2BU2H-2BF2B-C2Smart driving recorder

FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

Rev 1/26/2023 Shenzhen Fuhengye Technology Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2026-03-18 FCC ID: 2BU2H-2BF2B-C2 Ref. #1: Attestation Statements Part 2.911(d)(5)(i) Filing Shenzhen Fuhengye Technology Co., Ltd. certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Shenzhen Fuhengye Technology Co., Ltd. certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Ref. #2: Attestation Statements Part 2.911(d)(5)(ii) Filing Shenzhen Fuhengye Technology Co., Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Applicant: Shenzhen Fuhengye Technology Co., Ltd. Address: Building D2 302, Wanlida Industrial Park, Fuyuan No.1 Road 49th, Heping community, Fuhai Street, Baoan District ShenZhen City Guangdong Province, China Contact Person: Lu Weilong Tel.: 15112365351 Email: [email protected] Sincerely, Signature:

Attestation Statements Date: 2026-03-18 TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA RE: Attestation Statements Part 2.911(d)(7) request for(FCC ID: 2BU2H-2BF2B-C2) Shenzhen Fuhengye Technology Co., Ltd., the undersigned, hereby authorize FCC US Agent, LLC to act as our designated agent for service of process, Shenzhen Fuhengye Technology Co., Ltd. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. FCC US Agent, LLC accepts the responsibility to act as designated agent for service of process. Applicant Information： Company name: Shenzhen Fuhengye Technology Co., Ltd. Contact Name: Lu Weilong Address: Building D2 302, Wanlida Industrial Park, Fuyuan No.1 Road 49th, Heping community, Fuhai Street, Baoan District ShenZhen City Guangdong Province, China Telephone No: 15112365351 Email: [email protected] FRN: 0038102463 Signature: Lu Weilong Agent Information: Company Name: FCC US Agent, LLC Address:3722 Illinois Avenue, Saint Charles, IL, 60174, USA FRN: 0033402884 Contact Name: Tim Payne Telephone No: 708-571-3148 Email: [email protected] Signature: Tim Payne

Shenzhen Fuhengye Technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 19, 2026 Subject; Request for Confidentiality FCC ID: 2BU2H-2BF2B-C2 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Lu Weilong Title: manager

Effective Date: April 2, 2020 QSF 7.6.4-8 – Agent Authorization Letter Template Page 1 of 1 Revision Date: Revision: 0 Shenzhen Fuhengye Technology Co., Ltd. Date：2026-03-18 Product Model Number: C2, C2A, C2G, C2K FCC ID：2BU2H-2BF2B-C2 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following: • Testing • Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. Signature: By: Lu Weilong Contact Listed on FCC Wesbite Title: manager Email: [email protected] On behalf of: Shenzhen Fuhengye Technology Co., Ltd.

Shenzhen Fuhengye Technology Co., Ltd. Declaration Letter of Model Difference Date: 2026-03-18 FCC ID: 2BU2H-2BF2B-C2 Tested Model Number: C2 Adding Model Number(s): C2A, C2G, C2K All Adding Model Number(s) is/are same electrically identical as Tested Model Number. Different resolutions for the front camera. Yours Sincerely, Applicant: Shenzhen Fuhengye Technology Co., Ltd. Address: Building D2 302, Wanlida Industrial Park, Fuyuan No.1 Road 49th, Heping community, Fuhai Street, Baoan District ShenZhen City Guangdong Province, China Contact Person: Lu Weilong Tel.: 15112365351 Email: [email protected] Sincerely, Signature:

Page 1 of 5 Report No.: LGT26A171 Appendix - External Photographs of EUT Constructional Details Photo 1 Photo 2 Page 2 of 5 Report No.: LGT26A171 Appendix - External Photographs of EUT Constructional Details Photo 3 Photo 4 Page 3 of 5 Report No.: LGT26A171 Appendix - External Photographs of EUT Constructional Details Photo 5 Photo 6 Page 4 of 5 Report No.: LGT26A171 Appendix - External Photographs of EUT Constructional Details Photo 7 Photo 8 Page 5 of 5 Report No.: LGT26A171 Appendix - External Photographs of EUT Constructional Details Photo 9 Photo 10

