 2.402 2.9 2±1 3 Evaluation Result Mode Frequency Antenna Distance RF output power including tune up (dBm) SAR Test Exclusion Threshold SAR Test Exclusion Estimated SAR GHz mm dBm mw GFSK(BLE) 2.402 5 3 1.995 0.6185 Yes / Note: 1. Remark: The worst case gain of the antenna is 3.85dBi. 2. Threshold at which no SAR required is 0.6185≤ 3.0 for 1-g SAR, Separation distance ≤ 5mm. ※※※※※END OF THE REPORT※※※※※

Antenna Photo & Length Length = 80mm Diameter = 1.0mm

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Radio Test Report Report No.: STS2512484W01 Issued for UC GLOBAL TRADE INC 14225 Telephone Ave, Unit# D (Dock# 10-14), Chino CA 91710, USA. Product Name: Melody WE-22-984WR Brand Name: Honey Play Box Model Name: Melody WE-22-984WR Series Model(s): Melody WE-22-984BLU FCC ID: 2BTU5-WE-22-984WR Test Standards: FCC Part15.247 Page 2 of 50 Report No.: STS2512484W01 TEST REPORT Applicant’s Name ................. : UC GLOBAL TRADE INC Address ................................. : 14225 Telephone Ave, Unit# D (Dock# 10-14), Chino CA 91710, USA. Manufacturer's Name .......... : UC GLOBAL TRADE INC Address ................................. : 14225 Telephone Ave, Unit# D (Dock# 10-14), Chino CA 91710, USA. Product Description Product Name ....................... : Melody WE-22-984WR Brand Name .......................... : Honey Play Box Model Name .......................... : ... : Melody WE-22-984WR Series Model(s) .................... : Melody WE-22-984BLU Test Standards ..................... : FCC Part15.247 Test Procedure ...................... : ANSI C63.10-2020 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the IC requirements. And it is applicable only to the tested sample identified in the report. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Date of Test ........................................... : Date of receipt of test item ..................... : 2025-12-10 Date (s) of performance of tests ............. : 2025-12-10 to 2025-12-17 Date of Issue .......................................... : 2025-12-26 Test Result.............................................. : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Skylar Li) Authorized Signatory : (Bovey Yang) Page 3 of 50 Report No.: STS2512484W01 Table of Contents Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 9 2.3 TEST SOFTWARE AND POWER LEVEL 10 2.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 10 2.5 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 11 2.6 EQUIPMENTS LIST 12 3. EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.2 TEST PROCEDURE 14 3.3 TEST SETUP 14 3.4 EUT OPERATING CONDITIONS 14 3.5 TEST RESULTS 15 4. RADIATED EMISSION MEASUREMENT 17 4.1 RADIATED EMISSION LIMITS 17 4.2 TEST PROCEDURE 19 4.3 TEST SETUP 20 4.4 EUT OPERATING CONDITIONS 20 4.5 FIELD STRENGTH CALCULATION 21 4.6 TEST RESULTS 22 5. CONDUCTED SPURIOUS & BAND EDGE EMISSION 28 5.1 LIMIT 28 5.2 TEST PROCEDURE 28 5.3 TEST SETUP 28 5.4 EUT OPERATION CONDITIONS 28 5.5 TEST RESULTS 28 6. POWER SPECTRAL DENSITY TEST 29 6.1 LIMIT 29 6.2 TEST PROCEDURE 29 6.3 TEST SETUP 29 Page 4 of 50 Report No.: STS2512484W01 Table of Contents Page 6.4 EUT OPERATION CONDITIONS 29 6.5 TEST RESULTS 29 7. BANDWIDTH TEST 30 7.1 LIMIT 30 7.2 TEST PROCEDURE 30 7.3 TEST SETUP 30 7.4 EUT OPERATION CONDITIONS 30 7.5 TEST RESULTS 30 8. PEAK OUTPUT POWER TEST 31 8.1 LIMIT 31 8.2 TEST PROCEDURE 31 8.3 TEST SETUP 31 8.4 EUT OPERATION CONDITIONS 31 8.5 TEST RESULTS 31 9. ANTENNA REQUIREMENT 32 9.1 STANDARD REQUIREMENT 32 9.2 EUT ANTENNA 32 APPENDIX 1-TEST DATA 33 DUTY CYCLE 33 MAXIMUM CONDUCTED OUTPUT POWER 36 -6DB BANDWIDTH 37 MAXIMUM POWER SPECTRAL DENSITY LEVEL 40 BAND EDGE 43 CONDUCTED RF SPURIOUS EMISSION 46 APPENDIX 2- EUT TEST PHOTO 50 Page 5 of 50 Report No.: STS2512484W01 Revision History Rev. Issue Date Report No. Effect Page Contents 00 2025-12-26 STS2512484W01 ALL Initial Issue Page 6 of 50 Report No.: STS2512484W01 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 15.247 Meas Guidance v05r02. FCC Part 15.247,Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS -- 15.247 (a)(2) 6dB Bandwidth PASS -- 15.247 (b)(3) Output Power PASS -- 15.209 Radiated Spurious Emission PASS -- 15.247 (d) Conducted Spurious & Band Edge Emission PASS -- 15.247 (e) Power Spectral Density PASS -- 15.205 Restricted bands of operation PASS -- Part 15.247(d)/ Part 15.209(a) Band Edge Emission PASS -- 15.203 Antenna Requirement PASS -- Note: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2020. Page 7 of 50 Report No.: STS2512484W01 1.1 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 RF output power, conducted ±0.751dB 2 Unwanted Emissions, conducted ±2.888dB 3 All emissions, radiated 9K-30MHz ±2.48dB 4 All emissions, radiated 30M-1GHz ±2.52dB 5 All emissions, radiated 1G-18GHz ±3.48dB 6 All emissions, radiated>18GHz ±4.18dB 7 Conducted Emission (9KHz-150KHz) ±2.48dB 8 Conducted Emission (150KHz-30MHz) ±2.52dB 9 Occupied Channel Bandwidth ±3.6% 10 Power Spectral Density, conducted ±1.214dB 11 Duty Cycle ±3.2% Page 8 of 50 Report No.: STS2512484W01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name Melody WE-22-984WR Brand Name Honey Play Box Model Name Melody WE-22-984WR Series Model(s) Melody WE-22-984BLU Model Difference All the model are the same circuit …

Text truncated - open the document above for the full version.

Page 1 of 2 FCC ID: 2BTU5-WE-22-984WR Setup photo AC Conduction RE (Below 1GHz) Page 2 of 2 FCC ID: 2BTU5-WE-22-984WR RE (Above 1GHz)