Label Size:12*30mm Model Number: C2 FCC ID: 2BU2H-2BF2B-C2

Page 1 of 2 Report No.: LGT26A171 Appendix - Internal Photographs of EUT Constructional Details Photo 1 Photo 2 Page 2 of 2 Report No.: LGT26A171 Appendix - Internal Photographs of EUT Constructional Details Photo 3 Photo 4 ANT

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Page 1 of 8 EMF TEST REPORT Product Name: Smart driving recorder Model Number: C2, C2A, C2G, C2K FCC ID: 2BU2H-2BF2B-C2 Issued For : Shenzhen Fuhengye Technology Co., Ltd. Building D2 302, Wanlida Industrial Park, Fuyuan No.1 Road 49th, Heping community, Fuhai Street, Baoan District ShenZhen City Guangdong Province, China Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT26A171HA01 Sample Received Date: Jan. 23, 2026 Date of Test: Jan. 23, 2026 ~ Feb. 03, 2026 Date of Issue: Feb. 03, 2026 Report No.: LGT26A171HA01 Page 2 of 8 TEST REPORT CERTIFICATION Applicant: Shenzhen Fuhengye Technology Co., Ltd. Address: Building D2 302, Wanlida Industrial Park, Fuyuan No.1 Road 49th, Heping community, Fuhai Street, Baoan District ShenZhen City Guangdong Province, China Manufacturer: Shenzhen Fuhengye Technology Co., Ltd. Address: Building D2 302, Wanlida Industrial Park, Fuyuan No.1 Road 49th, Heping community, Fuhai Street, Baoan District ShenZhen City Guangdong Province, China Product Name: Smart driving recorder Trademark: LOOCI Model Number: C2, C2A, C2G, C2K Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC 47 CFR §2.1091 KDB 447498 D01 General RF Exposure Guidance v06 PASS Prepared by: Approved by: Zane Shan Vita Li Engineer Technical Director Report No.: LGT26A171HA01 Page 3 of 8 TABLE OF CONTENTS 1 . GENERAL INFORMATION 5 1.1 GENERAL DESCRIPTION OF THE EUT 5 1.2 TEST LABORATORY 5 2 . FCC 47CFR §2.1091 REQUIREMENT 6 2.1 TEST STANDARDS 6 2.2 LIMIT 6 2.3 EUT OPERATION CONDITION 7 2.4 CLASSIFICATION 7 2.5 TEST RESULT 8 Report No.: LGT26A171HA01 Page 4 of 8 Revision History Rev. Issue Date Revisions 00 Feb. 03, 2026 Initial Issue Report No.: LGT26A171HA01 Page 5 of 8 1. GENERAL INFORMATION 1.1 GENERAL DESCRIPTION OF THE EUT Product Name: Smart driving recorder Test Model Number: C2 Series Number: C2A, C2G, C2K Model Difference: Different resolutions for the front camera. Frequency Bands: 2.4G WLAN 802.11b/g/n(20MHz): 2412~2462MHz Rating: Input: DC 12V 450mA DC/DC ADAPTER: Input: 10-30V Output: 5V 1500mA Hardware Version: C2G-3-3K.260109-V1.0（3K） Software Version: C2G-1296260105-V1.0 1.2 TEST LABORATORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate: FCC Registration No.: 746540 CAB ID: CN0136 Report No.: LGT26A171HA01 Page 6 of 8 2. FCC 47CFR §2.1091 REQUIREMENT 2.1 TEST STANDARDS The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The gain of the antennas used in the product is extracted from the Antenna data sheets provided and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis Transmission formula is far field assumption, the calculated result of that is an over-prediction for near field power density. It is taken as worst case to specify the safety range. 2.2 LIMIT According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of the human exposure to radio-frequency (RF) radiation as specified in 1.1307 (b) Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm²) Limits for Occupational / controlled Exposures 0.3-3.0 614 1.63 *(100) 3.0-30 1842/f 4.89/f *(900/f 2 ) 30-300 61.4 0.163 1.0 300 - 1500 -- -- F/300 1500 – 100000 -- -- 5.0 Limits for General population / Uncontrolled Exposure 0.3-1.34 614 1.63 *(100) 1.34-30 824/f 2.19/f *(180/f 2 ) 30-300 27.5 0.073 0.2 300 - 1500 -- -- F/1500 1500 – 100000 -- -- 1.0 F= Frequency in MHz * = Plane-wave equivalent power density. Friss Formula Friss Transmission Formula: Pd = (Pout * G) / (4*pi*r²) Where Pd = power density in mW/cm² Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = Distance between observation point and the center of radiator in cm If we know the maximum gain of the antenna and the total output power to the antenna, through calculation, we will know MPE value at distance 20cm. Report No.: LGT26A171HA01 Page 7 of 8 2.3 EUT OPERATION CONDITION EUT was enabled to transmit and receive at lowest, middle and highest channels. 2.4 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. Warning statement to the user for keeping at least 20cm or more separation distance from the antenna should be included in the User manual. So, this device is classified as Mobile device. Report No.: LGT26A171HA01 Page 8 of 8 2.5 TEST RESULT Turn up Result Mode Turn up Power 2.4G WIFI-802.11b 15±1dBm 2.4G WIFI-802.11g 14±1dBm 2.4G WIFI-802.11n(HT20) 14±1dBm The MPE result of worst mode: RF Function Max Turn up Power (dBm) Max Turn up Power (mW) ANT Gain (dBi) ANT Gain (gain of antenna in linear scale) Power Density (mW/cm²) Limit (mW/cm²) Ratio Result 2.4G WIFI 16.00 39.81 3 2.00 0.016 1 0.016 Pass Note: 1. The RF Exposure is less than the limit, complies with the exemption requirements. ※※※※※END OF THE REPORT※※※※※

SHENZHENFEIMINTECHNOLOGYCO.,LTD. 1 ShenZhenFeiMinTechnologyCO.,LTD. 产品规格书 Productspecification 客户 CUSTOMER: 产品名称 PRODUCTS:F05 客户料号 PARTNO: 产品型号 Spec.:E.6.050 日期 Data:2023.08.16 REMARK:Pleasesendusone(orcopy)ofthisapprovalwithstampafteraccepting,othercopiesfiled bythecustomer. ADD:Room303,BuildingC,HengnanoneRoad,Gushucommunity,XixiangStreet,Bao’an District,ShenzhenCity 电话Tel:0755-23035723传真Fax:0755-23036702 邮箱E-mail:[email protected] 客户 CUSTOMER 承认 ACCEPTEDBY 审核 CHECKEDBY 批准 APPROVEDBY 供应商 SUPPLIER 拟制 PREPAREDBY 审核 CHECKEDBY 批准 APPROVEDBY CHIP ANTENNA SHENZHENFEIMINTECHNOLOGYCO.,LTD. 2 2 SymbolDimension(mm) L（长度） 3.2±0.20 W（宽度） 1.6±0.20 T（厚度） 1.0±0.20 S（电极宽度） 0.4±0.20 SHENZHENFEIMINTECHNOLOGYCO.,LTD. 3 3 在设计天线时，应远离金属部件和不相关的部件，如电池、振荡器、防护罩、摄像头等，为天线留出 干净的空间。这个间隔简称为净空区。以下是我们建议预留的净空区面积大小。 Whendesigningtheantenna,itshouldbefarawayfrommetalcomponentsandirrelevant componentssuchasbatteries,oscillators,shields,cameras,etc.toleaveacleanspacefortheantenna. Thisintervaliscalledclearancearea.Thefollowingisthesizeofclearanceareawerecommendto reserve. 天线型号（Model） 天线尺寸 （size） 净空区面积 Clearancearea A1（2.4G单极） 5.5*1.2*1.29.1*5.6 X5（2.4G单极） 5.2*2.2*1.08.7*6.5 X6（2.4Gpifa） 3.2*1.6*1.07.0*6.0 D1（2.4G单极） 5.2*2.2*1.08.7*6.5 D2（2.4G单极） 5.2*2.2*1.08.7*6.5 D3（2.4G单极） 3.4*1.7*1.27.2*6.5 F01（2.4Gpifa） 3.2*1.6*0.47.0*6.0 S2（2.4/5.8G双频） 7.0*3.0*2.09.0*7.0 U1(UHF单极） 15.0*3.0*1.019.0*8.0 G2（GPS单极） 9.5*3.0*1.013.5*7.5 F05（2.4Gpifa） 3.2*1.6*1.07.0*6.0 SHENZHENFEIMINTECHNOLOGYCO.,LTD. 4 4 1.3.天线Demo测试板Demo 1.4.建议PCB板尺寸布局SuggestedPCBboardsizelayout UNIT: SHENZHEN FEIMIN TECHNOLOGY CO.,LTD. 5 5 使用以下推荐的匹配和调谐元件值，在我们的标准25*60 mm评估板上，中心频率约为2440mhz。然 而，这些是典型的参考值，当电路板或零件供应商不同时，可能需要更改 。 With the following recommended values of matching and tuning components,the center frequencies will be about 2440 MHz at our standard 25*60 mm evaluation board.However,these are typical reference values which may need to be changed when circuit boards or part vendors are diffierent. 3 4 21 特征Characteristics规范Specifications单位Unit 轮廓尺寸Outline Dimensions 3.2*1.6*1.0mm 工作频率Working Frequency 2400-2500MHz 电压驻波比VSWR <2/ 阻抗Impedance 50 Ω 极化Polarization / 增益Gain 峰值Peak 3 dBi 效率Efficiency 50% 系统匹配电路元件(村田) System Matching Circuit Component（Murata） LocationDesciption Tolerance 10.75pF (0402) ±0.1pF 2NC/ 31.0pF (0402) ±0.1pF 4NC/ SHENZHENFEIMINTECHNOLOGYCO.,LTD. 6 6 2.2.电压驻波比与Smith圆图VSWR VSWRS11 2.3.天线增益与效率Gain 测试系统Testsystem SHENZHENFEIMINTECHNOLOGYCO.,LTD. 7 7 2.4.天线辐射方向图Antennaradiationpattern Frequency(MHz)Gain(dBi)Efficiency(%) 2400MHz 1.4350.15 2410MHz 1.3850.78 2420MHz 1.4950.49 2430MHz 1.3450.43 2440MHz 1.5050.04 2450MHz 1.8752.50 2460MHz 1.9656.12 2470MHz 2.3957.29 2480MHz 2.7558.23 2490MHz 3.0055.99 2500MHz 2.6653.66 SHENZHENFEIMINTECHNOLOGYCO.,LTD. 8 8 [email protected]@2.44GHz [email protected]@2.44GHz 3. 焊接和安装SolderingandMounting SHENZHENFEIMINTECHNOLOGYCO.,LTD. 9 9 指数Index A0B0K0P0PP2 φ D0 WEFT 尺寸 Dimension (mm) 1.8 5 ± 0.1 3.50± 0.1 0.85± 0.1 4.00± 0.1 4.00± 0.1 2.00± 0.1 1.5 0 +0 .1 12.00 ±0.3 1.75± 0.1 3.20± 0.1 0.30± 0.05 1.10链轮孔距累积公差±0.20。10sprocketholepitchcumulativetolerance±0.20. 2.在250毫米中，载体的拱度在1毫米以内。Carriercamberiswithin1mmin250mm. 3.所有尺寸符合EIA-481-C要求。AlldimensionsmeetEIA-481-Crequirements. 4.材料:透明PS。Material:TransparentPS. 5.包装长度每7“卷:12.5米。Packinglengthper7"reel:12.5Meters. 6.组件加载/7”卷:3000个。Componentloadper7"reel:3000pcs.(前后共预留120pcs) IndexABCD Dimension(mm)13.3±0.3100±0.3330±0.324.5±0.3 SHENZHENFEIMINTECHNOLOGYCO.,LTD. 10 1)产品应小心处理，以避免汗水和皮肤油脂损坏或污染。 Productsshouldbehandledwithcaretoavoiddamageorcontaminationfromperspirationandskinoils. 2)对于单个部件，强烈建议使用镊子或真空拾取。 Theuseoftweezersorvacuumpickupisstronglyrecommendedforindividualcomponents. 1)推荐产品从交货之日起6个月内使用。 Recommendedproductsshouldbeusedwithin6monthsformthetimeofdelivery. 2)存储环境条件 Storageenvironmentcondition 温湿度条件:-10~40°C，30~70%RH。 Temperatureandhumidityconditions:-10~40°Cand30~70%RH. 包装材料应保存在空气中不含氯或硫的地方。 Thepackagingmaterialshouldbekeptwherenochlorineorsulfurexistsintheair. 产品应储存在仓库内，无热震、振动、阳光直射等。 Productsshouldbestorageinthewarehousewithoutheatshock,vibration,directsunlightandsoon.

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Page 1 of 54 RF TEST REPORT Product Name: Smart driving recorder Model Number: C2, C2A, C2G, C2K FCC ID: 2BU2H-2BF2B-C2 Issued For : Shenzhen Fuhengye Technology Co., Ltd. Building D2 302, Wanlida Industrial Park, Fuyuan No.1 Road 49th, Heping community, Fuhai Street, Baoan District ShenZhen City Guangdong Province, China Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT26A171RF01 Sample Received Date: Jan. 23, 2026 Date of Test: Jan. 23, 2026 ~ Feb. 03, 2026 Date of Issue: Feb. 03, 2026 Report No.: LGT26A171RF01 Page 2 of 54 TEST REPORT CERTIFICATION Applicant: Shenzhen Fuhengye Technology Co., Ltd. Address: Building D2 302, Wanlida Industrial Park, Fuyuan No.1 Road 49th, Heping community, Fuhai Street, Baoan District ShenZhen City Guangdong Province, China Manufacturer: Shenzhen Fuhengye Technology Co., Ltd. Address: Building D2 302, Wanlida Industrial Park, Fuyuan No.1 Road 49th, Heping community, Fuhai Street, Baoan District ShenZhen City Guangdong Province, China Product Name: Smart driving recorder Trademark: LOOCI Model Number: C2, C2A, C2G, C2K Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC Part 15.247, Subpart C ANSI C63.10-2020 PASS Prepared by: Approved by: Zane Shan Vita Li Engineer Technical Director Report No.: LGT26A171RF01 Page 3 of 54 Table of Contents Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST LABORATORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 9 2.3 TEST SOFTWARE AND POWER LEVEL 10 2.4 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 10 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 11 3. EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.2 RADIATED EMISSION MEASUREMENT 15 4. CONDUCTED SPURIOUS & BAND EDGE EMISSION 24 4.1 LIMIT 24 4.2 TEST PROCEDURE 24 4.3 DEVIATION FROM STANDARD 24 4.4 TEST SETUP 24 4.5 EUT OPERATION CONDITIONS 24 4.6 TEST RESULTS 24 5. POWER SPECTRAL DENSITY TEST 25 5.1 LIMIT 25 5.2 TEST PROCEDURE 25 5.3 DEVIATION FROM STANDARD 25 5.4 TEST SETUP 25 5.5 EUT OPERATION CONDITIONS 25 5.6 TEST RESULTS 25 6. BANDWIDTH TEST 26 6.1 LIMIT 26 6.2 TEST PROCEDURE 26 6.3 DEVIATION FROM STANDARD 26 6.4 TEST SETUP 26 6.5 EUT OPERATION CONDITIONS 26 6.6 TEST RESULTS 26 Report No.: LGT26A171RF01 Page 4 of 54 7. PEAK OUTPUT POWER TEST 27 7.1 LIMIT 27 7.2 TEST PROCEDURE 27 7.3 DEVIATION FROM STANDARD 27 7.4 TEST SETUP 27 7.5 EUT OPERATION CONDITIONS 27 7.6 TEST RESULTS 27 8. ANTENNA REQUIREMENT 28 8.1 STANDARD REQUIREMENT 28 8.2 EUT ANTENNA 28 APPENDIX I - TEST RESULTS 29 1. DUTY CYCLE 29 2. BANDWIDTH 33 3. MAXIMUM CONDUCTED OUTPUT POWER 40 4. MAXIMUM POWER SPECTRAL DENSITY 41 5. UNWANTED EMISSIONS IN NON-RESTRICTED FREQUENCY BANDS 45 APPENDIX II - MEASUREMENT PHOTOS 54 Report No.: LGT26A171RF01 Page 5 of 54 Revision History Rev. Issue Date Revisions 00 Feb. 03, 2026 Initial Issue Report No.: LGT26A171RF01 Page 6 of 54 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 15.247 Meas Guidance v05r02. FCC Part 15.247,Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS -- 15.247 (a)(2) 6dB Bandwidth PASS -- 15.247 (b)(3) Output Power PASS -- 15.209 Radiated Spurious Emission PASS -- 15.247 (d) Conducted Spurious & Band Edge Emission PASS -- 15.247 (e) Power Spectral Density PASS -- 15.205 Restricted Band Edge Emission PASS -- Part 15.247(d)/ Part 15.209(a) Band Edge Emission PASS -- 15.203 Antenna Requirement PASS -- NOTE: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2020. Report No.: LGT26A171RF01 Page 7 of 54 1.1 TEST LABORATORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate: FCC Registration No.: 746540 CAB ID: CN0136 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. Occupied Channel Bandwidth ±0.46% RF Output Power, Conducted ±0.71dB Power Spectral Density, Conducted ±1.57dB Unwanted Emission, Conducted ±0.63dB Conducted emission ±2.80dB All Emissions, Radiated (0.009-30MHz) ±2.16dB All Emissions, Radiated (30MHz-1GHz) ±4.61dB All Emissions, Radiated (1GHz-18GHz) ±5.49dB Temperature ±0.5°C Humidity ±2% Duty Cycle ±2.3% Note: The measurement uncertainty is not included in the test result. Report No.: LGT26A171RF01 Page 8 of 54 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name: Smart driving recorder Test Model Number: C2 Series Number: C2A, C2G, C2K Model Difference: Different resolutions for the front camera. Product Description: Operation Frequency: 802.11b/g/n(20MHz): 2412~2462MHz Modulation Type: 802.11b(DSSS):CCK,DQPSK,DBPSK 802.11g(OFDM):BPSK,QPSK,16-QAM,64-QAM 802.11n(OFDM):BPSK,QPSK,16-QAM,64-QAM Number of Channel: 802.11b/g/n(20MHz): 11CH Antenna Designation: Chip Antenna Antenna Gain(dBi): 3 Channel List: Please refer to the Note 3. Rating: Input: DC 12V 450mA DC/DC ADAPTER: Input: 10-30V Output: 5V 1500mA Hardware Version: C2G-3-3K.260109-V1.0（3K） Software Version: C2G-129626…

Text truncated - open the document above for the full version.

Page 1 of 2 Report No.: LGT26A171 Appendix - Test Setup photos Set-up for Radiated Spurious Emission, Below 1GHz Set-up for Radiated Spurious Emission, Above 1GHz Page 2 of 2 Report No.: LGT26A171 Set-up for Conducted Emission